SPECIAL REPAIR TO SECURITY GUARD ROOM (P-6) OF CQA (ICV) AND CERTAIN MINOR WORKS UNDER AGE (I) FY , EDDUMAILARAM

Amount

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars,etc, but excluding ashlarfacings, dressed stonework and precast concrete articles.

Dismantling of floor, hearth or wall tilling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete.

Taking down chowkhats or frame not exceeding 1.5 Sq. m each with shutter(s) (without taking off shutters from the frame), complete all as specified.

Taking down Chowkhats or frames with shutters exc 1.5 sq. m but n exc 4 sq. m (without taking off shutters from the frame). complete all as specified and directed.

Demolition and breaking up 100mm dia drain pipes (salt glazed wire AC or reinforced concrete) set in cement mortar

Taking down cement or cement lime plaster of any description on brick/stone or concrete surfaces etc including raking out joints,hacking for key and scrubbing down with water upto 4 storeys building complete all as specified and directed by Engineer-in-Charge.

M&L for brick work with subclass 'B' bricks, straight or curved on plan exc 6 M mean radius built in CM 1:6 all as specified.

First quality, group-IV, non-skid ceramic, straight cut/joint free, 7-8 mm thick colored tiles, area of each tile exceeding 0.18 sq.m but not exceeding 0.38 Sq.m, in floors etc. over 15mm thick 1:4 cement mortar screed, set and jointed with grey cement slurry & pointed with grout of matching shade, complete, all as specified.

ditto as above but for vertical surfaces such as skirting, dados and riser to steps

M&L for Coloured printed Non Skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed (colour & design approved by Engr -in-Charge).

M&L for Coloured printed Glazed ceramic tiles on vertical surface 350 x 250 x 7 mm/450 x 350 x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles complete all as specified and as directed (colour & design approved by Engr -in-Charge).

M&l 25 mm thick PCC floor type B-1:2:4(20 mm graded crushed stone aggregated) laid as backing complete all as specified and directed

M&L for screed bed or bedding layer, 15 mm thick in cement morter (1: 6) for laying tile/Kota stone on floor surface complete.

M&L for 10 mm thick plastered surfaces in 1:4 cement mortar, to receiving tiles/kota stone on vertical surfaces as specified as directed.

M&L for rendering CM (1:6) 15 mm thick on fair faces of brick work or concrete surfaces or for laying floor finishes even and smooth without using extra cement

M&L for rendering CM (1:3) 5 mm thick on ceiling, soffits etc of brick work or concrete surfaces surface even and smooth without using extra cement.

M&L for 15 mm thick rendering on fair faces of brick work or cement concrete surfaces in cement mortar 1:4, finished fair and even without using extra cement incl mixing of water proofing compound complete all as specified. (Note: Water Proofing compound shall be measured and paid for separately)

Supply only water proofing compound

M&L for 100 mm thick in Plain cement concrete type D2 ( 1:4:8) ( using 40 mm graded aggregate ) as sub base etc, all as directed.

M&L for Chequered cement concrete tiles 30cm x30cm x 22 to 25mm, set with grey cement and no pigment, jointed and pointed in neat cement slurry in floor complete over 20mm thick screed bed in CM 1:4 all as specifed.

S&F Pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate incl filling hollow of frame with plain cement concrete type B0 (1:3:6 )(using 12.5mm graded aggregate ,etc complete all as specified as directed.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire of average width of aperture 1.40mm fixed with stainless steel wire staples

Factory made, 35mm thick 2nd class hard wood, plain framed, paneled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both sides, the side of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, 35 mm thick complete, all as specified and directed by Engr-in-Charge.

Factory made, 2nd class hard wood,35mm thick glazed and skeleton shutters, open rebated and prepared to receive glass / gauge etc. (without sash bars) edges or framing plain, chamfered or rounded fitted with cut or mitered beads for securing glass etc. size of members of shutters as specified in SSR Part - I section 8.20 (a), all as specified and directed by Engr-in-Charge.

Powder coated aluminium frame for doors, windows, ventilators, fixed glazing with one or more rebates including joining cleat for fixing, fixed to opening with suitable size steel screws and rawl plugs etc., (aluminium section not less than 2 mm) complete all as specified.

Anodised aluminium powdewer coated window and ventilator shutters, side hung type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

Anodised aluminium powder coated door shutters, aluminium section weighing 0.55 kg/m including ecessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified

Double action floor door spring, hydraulically regulated, made of 1.25 mm thick aluminium alloy sheet, foundation box main body with stainless steel cover, governing pivot made of brass, rest of part made out of heavy duty mild steel, ISI marked, complete.

Plain Sheet glass 5.5 mm thick, ordinary quality and glazing with linseed oil pane putty & spring glazing clips, in squares exceeding 0.5 Sq. mm in each pane, complete all as specified.

Solar control film, having thickness not less than 25 micron, reflective type complete all as specified. MAKE: GARWARE SUN CONTROL OR EQUIVALENT.

Mortice lock, brass body, 4 lever, 100 mm size, vertical type with two keys, complete all as specified.

M&L for preparation of new surface and applying three coat of white wash on ceiling all as directed and specified.

Preparation of new plastered surfaces of wall and applying two coat of OBD on a coat of putty not less than 2mm thick all as specified and as directed.

M&L one coats synthetic enamel on old steel surfaces of any description not otherwise described over 10 cm width or girth including preparation of surfaces. complete all as specified.

M&L one coats synthetic enamel paint on old wooden surfaces of any description not otherwise described over 10 cm width or girth including preparation of surfaces. complete all as specified.

Preparation of new wooden or wood based surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, all as specified.

M&L for one coat Cement base paint to plastered or unplastered surfacesof walls incl preparation and washing, rubbing down old treated surfaces

M&L for two coats Cement base paint to plastered or unplastered surfacesof walls incl preparation of new surfaces

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm double side prelam PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing complete all as specified.

S&F Factory Made Solid PVC Moulded Door Shutter with Particle Board Core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified.

S&F 100 mm long butt hinges medium weight mild steel alloy with galvanised .

S&F aluminium anodised, barrel tower bolts of extruded section and length of bolt 75 mm complete all as specified.

Hacking out old broken glass (any thickness, size, quality or description) from metal frames including punching or drilling out old glazing pins or spring clips and providing and fixing new clips or pins, all as specified.

S&F sheet glass ordinary quality and glazing with oil putty in square n. exc 0.50 Sqm in each pane 3mm thick all as specified

Taking out of existing water proofing treatment if any complete on roof surface and surface properly cleaned complete all as specified and as directed by Engineer-in-Charge.

M&L for 10mm thick rendering in CM 1:4 on brick or concrete surfaces as in roof treatment with WPC(WPC paid separetly)

M&L Wire brushing and cleaning top surface of tiles, lime terracing or cement concrete, including flashings and junction of parapets, etc., and surface painting, with a layer of blown grade bitumen of any penetration applied hot @ 1.7 kg per sq. m, blinded with grit or pea size gravel @ 0.006 cu.m per sq.m, and lightly tampered (area of flashings, etc., shall be added to the roof area) and APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified.

Dismantling water tanks exc 500 but n .exc 1000 ltrs and removing to store complete all as specified and directed by engr in charge

S&F 1000 litre rotational white colour moulded polythene water storage tank (cylinderical vertical) tripple layer with closed top hoisted and fixed in position all as specified in SSR Part-I

S&F 20 mm Gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed

S&F steel water tubing, 15mm dia, galvanised, medium grade, ISI marked with and including taking down and all fittings and fixed on walls and ceilings or laid in floor complete all as specified and directed.

S&F steel water tubing, 20mm dia, galvanised, medium grade, ISI marked with and including taking down and all fittings and fixed on walls and ceilings or laid in floor complete all as specified and directed.

S&F 20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed. ( minimum weight 142 gms)

S&F in repair Vitreous china squatting pan of pattern Orissa Pattern size 580x 440 mm white with ‘P’ or ‘S’ trap , front or back inlet but excluding flushing cistern and flush pipe fixed in repair including placing in position in floor and embedded in cushion of PCC 1:7:12 type E-1 and finishing the top surfaces to match with the existing flooring..(Make: - Hindware/ Parryware/ Johnson )

S&F in repair PVC (Plastic polymer Cistern) valve less, Symphonic action type, flushing cistern of capacity 10 liters, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete including taking down by dismantling the existing unserviceable cistern of any description.(Make: - SLIMLINE (ECONOMY) with front knob of Parryware or equivalent in Hindustan Sanitary ware)

Urinal, bowl type or half stall pattern, basin only including connections to flushing pipe and outgoing pipes fixed in repairs

Vitreous China wash basin, white, flat back, size 550 x 400 mm, including fixing acessories like galvanised brackets & rag bolts, IN REPAIR, complete.

S & F 110 mm dia PVC (SWR) pipes double socketed, in any length with rubber ring joints fixed to walls.

S&F PVC SWR floor trap with grating including jointing with solvent cement 75 mm dia.

S&F in repair Bib taps,,chromium plated with crutch or butterfly handle screwed down for iron pipe or for brass ferrule and fixed for bore of pipe 15 mm, fixed in repair, all as specified. Make- Prayag

S&F in repair Stop valves fancy type, chromium plated, cast copper alloy, with long shank and cup screwed for iron pipe or for unions of bore dia 15mm and fixed, all as specified.

S & F in repairs towel rails chromium plated of 20mm dia and 600mm long complete all as specified and directed.

S & F repair CP Soap dish complete all as specified and directed.

S&F 15mm bore PVC connection 450mm long with brass nuts on both ends complete all as specified.

Surface excavation n.exc (not exceeding) 30cm deep and averaging 15cm deep and getting out in any type of soil complete, all as specified.

Cutting chases pinning in making good to facings where required and pointing in cement mortar 1:3 to ends, or edges of landings etc and cutting chases for concealead water tubing or inserting steel sheet in wall n.exc 10cm girth in brick wall complete all as specifeid

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard / dense soil.

Returning filling in including spreading, levelling watering and well ramming in layers n exc 25 cm

Removing excavated material exc 250 M and not exc 500m deposited where directed.

M&L for cement concrete (1:4:8) type D2 using 40 mm graded aggregate) as in foundation filling and mass concrete

M&L for cement concrete (1:2:4) type B1 using 20 mm graded aggregate) as in coping /benching etc all as specified and directed

M&L broken stone or boulders hard core of gauge of n exc 63mm deposited spread levelled in layers all as specified and directed

75 mm thick, cement concrete type C-2, 1:3:6 using 40 mm graded stone aggregate, finished even & rough, as in sub floors, complete all as specified.

40 mm thick, cement concrete type B-1, 1:2:4 using 20 mm graded stone aggregate, finished even & smooth, using extra cement as in floors, complete all as specified.

M&L 50mm thick PCC (1:3:6) type C1, using 20mm graded stone aggregate as in plinth protection finished even and smooth with out extra cement.

Cutting holes into or through RCC/brick walls built in cement mortar not exceeding half brick thick for inserting angle/tee/pipe/ hold fast or similar purposes etc. and making good in cement mortar 1:3 or cement concrete 1:2:4, Type B-1 as required complete all as specified.

Mild steel rolled sections as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming to grade Fe-410-Gde E-250, complete all as specified.

S&F pre- painted galvatum aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, self tapping screws all as specified.

S&F framed work as in doors ar gates of angle or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering doors, etc to be prepared for hanging or sliding with and incl either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering running rails and guides ) and hanging also fastening and fixing complete.

Cement concrete, type B-1 (1:2:4), using 20 mm graded stone aggregates as in lintels up to 1.5 metre clear span, bed blocks, copings and the like including weathering, slightly rounded or chamfered angles & throating including provision of necessary formwork, complete all as specified.

Factory made steel windows with side hung shutters including box type hinges, steel handle, mild steel ISI marked tower bolt 100 mm size (minimum 2 for each shutter), and steel peg stay, complete with glazing bars, dovetailed or welded with one shop coat of zinc chromate primer, complete all as specified.

Factory made steel windows with side hung shutters including box type hinges, steel handle, mild steel ISI marked tower bolt 100 mm size (minimum 2 for each shutter), and steel peg stay, complete without glazing bars, dovetailed or welded with one shop coat of zinc chromate primer, complete all as specified.

M&L for two coats of synthetic enamel paint over a coat of red oxide primer to steel surfaces of any description over 10 cm width or girth incl preparation of new surface.

Three coats of white washing on new/undecorated wall surfaces, including preparation of surfaces, complete all as specified.

Excavating Soft Loose soil in post holes each n.exc 0.5 cu.m getting out, returning, filling in and ramming earth or broken rubble mixed with each around in layers not exc 25cm watering and removing surplus soil to a distance n.exc 50m and making good surface.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire

Supply only Chain link MS galvanisd fencing, 3mm thickness of wire and 70x70mm size all as specified and directed

M & L Cement concrete Type C2 1:3:6 (40 mm graded aggregate) as in boundary pillers, post columns etc all as specified and directed.

S&F Mild steel as in hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 ®complete all as specified and directed

M&L Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut of diameter of neck 5 to 10 mm, length of bolt exc 10cm and n exc 15cm long

M&L MS bars Fe-410-W (Gde E 250) 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips. etc.

Excavating over areas n.exc 1.5m deep and getting out complete soft loose soil.

Walling of Square rubble, regular coursed, well bonded, bedded and solidly hearted, built in CM 1:6

M & L for rendering 15 mm thick in CM (1:3) on fair faces of brick work, Stone masonry or concrete surfaces finished even & smooth without using extra cement

PCC type C-2 (1:2:4), using 40 mm graded stone aggregates as in filling & mass concrete, complete all as specified.

PCC type C-2 (1:3:6), using 40 mm graded stone aggregates as in surface channels and drains, complete all as specified.

M & L for PCC 1:4:8, type D-2, using (40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified.

M&L in repairs 25mm bore tubes medium grade galvanised, with all fittings laid in trunches.

S&F gun metal 25mm gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.

Demolition of cement Concrete in ground floors and pavings n.exc 15cm thickness (below or above ground level) all as specified and directed.

M & Light coloured vitrified tiles 10mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match.

-Do- all as above item no 06 but in skirting All as specified and as directed.

Taking down wooden shutter and refixing in same opening after resecuring or easing and adjusting of size exc 1sqm and n.exc 2sqm all as specified and directed

Taking down carefully aluminium point wiring for (light, fan, socket or power) with all fittings and fixtures such as switches, ceiling roses, pendents, regulators, sockets, light fittings, etc, removing materials to taking credit and making good disturbed surfaces of walls, ceilings, etc complete all as specified and directed by Engineer-In Charge.

M&L for concealed conduit point wiring complete with FRLS PVC insulated, unsheathed cable 1100 V grade conforming to IS-694, 1.5 sqmm (nominal area) multi-stranded with metalic rigid PVC conduit medium grade not less than 20mm dia (ISI marked ) and conduit accessories fixed on MS terminal boxes made out of 16 guage mild steel sheet with hold fast flushed to wall with, 3mm thick laminated sheet cover for mounting of switches, socket outlets, regulators etc, including provision of FRLS PVC insulated, unsheathed multistranded copper conductor of size 1.5 sqmm as earth dolly complete all as specified and directed for the following :- (Make of cable: Havells ISI Marked. Make of PVC conduit : Sudhakar ISI Marked.) (a) One light/exhaust fan &ceiling fan point controlled by one, one-way switch & one switch and regulator

(b) One 3 pin socket outlet 5 Amps, 230 volts on independent board

(c) One 3 pin socket outlet 5 Amps, 230 volts on same board

All as per item No. 3 above but with 2.5 Sqmm cable for one 3 pin 5/15 Amps switch socket outlet on independent board with copper conductor of size 2.5 Sqmm as earth continuity conductor complete all as specified and directed by Engineer-In Charge.

S & F, Switch Piano, flush type, single pole, one way, 5 Amps, 240 Volt complete all as specified and directed by Engineer-In Charge. Make : Anchor / Havells/Legrand

S & F switch Piano, flush type, single pole, one- way, 15 Amps, flush type, universal ISI marked complete all as specified and directed by Engineer-In Charge. Make : Anchor / Havells/Legrand

S & F stepped type electronic fan regulator, flush type complete all as specified and directed by Engineer-In Charge .Make : Anchor / Havells/Legrand

Supply and fixing ceiling rose surface, 65x20mm size three terminals ISI marked complete all as specified and directed by Engineer-In Charge. Make : Anchor / Havells/Legrand

S & F Socket outlet 2 in 1, 5 Amps, flush type, multi purpose universal fixed on the same board complete all as specified and directed by Engineer-In Charge. Make : Anchor / Havells/Legrand

S & F socket out let, 2 in 1, 5 and 15 Amps, flush type, universal ISI marked complete all as specified and directed by Engineer-In Charge. Make : Anchor / Havells/Legrand

S&F Surface mounting Batten for 1 x 20 Watts LED T-5 / T-8 tubes, 230 Volts, wall / ceiling mounted type with all internal connections connector block with all accessories and connecting up with and including twin core twisted flexible copper conductor cable of suitable size complete all as specified and as directed Engineer-in-Charge. Make: Havells Cat No. REGALBATTEN8UP TO1X22WSSBSWH/or crompton /Philips

S&F LED luminairies (Tube rod) of 1 x 20 Watts, 230 Volts, Ultra bright aluminium heat sink LED Tube light of 6500K luminious intencity with high efficency suited for installation in batten complete all as s pecified and as directed by Engineer-in -Charge. Make: Havells Cat No. Crystal 1213T8 DSTL20WLED865 glass/Philips/CG

Supply and fix surface mouting LED luminairies 1x15 watts, 230 volts, wall/ceiling mounted type suitable for B22 base with all internal connections connector block with all accessories and connecting up with and including twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-In Charge. Make : Havells Cat No : LHDL07150099 or equivalent in CG/Philips.

Taking down carefully wooden/MS boxes of any size and any pattern complete with all enclosures/ components includung making good to the disturbed surfaces complete all as specified and directed by Engineer-In Charge.

S & F sheet metal enclosure for SPN DB 8 way double door, 240 volts with 200 Amps rated bus bar, IP-43 protection, shrouded neutral bar, bus bar, cement spill protector complete all as specified and directed by Engineer-In Charge. Make : L&T/Scheinder/Legrand/Havells

S & F MCB Double pole Pole, 240 V, 40-63 Amps, 'C' series, complete all as specified and directed by Engineer-In Charge. Make : Scheinder/Legrand/HavellsL&T

S & F MCB, SP, 240 V, 6 to 32 Amps, 'C' serie, complete all as specified and directed by Engineer-In Charge. Make : Scheinder/Legrand/Havells/L&T

M&L for sub main wiring with two runs of single core 1100 volts grade, FRLS PVC, insulated, unsheathed, multistranded copper conductor cable of size 4.0 Sqmm, drawn through and including non-metallic rigid PVC conduit 20mm dia and conduit accessories including provision of one run of FRLS PVC insulated 2.5 Sqmm multistranded copper earth continuity conductor in concealed wiring including taking down old sub main wiring complete all as specified and directed. [NOTE: 2 runs of 4.0 Sqmm cable, 1 run of 1.5 Sqmm cable and 1 run of PVC conduit shall be measured as one unit length.]

Supply & Fixing only security light 40 watt LED fittings complete with driver and , suitable for mounting on 40mm or 50mm dia existing GI mast or bracket arms with pole fixing attachments complete all as specified and directed by Engr-in Charge. Make : HAvells/Crompton/bajaj

M/S Veerabhadra Constructions