(i) Construction of Parcel office and RMS building including associated Electrical works(Composite work) at Jharsuguda Railway Station (ii) Civil Engineering work in connection with Interlocking of Non-interlocked Engineering L.C. Gate Nos. B- 11(BNDM Yard), RB-1(ROU-KRMD)and RB-1(Link C-DMF) in Chakradharpur Division

A-Execution of Civil Engineering works as per items of CPWD DSR 2023

B-Execution of Civil Engineering works as per items of CPWD DSR 2023

C-Execution of Electrical(G) work (Supply items) Note:- This schedule to

D-Execution of Electrical(G) works (Erection items) Note :- This schedule

Execution of Civil Engineering works for Construction of Parcel office and RMS building at

Item- 1 Jharsuguda Railway Station as per items of CPWD DSR 2023 except steel reinforcement (Item

Directory -CPWD DSR 2023-Ver-1)

S No. Item No Description of Item Unit Qty Rate Amount

2.0 EARTH WORK

2.1S General

Earth work in excavation by mechanical

means (Hydraulic excavator)/manual

means over areas (exceeding 30 cm in

2.6 depth, 1.5 m in width as well as 10 sqm on

plan) including getting out and disposal of

excavated earth lead upto 50 m and for all

lift, as directed by Engineer-in-charge.

2.25A Excavating, supplying and filling of local cum 3000 700.5 2101500

earth (including royalty) by mechanical

transport upto a lead of 5km also including

ramming and watering of the earth in

layers not exceeding 20 cm in trenches,

plinth, sides of foundation etc. complete.

2.27 Supplying and filling in plinth with sand cum 600 2123.75 1274250

3 under floors, including watering, ramming,

consolidating and dressing complete.

4.0 CONCRETE WORK

4.1S CEMENT CONCRETE (CAST IN SITU)

Providing and laying in position cement

concrete of specified grade excluding the

cost of centering and shuttering - All work

up to plinth level :

(zone-III) derived from natural sources : 3

graded stone aggregate 20 mm nominal

size derived from natural sources)

derived from natural sources : 4 graded

stone aggregate 20 mm nominal size

derived from natural sources)

derived from natural sources : 6 graded

stone aggregate 20 mm nominal size

derived from natural sources)

CKP-DIVN-ENGG/SOUTH EASTERN RLY

Centering and shuttering including

4.3 strutting, propping etc. and removal of

form work for :

7 4.3.1 Foundations, footings, bases for columns Sqm 350 392.15 137252.5

4.10S DAMP-PROOF COURSE

4.11 Providing and laying damp-proof course Sqm 250 495.75 123937.5

50mm thick with cement concrete 1:2:4 (1

cement : 2 coarse sand (zone-III) derived

from natural sources : 4 graded stone

aggregate 20mm nominal size derived

from natural sources).

5.0 REINFORCEMENT CEMENT CONCRETE

5.1S CAST IN SITU

Providing and laying in position specified

grade of reinforced cement concrete,

5.1 excluding the cost of centering, shuttering,

finishing and reinforcement - All work up

to plinth level :

III) derived from natural sources : 3 graded

stone aggregate 20 mm nominal size

derived from natural sources)

Reinforced cement concrete work in walls

(any thickness), including attached

pilasters, buttresses, plinth and string

courses, fillets, columns, pillars, piers,

abutments, posts and struts etc. above

plinth level up to floor five level, excluding

cost of centering, shuttering, finishing and

reinforcement :

III) derived from natural sources : 3 graded

stone aggregate 20 mm nominal size

derived from natural sources)

5.3 Reinforced cement concrete work in cum 60 11505.5 690330

beams, suspended floors, roofs having

slope up to 15 degree landings, balconies,

shelves, chajjas, lintels, bands, plain

window sills, staircases and spiral stair

cases above plinth level up to floor five

11 level, excluding the cost of centering,

shuttering, finishing and reinforcement

with 1:1.5:3 (1 cement : 1.5 coarse

sand(zone-III) derived from natural sources

: 3 graded stone aggregate 20 mm

nominal size derived from natural

5.9S FORM WORK

Centering and shuttering including

5.9 strutting, propping etc. and removal of

5.9.1 Foundations, footings, bases of columns, Sqm 400 392.15 156860

etc. for mass concrete

5.9.2 Walls (any thickness) including attached Sqm 250 842.5 210625

13 pilasters, buttresses, plinth and string

5.9.3 Suspended floors, roofs, landings, Sqm 2000 927.25 1854500

balconies and access platform

5.9.5 Lintels, beams, plinth beams, girders, Sqm 300 736.4 220920

bressummers and cantilevers

5.9.6 Columns, Pillars, Piers, Abutments, Posts Sqm 1500 961.3 1441950

6.0 MASONRY WORK

6.1S General

CKP-DIVN-ENGG/SOUTH EASTERN RLY

Brick work with common burnt clay F.P.S.

6.1 (non modular) bricks of class designation

7.5 in foundation and plinth in:

6.26S EXPOSED BRICK WALL

Half brick masonry with non modular fly

ash bricks of class designation 10,

conforming to IS :12894, in super structure

above plinth and upto floor V level

6.47 Providing and laying Autoclaved Aerated cum 500 8333.65 4166825

Concrete (AAC) blocks masonry with 150

mm to 300 mm thick with Grade -1 AAC

blocks of density 551 to 650 kg/cum

conforming to IS: 2185 (Part 3) in super

structure above plinth level up to floor V

level with RCC band at sill level and lintel

level with approved block laying polymer

modified adhesive mortar all complete as

per direction of Engineer-in-Charge. (The

payment of RCC band and reinforcement

shall be made for separately).

8.0 CLADDING WORK

8.1S General

Providing and fixing 18 mm thick gang

saw cut, mirror polished, premoulded and

prepolished, machine cut for kitchen

platforms, vanity counters, window sills,

facias and similar locations of required

size, approved shade, colour and texture

8.2 laid over 20 mm thick base cement mortar

1:4 (1 cement : 4 coarse sand), joints

treated with white cement, mixed with

matching pigment, epoxy touch ups,

including rubbing, curing, moulding and

polishing to edges to give high gloss finish

etc. complete at all levels

Granite stone slab all colour and texture

except black, Cherry/Ruby red

9.0 WOOD AND P.V.C. WORK

9.1S FRAMES AND TRUSSES

Providing and fixing ISI marked flush door

shutters conforming to IS : 2202 (Part I)

decorative type, core of block board

construction with frame of 1st class hard

wood and well matched teak 3 ply

veneering with vertical grains or cross

bands and face veneers on both faces of

21 Stainless Steel butt hinges with necessary

ANODISED ALUMINIUM FITTINGS (ALL

FITTINGS SHALL BE ISI MARKED)

Providing and fixing aluminium tower

bolts, ISI marked, anodised (anodic

coating not less than grade AC 10 as per IS

: 1868 ) transparent or dyed to required

colour or shade, with necessary screws

etc. complete :

9.105S GYPSUM BOARD PARTITIONS

CKP-DIVN-ENGG/SOUTH EASTERN RLY

9.119 Providing and fixing factory made P.V.C. Metre 400 492.7 197080

door frame of size 50x47 mm with a wall

thickness of 5 mm, made out of extruded

5 mm rigid PVC foam sheet, mitred at

corners and joined with 2 Nos of 150 mm

long brackets of 15x15 mm M.S. square

tube, the vertical door frame profiles to be

24 reinforced with 19x19 mm M.S. square

tube of 19 gauge, EPDM rubber gasket

weather seal to be provided through out

the frame. The door frame to be fixed to

the wall using M.S. screws of 65/100 mm

size, complete as per manufacturer's

specification and direction of Engineer- in-

Providing and fixing factory made panel

PVC door shutter consisting of frame made

out of M.S. tubes of 19 gauge thickness

and size of 19 mm x 19 mm for styles and

15x15 mm for top & bottom rails. M.S.

frame shall have a coat of steel primers of

approved make and manufacture. M.S.

frame covered with 5 mm thick heat

moulded PVC 'C' channel of size 30 mm

thickness, 70 mm width out of which 50

mm shall be flat and 20 mm shall be

tapered in 45 degree angle on both side

forming styles and 5 mm thick, 95 mm

wide PVC sheet out of which 75mm shall

be flat and 20 mm shall be tapered in 45

degree on the inner side to form top and

bottom rail and 115 mm wide PVC sheet

9.120 out of which 75 mm shall be flat and 20

mm shall be tapered on both sides to form

lock rail. Top, bottom and lock rails shall

be provided both side of the panel. 10 mm

(5 mm x 2 ) thick, 20 mm wide cross PVC

sheet be provided as gap insert for top rail

& bottom rail, panelling of 5 mm thick

both side PVC sheet to be fitted in the M.S.

frame welded/ sealed to the styles & rails

with 7 mm (5 mm+2 mm) thick x 15 mm

wide PVC sheet beading on inner side, and

joined together with solvent cement

adhesive. An additional 5 mm thick PVC

strip of 20 mm width is to be stuck on the

interior side of the 'C' Channel using PVC

solvent adhesive etc. complete as per

direction of Engineer-in-charge,

manufacturer's specification & drawing.

Providing and fixing bright /matt finished

Stainless Steel handles of approved

quality & make with necessary screws etc

10.0 STEEL WORK

10.1S General

10.1 Structural steel work in single section, Kg 13000 117.35 1525550

fixed with or without connecting plate,

27 including cutting, hoisting, fixing in

position and applying a priming coat of

approved steel primer all complete.

10.2 Structural steel work riveted, bolted or Kg 28000 133.7 3743600

welded in built up sections, trusses and

framed work, including cutting, hoisting,

fixing in position and applying a priming

coat of approved steel primer all

CKP-DIVN-ENGG/SOUTH EASTERN RLY

10.3 Providing and fixing in position collapsible Sqm 10 11439.6 114396

steel shutters with vertical channels

20x10x2 mm and braced with flat iron

diagonals 20x5 mm size, with top and

29 bottom rail of T-iron 40x40x6 mm, with 40

mm dia steel pulleys, complete with bolts,

nuts, locking arrangement, stoppers,

handles, including applying a priming coat

of approved steel primer.

10.19 Providing and fixing mild steel round Kg 2000 97.2 194400

30 holding down bolts with nuts and washer

plates complete.

Steel work welded in built up sections/

framed work, including cutting, hoisting,

10.25 fixing in position and applying a priming

coat of approved steel primer using

structural steel etc. as required.

10.25.2 In gratings, frames, guard bar, ladder, Kg 7000 172.6 1208200

railings, brackets, gates and similar works

10.28 Providing and fixing stainless steel ( Grade Kg 5000 772.4 3862000

304) railing made of Hollow tubes,

channels, plates etc., including welding,

grinding, buffing, polishing and making

curvature (wherever required) and fitting

the same with necessary stainless steel

nuts and bolts complete, including fixing

the railing with necessary accessories &

32 stainless steel dash fasteners , stainless

steel bolts etc., of required size, on the top

of the floor or the side of waist slab with

suitable arrangement as per approval of

Engineer-in-charge, (for payment purpose

only weight of stainless steel members

shall be considered excluding fixing

accessories such as nuts, bolts, fasteners

11.0 FLOORING

11.37S CERAMIC GLAZED TILES

11.37 Providing and laying Ceramic glazed floor Sqm 1000 1096.55 1096550

tiles of size 300x300 mm (thickness to be

specified by the manufacturer) of 1st

quality conforming to IS : 15622 of

approved make in colours such as White,

33 Ivory, Grey, Fume Red Brown, laid on 20

mm thick cement mortar 1:4 (1 Cement : 4

Coarse sand), Jointing with grey cement

slurry @ 3.3 kg/sqm including pointing the

joints with white cement and matching

pigment etc., complete.

11.41S VITRIFIED FLOOR TILES

Providing and laying Vitrified tiles in floor

in different sizes (thickness to be specified

by the manufacturer) with water

absorption less than 0.08% and

conforming to IS:15622, of approved

brand & manufacturer, in all colours and

shade, laid on 20 mm thick cement mortar

1:4 (1 cement: 4 coarse sand) jointing with

11.41A grey cement slurry @3.3 kg/sqm including

grouting the joints with white cement and

matching pigments etc. The tiles must be

cut with the zero chipping diamond cutter

only . Laying of tiles will be done with the

notch trowel, plier, wedge, clips of

required thickness, leveling system and

rubber mallet for placing the tiles gently

Double charge vitrified tile polished finish

CKP-DIVN-ENGG/SOUTH EASTERN RLY

12.0 ROOFING

12.37S RAIN WATER SPOUT AND PIPE

Providing and fixing on wall face

unplasticised Rigid PVC rain water pipes

conforming to IS : 13592 Type A, including

jointing with seal ring conforming to IS :

5382, leaving 10 mm gap for thermal

expansion, (i) Single socketed pipes.

12.50 Providing and fixing precoated galvanised Sqm 800 738.65 590920

iron profile sheets (size, shape and pitch

of corrugation as approved by Engineer-in-

charge) of total coated thickness 0.50 mm

(base metal of minimum 0.45 mm

thickness with total coating thickness of

0.05 mm) with zinc coating 120 grams per

sqm as per IS: 277, in 240 mpa steel

grade, 5-7 microns epoxy primer on both

side of the sheet and polyester top coat

15-18 microns. Sheet should have

36 protective guard film of 25 microns

minimum to avoid scratches during

transportation and should be supplied in

single length upto 12 metre or as desired

by Engineer-in-charge. The sheet shall be

fixed using self drilling /self tapping screws

of size (5.5x 55 mm) with EPDM seal,

complete upto any pitch in horizontal/

vertical or curved surfaces, excluding the

cost of purlins, rafters and trusses and

including cutting to size and shape

wherever required.

Providing and fixing precoated galvanised

steel sheet roofing accessories of total

coated thickness 0.50 mm (base metal of

minimum 0.45 mm thickness with total

coating thickness of 0.05 mm) with Zinc

coating 120 grams per sqm as per IS: 277,

in 240 mpa steel grade, 5-7 microns epoxy

primer on both side of the sheet and

polyester top coat 15-18 microns using

self drilling/ self tapping screws complete :

13.0 FINISHING

13.1S CEMENT PLASTER (IN FINE SAND)

13.1 12 mm cement plaster of mix :

15 mm cement plaster on the rough side

of single or half brick wall of mix :

13.20S PEBBLE DASH PLASTER

13.26 Providing and applying plaster of paris Sqm 6000 262.7 1576200

putty of 2 mm thickness over plastered

surface to prepare the surface even and

smooth complete.

13.37S INTERIOR FINISHING

Distempering with 1st quality acrylic

distemper (ready mixed) having VOC

content less than 50 gram/litre, of

approved manufacturer and of required

shade and colour all complete to achieve

even shade and colour :

CKP-DIVN-ENGG/SOUTH EASTERN RLY

13.41.1 New work (two or more coats) over and Sqm 6500 185.65 1206725

including water thinnable priming coat

with cement primer having VOC content

less than 50 gram/litre

13.44S EXTERIOR FINISHING

Finishing walls with water proofing cement

paint of required shade :

13.44.1 New work (Two or more coats applied @ Sqm 600 116.9 70140

3.84 kg/10 sqm)

Finishing with Deluxe Multi surface paint

system for interiors and exteriors using

Primer as per manufacturers specifications

13.48.2 Painting wood work with Deluxe Multi Sqm 50 176.25 8812.5

Surface Paint of required shade. Two or

more coat applied @ 0.90 ltr/10 sqm over

an under coat of primer applied @0.75

ltr/10 sqm of approved brand and

13.48.3 Painting Steel work with Deluxe Multi Sqm 400 170.7 68280

Surface Paint to give an even shade. Two

or more coat applied @ 0.90 ltr/10 sqm

over an under coat of primer applied @

0.80 ltr/10 sqm of approved brand and

Finishing walls with 100% Premium acrylic

emulsion paint (Company Depot Tinted)

having VOC less than 50 gm/litre and UV

13.48A resistance as per IS 15489:2004, Alkali &

fungal resistance, dirt resistance exterior

paint of required shade with silicon

13.48A.1 New work (Two or more coats applied @ Sqm 1500 181.25 271875

1.43 litre/ 10 sqm. Over and including

priming coat of exterior primer applied @

0.90 litre/10 sqm.

15.0 DISMANTLING AND DEMOLISHING

15.1S General

Demolishing cement concrete manually/

by mechanical means including disposal of

material within 50 metres lead as per

direction of Engineer - in - charge.

(including equivalent design mix)

15.3 Demolishing R.C.C. work manually/ by cum 100 3551.25 355125

mechanical means including stacking of

47 steel bars and disposal of unserviceable

material within 50 metres lead as per

direction of Engineer - in- charge.

Demolishing brick work manually/ by

mechanical means including stacking of

serviceable material and disposal of

unserviceable material within 50 metres

lead as per direction of Engineer-in-

Dismantling doors, windows and clerestory

windows (steel or wood) shutter including

15.12 chowkhats, architrave, holdfasts etc.

complete and stacking within 50 metres

Dismantling steel work in single sections

15.17 including dismembering and stacking

within 50 metres lead in:

CKP-DIVN-ENGG/SOUTH EASTERN RLY

15.24 Demolishing dry brick pitching in floors, cum 50 1317.65 65882.5

drains etc. including stacking of

52 serviceable material and disposal of

unserviceable material within 50 metres

Dismantling roofing including ridges, hips,

15.28 valleys and gutters etc., and stacking the

material within 50 metres lead of:

15.60 Disposal of building rubbish / malba / cum 380 263.95 100301

similar unserviceable, dismantled or waste

materials by mechanical means, including

loading, transporting, unloading to

approved municipal dumping ground or as

approved by Engineer-in-charge, beyond

50 m initial lead, for all leads including all

lifts involved.

17.0 SANITARY INSTALLATIONS

17.1S General

Providing and fixing water closet squatting

pan (Indian type W.C. pan ) with 100 mm

sand cast Iron P or S trap, 10 litre low level

white P.V.C. flushing cistern, including

17.1 flush pipe, with manually controlled device

(handle lever) conforming to IS : 7231,with

all fittings and fixtures complete, including

cutting and making good the walls and

floors wherever required:

17.1.1 White Vitreous china Orissa pattern W.C. Each 10 6767.4 67674

55 pan of size 580x440 mm with integral type

Providing and fixing white vitreous china

pedestal type water closet (European type

W.C. pan) with seat and lid, 10 litre low

level white P.V.C. flushing cistern,

including flush pipe, with manually

controlled device (handle lever),

conforming to IS : 7231, with all fittings

and fixtures complete, including cutting

and making good the walls and floors

wherever required :

17.2.1 W.C. pan with ISI marked white solid Each 20 6515.55 130311

plastic seat and lid

Providing and fixing wash basin with C.I.

brackets, 15 mm C.P. brass pillar taps, 32

mm C.P. brass waste of standard pattern,

including painting of fittings and brackets,

cutting and making good the walls

wherever require:

17.7.1 White Vitreous China Wash basin size Each 15 2648.85 39732.75

57 630x450 mm with a pair of 15 mm C.P.

brass pillar taps

Providing and fixing mirror of superior

glass (of approved quality) and of required

17.32 shape and size with plastic moulded frame

of approved make and shade with 6 mm

thick hard board backing :

17.71 Providing and fixing PTMT liquid soap Each 15 168.35 2525.25

container 109 mm wide, 125 mm high and

112 mm distance from wall of standard

shape with bracket of the same materials

with snap fittings of approved quality and

colour, weighing not less than 105 gms.

CKP-DIVN-ENGG/SOUTH EASTERN RLY

Providing and fixing PTMT towel rail

complete with brackets fixed to wooden

17.73 cleats with CP brass screws with

concealed fittings arrangement of

approved quality and colour.

17.73.1 450 mm long towel rail with total length of Each 10 673.4 6734

60 495 mm, 78 mm wide and effective height

of 88 mm, weighing not less than 170 gms

18.0 WATER SUPPLY

18.7S C.P.V.C. PIPES

Providing and fixing Chlorinated Polyvinyl

Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply,

including all CPVC plain & brass threaded

fittings and fixing the pipe with clamps at

1.00 m spacing. This includes jointing of

18.8 pipes & fittings with one step CPVC solvent

cement and the cost of cutting chases and

making good the same including testing of

joints complete as per direction of

Engineer in Charge. Concealed work,

including cutting chases and making good

Providing and fixing Chlorinated Polyvinyl

Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply

including all CPVC plain & brass threaded

18.9 fittings This includes jointing of pipes &

fittings with one step CPVC solvent

cement, trenching, refilling & testing of

joints complete as per direction of

Engineer in Charge. External work

18.15S BRASS FITTINGS

Providing and fixing brass stop cock of

approved quality :

C.I. SLUICE VALVES/ FIRE HYDRANTS &

18.48 Providing and placing on terrace (at all Per Litre 4000 11 44000

floor levels) polyethylene water storage

tank, IS : 12701 marked, with cover and

66 suitable locking arrangement and making

necessary holes for inlet, outlet and

overflow pipes but without fittings and the

base support for tank.

18.54S PTMT FITTINGS

Providing and fixing PTMT bib cock of

approved quality and colour.

weighing not less than 88 gms

21.0 ALUMINIUM WORK

21.1S General

CKP-DIVN-ENGG/SOUTH EASTERN RLY

Providing and fixing aluminium work for

doors, windows, ventilators and partitions

with extruded built up standard tubular

sections/ appropriate Z sections and other

sections of approved make conforming to

IS: 733 and IS: 1285, fixing with dash

fasteners of required dia and size,

including necessary filling up the gaps at

junctions, i.e. at top, bottom and sides

with required EPDM rubber/ neoprene

gasket etc. Aluminium sections shall be

smooth, rust free, straight, mitred and

jointed mechanically wherever required

including cleat angle, Aluminium snap

beading for glazing / panelling, C.P. brass /

stainless steel screws, all complete as per

architectural drawings and the directions

of Engineer-in-charge. (Glazing, panelling

and dash fasteners to be paid for

21.1.1 For fixed portion

transparent or dyed to required shade

according to IS: 1868, Minimum anodic

coating of grade AC 15)

For shutters of doors, windows &

ventilators including providing and fixing

hinges/ pivots and making provision for

21.1.2 fixing of fittings wherever required

including the cost of EPDM rubber /

neoprene gasket required (Fittings shall

be paid for separately)

transparent or dyed to required shade

according to IS: 1868, Minimum anodic

coating of grade AC 15)

Providing and fixing glazing in aluminium

door, window, ventilator shutters and

partitions etc. with EPDM rubber /

21.3 neoprene gasket etc. complete as per the

architectural drawings and the directions

of engineer-in-charge . (Cost of aluminium

snap beading shall be paid in basic item):

21.3.1 With float glass panes of 4.0 mm thickness Sqm 80 1176.8 94144

(weight not less than 10kg/sqm)

Execution of Civil Engineering works for Interlocking of Non-interlocked Engineering L.C. Gate Nos.

Item- 2 B-11(BNDM Yard), RB-1(ROU-KRMD) and RB-1(Link C-DMF) as per items of CPWD DSR 2023 (Except

Steel Reinforcement) (Item Directory -CPWD DSR 2023-Ver-1)

S No. Item No Description of Item Unit Qty Rate Amount

2.0 EARTH WORK

2.1S General

Earth work in excavation by mechanical

means (Hydraulic excavator) / manual

means in foundation trenches or drains

(not exceeding 1.5 m in width or 10 sqm

2.8 on plan), including dressing of sides and

ramming of bottoms, for all lift, including

getting out the excavated soil and disposal

of surplus excavated soil as directed,

within a lead of 50 m.

CKP-DIVN-ENGG/SOUTH EASTERN RLY

2.25A Excavating, supplying and filling of local cum 120 700.5 84060

earth (including royalty) by mechanical

transport upto a lead of 5km also including

ramming and watering of the earth in

layers not exceeding 20 cm in trenches,

plinth, sides of foundation etc. complete.

2.27 Supplying and filling in plinth with sand cum 30 2123.75 63712.5

3 under floors, including watering, ramming,

consolidating and dressing complete.

4.0 CONCRETE WORK

4.1S CEMENT CONCRETE (CAST IN SITU)

Providing and laying in position cement

concrete of specified grade excluding the

cost of centering and shuttering - All work

up to plinth level :

derived from natural sources : 6 graded

stone aggregate 40 mm nominal size

derived from natural sources)

Providing and laying cement concrete in

retaining walls, return walls, walls (any

thickness) including attached pilasters,

columns, piers, abutments, pillars, posts,

struts, buttresses, string or lacing courses,

parapets, coping, bed blocks, anchor

blocks, plain window sills, fillets, sunken

floor etc., up to floor five level, excluding

the cost of centering, shuttering and

derived from natural sources : 4 graded

stone aggregate 20 mm nominal size

derived from natural sources)

4.10S DAMP-PROOF COURSE

4.11 Providing and laying damp-proof course Sqm 36 495.75 17847

50mm thick with cement concrete 1:2:4 (1

cement : 2 coarse sand (zone-III) derived

from natural sources : 4 graded stone

aggregate 20mm nominal size derived

from natural sources).

4.12 Extra for providing and mixing water per bag 519 18.15 9419.85

proofing material in cement concrete work of 50 kg

in doses by weight of cement as per cement

manufacturer's specification. used

5.0 REINFORCEMENT CEMENT CONCRETE

5.1S CAST IN SITU

Providing and laying in position specified

grade of reinforced cement concrete,

5.1 excluding the cost of centering, shuttering,

finishing and reinforcement - All work up

to plinth level :

III) derived from natural sources : 3 graded

stone aggregate 20 mm nominal size

derived from natural sources)

Reinforced cement concrete work in walls

(any thickness), including attached

pilasters, buttresses, plinth and string

courses, fillets, columns, pillars, piers,

abutments, posts and struts etc. above

plinth level up to floor five level, excluding

cost of centering, shuttering, finishing and

reinforcement :

III) derived from natural sources : 3 graded

stone aggregate 20 mm nominal size

derived from natural sources)

CKP-DIVN-ENGG/SOUTH EASTERN RLY

5.3 Reinforced cement concrete work in cum 18 11505.5 207099

beams, suspended floors, roofs having

slope up to 15 degree landings, balconies,

shelves, chajjas, lintels, bands, plain

window sills, staircases and spiral stair

cases above plinth level up to floor five

10 level, excluding the cost of centering,

shuttering, finishing and reinforcement

with 1:1.5:3 (1 cement : 1.5 coarse

sand(zone-III) derived from natural sources

: 3 graded stone aggregate 20 mm

nominal size derived from natural

5.9S FORM WORK

Centering and shuttering including

5.9 strutting, propping etc. and removal of

5.9.1 Foundations, footings, bases of columns, Sqm 45 392.15 17646.75

etc. for mass concrete

5.9.3 Suspended floors, roofs, landings, Sqm 45 927.25 41726.25

balconies and access platform

5.9.5 Lintels, beams, plinth beams, girders, Sqm 120 736.4 88368

bressummers and cantilevers

5.9.6 Columns, Pillars, Piers, Abutments, Posts Sqm 45 961.3 43258.5

6.0 MASONRY WORK

6.1S General

Brick work with common burnt clay F.P.S.

6.1 (non modular) bricks of class designation

7.5 in foundation and plinth in:

Brick work with common burnt clay F.P.S.

(non modular) bricks of class designation

7.5 in superstructure above plinth level up

to floor V level in all shapes and sizes in :

9.0 WOOD AND P.V.C. WORK

9.40S MISCELLANEOUS-WOOD WORK

Providing and fixing M.S. grills of required

pattern in frames of windows etc. with

9.48 M.S. flats, square or round bars etc.

including priming coat with approved steel

primer all complete.

10.0 STEEL WORK

10.1S General

Steel work welded in built up sections/

framed work, including cutting, hoisting,

10.25 fixing in position and applying a priming

coat of approved steel primer using

structural steel etc. as required.

10.25.2 In gratings, frames, guard bar, ladder, Kg 1170 172.6 201942

railings, brackets, gates and similar works

11.0 FLOORING

11.1S General

Cement concrete flooring 1:2:4 (1 cement

: 2 coarse sand : 4 graded stone

aggregate) finished with a floating coat of

neat cement, including cement slurry, but

excluding the cost of nosing of steps etc.

stone aggregate

CKP-DIVN-ENGG/SOUTH EASTERN RLY

11.16S TILE FLOORING

Providing and fixing 10 mm thick acid

and/or alkali resistant tiles of approved

make and colour using acid and/or alkali

11.21 resisting mortar bedding, and joints filled

with acid and/or alkali resisting cement as

per IS : 4457, complete as per the

direction of Engineer-in- Charge.

In flooring on a bed of 10 mm thick mortar

1:4 (1 acid proof cement : 4 coarse sand)

In dado/skirting on 12 mm thick mortar 1:4

(1 acid proof cement : 4 coarse sand)

13.0 FINISHING

13.1S CEMENT PLASTER (IN FINE SAND)

15 mm cement plaster on the rough side

of single or half brick wall of mix :

13.16S 6 mm CEMENT PLASTER

13.37S INTERIOR FINISHING

Distempering with 1st quality acrylic

distemper (ready mixed) having VOC

content less than 50 gram/litre, of

approved manufacturer and of required

shade and colour all complete to achieve

even shade and colour :

13.41.1 New work (two or more coats) over and Sqm 600 185.65 111390

including water thinnable priming coat

with cement primer having VOC content

less than 50 gram/litre

13.44S EXTERIOR FINISHING

Finishing walls with water proofing cement

paint of required shade :

13.44.1 New work (Two or more coats applied @ Sqm 330 116.9 38577

3.84 kg/10 sqm)

Painting with synthetic enamel paint of

13.61 approved brand and manufacture to give

an even shade :

Schedule B-Execution of Civil Engineering works as per items of CPWD DSR 2023 for Steel

reinforcement only

Execution of Civil Engineering works for Construction of Parcel office and RMS building at

Item- 1 Jharsuguda Railway Station as per items of CPWD DSR 2023 for Steel reinforcement only (Item

Directory -CPWD DSR 2023-Ver-1)

S No. Item No Description of Item Unit Qty Rate Amount

5.0 REINFORCEMENT CEMENT CONCRETE

5.22S STEEL REINFORCEMENT

Steel reinforcement for R.C.C. work

including straightening, cutting, bending,

placing in position and binding all

complete upto plinth level.

5.22.6 Thermo-Mechanically Treated bars of Kg 60000 107.85 6471000

grade Fe-500D or more.

Steel reinforcement for R.C.C. work

including straightening, cutting, bending,

placing in position and binding all

complete above plinth level.

CKP-DIVN-ENGG/SOUTH EASTERN RLY

5.22A.6 Thermo-Mechanically Treated bars of Kg 33000 107.85 3559050

grade Fe-500D or more.

Execution of Civil Engineering works for interlocking of Non-interlocked Engineering L.C. Gate Nos.

Item- 2 B-11(BNDM Yard), RB-1(ROU-KRMD) and RB-1(Link C-DMF) as per items of CPWD DSR 2023 for

Steel reinforcement only (Item Directory -CPWD DSR 2023-Ver-1)

S No. Item No Description of Item Unit Qty Rate Amount

5.0 REINFORCEMENT CEMENT CONCRETE

5.22S STEEL REINFORCEMENT

Steel reinforcement for R.C.C. work

including straightening, cutting, bending,

placing in position and binding all

complete upto plinth level.

5.22.6 Thermo-Mechanically Treated bars of Kg 2250 107.85 242662.5

grade Fe-500D or more.

Steel reinforcement for R.C.C. work

including straightening, cutting, bending,

placing in position and binding all

complete above plinth level.

5.22A.6 Thermo-Mechanically Treated bars of Kg 4350 107.85 469147.5

grade Fe-500D or more.

Schedule C-Execution of Electrical(G) work (Supply items) Note:- This schedule to be read in

Schedule conjunction with the Technical Explanatory Note, General explanatory Note & mentioned

specifications. Type of wiring to be done : Concealed & Modular type.

Item- 1 Supply of Electrical items

S No. Item No Description of Item Unit Qty Rate Amount

1 1 Supply of XLPE insulated, PVC sheathed Metre 500.00 979.40 489700.00

armoured UG circular Aluminium

conductor cable of size 4 core 150 sq mm

of 1100 V grade (C2 category).

2 2 Supply of XLPE insulated, PVC sheathed Metre 500.00 166.00 83000.00

armoured UG circular Aluminium

conductor cable of size 4 core 16 sq mm

of 1100 V grade (C2 category).

with all accessories.

6 6 Supply of GI perforated type cable tray Metre 100.00 833.24 83324.00

made of standard length of 2.5 mtr with

all accessories.

7 7 Supply of LED street light fitting 45W with Numbers 6.00 1625.72 9754.32

all accessories.

8 8 Supply of three phase astronomical timer Numbers 1.00 13353.09 13353.09

based street light panel with all

9 9 Supply , testing of LT panel consist of 1 Numbers 1.00 73455.00 73455.00

No.125 Amp 36 kA FP MCCB as a incoming

, 02 Nos. 63 Amp FP MCCB as a outgoing

and 32 A DP MCB-7 Nos. as a outgoing

with cable termination.

10 10 Supply & erection of vertical TPN DB with Numbers 3.00 20928.53 62785.59

incomer 1 No. 100A MCCB and outgoing 3

nos 63A MCB, 3 Nos SP MCB 16A/25A/32A

with all accessories including wiring.

11 11 Supply of SPN 18- way DB (DD) consisting Numbers 8.00 5211.98 41695.84

of DP 63A 10 kA MCB - 1 no. as incoming

and 6A -16A 10kA SP MCB - 4 Nos, 20A -

32A 10kA DP MCB - 4 Nos as outgoing.

12 12 "Supply, erection, testing & commissioning Numbers 12.00 3438.50 41262.00

of 63A capacity RCCB. "

CKP-DIVN-ENGG/SOUTH EASTERN RLY

13 13 "Supply and fixing of double pole (single Numbers 8.00 1985.23 15881.84

phase and neutral), 240 volts, 40 Amp

RCCB, 30mA sensitivity in the existing

MCB DB complete with connections,

testing and commissioning. . "

14 14 Supply and installation of 8Way SPN MCB Numbers 4.00 2440.52 9762.08

DB consisting of the following. i) SP&N

8Way MCB DB Box - 1No. ii) 32A-40 SP

Isolator - 1No. (iii) SP MCB (6-32A) - 7Nos.

(6A MCB for lighting load 16A MCB for AC

15 15 Supply of 5 star rated 2 Ton inverter Numbers 8.00 54988.00 439904.00

(variable speed) type split Air Conditioner,

operating Voltage 230 V, AC with function

of cooling only, rotary compressor, 100%

copper coil, eco friendly refrigerant ,

minimum ISEER of 5.0, BEE star rating: 5

conforming to CEGE/GRC's specification

dated 25.11.2024

16 16 "Supply, fixing, testing and commissioning Numbers 18.00 647.93 11662.74

of AC supply box (2 way SPN/DB) along

with the 25 Amp SPN MCB for controlling

AC/Gyser unit . "

sweep with all accessories.

18 18 Supply of recess mounted Square panel (2 Numbers 30.00 2767.36 83020.80

feet x 2 feet) luminaire complete with all

19 19 Supply of 18W - 20W LED tube light and Numbers 120.00 381.99 45838.80

fitting with all accessories.

20 20 Supply of inverter type 1x20W LED Light Numbers 30.00 799.00 23970.00

Fitting & LED Tube Complete Set. The tube

light shall be with auto cut feature on full

charge tube light and fitting with all

accessories. Battery back up 4 hour,

specification as per RDSO guidelines.

21 21 Supply of 9W LED based lamp with holder. Numbers 16.00 86.21 1379.36

22 22 Supply for drawing of service line in Metre 300.00 419.87 125961.00

concealed with 2 nos. 10 sq mm PVC

insulated multistrand copper conductor

cable & all wiring accessories.

23 23 Supply for drawing of main-service line in Metre 800.00 219.23 175384.00

concealed with 2 Nos. 6 sq. mm PVC

insulated multistrand copper conductor

cable & all wiring accessories.

24 24 Supply for drawing of sub-service line in Metre 1900.00 204.86 389234.00

concealed with 2 Nos. 4 sq. mm PVC

insulated multistrand copper conductor

cable & all wiring accessories.

25 25 Supply & installation of Drinking Water Set 1.00 137786.24 137786.24

Coolers With Built In Water Purification

26 26 Supply & testing of desert cooler 280 watt Numbers 6.00 9107.00 54642.00

with all accessories. The cooler shall be

Plastic Body Floor Standing with integral

caster wheels Mosquito Breeding feature.

27 27 Supply of 32A D.P. Main Switch With Key Numbers 16.00 524.57 8393.12

Ring Tag (Hotel room application).

28 28 Supply of occupancy sensor along with Numbers 14.00 5744.25 80419.50

required wiring with 4 sq. mm copper wire.

29 29 Supply of Heavy Duty BLDC Air circulator Numbers 8.00 10266.00 82128.00

fan 600 mm sweep, wall mounting type.

30 30 Supply of LED based 150W High bay light Numbers 10.00 11827.23 118272.30

luminaire with all accessories as per

PCEE/GRC's specification.

CKP-DIVN-ENGG/SOUTH EASTERN RLY

31 31 Supply of LED based 150W Flood light Numbers 14.00 7706.72 107894.08

luminaire with all accessories as per

PCEE/GRC's specification.

32 32 Supply of main earth with all accessories Numbers 30.00 2154.34 64630.20

as per Railway's drawing no. CEE/G/A3/P-

134 (Mod.1) & CEE/G/A3/P-150 (Alt.1).

33 33 Design, manufacture, display of wall Square 100.00 2836.97 283697.00

/hanging / floor mounting type LED Foot

illuminated sign / direction boards.

34 34 Supply of telescopic aluminium ladder 6 Numbers 2.00 11505.00 23010.00

mtr/ 15 steps or above, load capacity 150

KG minimum, EN131 certified.

Schedule D-Execution of Electrical(G) works (Erection items) Note :- This schedule to be read in

Schedule conjunction with the Technical Explanatory Note, General explanatory Note & mentioned

specifications. Type of wiring to be done : Concealed & Modular type.

Item- 1 Erection of Electrical items

S No. Item No Description of Item Unit Qty Rate Amount

1 1 Trenching and laying of different type Metre 890.00 183.19 163039.10

cables along the road and Railway track.

2 2 Erection of LT cable on pole/ wall by Metre 50.00 72.86 3643.00

proper bracketing arrangement at 50 cm

3 3 Trenching and laying of different type Metre 60.00 421.49 25289.40

cables across the road and Railway track.

with all accessories.

5 5 Erection of GI perforated type cable tray Metre 100.00 175.10 17510.00

made of standard length of 2.5 mtr with

all accessories.

6 6 Erection, testing & commissioning of 45 W Numbers 6.00 125.93 755.58

LED street light.

7 7 Erection, testing & commissioning of three Numbers 1.00 333.82 333.82

phase Astronomical timer panel.

8 8 Erection, testing & commissioning of LT Numbers 1.00 1794.79 1794.79

panel consist of 1 No.125 Amp 36 kA FP

MCCB as a incoming , 02 Nos. 63 Amp FP

MCCB as a outgoing and 32 A DP MCB-7

Nos. as a outgoing with cable termination.

9 9 Erection, testing and commissioning of Numbers 8.00 427.49 3419.92

SPN 18- way DB (DD) consisting of DP 63A

10 kA MCB - 1 no. as incoming and 6A -

16A 10kA SP MCB - 4 Nos, 20A - 32A 10kA

DP MCB - 4 Nos as outgoing.

10 10 Erection, testing & commissioning of split Numbers 8.00 2449.08 19592.64

Air Conditioner 2Ton with all accessories.

11 11 Point wiring in concealed (modular) for Numbers 350.00 451.35 157972.50

light, fan points by PVC insulated FRLSH

copper conductor cable of size 1.5 sqmm

along with all accessories and earthing

12 12 Erection, testing & commissioning of BEE Numbers 70.00 288.91 20223.70

Star Rated (5-star rating) AC ceiling fan of

1200mm sweep 230V, 50 Hz complete

with all accessories.

13 13 Erection, testing & commissioning of BLDC Numbers 16.00 288.91 4622.56

exhaust fan, 300 mm sweep 230V, 50Hz

complete with all accessories.

14 14 Erection, testing & commissioning of Numbers 30.00 86.22 2586.60

recess mounted Square panel (2 feet x 2

feet) Luminaire including wiring.

15 15 Erection, testing & commissioning of 18W - Numbers 120.00 43.98 5277.60

20W LED tube light and fitting with all

CKP-DIVN-ENGG/SOUTH EASTERN RLY

16 16 Erection, testing & commissioning of Numbers 30.00 43.98 1319.40

1x20W LED Light Fitting & LED Tube

Complete Set. The tube light shall be with

auto cut feature on full charge tube light

and fitting with all accessories.

17 17 Erection, testing & commissioning of 9W Numbers 16.00 43.98 703.68

LED based lamp with angular holder.

20 20 Wiring of multi-plug board for Computer Numbers 30.00 1126.63 33798.90

power points with a) Plug Socket 6Amp. - 3

nos. b) Switch 6 Amp - 3 nos. c) Plug

Socket 16 Amp. - 1 no. d) Switch, 16 Amp -

1 no. e) MCB 16Amp, B/cap-10KA. - 1 no. f)

LED indication lamp - 1no, including wiring

with 2.5 mm2 single core multi strand PVC

FRLSH copper conductor cable.

21 21 Erection for drawing of service line in Metre 300.00 46.85 14055.00

concealed with 2 nos. 10 sq mm & all

wiring accessories.

22 22 Erection for drawing of main-service line in Metre 800.00 37.20 29760.00

concealed with 2 nos. 6 sq mm & all wiring

23 23 Erection for drawing of sub-service line in Metre 1900.00 30.95 58805.00

concealed with 2 nos. 4 sq mm & all wiring

24 24 Erection, testing & commissioning of 32A Numbers 16.00 52.46 839.36

D.P. Main Switch With Key Ring Tag (Hotel

room application).

25 25 Erection, testing & commissioning of Numbers 8.00 671.58 5372.64

Heavy Duty BLDC Air circulator fan 600

mm sweep, 1300 RPM, WATT 120-140 ,

WALL mounting type.

26 26 Erection, testing & commissioning of 150 Numbers 10.00 786.74 7867.40

watt LED Gigh bay light with all

accessories. Specification of luminaire

shall conform to PCEE/GRC's latest

27 27 Erection, testing & commissioning of 150 Numbers 14.00 437.14 6119.96

watt LED Flood light with all accessories.

Specification of luminaire shall conform to

PCEE/GRC's latest specification.

28 28 Erection, testing & commissioning of main Numbers 30.00 1834.79 55043.70

earth as per Railway's drawing no.

CEE/G/A3/P-134 (Mod.1) & CEE/G/A3/P-150

29 29 Dismantling concrete kerb stones/ rail cum 2.00 602.64 1205.28

level platform stones /concrete beams

/slab/or similar light structural parts/stones

without appreciable damage including

stacking of serviceable material and

disposal of unserviceable material within

sand : 4 ballast)for make good of damage

due to work with supply of cement, sand &

ballast including labour.

31 31 Erection, installation and testing of Square 100.00 297.85 29785.00

wall/hanging/floor/pole mounting type LED Foot

illuminated, Modular, Changeable

Aluminium extruded profile

signage/direction board in full/half

Parabolic and Elliptical square and multi