ADDN /ALTN CUM SPL REPAIR TO CERTAIN OR MD ACCN OF INF BN AT DEHRADUN CANTT

Amount

Dismantling asbestos cement (corrugated , semi corrugated, etc.) sheets in roof coverings.Complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern as in roof coverings.Complete all as specified and directed.

Dismantling timber scantling 40 sqcm & over in section uframed in any position. Complete all as specified and directed.

Dismantling wall and ceiling boards, fibre or pulp, insulation etc. in insulation boards slabs, blankets any thickness incl cover fillets.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete as directed and specified.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc.Laid, bedded and pointed in any mortar complete as directed and specified.

Demolition of cement concrete (un reinforced) in ground floor and paving n. exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of brick work in cement mortar including all quoins, arches, pillars etc, but excluding ashler facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Taking down cement plaster of any description, thickness on brick, stone, concrete surfaces including racking out joints, hacking for key, scrubbing down with water, removal of rubbish and cleaning, etc complete as directed and specified.

Taking down Chowkats or frames with shutters (without taking off shutters from the frame) exc 1.50 sqm but n.exc 4.0 sqm each and removing from site including making good disturbed portions of wall with new or old bricks, lintel, cills etc in CM 1:4 complete all as specified and directed.

Taking down Chowkats or frames with shutters (without taking off shutters from the frame) n.exc 1.50 sqm each and removing from site including making good disturbed portions of wall with new or old bricks, lintel, cills etc in CM 1:4 complete all as specified and directed.

Taking down shutter of any description exc. 1.0 Sqm but n.exc 2.0 Sqm each and removing from site complete all as specified and directed.

Taking down shutter of any description exc 2.0 Sqm each and removing from site complete all as specified and directed.

-Blank-

-Blank-

Dismantling of cast iron/ PVC /AC /SGSW pipes alongwith fittings and accessories upto 100 mm dia jointed in cement mortar and taking out of walls, floors or trenches, if required complete all as specified and directed.

Dismantling Mild Steel work of any description not otherwise provided for complete all as specified and directed by Engr-in-Charge

Taking up or down 15 mm steel tubing and connections complete all as specified and directed.

Taking up or down 20 mm steel tubing and connections complete all as specified and directed.

M&L PCC D 2, 1:4:8 75 mm th (40mm graded aggregate) in floor sub base

M&L Machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete ncl screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6. Complete all as specified and directed.

M&L Machine Kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete incl 10 mm thick rendering on brick surface in CM 1:4. Complete all as specified and directed.

M & L for 25 mm thick PCC 1:2:4 type B-0, using 12.5 mm graded stone aggregate as in floors, to receive surface of tile complete all as specified and directed.

M & L for Glazed vitrified tiles(GVT) 7 to 8 mm thick (square/ rectangular) of size 600 x 600 mm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6,complete all as specified and directed.

M & L for Glazed vitrified tiles(GVT) 7 to 8 mm thick (square/ rectangular) as in Skirting, riser etc (length of tiles not less than 600 mm) set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in CM 1:4 complete all as specified and directed,

M & L for non-skid coloured ceramic joint free tiles 7 to 8 mm thick (square/ rectangular) of size 400 x 400 mm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6,complete all as specified and directed.

M&L Glazed ceramic tiles coloured 300mmx 450mm , 7 to 8 mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match on vertical surfaces of wall incl 10 mm thick rendering on brick surface in CM 1:4. complete all as specified and as directed.

M & L 15 to 18 mm thick granite(Zed Black colour as approved by GE) stone slab machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing as in kitchen platform/dado/skirting /platform counter top WHB including cutting holes for oval shape /urinal partitions etc. including 15 mm thick cement screed bed 1:6 CM in horizontal or vertical surfaces including grinding the edges half round and polishing complete all as specified and directed by Engineer-In- Charge.

M&L 75mm thick PCC 1:3:6 type C-2, (20 mm graded stone aggregate)as plinth protection and finishing even and smooth without using extra cement incl making joints 12 mm wide of full depth of PCC at every 3 meters and at every change in direction and filling the same with sealing compund grade 'A' incl necessary formwork. Complete all as specified and directed.

M&L for brick work with old size bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:6) complete all as specified and directed.

Ditto, but except bricks incl cleaning cement mortar from dismantled bricks

M&L for 15mm thick rendering in cement mortar 1:6 to on brick masonary wall surfaces or on other than fair faces of brick masonary finished even and fair without using extra cement complete all as specified and directed.

M&L for 15mm thick rendering on fair faces of brick/ concrete surfaces in CM 1:4 finished even and fair. Complete all as specified and directed.

M&L for extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work 15 to 30 cm in width or girth; including cutting to edges, all mitres and stopped ends etc.complete all as specified and as directed

M & L 595 mm x 595 mm false ceiling system , using hot dipped galvanised steel section exposed surface with precoated capping, GI tee (Galvanised @120 grms, both side inclusive and black painted groove on all T webs) and cross tee of size 24 x 32 mm & 24 x 27 mm having 0.27 mm gauge at every 600 mm c/c interval and wall angle of size 19 x 19 mm having 0.35 mm gauge fixed to the wall. The above grid is to be suspended at every 1200 mm c/c in both direction using 2mm thick pre-straightened GI wire laying designer tile ivory painted (high pressure steam cured) of 4 mm thickness (as per IS 14862) of size 595 x 595 mm and ant ine of the design e-board (cascadev or electra) , back of the tile duly sanded and finished with a coat of protective paint over the formed grid etc complete all as specified and directed.

“S&F factory made single extruded WPC (Wood polymer composite) Solid moulded Flush Door Shutter (pre laminated both sides) of 30 mm size comprising of virgin PVC resin of K value 58-60 (Suspension Grade), Calcium Carbonate and natural Fibers (Wood Powders/ rice husk/ wheat husk) and Non toxic additives (max toxicity index of 12 for 100 gms) having min density of 650 kg/Cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge) Minimum Compressive Strength of 50N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of class A category with property of being Termite/Borer proof. Water/ Moisture proof, Fire retardant and fixing with stainless steel but hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer-in-charge, Material test certificate and authentication should be compulsory provided by the manufacturing company.

“M&L for 30 mm thick factory made solid WPC (Wood plastic composite) gauged door shutter with wire mesh in three number of division with brown wood grain texture, incl S S wire mesh fixed with 15X15 mm square tubes in side rails with screwing 8X28 heat metal zinc coated screws that can be removed or fixed again after changing of wire mesh when needed covered with moulded beading. The density of the WPC material shall be as per manufacturer instruction. Complete all as specified and directed.”.

-Blank-

-Blank-

S & F factory made WPC single extruded 100% lead free ROHS certified board of 18mm thick pre laminated shutter for kitchen, cupboards. The laminated shutter should be pre laminated side with different design and other side plain white of density not less than 600 kg / cum manufactured by an ISO 9001:2015 certified company. The 18mm board should be 100% lead free, water proof, termite proof and borer proof and should have good screw holding capacity and complete all as specified and directed.

Supply& fixing factory made single extruded WPC (Wood polymer composite) Solid door frame / chowkhat of size 100X65. Comprising of virgin PVC polymer of K value 58-60 (suspension grade) calcium carbonate and natural fibres (Wood powder/rice husk/wheat husk) and non toxic additives (max toxicity index of 12 to 100 gms) fabricated with mitred joints and applying PVC solvent cement and screwed with full body threaded star headed SS screws having min frame density of 750 Kg/cum screw withdrawal strength of 2200 N (face) & 1100 N edge, minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class ‘A’ category with property of being termite / borer proof, water /moisture proof & fire retardant & fixed in postion with SS dash fastners/ hold fast of required dia and length, colour of door frame to match that of shutter all as specified and directed

-Blank-

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) windows (3 Track / Openable) for frame/ shutters /track of windows & ventilators including providing and fixing hinges/ pivots/roller locking arrangement incl fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per the directions of Engineer-in-charge

S&F for mild steel window grills box type framed work as in window guard bars, grills or forged into spikes, framed balusters, walkway railing and similar work including welding, FE-290 grade E-165 complete all as specfied and directed.

S&F sheet glass ordinary quality 4mm thick and glazing with oil putty or fixed with bead/ glazing pins in squares n.exc. 0.5 sqm each pane complete all as specified and directed.

S&F 4 mm thick Figured glass, pin head type and glazing with oil putty in squares n.exc 0.5 sq. m in each pane complete all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainles steel wire stapel etc complete all as secified and as directed

S&F Stainless steel tower bolt 200 mm long. complete all as specified and as directed

S&F Stainless steel sliding door bolt size 250 mm long and dia 12 to 16 mm with hasp, staple (bolt type) including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed. Complete all as specified and directed by Engr-In-charge.

S&F 150 mm long SS handle, complete all as specified and as directed

S&F 100 mm long SS handle (fancy type) for cabinet and CB shutter, complete all as specified and as directed

S&F SS double legged floor door stopper 150 mm long with rubber etc complete all as specified and as directed

S&F bal catches with 8 mm dia steel ball magnet catches for cuboard shutter including strking plate as approved etc complete all as specified and as directed

S&F mild steel helical door spring 150 mm long ordinary rat tail type incl roller and roller plate complete fixed with screws to wooden frames or with welding to steel frames complete all as specified and directed

S&F stainless steel (Grade SS 202) decorative curtain rod of 25 mm bore.complete all as specified and as directed

S & F hydraulic concealed hinge with clip on installation and integrated Silent System, opening angle not less than 100º, For shutter thickness 15 - 24 mm full overlay type shutters, hinge cup dia 35 mm including necessary fixing arrangement with SS screw complete all as specified & directed.

S & F for stainless steel glossy finish hat peg set of five tier with necessary fitting complete all as specified and directed.

S&F in repairs 500 litre rotational moulded tripple layer polyethlene water storage tanks white colour (cylindrical vertical with closed top) and suitable size of MS tasla with locking system hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

S&F 20mm ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed etc complete all as specified and as directed

S&F as in repair Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe 20 mm bore and fixed as in repair complete all as specified and as directed

M & L for cutting chases, pinning in brick/PCC blocks wall in making good to facings where required and pointing in cement mortar 1:3 and cutting chases for concealed water tubing etc and making good complete all as specified and as directed

S&F medium grade galvanized steel tubing with all fittings &fixed complete to walls & ceiling or laid in floors 15 mm dia bore pipe (including in short length) complete all as specified and as directed

S&F tubes medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors 20 mm dia bore pipe (including in short length) complete all as specified and as directed

S&F in repairs vitreous chinaware coloured wash hand basin with pedestal of size 55X40 cm complete including fancy CP pillar tap, CP brass waste coupling ,waste pipe including fixing arrangement and cutting for and pinning in walls & making good complete all as specifed and directed.

S & F in repair fancy type 125mm size square brass CP shower rose with or without swivel joints complete all as specified and as directed.

S & F Brass CP wall mixture(3 in 1) 15 mm bore (wall mounted type) for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and as directed

S & F Brass CP sink mixer 15mm bore (wall mounted type) for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and as directed

S&F in repair bib tap long body fancy type cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule or fixed for 15 mm dia bore pipe complete all as specified and as directed

S&F in repair stop valves/angle valves fancy type chromium plated brass cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions fixed for 15 mm dia bore pipe complete all as specified and as directed

S&F in repair tubular towel rail 20mm dia type brass chrormium plated 600mm long between flanges complete all as specified and as directed

S&F in repair PVC connection of 45 cm length including brass nuts complete all as specified and as directed

S&F fancy type brass chromium plated soap dish of 160x160x90 mm complete all as specified and directed.

S&F fancy type glass corner 300mm radius of 10mm thick toughned glass with CP railing fixed with fancy type screws complete all as specified and directed.

S&F in repairs vitreous china squatting pan orissa pattern long pan size 580 mm x440mm white with spun pipe ‘P’ or ‘S’ trap, front or back inlet and foot rests excluding flushing cistern & flush pipe but incl. cement concrete bedding fixed complete all as specified and as directed

S&F in repair PVC low level flushing cistern 10 litres, valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, flushing pipe complete all as specified and directed.

S&F in repair for 75 mm bore out let cast floor trap spun pipe (conforming to IS 3989) incl cockroach trap with gratings including jointing to waste pipe fixed in cement concrete tpe B-1 (1:2:4) etc complete all as specified and as directed

S&F for 75 mm bore Cast iron spun pipe (conforming to IS 3989) soil, waste and vent pipes, in any length with or without ears , laid in trenches or in floors or fixed to wall vertically complete all as specified and as directed

S&F for 100 mm bore Cast iron spun pipe (conforming to IS 3989) soil, waste and vent pipes, in any length with or without ears , laid in trenches or in floors or vertically cast, complete all as specified and as directed

S&F 100 mm bore cast iron Bends of (any radius), spun pipe (conforming to IS 3989) diminishing piecs or tapers (larger bore measured) complete all as specified and as directed

S&F for 50 mm bore Cast iron spun pipe (conforming to IS 3989) soil, waste and vent pipes, in any length with or without ears with lead joints fixed to wall vertically complete all as specified and as directed

S&F 50 mm cast iron cowls spun pipe (conforming to IS 3989) complete all as specified and as directed

S&F kitchen plate rack stainless steel 1 mm thick of size 90cmx75cm complete fixed to brick/concrete wall, with screw including rawl plug complete all as specified and as directed

S&F in repair stainless steel sink with drainage board 1.00mm thick for kitchen with plug/waste pipe washers including cantiliver bracket or, connecting unions etc over all size 915 x 460mm with bowel size 410mm x 330mm x 160mm complete all as specified and as directed

S&F MS joist channel (Fe 410-W Gde E-250 Quality A), angle or Tee section MS tubes, flats square bars etc fixed indepently or framed or without connecting plates ,trusses etc any type framing including purlins and rafters etc confirming to Grade Fe 410-0 or Fe-310-0 complete all as specified and directed by Engr-in-Charge

Erection and fixing only Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates

S & F pre-painted galvalume aluminium zinc coating GI based corrugated steel 0.50 mm thick of any colour as directed by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge

S & F pre-painted galvalume aluminium zinc coating GI based plain steel 0.50 mm thick for ridge cover of any colour as directed by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge

S&F framed work as in doors or gates of angle or other section Fe 410 W Gde E 250 with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

S&F 1.25 mm thick mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete including cutting out of existing sheet if required complete all as specified and directed.

Supply & fixing factory made single extruded WPC (Wood polymer composite) Solid door frame/chowkhat of size 150X65 (Double rebate) comprising of virgin PVC polymer of K value 58-60 (suspension grade) calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (max toxicity index of 12 to 100 gms) fabricated with mitered joints and applying PVC solvent cement and screwed with full body threaded star headed SS screws having min frame density of 750 Kg/cum screw withdrawl strength of 2200 N (face) & 1100N edge, minimum, compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of of flame of class ‘A’ category with property of being termite/borer proof, water/ moisture proof & fire retardant & fixed in position with SS dash fasterns/ hold fast of required dia and length, colour of door frame to match that of shutter all as specified and directed

-Blank-

M & L PCC 1:3:6 Type C 0 usind 12.5 mm graded stone aggregate for backing of door chawkhats complata all as specified and directed by Engr-in Charge

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed

M&L for Preparation of old steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint etc complete all as specified and as directed

M&L for complete removal of existing treatment from wall upto plaster surface by washing, rubbing down and stopping of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces finally rubbed and smooth with sand paper all as directed by Engr-in-charge.

M&L for applying two coats of acrylic distemper over a coat of primer, white or tinted over 0.75 to 1 mm thick putty in two coat over new/old plastered surface of walls. Complete all as specified & directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over 0.8 to 1.2 mm thick wall care putty . Complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks straight or curved on plan in CM 1:4 as in half brick thick walls complete all as specified and as directed

Demolition of cement concrete (reinforcement cut as required to facilitate demolition) of any description & in any position not specifically provided for complete all as specified and as directed

M&L for reinforced cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) (nominal mix) as in slabs supported on wall, landing, balconies, canopies, deck slabs and in shelves and like in repair to Chajjas, Claddings, soffits etc including bonding agent, complete all as specified and directed. Note:- Reinforcement to be measured & paid under respective items.

M&L for form work to chullah hoods, chajjas, troughs and similar items including edges for rough finished surfaces of concrete flat, complete all as specified and directed.

M & L for form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide for rough finished surfaces of concrete complete all as specified and directed.

M&L for TMT Bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete incl welding etc (if reqd) all as specified and directed.

--ditto-- as per item above but 6mm to 8mm.

Supply only liquid water proofing compound complete all as specified and directed.

Surface excavation n exc 30 cm deep and averaging 15 cm and getting out in any type of soil complete all as specified.

Removing excavation material surplus soil to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified & directed.

M&L heavy duty coloured parking tiles 10 to 12 mm thick dark shaded (Square / rectangular ), area of each tile not exceeding 0.36 sqm in floor etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade, incl 15 mm thick screed bed in cement mortar 1:4. Complete all as specified and as directed.

Excavation in trenches n exc 1.5m wide and n exc 1.50m in depth for foundation etc and getting out in soft/loose soil complete all as specified and directed by Engineer-In- Charge.

Returning filling in, incl spreading levelling watering and well ramming in layers n exc 25cm (after the pipes have been laid and tested) in soft/loose soil complete all as specified and directed by Engineer-In- Charge.

Removing excavated material exceeding 250M but not exc 500m and depositing where directed. Complete all as specified and directed by Engineer-In- Charge.

M&L for providing plain cement concrete 1:4:8 type D-1 (using 40mm graded stone aggregate) as in foundation and mass concrete complete all as specified and directed by Engr-In- Charge.

M&L for providing precast cement concrete coping with plain fair faces incl chamferes, weathering, throating etc type B0, 1:2:4 using 12.5mm graded stone aggregate and set in CM 1:4 complete all as specified and directed by Engineer-In- Charge.

M & L for cement concrete 1:3:6 type C-2 for 150 mm dia in concrete bed to drain pipes including packing under and haunching against the sides of pipes etc complete all as specified and directed by Engineer-In- Charge

M & L for reinforced concrete pipes,150mm dia class NP-2 laid and jointed complete with collars complete all as specified and directed by Engineer-In- Charge.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1 : 4 mixed with water proofing compound finished even and smooth without using extra cement complete all as specified and directed by Engineer-In- Charge. (Water proofing compound shall be measure and paid separatelly).

M&L for 15mm thick rendering on other than fair faces of brick work in CM 1 : 6 finished even and smooth without using extra cement complete all as specified and directed by Engineer-In- Charge.

Cutting into existing manholes for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 or 3/4 section ) in cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate finished smooth and reforming benching as required for 150mm dia pipes complete all as specified and directed by Engineer-In- Charge.

M&L for providing pre cast RCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in cover slab and man hole covers etc complete all as specified and directed by Engineer-In- Charge.

M/L PCC 1:3:6 type C0 ( using 12.5 mm thick graded stone aggragate) as in surface channel drain. Complete all as specified and directed

Desludging/desilting of 150 mm dia sewage lines including manholes, up to 2.0 m depth by removing blockage if any by means of rodding manually or mechanically by pumping out water where required and removing residual silt/mud/peat/sludge out side of defence land complete all as directed by Engr-in-charge. Note:The work has to be carried under foul condition, hence the rate to be deemed included.Nothing extra shall be paid to the contractor on this account

M&L PCC 1:2:4 type B-2 using 20mm graded stone aggregates as in foundation posts filling. complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:2:4 type B-0, using 12.5 mm graded stone aggregate as in coping bed blocks for angleand similar work incl necessary form work to obtain a smooth finishescomplete all as specified and directed by Engr-In- Charge.

M & L applying two coats of cement based paint over a coat of primer on new plastered surface incl preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

S&F mild steel angles, tees, flats, C section, MS square bars, MS Tubes etc as in steel gates, steel posts and struts in fencing, grills including embedding in concrete and screwing etc. including cut to shape as directed, drilling holes, notching for wire etc including all necessary drilling, bolting, welding or riveting and similar work conforming to FE-290 Gde E-165 complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Chain link MS Galvanised fencing any size or type complete all as specified and directed by Engineer-in-Charge

S & F 2 mm thick Fibre glass reinforced translucent corrugated/plain sheeting with two corrugations side lap fixed with coach screws and washers in roof, wall etc complete all as specified and directed by Engineer-in-Charge

-Blank-

Taking down carefully copper/Aluminum point wiring (light, fan socket and power) complete including switches, ceiling rose lamp holder and regulator etc and removing from site and making good disturbed surfaces of walls/floors etc complete all as specified and directed by Eng-in-charge Note: old point wiring obtained fro Sl item no 131 to 132 of Sch A.

M&Lin replacement point wiring with 1.5 Sqmm (nominal area) two single core PVC insulated unsheathed multi stranded copper conductor cable 1100 volts grade, FRLS-H grade including concealed PVC conduit 20 mm dia or higher and conduit fittings and all accessories with suitable size of metal flush box and metal frame, for mounting of Modular switches, sockets, fan regulator etc with modular white cover plate as top cover, including contineous earth wire PVC insulated, unsheathed, multi stranded copper conductor cable 1.5 sqmm (nominal area) FRLS-H grade, green colour, up to common earth and connected to earth dolly compete all as specified and directed by Eng.-in-charge of the following. Note: (a) Colour code shall be maintained as per IE rule. .

(a) One light point /bell buzzer point controlled by one,one way switch.

(b) One ceiling fan/Exhaust fan point controlled by one,one way switch through Regulator.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One three pin 5 Amp socket on independent board

All as per item No 131 above but one 3 pin socket outlet 15 Amp independent, with cable 2.5 Sq mm size, with earth continuity coductor of size 2.5 Sq mm.

M&L for new point wiring with 1.5 Sqmm (nominal area) two single core PVC insulated unsheathed multi stranded copper conductor cable 1100 volts grade, FRLS-H grade in and including medium duty concealed PVC conduit 20 mm dia or higher and conduit fittings with cutting chases and all accessories with suitable size of metal flush box and metal frame, for mounting of Modular switches, sockets, fan regulator etc with modular white cover plate as top cover, including contineous earth wire PVC insulated, unsheathed, multi stranded copper conductor cable 1.5 sqmm (nominal area) FRLS-H grade, green colour, up to common earth and connected to earth dolly compete all as specified and directed by Eng.-in-charge of the following. Note: (a) Colour code shall be maintained as per IE rule

(a) One light point /bell buzzer point controlled by one,one way switch.

(b) One ceiling fan/Exhaust fan point controlled by one,one way switch through Regulator.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One three pin 5 Amp socket on independent board

All as per item No 4(d) above but one 3 pin socket outlet 15 Amp independent, with cable 2.5 Sq mm size, with earth continuity coductor of size 2.5 Sq mm.

S&F Modular switch 1 way 6A,1 Module SP 230 V AC complete all as specified & directed.

S&F Modular switch 1 way 16A,1 Module SP 230 V AC complete all as specified & directed.

S&F Modular Socket,6A-2/3 pin combined,2 Module 230 V AC complete all as specified & directed.

S&F Modular socket outlet two in one three pin 5 Amp and 15 Amp flush type complete al as specified.

S&F Modular Bell switch 6 Amp,1 Module complete all as specified.

S&F ding dong bell AC 230 V single pole complete all as specified and directed .

S&F modular fan step type electronic fan regulator two module 120 Watt as required.

S&F ceiling rose, 3 terminal/PVC/polycarbonate, isolated body 230 V AC.

S&F lamp holder PVC/polycarbonate type with back plate suitable for batten fittings.230 V AC.

M&L in replacement sub main wiring with 2 Single core PVC insulated unsheathed FRLS-H cable 1100 Volts grade heavy duty copper conductor multistranded of size 6 Sq.mm. (nominal area) drawing in and including 20 mm. dia or higher PVC conduit medium duty concealed, conduit heavy duty accessories and fittings with chasing/ cutting and Insulated unsheathed FRLS-H cable copper conductor multistranded of size 6.0 Sq. mm. as earth wire upto common earth and connected to earth dolly complete all as specified & directed including taking down old sub main wiring .

Supply,fixing and Testing TP & N Vertical load line (VTPN) 4 way 415 Volts 50 Hz indoor type double door sheet metal enclosure IP-43 DB's IK-09 flush mounted with 250 Amp Copper busbar for each phase with neutral bar & earthbar and cable ties for cable management including Provision of MCCB 63 Amps,ICs=100%ICu, 16KA four pole as in comer including connecting terminal strip complete and SP MCBs as out going etc complete pre wired with suitable size copper conductor. The DB's shall hold type test certificate (CPRI) as per IEC 61439-3 complete all as specified and directed by Eng-in-charge including taking out old unserviceable DB and removing from site. (Note :- MCB/ MCCB shall be measured and paid separately)

S&F in replacement sheet metal enclosures 240 volt with 200 amps rated copper bus bar for double door 8 way IP-43DB's lk-09suitable for one MCB SPN as incoming and 6 MCB SP as out going, mounting flush on wall and making good disturbed surfaces complete all as specified and directed by Engr-in-charge ,including taking down old unserviceable DBs . (MCBs shall be measured and paid separately).

S&F MCB double pole 240 Volt 10 KA 40-63 Amp 'C' series conforming to ISI marked complete all as specified & directed .

S&F MCB single pole and 240 volt 10 KA 5-32 Amp 'C' series conforming to ISI marked all as specified and directed .

S&F MCCB 415 Volt 16 KA 4 pole 63 Amp magnetic trip release & setting as incoming with fixing arrangement complete all as specified and directed.

Supply & fix in replacement LED light fitting 1x20 W,220V AC decorative box type holder including LED tube light with driver connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply & fix new LED light fitting 1x20 W,220V AC decorative box type holder including LED tube light with driver ,connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

S&F LED light fitting mirror type with high out put diffuser 2 feet ,10 watt 220V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

S&F LED light fitting decorative wall mounting cast aluminium Polycarbonate paint bracket suitable for 5 watts LED bulbwith frosted glass with and including One No 5 watt LED lamp. complete with accessories and including connecting up with twin core twisted flexible copper conductor cable of suitable size.

S & F high efficiency LED bulbs 1 X 12 watt that can be used as a ready replacement for existing GLS ad CFL direct fit in holder complete all as specified and directed.

S&F ceiling fans complete with blades ,down rods and accessories ,230 V ,1200mm sweep.Min air delivery 210 CFM with service value 6.00 BEE Five Star Rated with Brushless Direct Current(BLDC) Motor. Note:(1)Rate for hanging arrangements of Ceiling Fan deemed to be included.

Supply and fix water heater ,storage type steel body with metallic inner tank and heating element upto 2 KW capacity 25 litre,BEE 5 Star rated complete with all accessories such as safety valve ,thermostate ,NRV,steel braided connection pipe 450 mm long complete all as specified and directed by engineer in charge.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm all as specified and directed.

M&L for earthing complete with using galvanized mild steel earth plate (electrode) 600 mm x 600 mmx 6 mm thick buried directly in ground, earth pit not less than 2.25 mtr deep below ground level with top edge of the earth plate not less than 1.50 m below ground level and earth plate surrounded with adequate quantity of charcoal dust mixed with salt to be packed thickness of 15 cm all round the plate using 4 mm dia GI earth lead wire as earth lead moulded and rivetted to earth plate at one end and connected to main equipment at switch/control board at another end, GI earth lead protected in and including 15 mm dia GI ‘medium grade’ pipe from upper end of earth plate upto equipment with & including 20 mm dia bore GI pipe ‘medium grade’ as water pipe from earth chamber to upper edge of the earth plate, GI funnel with wire mesh fixed on water pipe and provision of PCC 1:2:4 type B1(using 20 mm graded stone agg) as in pits chamber and RCC pit cover 50 mm thick of precast RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as per electrical plate No.3 of SSR Part-II 2010 and testing on completion all as specified and directed.

Supply and Fixing Integral LED Street Light Luminaire comprising of high pressure die cast aluminum housing heat resistant toughened glass with frame IP-65 protection road way luminaries with high power LED 40/45 watt with efficiency 100 lumen/watt at system level, CCT>5700K, with average life class 50,000 burning hours including GI brackete made out of 25 mm GI pipe medium grade and MS clamps for fixing of light fitting complete and connected with twin core PVC insulated copper flexible cable with existing point all as specified and directed

Supplying, laying in replacement, jointing and testing LT underground cable of size 16 sqmm4 coreheavy duty, 1100 Volts, PVC insulated and sheathed, armoured with multi-stranded aluminium conductor cable conforming to latest IS , laid in trenches/ducts or fixed to poles/walls or laid under roads/paths/drains/culverts duly protected in galvanised steel pipe of suitable sizes all bare conductor of cable duly insulated 1.1 KV grade heat shrinkable sleeve including cable gland and lugging etc at both ends all complete all as specified and directed. Note : Excavation, earth work, cable sand cushioning & cable protection shall be measured separately under relevant items of this schedule.

Supplying, laying , jointing and testing LT underground cable of size 25 sqmm 4 core heavy duty, 1100 Volts, PVC insulated and sheathed, armoured with multi-stranded aluminium conductor cable conforming to latest IS , laid in trenches/ducts or fixed to poles/walls or laid under roads/paths/drains/culverts duly protected in galvanised steel pipe of suitable sizes all bare conductor of cable duly insulated 1.1 KV grade heat shrinkable sleeve including cable gland and lugging etc at both ends all complete all as specified and directed. Note : Excavation, earth work, cable sand cushioning & cable protection shall be measured separately under relevant items of this schedule.

M&L sub main wiring with 2 Single core PVC insulated unsheathed FRLS-H cable 1100 Volts grade heavy duty copper conductor multistranded of size 2.5 Sqmm. (nominal area) drawing in and including 20 mm dia or higher PVC conduit medium duty concealed, conduit heavy duty accessories and fittings with chasing/ cutting and insulated unsheathed FRLS-H cable copper conductor multistranded of size 2.5 Sqmm as earth wire upto common earth and connected to earth dolly completed all as specified & directed including taking down old sub main wiring.

M&L for laying local dry clean sand filling for cushioning in trenches around under ground cable complete all as specified and directed.

M&L for laying well burnt brick, old size in trenches, as protection of under ground cable complete all as specified and directed.

S&F LED light fitting 1x9W/1x10W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete.

Taking down and refixing energy meter fixed in walls/panels of any capacity/any type after carefully disconnecting electrical connections all as specified and directed by Eng-in-charge. Note:- Quoted rate shall deemed to be inclusive of following parameters:- (a) Meter reading shall record shall be submitted before and after replacement duly signed by the contractor rep and MES rep. (b) Old meter should be handed over to MES rep/or in written custody of the Contractor. (c) Any rejoining wires/cables shall be done using suitable ferrule/cable connectors after removal of meter.

Supply and laying replacement pipe galvanized, “Medium class”, including fittings 40 mm dia complete all as specified and directed by engineer in charge.

Supply and laying replacement pipe galvanized, “Medium class”, including fittings 25 mm dia complete all as specified and directed by engineer in charge.

S&F gun metal gate valve heavy duly ISI marked with iron wheel head, screwed both ends for iron pipe of size 40 mm complete all as specified and directed.

S&F gun metal gate valve heavy duly ISI marked with iron wheel head, screwed both ends for iron pipe of size 25 mm complete all as specified and directed.

Drilling and tapping CI/DI water mains(in position) for branch connections of 15mm internal dia.

M&L for Machine pressed precast concrete interlocking paver block any shape and size conforming to IS 15658-2006 of 60 mm thickness, M-35 Grade, set and jointed in grey cement and pigment, incl sand cushioning 40 mm thick. Complete all as specified and directed by Engr-In-Charge.

sath sahib associates (BID ID -3163958)

AYUSH CONSTRUCTION COMPANY (BID ID -3167345)

PAWAN KUMAR (BID ID -3167103)

Ms dev associates (BID ID -3166867)