REPAIR TO ROADS, BERMS, ROAD FURNITURE AND CONNECTED WORKS IN THE AREA OF AGE B/R-II UNDER GE (NORTH) AMBALA CANTT

Amount

Material and labour for repair to pot holes of any depth, exceeding 1.00 Sqm each, including sweeping free from dust and mud or water, scoring sunken surfaces in roads/ path etc, cutting around edges to at least 25mm and more as per site requirement in depth and making good by applying tack coat of paving bitumen @ of 5 Kg per 10 Sqm, putting in premixed bituminous macadam, well rammed and sealed with binder 9.8 Kg per 10 Sqm, blinded with 0.09 cum of stone chippings 6.3mm size and again well rammed (including supply of premixed macadam binder and chippings) for depth of pot holes exceeding 30mm complete all as specified and directed..

Material and labour for preparation of black top bituminous surface by brushing with wire brushes for removing caked mud etc. sweeping with brooms and finally fanning the cleaned surfaces with air compressor to remove all loose dirt etc and applying evenly a bituminous tack coat of paving bitumen of Grade VG-10 @ of 2.5 Kg per 10 sqm complete all as specified and as directed.

Material and labour for premixed, bituminous macadam using 4% binder content of paving bitumen of grade VG-30, by weight of total mix, rolled and compacted with 8 to 12 tonne power road roller to required gradient and camber using full width mechanical sensor paver with string sensor (consolidated thickness not exceeding 75 mm) complete all as specified and directed. Note: (i) The quoted rate shall deem to include for preparation of level sheets by contractor before laying DAC over BM as directed at site. (ii) A recovery @ Rs 52.00 per kg shall be made if the bitumen content in design mix is found on lower side but no adjustment shall be made if the bitumen content is found on higher side than specified.

Material and labour for Bituminious premix dense asphaltic concrete 30mm thick (consolidated thickness), pre-mixed, hot mix, with coarse aggregate of grading 1 as per MORT&H specification in single layer using paving bitumen (grade VG-30) @ 6% by weight of the total mix as per design mix including supply and mixing of filler (OPC cement) laid, rolled and compacted to required gradient and camber using full width mechanical sensor paver with string sensor and compacted with 8 to12 tonne power vibratory road roller including taking down of existing cat eyes and refixing of cat eyes after laying premix complete all as specified and directed. Note- (i) Bituminous premix dense asphaltic concrete shall prepared in central computerised hot mix plant. complete all as specified and as directed. (ii) Design mix shall be got done by the contractor at his own expenses from laboratory as decided by GE, before laying the DAC. (iii) A recovery @ Rs 52.00 per kg shall be made if the bitumen content in design mix is found on lower side but no adjustment shall be made if the bitumen content is found on higher side than specified. Material and labour for laying bituminous premix semi dense asphaltic concrete 30mm (consolidated thickness) using with 5.5% of binder (grade VG-30) content by weight of total mix, rolled and compacted to required camber and gradient using mechanical paver and rolled with 10-12 tonne capacity vibratory road roller rolled to uniform smooth surface ,complete all as specified and as directed.

Material and labour for preparation of new or existing black top surfaces, removing dust, dirt, grease & other foreign matters etc. to receive the marking and applying hot applied thermoplastic road marking paint (white/yellow) conforming to BS-3262-1989 inclusive type I reflectorising glass beads as per table 800-3, 800-4 of MORT&H applied in uniform thickness of at least 2.00mm and 10cm wide and spread uniformly with reflectorising glass beads type I & II as per Clause 803.4.3 of MORT&H specifications with a road marking machine as per IRC: 35 ,with traffic diversion arrangements if required, complete as per MORT&H specification clause 803.4, complete all as specified and directed. Note: The road marking machine shall be approved by GE.

Supply and fixing in replacement cat eye solar reflective type of ABS body of size 100mm x 100mm x 18.5mm, two way reflective (reflective panel-Amber, Red or White) fixed with and including MS stud of suitable size and epoxy as per manufactures instructions complete all as specified and directed. Make- Model No DA 978 of Dark Eye or equivalent of makes as specified in tender documents.

Supply and fixing in replacement solar cat eye aluminum alloy (100% water proofing design according to IP65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono-Crystalline solar panel 2.4V/ 0.3 watt one Ni-Cd rechargeable battery (1.2V/1600MA) consisting of super bright LED with 10,000 to 18,000 mcd (Millicandela) complete as per manufactures instructions ,working time: 3 to 4 days after fully charged battery, view Distance: upto 1000 meters, colour as directed, bearable weight: 10 tonne approx complete all as specified and as directed. Make- Model No DA 110 Dhruv of Dark Eye or equivalent of makes as specified in tender documents.

Note:- Amount of credit of Rs. 1715.00 for retrieved materials is mentioned in Schedule of Credit Page No. 17 of tender documents in pdf form which will be deducted offline while acceptance of tender.

shree balaji builders

M/s DATAAR BUILDERS