SPECIAL REPAIR TO BLDG NOS P-6/1 AND P-6/2 OF BENGAL BN NCC, BURDWAN AND OTHER SANCTIONED WORKS IN THE AREA OF AGE B/R I UNDER GE PANAGARH

Amount

M&L for Excavating in post holes (or similar holes) each n exc 0.5 cu. m and getting out in soft/dense soil including removing of excavated materials to a distance n. exc 50m and depositing where directed at a level n exc 1.5m above the starting point in oft/loose soil complete all as specified and directed.

Excavating in trenches , n.exc 1.5 m wide and n.exc 1.5 m depth for foundation etc or for shafts, wells, cesspits ,manhole pier hole etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in in soft/loose soil Note : Manual excavation to be done. During excavation if any damage occured to existing cable any type/ water pipe line, it will be contractor responsibilty to get it repair and make functional by providing jointing kit etc without any extra cost. Contractor has to repair it within 24 hrs so that essential service can not be effected due to such damage.If contractor fails to repair it within 24 hrs penalty @ Rs 500/- will be charged to contractor. In this GE decision will be final, conclusive and binding.

All as per BOQ Item No 2.00 here-in-above but exc 1.5 m depth upto 3.00m complete all as specified and directed.

All as per BOQ Item No 2.00 here-in-above but as in hard/dense soil

Excavation over areas, n exc 1.5 m deep and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in and including spreading, leveling, watering & well ramming in layers n.exceeding 25 cm in soft/loose soil complete all as specified and directed.

Removing of excavated materials to a distance n. exc 50m and depositing where directed at a level n exc 1.5m above the starting point in oft/loose soil complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15 cm deep and getting out in soft and loose soil complete all as specified and directed.

M&L for Hardcore using broken stone or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for Moorum/red bajri filling in floors or in foundation, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed

M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L for Cement concrete type (C-2) 1:3:6 (using 40mm grded stone aggregate) as in foundations, filling and mass concrete and as in post holes complete all as specified and directed.

M&L for PCC(1:2:4) type B-0 (using 20mm graded aggregate) as in roof kerbs or mud stop rounded complete all as specified and directed.

M&L for PCC type D2, 1:4:8 (using 40mm graded aggregate) in foundations, filling and mass concrete complete all as specified and directed.

M&L for type B-1 1:2:4 (using 20mm graded stone aggregate) providing RCC precast cement concrete as in cover slab for man hole and similar article with plain face set in cement mortar (1:6) complete all as specified and directed.

M&L for reinforced cement concrete(Nominal Mix) type B-0 (1:2:4) using 12.5 mm graded aggregate as in chajjas and similar work like slab supprted on walls etc complete all as specified & directed by Engineer in Charge.

M&L for cement concrete type C-1 1:3:6 (using 20mm graded stone aggregate) in cills, steps, plinth courses, string courses, lacing courses, parapets, copings, kneelers, apex stones, bed plates, kerbs water troughs and the like including weathering, slightly rounded for chamfered angles and throating, as directed rounded or chamfered on edges complete all as specified and directed

M&L for PCC type B2 1:2:4 (using 40 mm graded aggregates) as in foundations, fillings and mass concrete complete all as specified and as directed

M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

M&L for RCC M-25 (Design Mix) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

Supply only Integral Liquid water proofing compound complete all as specified and directed

M&L for Use and Waste of Formwork (steel plate stiffened with steel angles, steel pipe scaffolding telescopic or otherwise) to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, rough finished surfaces of concrete, flat

Dismantling/taking down old existing unserviceable cement plaster loose/unsound weaken cement concrete incl demolition of any description and in any position from existing external/internal surfaces of RCC roof slab etc, (upto maximum height of 10 metres from natural ground level) with power driven pneumatic chisel and including removal of debris and washing down with water to remove dust, foreign items complete all as specified and directedcomplete all as specified and directed

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlar facings, dressedstonework and precastconcrete articles

Demolition of cement concrete (un-reinforced) not exceeding 15 cm thickness (above or below ground level) and removing rubbish off from site complete all as specified and directed.

Demolition of RCC cement concrete (reinforcement cut as required to facilitate demolition) all as directed by Engineer-in-Charge

M&L for 25 mm thick average PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in padding concrete on roof all as directed by Engr-in-Charge.

M&L for rendering 15mm thick on fair faces on roof surfaces of concrete in Cement Mortar (1:4) finished even and smooth without using extra cement and WPC complete all as specified and directed. Note :- WPC will measuered and paid separatly under relevant item of schedule.

M&L for preparation of new surfaces of roof and applying two coats of Polyurethane(PU) accrylic based waater proofing liquied compound over and including one coat of self priming primer @ one litre per 10 sqm with reiforcing fabricc sheet as per manufacturer's instructions to stop leakage/seepage from roof/wall complete all as specified and as directed by the Engr-in-Charge. Note : As per description of this item, minimum two cots of Polyurethane (PU) acrylic based wate proofing liquid compound over one coat of primer shall be carried out as per manufacturer's instruction. Please note no price adjustment shall be made, if as per manufacturer's instrucions more coats of Polyerethane (PU) acrylic based waterr proofing liquid compound and primer are required for roof treatment. (ii) Quoted rate shall be included for work in building/struture of any height. (iii) To be applied by uthorised applicator.

S&F mild steel as in post, trusses, purlin, crane rail and joist, channel angle or tee sections including all necessary cutting welding etc complete conforming to FE 410 W( Gde-E-250) quality A all as specified and directed.

M&L for pre-painted hot-dip aluminium-zinc alloy metallic coated of any profile steel sheet corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified up to 18 Mtr height including all necessary scaffolding and safety measures complete all as specified and directed

M&L for pre-painted hot-dip aluminium-zinc alloy metallic coated plain steel sheet as in ridges, roof covering/cladding to wall, corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified up to 18 Mtr height including all necessary scaffolding and safety measures complete all as specified and directed

S&F wind ties for roof including securing bolts, flat iron fillets(for securing weather boarding with screw bolts and nuts) including all necessary drilling or riveting etc and similar work conforming to Fe 410-O or Fe-310-O including painted with one soap coat of zinc cromate primer paint (including preparation of surfaces at contractor's workshop before fabrication) complete all as specified and directed

S&F Steel windows with side hung shutters (minimum wt. of steel section should be 1.42 kg/M) including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, including making good disturbed surfaces as per existing specfication complete all as specified and directed.

S&F steel ventilator with top hung shutter (minimum wt. of steel section should be 1.42 kg/M) including hinges, steel peg stay, complete with glazing bars, dovetailed or welded, including making good disturbed surfaces as per existing specfication complete all as specified and directed.

M&L for framed work such as grills etc with ends of bars shouldered and or riveted or forged into spike, framed guard bars and similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed.

S&F Mild Steel TMT bars 10mm and over, cut to lenghth, bent to shape requird, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clip all as directed by Engineer in Charge.

All as per item no 37.00 herein before but 6 to 8mm dia complete all as specified & directed by Engineer in Charge

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc of Fe 410 -W (GdeE- 250) quality A complete all as specified and directed.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment using Fe 410 -W (Gde E- 250) quality A, complete all as specified and directed.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screw other .and each screw end to be fixed with washers and nut exc 5 cm but n.exc 10 cm long complete all as specified and directed

M&L for two coats synthetic enamel paint over a coat of red oxide primer on new steel surfaces incl preparation of surfaces over 10 cm width or girth complete all as specified and directed.

M&L for two coats synthtic enamel paint on old steel surfaces incl preparation of surfaces over 10 cm width or girth complete all as specified and directed.

Taking up or down 15mm dia bore steel tubing and connection including cleaning for refixing or remove to store complete all as specified and directed.

S&F 15 mm dia bore steel tubing medium grade galvanised with all fittings and connection complete all as specified and directed.

Taking up or down 20mm dia bore steel tubing and connection including cleaning for refixing or remove to store complete all as specified and directed.

S&F GI 20 mm dia bore steel tubing medium grade galvanised with all fittings & connection complete all as specified and directed.

S&F ISI marked rotational moulded polyethylene multi- layer water tanks (vertical cylindrical with close top) of 500 litres capacity hoisted and fixed in position including provision of 20 mm /15 mm dia medium grade GI pipe for connecting inlet, outlet, over flow and washout pipes including dismantling the existing one and removing to store complete all as specified and as directed.

S&F in repair for Gun metal gate valve,15 mm bore, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

All as per item No 49.00 above but 20mm dia complete all as specified and directed.

Taking down rain water pipes (any size or pattern) , including all fittings and removal off the site complete all as specified and directed.

S&F PVC SWR pipes 110 mm bore single socketed in any length with rubber ring joint fixed to wall with steel clamps all as specified and directed .

M&L for fixing PVC (SWR) pipes of 100 mm bore diameter single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed

S&F PVC SWR bends of 110 mm bore complete all as specified and directed.

S&F PVC (SWR) junction single (single T) equal or unequal provided with access door of 110 mm dia complete all as specified and directed.

S&F in repairs water closet Vitreous china squatting pan Orissa pattern of size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, antisyphonage connection pipe etc complete making good disturb surface with existing finish of floor all as specified & directed by Engr-in-Charge.

S&F Vitreous china wash down water closet pan, pedestal pattern Pedestal pan and trap(excluding flushing cistern and flush pipe),connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc and including plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel CP or aluminised hinging device complete all as specified and directed.

S&F in repairs 10 Litre capacity PVC valveless, syphonicaction type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed by Engr-in-Charge.

S&F in repair bib taps of 15mm bore fancy type, chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs 15mm bib tap PTMT any colour screwed for iron pipe complete all as specified and directed by Engr-in-Charge.

S&F 15mm bore dia brass CP mixer for mixing hot &cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F in repair 15 mm bore stop valve cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe of for unions complete all as specified and directed.

S&F in repair PVC connection 15 mm size PTMT nuts of length length 600 mm complete all as specified and directed

S&F Stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers, waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repair stainless steel kitchen plate rack made out of 0.65mm thick of approved make with plugs, washers, over all size 786mmx610mmx 254mm of make Prayag Cat No P-440 complete all as specified and directed.

S&F in repairs vitreous china wash basin, white, flat back, size, 550X400mm including bracket for fixing 32 mm waste coupling, waste pipe etc complete all as specified and directed.

S&F in repairs Pillar taps, 15mm bore, fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'HOT or COLD' with long screwed shanks and fly-nuts, screwed for iron pipe or for connection pipe complete all as specified and directed.

S&F in repair PVC waste pipe 32mm dia for wash basin and sink 01 mtr long complete all as specified and directed

S&F in repair soap dish vitreous china white size 160x160x90mm approx all as directed by Engineer-in-Charge

Supply only Flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern etc complete all as specified and directed

S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete complete all as specified and directed

M&L for Cast iron floor trap 75mm dia, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete fixed in position complete all as specified and directed

M&L for Cast iron nahani trap 100mm dia, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete fixed in position complete all as specified and directed

M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete, all as specified and as directed.

M&L for brick work with flyash bricks straight or corve on plan to any radius in half bricks thick walls, built in cement mortar (1:4) complete all as specified and directed.

Taking down cement plaster of any description on concrete surfaces such as soffit of RCC slab, chajjas, ceiling and brick walls etc incl raking out joints, hecking for key scrubbing down with water and removal of rubbish off the premises complete all as specified and directed

M&L for Rendering 15mm thick in CM (1:6) on fair faces of brick work or concrete surfaces of wall finsihed even and smooth with out using extra cement complete all as specified and directed

M&L for Rendering 15mm thick in CM (1:4) using liquid waterproofing compound as per manufacturer instruction on fair faces of brick work or concrete surfaces of wall finished even and smooth without using extra cement complete all as specified and directed Note : WPC shall be measured and paid separately.

M&L for Rendering 5mm thick in CM (1:3) on fair faces of brick work or concrete surfaces of ceiling finsihed even and smooth with out using extra cement complete all as specified and directed.

Taking down chowkhat or frame with shutters n.exe 1.50 Sqm (without taking of shutter from frame) each complete all as specified and directed

Taking down chowkhat or frame with shutters exe 1.50 Sqm and not 4 sqm (without taking of shutter from frame) each complete all as specified and directed

S&F factory made solid PVC door frame of size 50mmx47mm made out of 5 mm plain colour PVC sheet with mild steel square tube complete as per manufacturer specification & drawing complete all as specified and directed by Engr-in-Charge.

S&F factory made solid panel PVC door shutter 30 mm thick (stiles) consisting of frame made out of mild steel tubes for top & bottom rails. Mild steel frame shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20 mm with stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap inserted for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the mild steel frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement fixing in the frame at site as per specification, drawing complete all as specified and directed by Engr-in-Charge.

S&F 35mm thick factory made 2nd class hardwood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed by Engr-in-Charge .

S&F Factory made single extruded WPC (Wood polymer composite) solid door/window and others frames/chowkhat of size 50x125 mm double shutter comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres and non toxic additives fabricated with mitred joints after applying PVC solvent cement and screwed with full body threaded star headed SS Screws having minimum frame density of 750kg/cum and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engr-in-charge.

S&F Factory made single extruded WPC (Wood polymer composite) solid Plain flush door shutter of 30 mm size comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres and non toxic additives having minimum density of 650kg/cum and with property of being termite/ borerproof, water/ moisture proof and fire retardent and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws complete as per direction of Engr-in-charge.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engr-in-Charge

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engr-in-charge.

M&L for sheet glass 4mm thick ordinary quality and glazing with oil putty and pin in square n. exc 0.50 sqm in each pane frosted one side complete all as specified and directed.

M&L for 4mm thick figured glass, pin head type and glazing with oil putty or with brass screws in square n.exc 0.50 sqm in each pan for bathrooms/toilets ventilators complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long or corner type dia 12 cm complete all as specified and directed.

S&F in repair of PVC Mirror cabinet, size 330x430 mm single door with mirror colour white complete all as specified and directed make as given inlist of makes as directed by Engr-in-charge

M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregate as in concrete bed to drain pipes of 150 mm bore including cradle after they are laid and tested; including necessary form work complete all as specified and as directed.

M&L for 150mm bore, HDPE double wall corrugated(DWC) SN-8 PIPE (HDPE Black Pipe) WITH COUPLER Conforming to IS:16098 Part-II:2013 sewage pipes laid in trenches and jointed as per manufacturer,s instruction with and including all fitting complete all as specified and as directed.

S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, Width of flaps (when open) in 30mm complete all as specified and directed.

S&F door closer aluminium body, hydraulically regulated, designation No.2, universal type, suitable for door shutters and weight between 36 to 60 kg and fixed complete all as specified and directed.

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor of Overall length of cover plate complete all as specified and directed.

S&F mild steel ordinary rat tail rod pattern spring 150mm including roller and roller plate on wooden/steel choukhat including welding, riveting etc complete all as specified and directed by Engr-in-Charge.

S&F stainless steel Butt hinges100mm long medium weight, cold rolled complete all as specified and directed.

S&F 75mm long butt hinges, extruded alluminium alloy/stain less steel with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed.

S&F aluminium anodised 150 mm barrel tower bolts of extruded section complete all as specified and directed.

S&F aluminium anodised 75 mm barrel tower bolts of extruded section complete all as specified and directed.

S&F 150 mm long aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 75 mm long aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and dirceted.

S&F stainless steel wire cloth of 0.36 mm nominal dia of wire and averaging of width of aperture 1.40mm, fixed with stainless steel wire staples complete all as specified and directed.

S&F in repairs harrison rails/ curtain rails, anodised aluminium alloy chromium plated with fixing brackets, stops, rollers/globe etc complete all as specfied and directed.

M&L for painting on new wooden based surfaces of any description not other wise described over 10cm width or girth applying two coat synthetic enamel paint over one coat of pink primer including preparation of surfaces complete all as specified and directed by Engr-in-Charge .

M&L for preparation of old painted of wood and wooden based materials surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for removing of cavities by roughening the smooth ceiling surface scrapping out/removing corrosion all loose/sclae/rust etc from the visible reinforcment by applying rust remover @20ml per Sqm or as per manufacturer's instructions, rust removal and cleaning steel reinforcement proeprly and then apply 40 micron thick dry thickness coat of epoxy zinc primer @250 ml per Sqm or as per manufacturer's instructions of exposed and new steel reinforcemnt (measured flat) complete all as specified and directed.

M&L for preparation of new surfaces of plastered walls and applying two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour over and including a coat of primer over and including wall care putty (1.0 mm thick) complete at any height including all necessary scaffolding and safety measures complete all as specified and directed.

M&L for preparation of new surfaces of plastered ceiing and applying two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour over and including a coat of primer over and including wall care putty (1.0 mm thick) complete at any height including all necessary scaffolding and safety measures complete all as specified and directed.

M&L for preparation of surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing to low lying area and rubbish off the premises complete all as specified and directed.

M&L for 25mm thick Cement concrete type B-0, 1:2:4 (using 12.5mm graded stone aggregate) as in floor for levelling course complete all as specified and directed by Engr-in-Charge.

M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles over and including 10mm thick rendering in cement mortar (1:3) complete all as specified and directed. Note: Design, shade and pattern of fixing of tiles shall be as directed and approved by GE

M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tiles exc. 0.06 sqm but n. exc 0.11 sqm of approved colour as in floors etc set and joined in neat cement slurry over 15mm thick sreed bed of cement mortar (1:4) complete all as specified and directed. Note: Design, shade and pattern of fixing of tiles shall be as directed and approved by GE

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tiles exc. 0.11 sqm but n.exc 0.18 sqm of approved colour as in floors etc set and joined in neat cement slurry and pointed in white of coloured cement over and including 15mm thick screed bed of cement mortar (1:4) complete all as specified and directed by Engr-in-Charge. Note: Design, shade and pattern of fixing of tiles shall be as directed and approved by GE

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tiles exc. 0.11 sqm but n.exc 0.18 sqm of approved colour as in skirting etc set and joined in neat cement slurry and pointed in white of coloured cement over and including 10mm thick rendering in CM (1:4) complete all as specified and directed by Engr-in-Charge. Note: Design, shade and pattern of fixing of tiles shall be as directed and approved by GE

M&L for 8 to 9mm thick Vitrified Ceramic light shade tiles (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white of coloured cement to match over and including 15mm thick screed bed of cement mortar (1:4) complete all as specified and directed. Note: Design, shade and pattern of fixing of tiles shall be as directed and approved by GE

M&L for 8 to 9mm thick Vitrified Ceramic light shade tiles (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, as in skirting etc set and joined in neat cement slurry and pointed in white of coloured cement over and including 10mm thick rendering in CM (1:4) complete all as specified and directed by Engineer-in-Charge. Note: Design, shade and pattern of fixing of tiles shall be as directed and approved by GE

M&L for Green Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade inclusing 15mm thick screed bed in CM (1:4) complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade with grey cement and pigment complete all as specified and directed.

M&L for 75mm thick Cement concrete type C-1, 1:3:6 (using 20mm graded stone aggregate) as in plinth protection, path or in sub base of floors etc and channels etc Finished even and smooth without using extra cement complete all as specified and directed

M&L for 100mm thick Cement concrete type B-2, 1:2:4 (using 40mm graded stone aggregate) as in base of floor complete all as specified and directed.

M&L for 100 mm thick Cement concrete type D-2, 1:4:8 (using 40mm graded aggregate) as in sub base, sub floors etc complete all as specified and as directed

M&L for 50 mm thick Cement concrete type C- 2, 1:3:6 (using 40 mm graded aggregate) laid over cement concrete subfloors and finished to an even and rough surface, complete all as specified and as directed by Engr-in-charge.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M- 35 Grade with grey cement and pigments complete all as specified and as directed

M&L for cement concrete 75mm thick 1:2:4, Type B2 (Using 40 mm graded stone aggregates) as in floor finishing cement concrete surface and finishing the surface smooth and even without using extra cement complete all as specified and directed.

S&F 18/19 mm thick, prelaminated PVC moulded, solid cupboard cabinet shutter full size fitted to cupboards including hinges as required, 2 Nos handles (50mm to 65mm) and S&F 2 Nos ball catches 140mm with 8mm dia steel ball and brass body and striking plate as specified and directed by Engr-in-charge

S&F 18/19 mm thick, prelaminated PVC moulded solid shelves and drawers boxes fitted under cooking platform and other platfors including 2 Nos telescopic channel, 1 No handles (50mm to 65mm) and fixing as specxified and directed by Engr-in-Charge

E/M PORTION Taking down carefully copper/aluminium conductor point wiring (light, fan, socket or power) complete including fittings such as switches,ceiling roses, pendants, regulators ,sockets etc. and removing (except those to be reused shall be kept in safe custody at the site ) and making good disturbed surfaces of walls, floors etc.to match with the existing complete all as specified and directed.

M&L for concealed point wiring for fan/light point controlled by one way switch complete with 1.5 sq mm FRLSH,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red/yellow/blue wires for phases and black wire for neutral),drawn into and including non metalic PVC rigid conduit medium grade of suitable size and conduit accessories fixed on wall, floor, roof etc. and including provision of PVC FRLSH insulated 1.5 sq mm copper conductor for earth continuity (Green Colour) and connected to common earth dolly including sunken in GI terminal box 2.8 mm thick bakelite hylam sheet cover, ISI marked with CM/L no. for mounting switch & sockets for the following:- Note :- Cost of PVC conduit, cutting chases of wal/ceilingl, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

All as per Item No 135.00 here-in-before but with FRLSH grade, (ISI mark) PVC insulated and unsheathed two run multistranded copper conductor of size 2.5 Sqmm for one socket point of 3 pin 5 Amps on independent board including FRLSH grade (ISI mark), PVC insulated, unsheathed one run multi-stranded copper conductor of size 2.5 sqmm green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed.

All as per item No 135.00 above but 5 Amp socket on same board with other switches complete all as specified and directed.

All as per Item No. 135.00 here-in-before but with FRLSH grade, (ISI mark) PVC insulated and unsheathed two run multistranded copper conductor of size 4.0 Sqmm for one power point of 3 pin 15 Amps on independent board including FRLSH grade (ISI mark), PVC insulated, unsheathed one run multi-stranded copper conductor of size 4.0 sqmm green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed.

M&L for light/fan/exhaust fan point wiring controlled by one way switch complete with 1.5 sq mm FRLSH, PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red Colour use for Phase & Black Colour use for Neutral),drawn into and including PVC casing- caping (double interlock type) of not less than 25mm width with accessories and fittings such as bends, elbows, tees, crosses, junction box etc, fixed on wall/ceiling with GI saddles, GI screws, rawl plugs etc. for the followingl point controlled by one switch including pressed steel terminal box powder coated of suitable size with 2.8 mm thick bakelite hylam sheet cover, ISI marked with CM/L no of approved make for housing/mounting switches, sockets & regulators etc. and drawing 1.5 sq. mm copper stranded conductor PVC insulated, unsheated cable as earth continuity conductor, connected to common earth and earth dolly , all as specified and directed by Engr-in-Charge Note :-(i) Cost of PVC casing & capping, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

S&F switch piano flush type, single pole, 5/6 Amps, one way complete all as specified and as directed.

S&F ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified and as directed.

S&F LED light fitting 1x9W/1x10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable complete all as specified and as directed.

S&F in repair 6 watt surface mounted round LED Down light Colour (CW) aesthetically designed made by aluminium P-die-cast enclousers, with separate replaceable constant current driver 12 watts for grid ceilling including electrical connection all as directed by Engr-in-Charge

S&F in repairs epoxy powder coated sheet metal enclosure for DBs, double door (when MCBs to be used), Single pole and neutral 240 V, 4 ways with mounting fitted with bus bar, DIN channel, neutral link and incoming contact complete all as specified and as directed.

S&F 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and as directed.

S&F in repairs MCB SPN 32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessry connection complete all as specified and as directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating)

S&F XLPE armoured cable 10 sqmm 2 core,1100 volts grade heavy duty cable,ISI marked passing through pipe, with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed complete all as specified and as directed.

S&F GI Light grade 40 mm dia of size for road cross/cutting on wall floor drain etc complete all as specified and as directed.

S&F switch piano flush type, single pole , 5/6 Amps, one way complete all as specified and as directed.

S&F ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified and as directed.

S&F LED light fitting 1x9W/1x10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable complete all as specified and as directed.

S&F in repair 6 watt surface mounted round LED Down light Colour (CW) aesthetically designed made by aluminium P-die-cast enclousers, with separate replaceable constant current driver 12 watts for grid ceilling including electrical connection all as directed by Engr-in-Charge

S&F in repairs epoxy powder coated sheet metal enclosure for DBs, double door (when MCBs to be used), Single pole and neutral 240 V, 4 ways with mounting fitted with bus bar, DIN channel, neutral link and incoming contact complete all as specified and as directed.

S&F 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and as directed.

S&F in repairs MCB SPN 32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessry connection all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating)

M&L for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth strip electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth strip encased in and including 40 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I complete all as specified and directed and testing on completion. Note :- If the desired earth resistance is not found, earthing shall be redone by the contractor at no extra cost to the department.

S&F XLPE armoured cable 10 sqmm 2 core,1100 volts grade heavy duty cable,ISI marked passing through pipe, with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed complete all as sepcified.

Supply and lay for dry river sand filling for cable protection with a layer of 8cm deep before laying and 15cm covering above the top edge of cable after laying complete all as specified and as directed. (Note : Punned thickness shall be measured).

M&L for sub class B bricks locally available of size 25 x 12.5 x 7.5 cm laid dry width wise across the line of cable in trenches for protection of UG cable complete all as specified and as directed.

S&F GI Light grade 40 mm dia of size for road cross/cutting on wall floor drain etc complete all as specified and as directed.

S&F wall split units indoor/outdoor complete with cordless remote control unit and with in built air ioniser and plasma filter for better indoor air quality with minimum 5 star rating and EER 3.2 of capacity 1.5 TR, ISI marked single phase, 240 volts complete all as specified and as directed

S&F copper wound wall mounted Voltage Stabilizer for automatic operation single phase neaturally air cooled indoor type & designed for input variation between 160V to 270V with output Voltage Stabilizer at 220V to 240V with accuracy of + 2% and of capacity of 4 KVA complete all as specified and as directed.

M&L for Wiring with approved colour coding as per IS (Red, Black and Green for single phase circuits) with two single core 4 Sqmm and one 4.0 Sqmm PVC insulated FRLSH cable with stranded copper conductor drawing into and including PVC Casing caping with all fittings complete all as specified and as directed.

S&F epoxy powder coated sheet metal enclosure for DBs, Single door, Single pole and neutral 240 V,2 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact complete all as specified and as directed.

S&F MCB SPN 32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs including necessry connection complete all as specified and as directed

S&F of switch piano flush type 240 Volts 5 Amps, SP, one way complete all as specified and directed.

S&F ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified and directed.

S&F metallic body ventilating exhaust fan 380 mm sweep with blades 230 volt AC complete with louver and all accessories including grouting bolts, nuts & washers complete all as specified and as directed.

M&L for cutting holes (round type) into or through brick walls built in cement mortar of cement lime mortar and and stone walls built lime mortat or wall of lime concrete suitable for exshaust fan 380 mm sweep including maiking hohe finished with bricks, plaster and distempering complete all as specified and directed

All as per BOQ Srl Item No 139.00 here-in-before but for one socket outlet 5/6 Amps on Independent board complete all as specified and directed.

S&F switch piano flush type, single pole, 6 Amps, one way complete all as specified and directed.

S&F switch socket combination, 2 in 1 multipurpose 5 pin, (6 Amps) complete all as specified and directed.

S&F Socket outlet 3 pin, 5/6A, flush type complete all as specified and directed.

S&F switch socket combination, 2 in 1, 6 pin, 16 Amps flush type controlled by one switch complete all as specified and directed.

S&F ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified.

S&F stepped type electronic fan regulator flush type 240 Volts ISI marked complete all as specified and directed.

S&F lamp holder, PVC/polycarbonate type with back plate straight or angular suitable for batten fittings complete all as specified and directed.

S&F for concealed type sub main wiring with two run of 4.00 Sqmm single core PVC FRLSH, PVC insulated unsheathed stranded copper conductor (Red/yellow/blue wires for phases and black wire for neutral) drawn in and including through Rigid non-metallic PVC conduit(medium) ISI marked of size 25mm bore with all fittings like tee/Bend/Elbow/Reducer/Bell mouth/Junction / Terminal Boxes etc. and fixing accessories such as coupler, lock nuts, saddles, pipe hook etc. of nominal size 25 mm including one run of 4.00 Sqmm single core PVC FRLSH, PVC insulated unsheathed stranded copper conductor as earth wire (green in colour) complete all as specified. Note : (i) Note : 2 runs of line conductor, one run of earth continuity conductor, one run of PVC conduit and one run of cuttinf chases shall be measured as unit length. (ii) Cost of PVC conduit, conductors, cutting chases of wall, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

All as per Item No 178.00 here-in-before but with FRLSH grade, (ISI mark) PVC insulated and unsheathed two run multistranded copper conductor of size 6.0 Sqmm including FRLSH grade (ISI mark), PVC insulated, unsheathed one run multi-stranded copper conductor of size 6.0 sqmm green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed.

S&F of single phase, 1400 RPM, metal exhaust fans AC 230/240 V of size 300 mm sweep with louvre including necessary connection with three core round flexible copper wire of 1 sqmm from connector to fan, minimum 1m length complete all as directed,including taking out the existing burnt out fan complete all as directed by Engr-in-Charge.

S&F LED security light 35 watt (Min) 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp, Aluminum die cast housing High efficiency long life LED package in integral module with lumen efficacy of 110 lm/W (Min) and viewing angle of 45 degree to ensure better uniformity, electronic LED driver (SMPS based constant current supply) with Output Short-circuit protection, Surge protection & other reliability test as per latest IS. operational voltage of 170 volts to 270 volts, frequency of 50 Hz, protection grade IP 66, IK-08 CRI greater than or equal to 70% , CW available CCT of 5700K/6500K, power factor of minimum 0.95 , life span of minimum 50000 working hours cincluding necessary electrical connections by PVC sheathed copper conductor wire of 3 core x 1.5 Sqmm and necessary fixing arrangement all as specified. Note : (i) The minimum requirement of lumen efficiency, lumen output and power consumption has been specified. However, as per availability, the bidders may opted higher specification with out any extra cost. The quoted rate is deem to be included for that and no extra payment will be made on this account. (ii) The fittings should be marked 'Date of installation" and "Date of Procurement" with marker pen

S&F LED light fitting 1x9W/1X10W bulkhead luminaire having IP65 design with luminium die cast housing and vandal-resistant cover finished in epoxy powder-coated housing including LED light driver holder connecting up with an including three core flexible copper conductor cable of suitable size complete all as specified and as directed.

S&F LED 9/10 Watt tube light fitting mirror intregated type, including LED retrofit tube lamp 9/10 W , LED tube light nominal power 9/10 Watt, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 110 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 extruded aluminium LED battens life span of minimum 50000 working hours complete fitting including connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core, and PVC round/ square box white colour x 2 Nos for mounting of fitting complete all as specified & directed

S&F in repairs LED 20 Watt tube light fitting intregated type, including LED retrofit tube lamp 20 W , LED tube light nominal power 20 Watt, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 110 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 life span of minimum 50000 working hours and LED batten with aluminium housing and polycarbonate diffuser complete fitting including connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core, and PVC round/ square box white colour x 2 Nos for mounting of fitting complete all as specified & directed. . Note (i) Make of batten and LED tube lamp should be of same make.

S&F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 100 amps rated busbar, 8 way Double door enclosure made up of CRCA sheet steel,powder coated, IP 43, IK 09 including fixing the DB box flush in wall of any type and making good the distrubed surface to match as the existing with all as specified and directed by Engr-in-charge

S&F 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed.

S&F in repairs MCB SPN 32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessry connection all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating)

M&L for earthing complete with Galvanised steel earth plate electrode 600x600x6 mm mm buried directly in ground (Earth pit not less than 2.25m below ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to GI wire of size 4 mm as earth lead by means of bolt, nuts, check nuts and washers of galvanised iron or steel, upto 7.5m length, earth strip protected by and including 15 mm dia GI pipe (light grade) and connected to main test point or body of pole/pannel or lightening arrester of main controlling switch as directed including concrete pit in PCC (1:3:6) type C1 , Precast RCC (1:2:4) Type B1 cover slab of size 54x54x5 cm reinforced with 8 mm dia TMT bars @ 100 mm C/C both ways with one handle for lifting made out of 10 mm dia TMT bar embedded in precast cover slab, funnel, wire mesh, 20 mm bore GI Pipe (Medium Grade) for watering, Charcoal and salt in alternate layers of 15 cm (Compacted Thickness) around the earth electrode including necessary excavation, earth work in any type of soil and disposal of spoil to a distance n.exc 50 m and necessary testing complete all as shown in Electrical Plate No 3 of SSR Part-I. NOTE : 1. The unit rare includes for protectionh GI pipe of 15mm and watering pipe of 20mm bore including excavation for earth pit in any type of soil/disintegrate rock. 2. Contractor has to bring agriculture soil from outside of defence land and fill in earth pit to acheive desired result as the soil resisitivity is very high. 3. The cost of GI wire of 4mm including protection pipe, from top of earth plate upto 7.5 meter above/below ground level is deemed to be included in the unit rate. 4. All the joints in GI wire and connectgion with earth plate to be welded through brazing and in addition by providing double brass nut bolt and washer. 5.Costing of welding and nut bolts are deemed to be included in the unit rate

Supply, Laying, testing and connecting XLPE sheathed,PVC insulated screened PVC bedded,galvanised steel strip of wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volt grade of size 2 core 10 sqmm. , laid in trenches/surface of wall/in GI pipe along with pole for connection to OH lines,including Brass Compression Cable Gland, Terminal Lugs,clamps,nut & bolts etc all as specified

M&L for sand filling around the cable with approved quality coarse sand for sand cushioning of Under ground cable including spreading and punning down to 18 cm thickness complete all as specified and as directed.(Compacted/Punned thickness shall be measured).

Supply and lay in trench fly ash bricks locally available of size 25 x 12.5 x 7.5 cm laid dry width wise across the line of cable in trenches for protection of UG cable complete all as specified and as directed. (Note : Punned thickness shall be measured).

S&F GI Light grade 40 mm dia of size for road cross/cutting on wall floor drain etc complete all as specified and as directed.

S&F wall mounted fans complete with blades, in built regulator and accessories, 230 V, 300 mm sweep. Min air delivery 50 CFM, 90 degree oscillation and colour white complete all as specified and directed

S&F ventilating exhaust fan with louvers of sweep 380mm, 230 volts 1200 Rpm, with blade and frame abd loures metalic body complete with ISI marked complete all as specified and directed

S&F heavy duty wall mounting fan 450mm sweep, 1450 RPM air delivery 150 CMM 80 watt all as directed by Engr-in-Charge

S&F Pedestal fan (Full steel body) 450mm sweep, 1450 RPM air delivery 150 CMM 80 watt all as directed by Engr-in-Charge

S&F single pointed aluminium air termination rod, 12 mm dia, 300 mm long complete all as specified and as directed.

S&F test point terminal block made of gun metal or phosphorus bronze size 75X75X25 mm, drilled and screwed including 3 nos., 8 mm dia 25 mm long hex head screw complete all as specified and as directed.

S&F aluminium strip of size 20 x 3 mm as earth continuity conductor or main earthing lead fixed on "V" type porcelain insulator, 4 BM, heavy duty ( ceramic bus bar support insulator off white colour of suitable for mounting strip of 20 mm wide x 3 min thick) saddle to wall, buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required brazing to each joints and connected with by providing brass nut bolts and washer all as specified and directed by Engr in Charge. Note : Insulators to be provided on every 50 cm. (Minimum 2 x insulators to be provided in every 1 x metre of strip)

Material and labour for earthing complete with Galvanised steel earth plate electrode 600x600x6 mm mm buried directly in ground (Earth pit not less than 2.25m below ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to GI strip of size 32 x 6 mm as earth lead by means of bolt, nuts, check nuts and washers of galvanised iron or steel, upto 7.5m length, earth strip protected by and including 40 mm dia GI pipe (light grade) and connected to main test point or body of pole/pannel or lightening arrester of main controlling switch as directed including concrete pit in PCC (1:3:6) type C1 , Precast RCC (1:2:4) Type B1 cover slab of size 54x54x5 cm reinforced with 8 mm dia TMT bars @ 100 mm C/C both ways with one handle for lifting made out of 10 mm dia TMT bar embedded in precast cover slab, funnel, wire mesh, 20 mm bore GI Pipe (Medium Grade) for watering, Charcoal and salt in alternate layers of 15 cm (Compacted Thickness) around the earth electrode including necessary excavation, earth work in any type of soil and disposal of spoil to a distance n.exc 50 m and necessary testing complete all as shown in Electrical Plate No 3 of SSR Part-I. NOTE : 1. The unit rare includes for protectionh GI pipe of 40mm and watering pipe of 20mm bore including excavation for earth pit in any type of soil/disintegrate rock. 2. Contractor has to bring agriculture soil from outside of defence land and fill in earth pit to acheive desired result as the soil resisitivity is very high. 3. The cost of GI strip including protection pipe, from top of earth plate upto 7.5 meter above/below ground level is deemed to be included in the unit rate. 4. All the joints in GI wire and connectgion with earth plate to be welded through brazing and in addition by providing double brass nut bolt and washer. 5.Costing of welding and nut bolts are deemed to be included in the unit rate

S&F GI strip of size 32 x 6 mm as earth continuity conductor or main earthing lead fixed on "V" type porcelain insulator, 10 BM, heavy duty ( ceramic bus bar support insulator off white colour of suitable for mounting strip of 32 mm wide x 6 min thick) saddle to wall, buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required brazing to each joints and connected with by providing brass nut bolts and washer all as specified and directed by Engr in Charge. Note : Insulators to be provided on every 50 cm. (Minimum 2 x insulators to be provided in every 1 x metre of strip)

M/S SUSHMA INFRA PROJECT AND POWER (BID ID -3156870)

S.P.S. SUPPLIERS (BID ID -3156848)

Jaibalaji Enterprise (BID ID -3157129)

SANJAY KUMAR SUPAN (BID ID -3156882)

ANSH CONSTRUCTION (BID ID -3157177)

SINGH CONSTRUCTION (BID ID -3157210)

M/S DYNAMIC INDIA (PROJECT) CONSTRUCTION (BID ID -3157252)