REPAIR TO HIGH SECURITY FENCING STONE MASONRY WALL CATTLE FENCING PATH SECURITY FENCING AND MISC ITEMS IN A A BANAR UNDER GE BANAR

Amount

Dismantling posts or struts (RCC) any section, including taking out embedded portion in concrete and making good distrubed ground complete all as specified.

Restraining, resecuring including making good staples etc to barbed wire of any description and in any position complete all as specified.

S&F in repair Barbed wire, Galvanized steel, 2 strand 2.24 mm dia barbed with 2mm dia bars at 75 mm spacing straining and type of standard rails, straining bolt, including securing or tying at crossings with and provision of galvanized mild steel wire, staples or steel pins etc ( each line wire to be measured) complete all as specified.

Dismantling of wrought iron or mild steel work including of any description not otherwise provided for complete all as specified.

Excavating in post holes (or similar holes) each n.exc 0.50 Cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in hard/dense soil complete all as specified.

M & L for PCC (1:3:6) type C2 by using 40 mm well graded stone aggregate as in foundation, filling and mass concrete complete all as specified.

M&L for rolled steel section as in posts, struts and staples in fencing including cutting to top to shape (swan neck) as directed, drilling holes, notching for wire, etc flat iron fillets (for securing wire mesh etc) including all necessary bolting or riveting welding etc and similar work confirming to Fe-290 Gde-165 complete all as specified. Note :- Fencing posts should be painted before fixing

M&L for rolled steel section framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering, doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings including all necessary bolting or riveting welding etc and similar work confirming to Fe-290 Gde-165 complete all as specified.

M & L for two coats of synthetic enamalled paint over one coat of red oxide primer on new steel surfaces exc 100mm width or girth, including preparation of the surface complete all as specified.

Dismantling of fencing wire mesh any type and any size complete all as specified.

Supply only Chain link MS galvanised fencing, any size or type, complete all as specified.

Fixing only chain link fencing including line wires/ MS round bar (Any numbers), any mesh, size and type to any type of standards rails, straining bolts, etc including provision of binding wire (Note. Supply of flat iron, MS round bar & chain link shall be measured and paid seperately under supply only) complete all as specified.

S & F 12 mm dia MS screw bolts any size (machine made) with hexagonal or square heads at one end and screwed the other ends, fitted with washer and one one hexagonal nut exc 5cm long but n exc 10cm complete all as specified.

Supply only MS rounded bars Fe-290 (Gde-165) 10 mm dia and over cut to length and bend to shape as required as in tie bars, secured with nut, bolt and washers complete all as specified.

Demolition of Brickwork, PCC or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified.

M&L for squared rubble walling Jodhpur type regular course well bonded bedded and solidly hearted built in cement mortar 1:6 complete all as specified.

As as per Ser Item No 16 above but except stone complete all as specified.

Extra over on stone walling for hammer dressing to face stone with maximum depression on face from straight edge n.exc 20 mm and dressing faces beds and joints as specified to square rubble walling regular course Jodhpur type all as specified.

M&L for PCC (1:2:4) type B-1 using 20mm graded stone aggregate as in coping including necessary form work, weathering slightly rounded or chamferred angles and thoating complete all as specified.

Raking out joints/pointing to squarred rubble masonry, coursed or uncoursed built in cement mortar complete all as specified.

M&L for keyed pointing to stone masonry surface in CM 1:4 complete all as specified.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified.

Material and labour for 15mm thick rendering in CM 1:4 mixed with WPC on stone masonry surfaces finished even and smooth without using extra cement complete all as specified.

Supply only integral water proofing compound complete all as specified.

Material and labour for preparation of newly plastered surface of walls and applying two coats of cement base paint over one coat of alkali resistance primer complete all as specified.

M&L for one coat of cement base paint on old plastered/pointed surfaces of walls including necessary preparation of surfaces all as specified.

Demolition of cement concrete (unreinforced) in ground floors and pavings exc 15 cm thickness (below or above ground level) and removing from site complete all as specified.

M&L for 75mm thick PCC 1:4:8, type D2 (using 40mm graded stone aggregate) as in sub base complete all as specified.

M&L for Sand filling under floors or in foundation including watering and consolidation complete all as specified.

M&L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade with grey cement and pigment complete all as specified.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) and removing from site complete all as specified.

M&L for 25mm thick PCC 1:2:4, Type B-0 using 12.50mm graded aggregates as in base concrete to floor finish complete all as specified.

M&L for Chequered cement concrete tiles 20cmx20cmx25mm thick, set, jointed and pointed in neat cement slurry with grey cement and pigment in floors over and including 20mm thick screed bed in CM 1:4 complete all as specified.

M&L for Providing factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified.

POOJA CONSTRUCTION (BID ID -3045223)

NISHA CONSTRUCTIONS (BID ID -3049883)

Narendra General Suppliers (BID ID -3053952)

Bhawani Enterprises (BID ID -3049432)