Construction of Dr. Ayyappapanicker Memorial Foreign Language building,University of Kerala,Kariavattom Campus, Thiruvananthapuram (DSR 2018)

Amount

Site clearance

2.31 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

OD45642/2024-2025 Engaging Man labour for Cleaning

OD58370/2024-2025 Engaging JCB for earth cutting, removing root of the big trees and site leveling including rent labor charges, fuel, batá etc. complete

Earth work

2.6.1 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

2.26.1 Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

2.34.1 Supplying chemical emulsion in sealed containers including delivery as specified.Chlorpyriphos / Lindane emulsifiable concentrate of 20%

2.35.3.1 Diluting and injecting chemical emulsion for POST -CONSTRUCTIONAL antitermite treatment (excluding the cost of chemical emulsion): Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Cement concrete

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

4.17 Making plinth protection 50 mm thick of cement concrete 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

7.1.1 Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

Reinforced Cement concrete

OD63566/2024-2025 Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using cement content as per approved design mix, manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering, shuttering finishing and reinforcement including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in -charge. All work upto plinth level (modified)

OD63567/2024-2025 Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using cement content as per approved design mix, manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering, shuttering finishing and reinforcement including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in -charge. All work above plinth level upto floor V level (Modified)

5.44.1 Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor tofloor /floor to wall expansion control system for various vertical localtion in loadapplication areas that accommodates multi directional seismic movement without stress to it's components. System shall consist of metal profiles with a universalaluminum base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thicknessrequired to satisfy projects movement and loading requirements and secured tobase members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions. The Self – centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in-Charge . (Material shall confirm to ASTM 6063).Floor Joint of 100 mm gap.

5.45.1 Providing and fixing of expansion joint system related with wall joint (internal/ external) location as per drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per ASTM B221-02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall confirm to ASTM 6063).Wall Joint of 100 mm gap.

5.46.1 Providing and fixing of expansion joint system of approved make and manufactures for various roof locations as per approved drawings and direction of Engineer-InCharge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates asper ASTM B221-02. The system shall be such that it provides watertight roof to roof/roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s preengineered self-centering arrangement that freely rotates / moves in all directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement. Material shall confirm to ASTM 6063.Roof Joint of 100 mm gap.

5.29.2.1 Providing and fixing sheet covering over expansion joints with iron screws as per design. Aluminium fluted strips 3.15 mm thick150 mm wide

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.22A.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

Centering and Shuttering

5.9.1 Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2 Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3 Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.5 Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.6 Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.7 Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases)

Masonry works

50.6.1.2 Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement: 6 coarse sand) etc complete.

50.6.1.3 Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure above floor two level up to floor V level thickness 20cm and above in: CM 1:6 ( 1 cement :6 coarse sand) etc complete

50.6.1.8 Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in: CM 1:6 ( 1 cement : 6 coarse sand etc complete

50.6.1.9 Solid block masonry using pre cast solid blocks( Factory made) of size 40x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure above floor two level upto floor five level with thickness 15cm in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

50.6.3.2 Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete

6.13.2 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement : 4 coarse sand)

6.4.1 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in:Cement mortar 1:4 ( 1 cement : 4 coarse sand)

Wood works

9.1.1 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Second class teak wood

9.20.1 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of I st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

9.5.1.1 Providing and fixing panelled or panelled and glazed shutters for shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessery screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer - in-charge. Second class teak wood35 mm thick shutters

9.53 Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

9.7.1 Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured), Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick:Second class teak wood

9.7.7.2 Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured), Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick:5.5mm thick glass pane

OD46460/2024-2025 Providing and fixing bright finished Stainless Steel Tower Bolts (barrel type) with necessary screws etc. complete: 250 x 10 mm (9.74.1 modified)

OD46461/2024-2025 Providing and fixing bright finished Stainless Steel Tower Bolts (barrel type) with necessary screws etc. complete: 200x10 mm (9.74.2 modified )

OD46462/2024-2025 Providing and fixing GODREJ (or equivalent) Silver 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. (modified)

OD46468/2024-2025 Supplying and fixing 300 mm Ornamental brass type Door Aldrop

50.9.11.2 Providing and fixing Thomson Multi wood board or equivalent make paneling 18 mm thick, to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately)as per the direction of site Engineer-in-charge.

9.161 Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/m2) suita2ble for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m2 . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter . The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- charge (Cost of SS ball bearing hinges is excluded

9.162 Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (panelling to be paid for seperately

UPVC works

9.121 Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of crosssection 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminated shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.

9.122.2 Providing and fixing to existing door frames.30 mm thick Fiberglass Reinforced Plastic (F.R.P) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF) / Polystyrene foam to be used all filler material throughout the hollow panel, casted monoolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS : 14856, complete as per direction of Engineerin-charge

9.147B.1 543 SUB HEAD : 9 - WOOD & PVC WORK 9.147B Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

9.147D.5 Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Three track three panels sliding window made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 +/- 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm)

9.147D.3 Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 +/- 0.2 mm and single glazing bead / double glazing bead of appropriate dimension . (Area of window above 1.75 sqm upto 2.50 sqm).

Finishing works

13.1.1 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

50.13.1 9 mm cement plastering of mix : 1:3 (1 cement : 3 fine sand ) including all cost of materials, labour charges etc complete

13.9.1 Cement plaster 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of neat cement.12 mm cement plaster

13.48.1 Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm

13.48.2 Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.75 ltr/10 sqm of approved brand and manufacture

13.48.3 Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture

13.80 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

13.50.1 Applying priming coat:With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

13.68.1 French spirit polishing:Two or more coats on new works including a coat of wood filler

OD46464/2024-2025 Providing water cutting on the border of sunshade and roof slab projection in CM1:3,15mm thick and of 25mm wide including watering, curing, cost and conveyance of all materials and labour charges etc. complete

13.45.1 Finishing walls with textured exterior pint of required shade:New work (Two or more coats applied @ 3.28 ltr/ 10 sqm ) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm

Flooring works

11.41.3 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 800x 800 mm

11.46.3 Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 800 x 800 mm

11.48.2 Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 600x600 mm

OD58375/2024-2025 Providing and laying vitrified wall tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600 x 600 mm.

OD58376/2024-2025 Providing and laying vitrified Matte Finish floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600 x 600 mm.

11.48.3 Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 800x800mm

8.2.2.2 Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

11.20.3 Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand).Dark shade pigment using ordinary cement

Steel works

10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

10.26.1 Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approves steel primer.M.S. tube

10.28 Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

9.48.2 Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

OD45749/2024-2025 Providing & fixing Poly carbonate transparent crystal roof sheet 3 mm thick as approved by the Engineer in charge and should be supplied in a single length of 12 M or as decide by the Engineer in charge. The sheets shall be fixed using self drilling/ self tapping screw of size (5.5x55mm) with EPDM seal complete upto any pitch in horizontal / vertical / curved surfaces, but excluding the cost of purlins, rafters, trusses and including cutting to size and shapes where ever required.

OD59295/2024-2025 Providing precast Terracotta Jali including fixing and finishing in cement mortar 1:3 (1 cement : 3 fine sand ) etc. complete

10.6.1 Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thick top cover

10.7 Providing and fixing ball bearing for rolling shutters.

Aluminium works

21.1.1.2 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2.2 For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.17 Providing and fixing anodised aluminium grill ( anodised transparent or dyed to required shade according to IS : 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P brass/stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge.(Only weight of grill to be measured for payment ).

25.7 Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Alumini um sheets (each0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Glass works

21.3.2 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness

OD45750/2024-2025 Providing and fixing glazing in uPVC door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. With float glass panes of 5.50 mm thickness

OD53997/2024-2025 Supplying, Providing and fixing 12mm thick Toughened glass(Saint Gobain) Partition System with 40 x 20 mm or nearest size Stainless steel Profile and accessories, fixing to masonry or concrete, as per drawing /instruction of Engineer in charge .Including all cost and conveyance of materials, labour etc complete.

OD54009/2024-2025 Toughened Glass Door : Providing and fixing Double door (150 x240 cm) of 12mm thick Toughened glass door (Saint Gobain or Equivalent) with (Dormakaba or Equivalent) patch fittings (Floor Spring, Top patch, pivot Pin, Bottom patch, Corner lock, Handle- Dorma TGDIH 25 x 350 mm Stainless Steel 304 H-Type Glass Door Handle - Satin Finish ). Including all cost and conveyance of materials, labour etc. complete.

OD54010/2024-2025 Toughened Glass Door : Providing and fixing Double door (200 x240 cm) of 12mm thick Toughened glass door (Saint Gobain or Equivalent) with (Dormakaba or Equivalent) patch fittings (Floor Spring, Top patch, pivot Pin, Bottom patch, Corner lock, Handle- Dorma TGDIH 25 x 350 mm Stainless Steel 304 H-Type Glass Door Handle - Satin Finish ). Including all cost and conveyance of materials, labour etc. complete.

False Ceiling works

12.45.1 Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed towall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:12.5 mm thick tapered edge gypsum plain board conforming to IS : 2095-Part 1

OD48608/2024-2025 Providing and fixing Gypsum Step ceiling with width/ depth less than or equal to 300 mm as per approved design.Frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 ,ie, perimeter channels 0.5 mm thick 27 mm high having flanges of 20 and 30 mm long to be fixed as per design intent and 12.5 mm thick tapered edge gypsum plain board to be fixed on to the framework using 25 mm long drywall screw.Finish the joints using jointing compound and joint tap as per manufacture specification.Including cost and conveyance of all materials labor charges etc.complete as per direction of Engineer-in-charge. The visible Vertical Sides will be measured .

Waterproofing work

22.5 Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

PHE works

17.1.1 Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm Sand Cast Iron P or S trap, 10 litter low level white P.V.C.flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever require:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

OD59162/2024-2025 Providing and Fixing sanitary fixtures for handicapped toilet including one number Extended wall mount closet with soft close seat cover and cistern one wash basin, one pair mounting brackets, one number elbow operated pillar cock and all other related fittings like waste coupling one number hinged rail 76 cm and 4 no's of grab rails 60 cm etc designed for people with special needs comes with as per manufactures specification including cutting and making good the walls and floors wherever required as per drawing and as directed by engineer in charge.

17.3.1 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid

17.4.1 Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I. clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required:One urinal basin with 5 litre white P.V.C. automatic flushing cistern

17.7.2 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630 x 450 mm with a single 15 mm C.P. brass pillar tap

17.7.4 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap

17.81 Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.

OD45754/2024-2025 Providing and fixing Soap Dish Holder(jaguar item code ACN-CHR-1131N or equivalent)

OD45756/2024-2025 Supplying and fixing PVC Floor Trap 100mmx75mm size without Jali including cutting open, fixing through RCC slabs and making good the damages.

OD45757/2024-2025 Providing and fixing SS grating of approved quality. Rectangular type with openable circular lid : 150 mm nominal size square 100 mm diameter of the inner hinged round grating

18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank :ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

50.17.1.5 Supplying and fixing CP Health Faucet superior quality ( Jagur or equvalent make ) including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore

18.49.1 Providing and fixing C.P brass bib cock of approved quality conforming to IS: 8931.15 mm nominal bore

18.51.1 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore

18.52.1 Providing and fixing C.P brass stop cock ( concealed) of standard design and of approved make conforming to IS: 893115 mm nominal bore

50.18.8.3.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 25 mm pipe 12 kgf/cm2

50.18.8.4.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 32 mm pipe 10Kgf/cm2

50.18.8.6.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 10 kgf/cm2

50.18.8.7.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work including cutting chases and making good the wall etc. 63 mm pipe 6 Kgf/cm2

50.18.8.8.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 75 mm pipe 6 Kgf/cm2

50.18.8.9.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc. 110 mm pipe 6kgf/cm2

50.18.9.10.1 Providing and fixing PVC pipes includings jointing of pipes with one step pvc solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in Charge. 150 mm dia 6 Kgf/cm2

50.18.9.13.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 25 mm dia 12 Kgf/ cm2- External work- exposed on wall

50.18.9.15.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 40 mm dia 10Kgf/cm2- External work- Exposed on wall

50.18.9.17.1 Providing and fixing PVC pipes including fixing the pipe with clamps/ clip at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 63 mm dia 6 Kgf/cm2 - External work - Exposed on wall

50.18.9.19.1 Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall

50.18.9.20.1 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Elbow

50.18.9.20.2 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -63 dia 45 degree Elbow

50.18.9.20.4 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Bend

50.18.9.21 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Elbow

50.18.9.21.2 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75 mm dia 45 degree Elbow

50.18.9.21.3 Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75 mm dia Door Elbow

50.18.9.21.4 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Bend

50.18.9.22.1 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Elbow

50.18.9.22.11 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 110 mm dia Socket/ coupling

50.18.9.22.2 Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia 45 degree Elbow

OD49231/2024-2025 Providing and Fixing PVC moulded fittings / accessories for Rigid PVC pipes including jointing with PVC solvent cement - 110 mm dia Y

50.18.9.22.3 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement-110 mm dia Door Elbow

50.18.9.22.4 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia Bend

50.18.9.22.5 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes including jointing with PVC solvent cement 110x110x110 mm dia Tee

50.18.9.22.6 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x110x110 mm dia Door tee

50.18.9.22.7 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x110x75 mm dia Door Tee

50.18.9.22.8 Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia Vent cowl

50.18.9.5.1 Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching refilling & testing of joints complete as per direction of Engineer in Charge 40 mm dia 10Kgf/cm2

50.18.9.9.1 Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2

OD46383/2024-2025 Constructing silt pit 20 x 20cm up to 60 cm depth inside dimension in half brick thick walls in CM all-round over brick jelly concrete in CM 1:3 for foundation 15 cm thick, plastering with CM 1:3, 12 mm thick with neat cement flushing coat, etc. complete including providing 2 nos. heavy CI gratings, 150 x 150 mm and 180 x 180 mm for the inside and outside , painted with black Japan two coats and necessary earth work excavation etc. complete.

OD46384/2024-2025 Providing and fixing in position C.P towel rail, including cost of all materials ( wooden plugs, steel screws etc.) and labour charges etc. complete. Make: Jaquar / Hind ware / Parryware / Equivalent etc.

OD46385/2024-2025 Constructing and providing RCC manhole 50 x 50 x 45cm inner dimension including earth work with 30 cm work clearance PCC 1:4:8 using 40 mm metal 10 cm thick for base RCC 1:2:4 using 20 mm metal for 20cm thick for sides and 10 cm thick base with 11 cm thick pre cast cover provision for inlet and out let connection forming channels in cc 1:3:6 at bottom, plastering with flush coat inside cutting groove for cover slab ,handling grip using 12 mm bar etc complete

OD46386/2024-2025 Constructing and providing RCC manhole 75 x 75 x 120cm inner dimension including earth work with 30 cm work clearance PCC 1:4:8 using 40 mm metal 10 cm thick for base RCC 1:2:4 using 20 mm metal for 20cm thick for sides and 10 cm thick base with 11 cm thick pre cast cover provision for inlet and out let connection forming channels in cc 1:3:6 at bottom, plastering with flush coat inside cutting groove for cover slab ,handling grip using 12 mm bar etc complete

OD46387/2024-2025 Constructing and providing RCC manhole 60 x 60 x 90cm inner dimension including earth work with 30 cm work clearance PCC 1:4:8 using 40 mm metal 10 cm thick for base RCC 1:2:4 using 20 mm metal for 20cm thick for sides and 10 cm thick base with 11 cm thick pre cast cover provision for inlet and out let connection forming channels in cc 1:3:6 at bottom, plastering with flush coat inside cutting groove for cover slab ,handling grip using 12 mm bar etc complete

17.32.4 Providing and fixing mirror of superior glass ( of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 1500x450 mm

OD59293/2024-2025 Supply and fixing C I Cover with frame for manholes 600 x 600 mm C I cover (Light duty) the weight of the cover 32 kg

Over head Tank

5.9.2 Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3 Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.5 Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.6 Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

OD64593/2024-2025 Providing and laying in position machine batched and machine mixed design mix M- 25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. All work above plinth level upto floor V level (Modified)

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

13.7.1 12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand)

13.21 Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

22.24 Providing and applying integral crystalline (dry shake) of hydrophilic in nature for waterproofing treatment to the RCC structures like basement raft, foundation slab,sewage & water treatment plant slab, warehouses floor, parking structures and water tank base slab etc. sprinkled @0.60kg per sqm or higher as recommended by the manufacturer's specification over the lean concrete of above cited structures. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e. by reducingpermeability of concrete by more than 85%, compared control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline dry shake shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the Engineer-incharge. The product performance shall carry guarantee for 10 years against any leakage.

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

OD64594/2024-2025 Providing and laying in position machine batched and machine mixed design mix M- 25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. All work upto plinth level (Modified)

5.9.1 Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2 Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3 Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.5 Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

13.1.1 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.21 Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers

13.9.1 Cement plaster 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of neat cement.12 mm cement plaster

50.13.1 9 mm cement plastering of mix : 1:3 (1 cement : 3 fine sand ) including all cost of materials, labour charges etc complete

Septic Tank work

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

2.26.1 Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

OD64595/2024-2025 Providing and laying in position machine batched and machine mixed design mix M- 25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. All work upto plinth level (Modified)

5.9.1 Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2 Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3 Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.5 Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

OD45765/2024-2025 Water proof plastering with Cement Mortar 1:4 (1 cement : 4 fine sand) 12mm thick plaster finished with a floating coat of neat cement mixed with water proofing compound of approved make @ 2kg/m2 of mix floated hard and troweled smooth including all labour, material, conveyance charges etc complete

OD45766/2024-2025 Supplying and fixing 1.20 m dia, 5 cm thick, 30 cm depth pre cast cement concrete ring including necessary earth work excavation, erection cost and conveyance of all materials and labour charges etc., complete, ( MR for 1 ring )

Yard Work

OD45767/2024-2025 Providing and laying 80 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge. (modified)

16.69 Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature jointed with cement mortar 1:3 ( 1 cement : 3 coarse sand) , including making joints with or without grooves ( thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge ( length of finished kerb edging shall be measured for payment ). ( Precast C.C. kerb stone shall be approved by Engineer-in-Charge)

Exterior Modification

13.73.2 Forming groove of uniform size in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer, including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and directions of the Engineer-in-Charge:20 mm wide and 15 mm deep groove

OD46204/2024-2025 Providing and fixing Ist quality cladding tile (thickness to be specified by the manufacturer), of approved make, in all colours, shades of any size as approved by Engineer -in-Charge, laid with on polymer modified adhesive mortar, including weather sealant, stainless steel (Grade 304) Frame at 3 meter intervals. etc., complete.

Road Work

4.9 Wet Mix Macadam <br> Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared subbase and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification Clause 406. <br> By Mechanical Means with 1 km lead

3.5.2 Excavation in Soil with Dozer with lead upto 100 m <br> Excavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 m, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections.

5.1.2a Prime Coat <br> Medium porosity :- Providing and applying primer coat with Bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.90- 1.2 kg/sqm using mechanical means as per Technical Specification Clause 502.

5.12.A.1.2a Seal Coat - Manual Means - Type A - Bitumen S-65 <br> Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510 <br> A. By Manual Means :- Case - I : Type A <br> (II) Bitumen (S-65)

5.2.3a Tack Coat <br>Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503.

5.9.1.2a 20mm thick Open-Graded Premix Carpet using Bituminous (penetration grade/modified bitumen) Binder - Bitumen S-65 <br> Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508. <br> Case - I By Manual Means <br> (II) Bitumen (S-65)

OD58393/2024-2025 Painting road surface marking with adequate nos of coats to give uniform finish with ready mixed road marking paint conforming to IS: 164, on bituminous surface in white / yellow shade, including cleaning the surface of all dirt, scales oil, grease and foreign material etc. complete. New work (Two or more coats)

OD58394/2024-2025 Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and rerolling the sub grade and disposal of surplus earth with lead upto 50 metres.

10.14 Tubular Steel Railing on Medium Weight Steel Channel (ISMC series) 100 mm x 50 mm <br> Providing, fixing and erecting 50 mm dia steel pipe railing in 3 rows duly painted on medium weight steel channels (ISMC series) 100 mm x 50 mm, 1.2 m high above ground, 2 m centre-to-centre, complete as per approved drawings Clause 1706

OD59294/2024-2025 Construction of footpath/ separator by providing a 150 mm compacted Granular sub base material as per clause 401 and 25 mm thick cement concrete grade M15, over laid with precast concrete tiles in cement mortar 1:3 including provision of all drainage arrangements but excluding kerb channel.

Internal Electrification

1.10.1 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group A

1.10.2 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group B

1.10.3 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

1.11 Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required

1.55.2 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group B

1.55.3 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C

1.17.3 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 X 1.5 sq.mm

1.17.12 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 2.5 sq. mm

1.17.21 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 4 sq. mm

90.6.4.54 Supply and drawing 650/1100 V grade FRLS PVC insulated stranded single core copper conductor cables conforming to IS 694 part I 1990 in the existing surface / recess conduit as required including giving necessary connections of the following sizes.10.00 sq.mm 4 Run

1.21.1 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.21.2 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.21.3 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.32 mm

1.24.3 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

1.24.5 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

1.56 Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providng and fixing 2 Nos. 3 pin 5/6 A modular socket outlets and 2 Nos. 5/6 A modular switches, connection etc. as required. (For light plugs to be used in non residential buildings).

1.24.8 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.Bell push

1.25 Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

1.26 Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required

90.4.1 Supply and installation of suitable size MS rod type fan clamp in the RCC slab as per IS 732 as required.

1.33 Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

1.31 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

1.58 Supplying and fixing PVC batten/ angle holder including connection etc. as required.

1.27.2 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

1.41 Installation, testing and commissioning of pre - wired, fluorescent fitting/ compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq.mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

1.50.1 Installation of exhaust fan in the existing opening, including making good the damage connection testing, commissioning etc. as required.Upto 450 mm sweep

2.10.1 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

2.10.4 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole

OD44899/2024-2025 Supply and installation of the following MCB's (C curve) suitable for 50 Hz , AC supply conforming to IS 8828-1995/ IEC 60898 of the following current ratings in the existing enclosure and giving connections as required - 63A Triple Pole MCB

2.13.1 Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.13.2 Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.15.2 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residualcurrent circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.15.3 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.2.2 Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.125 Amp,16 KA,TPMCCB

90.11.1.10 Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required4 way (8+12) - three phase double cover (IP 42/43)

90.11.1.11 Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required6 way (8+18) - three phase double cover (IP 42/43)

90.11.1.12 Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required8 way (8+24) - three phase double cover (IP 42/43)

90.11.1.14 Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required4 way (8+12) - double cover TPN vertical DB with provision for fixing 4P MCB / Isolator/ RCCB/ RCBO as incomer and SP/ TP MCB as outgoing (IP 42/43)

90.11.1.19 Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required6 way (8+12) - double cover TPN vertical DB with provision for fixing MCCB as incomer and SP/ TP MCB as outgoing (IP 42/43)

90.11.1.20 Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required8 way (8+12) - double cover TPN vertical DB with provision for fixing MCCB as incomer and SP/ TP MCB as outgoing (IP 42/43)

90.12.7.41 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 16 sq mm with factory made clamp

90.12.1.30 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil).3.5 core 70 sq mm

90.12.1.32 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil).3.5 core 120 sq mm

90.12.1.34 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil).3.5 core 185 sq mm

90.12.6.24 Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.3 core 240 sq mm

90.12.6.30 Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.3.5 core 70 sq mm

90.12.6.32 Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.3.5 core 120 sq mm

90.12.6.34 Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.3.5 core 185 sq mm

90.12.6.36 Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.3.5 core 300 sq mm

90.12.7.27 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 25 sq mm with factory made clamp

90.12.7.28 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 35 sq mm with factory made clamp

90.12.7.29 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 50 sq mm with factory made clamp

90.12.7.30 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 70 sq mm

90.12.7.32 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 120 sq mm

90.12.7.34 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 185 sq mm

90.12.7.40 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 10 sq mm with factory made clamp

9.1.20 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X25 sq.mm (28mm)

9.1.21 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 35 sq. mm (32mm)

9.1.22 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 50 sq. mm (35mm)

9.1.25 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 120 sq. mm (45mm)

9.1.27 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 185 sq. mm (57mm)

9.1.29 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 240 sq. mm (62mm)

9.1.30 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 300 sq. mm (70mm)

9.1.32 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)

9.1.33 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)

90.16.3.9 Supply and clamping the following size of strips on surface of wall/ parapet/ existing cable tray using clamps fabricated from 20 X 3 mm GI flat duly painted or heavy duty GI spacer saddles spacing of clamps not exceeding 1 m, making good the damages, colour washing etc. as required ( for horizontal run)25 x 3 mm copper strip

90.16.1.3 Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required3.15 mm copper conductor ( 10 SWG)

90.16.1.4 Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required4.00 mm copper conductor ( 8 SWG)

90.16.5.3 Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.3.15 mm (10 SWG)

90.16.5.4 Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.4.00 mm (8 SWG)

OD44989/2024-2025 Earthing with G.I. earth plate 1200 mm X 1200 mm X 12 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

90.3.10 Supplying and providing extra H.G conduit down rod of 19 mm dia 2 x 1.00 m long with 16/0.20 mm 3 core copper conductor flex wire conforming to relevant ISS or with the extended original wiring and giving connection etc. as required.

OD45017/2024-2025 Supply, fabrication and fixing cable trays, supports etc. using angle iron and flats including painting using 2 coats of synthetic enamel paint over zinc chromate metal primer

90.3.15 Conveyance, installation, testing and commissioning of post-top lantern/ outdoor type FTL/ CFL fittings of all types directly on the existing pipe/ pole and giving connections with the existing wiring etc as required

90.5.1.3 Supply and fixing the following types of superior quality 250V A.C call bell on existing M.S. box and giving connections with required length of 3 core, 16 / 0.20mm 650/1100V grade PVC insulated and PVC sheathed round copper conductor flex wire conforming to relevant ISS or with the extended original wiring, earthing the MS box and making good the surface as required.Ding dong bell

90.5.1.4 Supply and fixing the following types of superior quality 250V A.C call bell on existing M.S. box and giving connections with required length of 3 core, 16 / 0.20mm 650/1100V grade PVC insulated and PVC sheathed round copper conductor flex wire conforming to relevant ISS or with the extended original wiring, earthing the MS box and making good the surface as required.Musical bell with bird sound

90.3.11 Conveyance, installation, testing and commissioning of surface mounting down light fittings of all types directly on ceiling including giving connections with required length of 16/0.20 mm 3 core round copper conductor flex wire conforming to relevant ISS or with the extended original wiring, making good the damages, colour washing etc as required.

90.3.23.5.3 Surface mounting decorative fluorescent tube light fitting complete with lamp with complete accessories duly wired up for use on 230 V AC .Surface mounting LED 20W LED Batten with out put 2000 lumen for use on 250V AC supply.

90.3.12 Conveyance and fixing charges of recess mounting down light fittings of all types complete with all accessories in the existing opening of false ceiling, giving connections with the existing wire etc., as required.

OD44991/2024-2025 Supply and providing of 15W Surface Mounted LED light having system efficacy<90lumen per watt, pf>.95, THD<10, CRI>=80, CCT 4000K, Ripple<5%,<br>ROHS Complaint, LM80, UGR <= 23%,IEC Compliant (Make <br>Philips/Wipro/Lighting Solutions

OD44990/2024-2025 Supply and providing of 28W Recess Mounted LED light in aluminium die cast housing ,polycarbonate optic material having system efficacy< 90 lumens per watt, pf>.95, THD<10, CRI>=80, CCT 4000K, Ripple<5% , ROHS Complaint, LM80, UGR <= 23%,IEC Compliant ( Make: Philips/Wipro/Lighting Solutions)

OD44992/2024-2025 Supply and providing of 18 W/20W Recess Mounted LED light in aluminium die<br>cast housing ,polycarbonate optic material having system efficacy< 90 lumens per watt, pf>.95, THD<10, CRI>=80, CCT 4000K, Ripple<5% , ROHS Complaint, LM80, UGR <= 23%,IEC Compliant ( Make: P h i l i p s / W i p r o / L i g h t i n g < b r > S o l u t i o n s )

OD44993/2024-2025 Supply and providing of 9 W Recess Mounted LED light in aluminium die cast<br>housing ,polycarbonate optic material having system efficacy<90 lumens per watt, pf>.95, THD<10, CRI>=80, CCT 4000K, Ripple<5% , ROHS Complaint,<br>LM80, UGR <= 23%,IEC Compliant ( Make: Philips/Wipro/Lighting Solutions

OD44994/2024-2025 Supply and providing of 40W LED Batten in surface/ suspended mounting, Ingress protection of IP20, Integrated batten in aluminium extruded housing having color temperature of 4000K,THD <10%,CRI>70 ,Internal surge protection of 4KV,50000 burning hours, Operating Temperature: -10 degree to 50 degree, Luminaire efficacy < 90 Lumens/Watts (Model: Crompton/Havells/Philips/Lightin>g Solutions)

OD44995/2024-2025 Supply and providing IP 65 rated LED Post Top of 20W having color temperature of 4000K,THD <10%,CRI>70,comprises of die cast capsule which comprises by die cast housing and PC cover, protection against surge for improved & trouble free luminaire life

OD44996/2024-2025 Supply and providing 10W Up& down Light having IP65 protection, color temperature of 4000K,total lumen output of fixture -670,class II protection, die casted aluminium

OD44997/2024-2025 Supply and fixing 1ft length LED mirror light of 5W ,decorative ultra slim polycarbonate LED fixture having color temperature of 4000K,plastic material construction. ( Make; Philips,Crompton,Havells,Bajaj)

OD44998/2024-2025 Supply and providing 9W LED bulb in the existing batten holder . (Make: Philips/Wipro/Bajaj/Havells/Crompton)

OD44999/2024-2025 Supply and providing of 10W LED Bulk head having IP66 high ingress protection, impact resistant- IK09, color temperature 4000K and lumen packs - 700lm/1100lm,pressure diecast housing with robust polycarbonate cover ,long l i f e t i m e o f 5 0 0 0 0 h r s . ( M o d e l - P h i l i p s E n d u r a L E D ) ( P h i l i p s / H a v e l l s / C r o m p t o n / B a j a j )

OD45000/2024-2025 Supply, installation, testing and commissioning of 400mm sweep wall fan with energy efficient BLDC motor ,giving connection etc complete as required

OD45018/2024-2025 Supply, installation, testing and commissioning of 200mm size PVC shuttered type exhaust fan with energy efficient BLDC motor, high air delivery, giving connection etc complete as required.( Havells/Crompton/ Usha/ Almonard)

OD45019/2024-2025 Supply,installation,testing and commissioning of 1200mm sweep, BEE 5 star rated ceiling fan with Brushless Direct Current ( BLDC) motor, class of insulation:B,3 nos blades,30cm long down rod,2 nos canopies, shackle kit, safety rope,copper winding,power factor not less than .9,service value (CMM/W) minimum 6.85,Air delivery 215 CMM,350RPM(tolerance as per IS 374-2019),THD less than 10%,remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts,washers,temperature,rise=75 degree C (Max),insulation resistance more than 2 mega ohm, suitable for 230V,50Hz,single phase AC supply ,earthing etc complete as required. (Model:Atomberg Renesa+ or equivalent )

90.15.4.5 Supply Conveyance, installation, testing and commissioning of 40W LED Flood light output greater than 105lumen/W 4000-6000 K with IP 66 protection LED Chip make Cree/Lumilled/Nichea with power factor greater than 0.95 at full load, internal surge protection up to 8 KV,and Aluminium pressure die-cast Powder coated housing, acrylic cover complete with THD less than10%, power factor greater than 0.98, RoHS compliant, duly wired up for use on 230 V AC supply. Driver compartment should be seperatly accessible for maintenance (LM 79&80 certificates from NABL accredited Third party lab to be produced mentioning chip manufacturer)

90.15.4.6 Supply Conveyance, installation, testing and commissioning of 70W LED Flood light output greater than 105lumen/W 4000-6000 K with IP 66 protection LED Chip make Cree/Lumilled/Nichea with power factor greater than 0.95 at full load, internal surge protection up to 8 KV,and Aluminium pressure die-cast Powder coated housing, acrylic cover complete with THD less than 10%, power factor greater than 0.98, RoHS compliant, duly wired up for use on 230 V AC supply. Driver compartment should be seperatly accessible for maintenance (LM 79&80 certificates from NABL accredited Third party lab to be produced mentioning chip manufacturer)

OD45021/2024-2025 Supply installation testing and commissioning 3Amps Led driver for the 6W LED Strip.

OD45022/2024-2025 Supply and Providing 6W LED Strip, giving connection etc complete as required.

90.3.17.2 Supply, conveyance and erection of the following sizes of 'B' class GI pipe in single section for post top lantern of all types on concrete base (excluding charges for concrete base and excavation) and painting with 2 coats of synthetic enamel paint over a coat of zinc chromate primer etc. as required.40 mm dia GI pipe

90.9.2.1 Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.100 x 50 mm CMS with base and lid

90.9.2.3 Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.External angle 90 degree

90.9.2.8 Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.End cap

OD63572/2024-2025 Supply and installation of Commercial Water purifier with 65 L storage capacity , Stainless Steel Housing, Brass -Chromium plated Faucets, Any combinations of Reverse Osmosis /Ultraviolent /Ozone, Separate outlet for normal, cold & hot water.

OD63577/2024-2025 Supply and installation of Sanitary Napkin Incinerator with Powder coated steel body, Burns 150 to 200 napkins per day, can be programmed for cycles/day, Ash collection tray for easy cleaning, Automatic temperature maintenance, Auto power off, Auto thermal cut-off for safety of user, Ceramic insulation for excellent thermal protection, Wall mountable. ( make. HLL or equivalent)

ELV Works

OD45032/2024-2025 Supply, Installation, testing and commissioning of 20 KVA 3 phase online DSP control IGBT Based double conversion UPS with Inbuilt isolation transformer 2Input Specification "DC Voltage Range"240VDC AC Voltage Range 330- 470VAC Connection3 Phase Frequency Range" 50Hz 5%" Harmonics distortion-<5% Power Factor0.97 to 0.99 rectifier IGBT Maximum Short Circuitwithstand lcc- 10kA Protection Switch and fuse ,3Output Specification Voltage Range230VAC+/- 1%, Connection1 Phase, Frequency Range 50Hz 5%, Harmonics distortion<3% at 100% linear load, Power Factor0.8, Output Voltage tolerance+/- 1%, Over Load capacity110% for 1 minutes, Effeciency93% or above, 4Regulation, Steady State1% of normal input, Recovery Time40 milliseconds, 5Frequency Range, Sync Window0.5Hz to 3Hz (synchronized to input), Free Running1%, Power factor0.8 lag for specified regulation and rating, Efficiency Normal 85- 90%, 6Voltage Distortion, Linear Load 3%THD, Non-Linear Load 5% THD, Technology Digital Signal Processor based IGBT Technology, Device sued IGBT, Crest Factor 3: Protections Input/output Low & High Output, Overload, 7Audible Warning, Visual Indication Input, By pass, Output overload, Battery Load, LCD Display Input Voltage, Output Voltage, Output load & Voltage, 8Bypass Specification, Static Bypass Required -with Zero Break Time, Connection1 Phase, Frequency Range50Hz 5%, Maximum Short Circuit with stand lcc-lOkA, Over Load Ca aci110% continues, Maximum Bypass Voltage230+/-1%, 9Battery Specification BATTERY TYPECPRI Certified Tubular of make exide/amaron/Equivalent Online UPS Battery with 3Years OEM Replacement Warranty, Charging Power 2% to 15% of UPS Capacity, Maximum Charging Power800w, Ripple Current<2%, Back up time, Battery ah and Quantity150 Ah ,20 nos , Battery stands 2 Nos. Lithium Ion Battery Compatibility Required, 10ProtectionShort circuit. input under and over voltage , over current, over load, over temperature, 11Standard i)ISO 90001:2015,14001:2015,OHAS 18001:2007 ii)CE:IEC/EN 62040-1 ;IEC/EN 62040=2;IEC/EN 62040=3 12Others Isolation Inbuilt Galvanic Isolation Transformer Certifications ISO 90001:2015,14001:2015,OHAS 18001:2007 TemPerature0 Degree Celsius to 45 degree Celsius Humidity 5 % to 9 5 % Audible Noise 45dBA Communication RS232 13Guaranty/Warranty 1) UPS3 Years with Components 2) Battery3 Years OEM replacement

OD45033/2024-2025 Supply ,installation, testing and commissioning of LCD Projector with Projection Technology RGB liquid crystal shutter projection system (3LCD<br>LCD Size :0.59” (C2fine)<br>Native Resolution WXGA<br>Lamp Life : (Normal /Eco)6,500 / 17,000 hours<br>Aspect Ratio04:03<br>Projection Lens - Type :Optical Zoom (Manual) / Focus (Manual)<br> F-Number : 1.51 – 1.99<br>Focal Length : 18.20 – 29.20 mm<br>Zoom Ratio : 1 – 1.6<br>Throw Ratio : 1.38 – 2.24 (Wide to Tele)<br>Brightness4,200 lumens<br>Contrast Ratio16,000:1<br>Internal SpeakersMonoaural: 16W x 1<br>Connectivity - Analog Input : D-Sub 15Pin , Composite, Digital Input : DVI-D, HDMI ,HDBaseT Output Terminal :DSub 15Pin, HDMI Audio Input : 2RCA (White & Red) , Stereo Mini Audio Output :Stereo Mini Jack<br>Others - USB Type A :(for Wireless LAN, Firmware Update, Copy OSD Settings)<br> USB Type B : (for Firmware Update, Copy OSD Settings Mic Input Stereo Mini Network Wired LAN, Wireless<br>Direct Power On / Off Yes Warranty Two years for Projector, One year for Lamp. ( Make: Epson,Sony ,Benq)

OD45034/2024-2025 Supply,installation,testing and commissioning of Motorized wall mount projection screen 5 x7 (Make: Logic )

OD45035/2024-2025 Supply,installation,testing and commissioning of 50 inch Ultra 4K LED Smart TV ,giving connection etc complete as required.( Make: Samsung/Sony)

OD45036/2024-2025 Supply, Installation, Testing and Commissioning of Wi-Fi 6 Ceiling Mount PoE Access Point (IEEE 802.11ax) Dual Band router speed upto 1.5 Gbps with DHCP server, PoE Port, including Device Interfaces 3 x Gigabit Ethernet LAN ports, 1 x Gigabit Ethernet WAN port, 1 x WPS button, 1 x power connector, Antenna Type Four external antennas, Wi-Fi Data Rate 2.4 GHz Up to 300 Mbps, 5 GHz Up to 1201 Mbps, IEEE Standard IEEE 802.11ax/ac/n/g/b/k/v/a/h, IEEE 802.3u/ab, Network Interface Card, Cable/DSL modem or other ISP equipment with Ethernet port, WAN Interface Static IP, Dynamic IP, PPPoE, PPTP, L2TP, DS-Lite, Support 802.1p & 802.1q VLAN tagging and Priority bit, Concurrent session: 30000 Functionality, Security Protocol WPA2 (Wi-Fi Protected Access), WPA3(Wi-Fi Protected Access), WPS (Wi-Fi Protected Setup), Firewall DoS, Stateful Packet Inspection, Anti-spoofing Checking, IP/MAC Address Filtering, 1 x DMZ with minimum 3 years onsite warranty.

OD65660/2024-2025 Supply, Installation, Testing and Commissioning of WLAN Controller with •Upto 100 or higher Access Points management with necessary license, Min 1 or more 1GbE RJ45 Port, Min 1 RJ45/Serial Console Port or Dedicated Management Port, Min 1 USB Port , Compatible with 802.11ac Wave 2 and 802.11ax access points, Multi-tenant with different sites / locations, Layer 2 & Layer 3 discovery of Access Points, Mobile APP based provisioning / configuration, Template / Profile based configuration, SSID, VLAN, Band, Channel Width, Security, Scheduling, MAC/IP Access Control, Guest Wi-Fi, User Authentication, RF / Bandwidth optimization, WMM, 20/40/80/160 Coexistence, IGMP Snooping, Spanning Tree, Multicast Bandwidth Control, Bandwidth Optimization – Client/SSID/Band , Internal / External Captive Portal with Radius Auth, WPA 2 and WPA3 Personal & Enterprise, Enhanced Open, Encryption Type (Auto/AES/TKIP), Primary and Backup Radius Servers config, SSL Certificate, Hotspot 2.0, Payment Gateway , Access Point - status, IP address, MAC address, channel, network, firmware version, Wireless Client - IP address, MAC address, authentication type, channel, associated SSID , •Offered Brand should be OEM / ODM, Access Points and WLC should be from single OEM with minimum 3 years onsite warranty.

OD45037/2024-2025 Supply, Installation, Testing and Commissioning of L2+ 24 port 10/100/1000Mbps PoE+ Switch meets IEEE standards 802.3, 802.3u, 802.3ab, 802.3x, 802.1Q, 802.1p, 802.1D and 802.1ad , PoE Power budget 190 Watts or above, with 48 Gbps throughput in full duplex mode having port based VLAN with 2 or more SFP uplink ports, rack mountable switch with minimum 3 years onsite warranty.<br>Approved Make HP, Netgear. Ruckus, Brocade,juniper,Cisco or equivalent

OD45983/2024-2025 Supply, Installation, Testing and Commissioning of duplex optical transceiver, eSFP, GE, Single-mode module suitable for the above switch with necessary LC/UPC pigtails/patch chords of molex make,LIU box and including splicing and termination as required

1.21.2 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.53.1 Supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required1 run of Cable

OD45984/2024-2025 Supply and fixing casing and capping of reputed brand (Legrand/ precision/ press fit) with ISI mark. 32 mm

OD45985/2024-2025 Supply and fixing casing and capping of reputed brand (Legrand/ precision/ press fit) with ISI mark. 25 mm

OD45986/2024-2025 Supply & Connecting LSZH 2 Mtr CAT-6 Giga UTP patch cord. Approved Make: Actassi, Belden, Molex, R&M, Commscope or equivalent

OD45987/2024-2025 Supply & Connecting LSZH 1Mtr CAT-6 Giga UTP patch cord. Approved Make: Actassi, Belden, Molex, R&M, Commscope or equivalent

OD45988/2024-2025 Supply and fixing 50 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required. Accessories including External Angle 90°, Flat Angle 90°/TEE, Internal Angle 90°, Internal Coupler, Flat cross,End Cap, Flanged Coupler, Joint cover, Cable Retainer, Wall plate for internal angle etc. Preferred Make: OBO, MK, Legrand or equivalent

OD45989/2024-2025 Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.Accessories including External Angle 90°,Flat Angle 90°/TEE,Internal Angle 90°, Internal Coupler,Flat cross,End Cap,Flanged Coupler, Joint cover,Cable Retainer,Wall plate for internal angle etc. Preferred Make: OBO, MK, Legrand or equivalent

OD45990/2024-2025 Supply and fixing of UL certified CAT-6 Information Outlet for 1000Mbps having spring shutter / dust cover face plate with one number of RJ45 keystone socket + SMB including termination charges etc. Preferred Make: Commscope, Actassi, Belden, Molex, R&M, Honeywell or equivalent

OD45991/2024-2025 Supply of 32U network rack with dimension 600x800mm for with cable management, PDU, cooling fan etc

OD45992/2024-2025 Supply and fixing 24 port Enhanced CAT- 6 fully loaded Modular type Patch Panel as per EIA/TIA-TSB 40A specification for interconnecting Switch and Computers, including termination charges. Preferred Make: Actassi, Belden, Molex, R&M, Commscope or equivalent

OD45993/2024-2025 Supply, Installation, Testing and Commissioning of Layer 2 manageable 24 port Ethernet switch with 10/100/1000 ports and 2 Gig SFP, OEM warranty. ( Make:D link,Cisco, Legrand, NetGear)

90.12.12.2 Supply & laying of DWC pipe in ordinary soil 1.2 m below ground level including excavation50/38 mm or nearest size

OD53989/2024-2025 Supply & Installation of 6 CORE SINGLE MODE AMOURED OUTDOOR FIBER CABLE OS2 (2121106-4) Standard, Cable Jacket Material : PE (Polyethylene), UV-resistant, designed for outdoor applications, Compatible with high-bandwidth applications including DWDM, CWDM, and Gigabit Ethernet, Compliant with international standards including ITU-T G.652.D and G.657.A1, OS2 (Optimized for long-distance transmission and supporting data rates up to 10Gbps over 40 km and beyond)

HT Works

OD45994/2024-2025 Supplying and fixing exhaust piping of 100mm dia. Welded black MS, B Class pipe conforming to IS:3589 cut to required lengths and installed with necessary bends supports and clamps anti-vibration mounting, insulation of exhaust system with mineral wool/Rockwool, 50 mm thick wire mesh & aluminum cladding etc., as required as per specifications. up to the top of the building as per pollution control board norms

OD45995/2024-2025 Supply, installation, testing and commissioning of 250 KVA Indoor Unitized Sub Station 250 KVA Resin Cast Indoor Distribution Transformer(Copper wound) Ratio 11KV/433V, 3 Ph., AN cooled, with WTI, Vector Dyn-11 with off circuit tapping from +5% to -10% in steps of 2.5%, changeable by tap links provided, with LV cable box and HV terminals connected to HT Panel 1. 11KV 630A 26.3KA Load Break Switch 2. HT HRC Fuse, Seal off Bushing 3. Al bus Bar, Support Insulators, wiring ,earthing etc. 4. CT : 3 Nos, Ratio :**/5 A, Class 0.2S, 10 VA 5. PT11KV/110V, 25VA, Class:0.2 : 1 No. 6. Provision for TOD Meter. Transformer should be complied with Latest ECBC standards.

OD46331/2024-2025 Supply, installation, testing and commissioning of 100KW/125 KVA, Diesel Generating Set with CPCB IV approved acoustic enclosure comprising of: “Cummins” Model QSB4.5-G2, Radiator Cooled Diesel engine at 1500 RPM, complete with standard accessories. Coupled to “Stamford” Alternator rated at 100KW/125 KVA at 415 Volts mounted on Channel Iron Base Frame complete with Standard Manual control system, Fuel Tank and Batteries

OD45996/2024-2025 Supply, installation, testing and commissioning of 11kV, 3Cx300 sq.mm A2XFY cable in trench / ground<br>etc. as detailed on drawings and complying to specification and standards

OD46000/2024-2025 Supply, Installation, testing and commissioning of emergency isolation push button mounted in standard I.P 65 weather proof break glass enclosure

OD46002/2024-2025 HT CABLE TERMINATION (Heat Shrinkable Joints) Supply, installation, testing and commissioning of cable end terminations for 11kV,3C x 300 sq.mm. XLPE cables with heat shrinkable type end-sealing kit of approved make and quality. Including all required accessories, etc. as required and complying to Specs and standards. OUTDOOR

OD46004/2024-2025 HT CABLE TERMINATION (Heat Shrinkable Joints) Supply, installation, testing and commissioning of cable end terminations for 11kV,3C x 300 sq.mm. XLPE cables with heat shrinkable type end-sealing kit of approved make and quality. Including all required accessories, etc. as required and complying to Specs and standards. INDOOR

OD46006/2024-2025 Fabrication and supply LT panel board, out of 16swg crca sheet, removable gland plate, under gone 7 tank process after powder coating etc as required ,The panel board shall be cubicle indoor type , dust and vermin proof, The bus bars should be of suitable rated TPN Aluminium busbar having the specified normal and short circuit capacities and should be insulated with heat shrinkable color coded PVC sleeves and supported by DMC/SMC type bus bar supports. Frond openable doors, Designing and fabrication of the switch boards should be as per standards of state electrical inspectorate, the assembly must generally confirm to IS/IEC 61439 parts I & II, all interconnection and internal wiring etc."Fabrication of 70kvar Apfc panel Incoming:- 1. 160A TPN ISO - 1Nos. Outgoings:- 1. 32A MCB , 15KVAR cylindrical type capacitor-1nos, 2. 25A MCB , 10KVAR capacitor duty contactor, 10KVAR cylindrical type capacitor-4nos,,3. 16A MCB , 5KVAR capacitor duty contactor, 5KVAR cylindrical type capacitor- 3nos, 4. 8 STEP APFC RELAY with auto manual control

OD46007/2024-2025 Fabrication and supply LT panel board, out of 16swg crca sheet removable gland plate, under gone 7 tank process after powder coating etc as required ,The panel board shall be cubicle indoor type , dust and vermin proof, The bus bars should be of suitable rated TPN Aluminium busbar having the specified normal and short circuit capacities and should be insulated with heat shrinkable color coded PVC sleeves and supported by DMC/SMC type bus bar supports. Frond openable doors, Designing and fabrication of the switch boards should be as per standards of state electrical inspectorate, the assembly must generally confirm to IS/IEC 61439 parts I & II, all interconnection and internal wiring etc."Fabrication of SSB Incoming:- 200A FP ISO- 1Set. Outgoings:- 1. 80A TPN 10KA MCCB - 2Nos. 2. 63A TPN 10KA MCB - 5Nos. Metering:- RYB Indication lamp-1Set,

OD46008/2024-2025 Fabrication and supply LT panel board, out of 16swg crca sheet, removable gland plate, under gone 7 tank process after powder coating etc as required ,The panel board shall be cubicle indoor type , dust and vermin proof, The bus bars should be of suitable rated TPN Aluminium busbar having the specified normal and short circuit capacities and should be insulated with heat shrinkable color coded PVC sleeves and supported by DMC/SMC type bus bar supports. Frond openable doors, Designing and fabrication of the switch boards should be as per standards of state electrical inspectorate, the assembly must generally confirm to IS/IEC 61439 parts I & II, all interconnection and internal wiring etc."Fabrication of DG MAIN PANEL Incoming:- INCOMER- 250A 4P ATS -1Set Outgoings:- 1. 200A TPN 10KA MCCB - 1Nos.2. 125A TPN 10KA MCCB - 1Nos. 3. 63A TPN 10KA MCCB - 1Nos.4.63A FP ISO-1No.Metering:- RYB Indication lamp-1Set

OD46009/2024-2025 Fabrication and supply LT panel board, out of 16swg CRCA sheet, removable gland plate, under gone 7 tank process after powder coating etc as required ,The panel board shall be cubicle indoor type , dust and vermin proof, The bus bars should be of suitable rated TPN Aluminium busbar having the specified normal and short circuit capacities and should be insulated with heat shrinkable color coded PVC sleeves and supported by DMC/SMC type bus bar supports. Frond openable doors, Designing and fabrication of the switch boards should be as per standards of state electrical inspectorate, the assembly must generally confirm to IS/IEC 61439 parts I & II, all interconnection and internal wiring etc."Fabrication of Main Switch Board EB Incoming:- EB- 630A 36KA 4P EF MP Release MCCB- 1Set. Outgoings:- 1. 320A TPN 25Ka TM Release MCCB - 1Nos. 2. 250A TPN 25Ka TM Release MCCB - 2Nos. 3. 160A TPN 25Ka TM Release MCCB - 2Nos. Metering:- RYB Indication lamp-2Set DCM (VAF)-2No. EFR-1Set

OD46010/2024-2025 Fabrication and supply LT panel board, out of 16swg CRCA sheet, removable gland plate, under gone 7 tank process after powder coating etc as required ,The panel board shall be cubicle indoor type , dust and vermin proof, The bus bars should be of suitable rated TPN Aluminium busbar having the specified normal and short circuit capacities and should be insulated with heat shrinkable color coded PVC sleeves and supported by DMC/SMC type bus bar supports. Frond openable doors, Designing and fabrication of the switch boards should be as per standards of state electrical inspectorate, the assembly must generally confirm to IS/IEC 61439 parts I & II, all interconnection and internal wiring etc "Fabrication of HVAC PANEL Incoming:- 315A FP 25Ka MCCB- 1No. Outgoings:- 1. 63A TPN 10KA MCCB - 8Nos. 2. 80A TPN 10KA MCCB - 5Nos. Metering:- RYB Indication lamp-1Set

OD46332/2024-2025 Lift Panel - Fabrication,supply,erection,testing and commissioning of cubicle type,dust and vermin proof ,floor /wall mounted,front operated MV Panel board made out of 16 SWG thick CRCA sheet fully compartmentalized complete with hinged and earthed front doors with name plate ,danger notice board,heavy duty rubber gaskets,removable gland plates made out of 3mm thick sheet steel including all components as shown in the schematic drawing.All opening parts of the panel shall be sealable. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant. <br>Incomer- 1) 63A,433V,50Hz,4P MCB- 1No, 63A,433V,16kA best conductivity bus bar with SMC supports,heat shrinkable sleeves etc complete as required. RYB phase indicating lamps with control fuses and switches - 1No. Outgoing 40A 100 mA FP ELMCB-1No, 25A ,30 mA MCB+ ELCB- 1No

OD46011/2024-2025 Collection of Data, Preparation of Drawings and other necessary documents, submitting to the District Electrical Inspector, Attending Technical Meeting and finally obtain the Scheme Approval, energization certificate . Also Preparation of Completion Report and other necessary documents, submitting to the KSEB Electrical Section, arranging Inspection, attending Technical Meeting and finally obtain power allocation and Availing EB connection. Remittance of Statutory Fee is excluded from the scope of Electrical Vendor and it shall be Remitted by the Consumer Other Engineering Organizations

OD46014/2024-2025 Supply,installaton,testing and commissioning of 11kKV 630A, 21kA SF6 Insulated Outdoor Motorized Extensible 1 Way Consisting Of 12 VCB RMU Type SABRA - VCE for coupling with existing RMU

OD46016/2024-2025 Supply and fixing position the approved single line diagram framed in A0 size 5mm acrylic sheet frame and installed in Panel Room

OD46018/2024-2025 Supply and fixing danger notice board of 250mm x 200mm made of mild steel, at least 2mm thick and vitreous enameled white on both sides and with inscription in signal Red Colour on front side s per IS & KSEB norms."- 11 KV

OD46019/2024-2025 Supply and fixing danger notice board of 250mm x 200mm made of mild steel, at least 2mm thick and vitreous enameled white on both sides and with inscription in signal Red Colour on front side s per IS & KSEB norms."- 433 Volt

OD46020/2024-2025 Supply of 11KV Rubber Hand Safety Gloves

OD46021/2024-2025 Supply and providing First Aid Chart duly framed and placed in a conspicuous location for clear vision

OD46022/2024-2025 Supply and providing 9 Litre capacity, round bottom GI Fire Bucket, painted in post office red with primer coat of red oxide and written with white paint 'FIRE mounted on MS angle frame work / wall bracket filled with fine sand, painting the bracket, floor stand etc. including making good the damages, colour washing etc. as required.

OD46024/2024-2025 Supply and providing one meter wide 2.5 mm thick electrical grade anti skid class A insulation floor mat 11KV grade, 45KV BDV made from highly electrical resistance elastomers conforming to IS 15652/ 2006.

OD46025/2024-2025 Supply and fixing of 4Kg ABC Dry Powder (Stored Pressure) Type Fire Extinguisher. pressurized with dry nitrogen gas at 15 bar. Design, construction and testing as per IS 15683 with Fire rating 1A 8B, Body Hydrotested at 35 bar, Operating temperature ‐30°C to<br>+55°C, external epoxy powder coating with PO Red Shade No. 538 of IS 5, Supplied with standard accessories.

Passenger Lift

OD45004/2024-2025 15 Passenger Lift-Design, fabrication, supply. installation, testing and commissioning of 15 Passenger Lift – Gear less with Machine Room, Capacity / Weight 15 Pass (1020 Kg), Speed 1 MPS, electric traction type, Stainless steel (Including freight & landing charges, insurance and all applicable taxes and duties in country of origin and in India etc. except GST) and type suitable for operation on 415 V±10%, 3 phase, 50 Hz AC supply, having AC variable voltage and variable frequency micro-processor type traction control, electromagnetic brake system, Simplex mode operation, operating panel with luminous buttons, voice announcement and brainlee, Lift ventilation with auto power on and off function ,overload warning indicator, battery operated alarm bell, LED type emergency light, intercom suitable for hook up to Purchaser’s EPABX in the ground floor, infrared ray sensing door protection for full height, reverse phase relay on controller, fireman's switch at initial landing floor, LCD/LED car positions and direction indication in car and landings. And at all floors with UP/DOWN direction, shaft wiring and lighting with accessories, braille buttons, audio announcement along with pre-recorded message as approved by Engineer-in-Charge, all accessories including Safe Landing Device (SLD), Automatic Rescue Device (ARD) with minimum 3 operations in 5 minutes , dry maintenance free sealed batteries and Manual Emergency Rescue Device and all electrical components with wiring from the single point power supply provided at top landing near the elevator door complete as required. The drives of elevator shall meet the requirements of IEEE 519/2014. PMSM traction motor ( having efficiency equivalent to IE3 or better as in IS 12615) of machine room elevator shall be of gearless type and placed inside the machine room complete as per technical specifications. Having automatic center /side opening stainless steel doors, 20 mm recess stainless steel car enclosure provided with stainless steel handrails on three sides, 2 mm fluted SS flooring as applicable in accordance of following details- 04 stops, 04 openings and entrance and exit at same side and suitable for travel height of 14.40 meter approximate. (Shaft Size 2200mm (width) x 2400mm (depth)) with door opening of 1000 mm (width) and 2000 mm (height), Car dimensions 1600 mm wide x 1600 mm deep x 2200 mm height, Door type -Two-panel center opening with vision panel at half length with fire rated glass . The equipment should be BMS compatible. The elevator should have suitable True WDR 120dB night vision camera fixed inside the cart with the output given to the nearest network port. All components, fabrication and procedures shall confirm to relevant IS standards/Code and complete in all respects as per technical specifications. Test reports from NABL accredited testing labs for all constituent compounds shall be produced, (Make: Kone /Schneider/Mitsubishi/ equivalent..). Efficiency level of lift shall be equal to or better than C as per IS 17517

Air Conditioning work

OD46161/2024-2025 SUPPLY,INSTALLATION,TESTING AND COMMISSIONING OF HARD DRAWN COPPER REFRIGERANT PIPING INCLUDING ALL ACCESSORIES INCLUDING JOINTS PROPERLY BRAZED INSULATED WITH CHEMICALLY CROSSLINKED NITRILE RUBBER FIRE RETARDANT GRADE CLASS O WITH19MM THICKNESS AND NECESSARY SUPPORTS AS REQUIRED OF SIZE 41.3MM

OD46162/2024-2025 Supply of Wireless remote

OD46163/2024-2025 Supply, installation, testing and commissioning of 2 tr (3 mtr Copper pipe kit included) 5 star inverter split ac with ISEER 5 rating, 100%Copper condenser coil, R32 refrigerant gas and single-phase Rated power supply having 1 year warranty on machine , 5 Years on compressor and 5 years warranty on PCB . Make: Blue Star /Daikin/Carrier or equivalent.

OD65334/2024-2025 Supply, installation, testing and commissioning of wall mounting type 5 kVA voltage stabilizer, Conforming to IS:8448 latest standards with input voltage single Phase Sine wave (120V-280v) and Output Single Phase sine wave (210V-250V) Overall efficiency of ALVC (%) > / = 95% having Copper Windings, features of high power efficiency, intelligent time delay system, Low & High voltage cut-off protection, built-in thermal overload protection, LED indications etc suitable for single phase 2-Ton air conditioner unit with three years warranty and three months replacement guarantee. (Make: V-Guard VDI, Microtek – Smart, Crompton)

OD46164/2024-2025 SUPPLY, INSTALLATION, TESTING AND COMMISSIONING OF Y JOINTS IN DOOR SIDE

OD46165/2024-2025 SUPPLY, INSTALLATION, TESTING & COMMISSIONING OF MODULAR TYPE VRF ODU.THE OUTDOOR UNIT SHALL BE FACTORY ASSEMBLED, WEATHER PROOF CASING, CONSTRUCTED FROM HEAVY GAUGE MILD STEEL PANELS AND COATED WITH BAKED ENAMEL FINISH. THE UNIT SHOULD BE COMPLETELY FACTORY WIRED TESTED WITH ALL NECESSARY CONTROLS. OUTDOORS UNITS OF THE VRF/VRV SYSTEM SHALL BE COMPACT AIR COOLED TYPE.ALL THE COMPRESSORS OF THE OUTDOOR UNITS MUST BE HERMETICALLY SEALED BLDC INVERTER SCROLL/TWIN ROTARY TYPE. OEM SHOULD USE THERE ON MAKE COMPRESSORS IN VRF /VRV SYSTEM WHICH IS TO BE SUPPLIED. SYSTEM COP SHALL NOT BE LESS THAN – 3.7 AT AHRI CONDITION AND SUITABLE TO OPERATE AT HEAT LOAD PROPORTIONAL TO INDOOR TEMPERATURE REQUIREMENT. ALUMINUM FINS OF CONDENSER COIL SHALL HAVE ANTI CORROSIVE BLACK / BLUE/ YELLOW EPOXY RESIN OCEAN BLACK COATING ALONG WITH HYDROPHILIC COATING. PRE-COATED AT FACTORY. THE ANTI-CORROSIVE TREATMENT SHOULD HAVE BEEN TESTED FOR AT LEAST 2500HRS OF STANDARD SALT SPRAY TEST AND MUST HAVE A CERTIFIED LIFE OF MINIMUM 20 YEARS SUPPORTED BY CERTIFICATE FROM REPUTED INTERNATIONAL INSTITUTION IS MANDATORY. THE TREATMENT SHOULD BE SUITABLE FOR AREAS OF HIGH POLLUTION AND SALT LADEN AIR.MODULAR SUYTEM TO BE CONFIGURED AS PER MENTION MODULES GIVEN IN BRACKET- 22HP

OD46166/2024-2025 SUPPLY, INSTALLATION, TESTING & COMMISSIONING OF MODULAR TYPE VRF ODU.THE OUTDOOR UNIT SHALL BE FACTORY ASSEMBLED, WEATHER PROOF CASING, CONSTRUCTED FROM HEAVY GAUGE MILD STEEL PANELS AND COATED WITH BAKED ENAMEL FINISH. THE UNIT SHOULD BE COMPLETELY FACTORY WIRED TESTED WITH ALL NECESSARY CONTROLS. OUTDOORS UNITS OF THE VRF/VRV SYSTEM SHALL BE COMPACT AIR COOLED TYPE.ALL THE COMPRESSORS OF THE OUTDOOR UNITS MUST BE HERMETICALLY SEALED BLDC INVERTER SCROLL/TWIN ROTARY TYPE. OEM SHOULD USE THERE ON MAKE COMPRESSORS IN VRF /VRV SYSTEM WHICH IS TO BE SUPPLIED. SYSTEM COP SHALL NOT BE LESS THAN – 3.7 AT AHRI CONDITION AND SUITABLE TO OPERATE AT HEAT LOAD PROPORTIONAL TO INDOOR TEMPERATURE REQUIREMENT. ALUMINUM FINS OF CONDENSER COIL SHALL HAVE ANTI CORROSIVE BLACK/ BLUE/ YELLOW EPOXY RESIN OCEAN BLACK COATING ALONG WITH HYDROPHILIC COATING. PRE-COATED AT FACTORY. THE ANTI-CORROSIVE TREATMENT SHOULD HAVE BEEN TESTED FOR AT LEAST 2500HRS OF STANDARD SALT SPRAY TEST AND MUST HAVE A CERTIFIED LIFE OF MINIMUM 20 YEARS SUPPORTED BY CERTIFICATE FROM REPUTED INTERNATIONAL INSTITUTION IS MANDATORY. THE TREATMENT SHOULD BE SUITABLE FOR AREAS OF HIGH POLLUTION AND SALT LADEN AIR.MODULAR SUYTEM TO BE CONFIGURED AS PER MENTION MODULES GIVEN IN BRACKET- 16 HP

OD46167/2024-2025 Supply, Installation, Testing and Commissioning of hard drawn copper refrigerant piping including all accessories, including joints properly brazed insulated with chemically cross-linked nitrile rubber fire retardant grade class o with suitable thickness to attain the R value specified in ECBC 2017, with glass tape / all-weather tape and necessary supports as required of size 9.52mm dia

OD46168/2024-2025 Supply, Installation, Testing and Commissioning of hard drawn copper refrigerant piping including all accessories including joints properly brazed insulated with chemically cross-linked nitrile rubber fire retardant grade class o with suitable thickness to attain the R value specified in ECBC 2017 , with glass tape / all-weather tape and necessary supports as required of size 12.7mm dia

OD46169/2024-2025 Supply, Installation, Testing and Commissioning of hard drawn copper refrigerant piping including all accessories including joints properly brazed insulated with chemically cross-linked nitrile rubber fire retardant grade class o with suitable thickness to attain the R value specified in ECBC 2017 , with glass tape / all-weather tape and necessary supports as required of size 15.9mm dia

OD46171/2024-2025 Supply, Installation, Testing and Commissioning of hard drawn copper refrigerant piping including all accessories including joints properly brazed insulated with chemically cross-linked nitrile rubber fire retardant grade class o with suitable thickness to attain the R value specified in ECBC 2017 , with glass tape / all-weather tape and necessary supports as required of size 19.05mm

OD46172/2024-2025 Supply, Installation, Testing and Commissioning of hard drawn copper refrigerant piping including all accessories including joints properly brazed insulated with chemically cross-linked nitrile rubber fire retardant grade class o with suitable thickness to attain the R value specified in ECBC 2017, with glass tape / all-weather tape and necessary supports as required of size 22.2mm dia.

OD46174/2024-2025 Supply, Installation, Testing and Commissioning of hard drawn copper refrigerant piping including all accessories including joints properly brazed insulated with chemically cross-linked nitrile rubber fire retardant grade class o with suitable thickness to attain the R value specified in ECBC 2017, with glass tape / all-weather tape and necessary supports as required of size 28.6mm dia.

OD46175/2024-2025 SUPPLY, INSTALLATION, TESTING AND COMMISSIONING OF CASSETTE TYPE VRF INDOOR UNITS. THE INDOOR UNIT SHALL BE OF THE FOURWAY CASSETTE TYPE INDOOR UNITS AS PER THE REQUIREMENTSSPECIFIED IN THE BOQ / DRAWINGS. ALL INDOORS HAVE ELECTRONIC EXPANSION VALVE THAT CONTROLS THE FLOW OF REFRIGERANT IN RESPOND TO THE LOAD VARIATIONS OF ROOM ACCORDING TO SET TEMPERATURE, WHICH CAN SET BY REMOTE CONTROLLERS. ALL INDOOR UNITS SHOULD HAVE INBUILT DRAIN PUMP WITH MINIMUM 700MM VERTICAL LIFT HEAD. ELECTRICITY CHARACTERISTICS FOR INDOOR UNIT SHALL BE 240 VOLTS/ 1PHASE / 50HZ- 4-WAY CASSETTE TYPE - 4TR

OD46176/2024-2025 SUPPLY, INSTALLATION, TESTING AND COMMISSIONING OF CASSETTE TYPE VRF INDOOR UNITS. THE INDOOR UNIT SHALL BE OF THE FOURWAY CASSETTE TYPE INDOOR UNITS AS PER THE REQUIREMENTS SPECIFIED IN THE BOQ / DRAWINGS. ALL INDOORS HAVE ELECTRONIC EXPANSION VALVE THAT CONTROLS THE FLOW OF REFRIGERANT IN RESPOND TO THE LOAD VARIATIONS OF ROOM ACCORDING TO SET TEMPERATURE, WHICH CAN SET BY REMOTE CONTROLLERS. ALL INDOOR UNITS SHOULD HAVE INBUILT DRAIN PUMP WITH MINIMUM 700MM VERTICAL LIFT HEAD. ELECTRICITY CHARACTERISTICS FOR INDOOR UNIT SHALL BE 240 VOLTS/ 1PHASE / 50HZ- 4-WAY CASSETTE TYPE - 3 TR

OD46177/2024-2025 SUPPLY,INSTALLATION,TESTING AND COMMISSIONING OF 5/8" SOFT DRAWN COPPER REFRIGERANT PIPING INCLUDING ALL ACCESSORIES FOR SPLIT AC

OD46178/2024-2025 SUPPLY,INSTALLATION,TESTING AND COMMISSIONING OF 3/8" SOFT DRAWN COPPER REFRIGERANT PIPING INCLUDING ALL ACCESSORIES FOR SPLIT AC

OD46179/2024-2025 SUPPLY, INSTALLATION, TESTING AND COMMISSIONING OF Y JOINTS- Y JOINT- OUTDOOR SIDE

OD46180/2024-2025 SUPPLY, INSTALLATION, TESTING & COMMISSIONING OF OUDOOR UNIT POWER SUPPLY CABLING USING 10 SQMM 4 CORE CABLE

90.6.5.4 Supply and drawing the following sizes of multi-core PVC insulated & FRLS PVC sheathed 650/1100 V grade copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface / recess conduit as required including giving necessary connections of the following sizes.2 core 1.50 sq mm

OD46182/2024-2025 Supply, installation, testing & commissioning of additional refrigerant gas charge R32 A , for extra pipe length (split unit)

OD46184/2024-2025 SUPPLY, INSTALLATION, TESTING & COMMISSIONING OF PEDESTIAL/ODU STAND FOR PLACING VRF ODU

OD46185/2024-2025 Supply, Installation, Testing & Commissioning of additional refrigerant gas charge R410 A , for extra pipe length (VRF Unit)

OD46186/2024-2025 SUPPLY, TESTING AND COMMISSIONING OF CONDENSATE CONDENSATE DRAIN UPVC PIPING AS PER BIS 4985 WITH NECESSARY CLAMPS, SUPPORTS, HANGERS AND FITTING SUCH AS BEND, TEES, REDUCERS ETC COMPLETE AS PER SPECIFICATIONS AND AS REQUIRED., ALL COMPLETE AS PER DIRECTION OF ENGINEER-IN-CHARGE 32MM DIA UPVC

90.6.5.11 Supply and drawing the following sizes of multi-core PVC insulated & FRLS PVC sheathed 650/1100 V grade copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface / recess conduit as required including giving necessary connections of the following sizes.3 core 1.50 sq mm

90.9.1.1 Supply and fixing 50 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.50x50mm Cable Management System with base and lid

90.9.2.1 Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.100 x 50 mm CMS with base and lid

OD50901/2024-2025 Supply and installation of AC Stand for Out door unit wall mounting, upto 2 ton , made with Heavy Duty GI Steel . Fixing using appropriate anchor bolt with vibration isolator .

Fire Fighting Work

OD46188/2024-2025 PRESSURE GAUGE- Supply, installation, testing and commissioning of pressure gauge with 0 to 12kg range 4" dia.(Make: H Guru)

OD46189/2024-2025 PRESSURE SWITCH- Supply, installation, testing and commissioning of pressure Switch.(Make: Danfoss/Indifss/Accuree)

OD46190/2024-2025 DOL PANEL- Supply, installation, testing and commissioning of motor control panel for the Terrace pump for fire fighting including all necessary control wiring with indication lamps and meters

OD46191/2024-2025 TERRACE PUMP- Supply, erection, testing and commissioning of Electrical driven Terrace pump with all necessary valves and fittings comprising as follows: Electrical motor driven pump capable of delivering 450 LPM at a head of 18Mtrs electrical motor fitted in a common base plate, coupling and coupling guard complete. (make . Kirloskar/ LUB)

OD46195/2024-2025 Piping- Supply, erection, testing and commissioning of above ground piping of approved make medium quality MS"B" class pipes with branded malleable specials conforming to IS 1239 part 1 & 2 such as tees, elbows, unions, flanges, nipples etc. including cutting, welding and painting the exposed pipes with one coat of zinc chromate primer and two coats of PO red enamel paint. The pipes shall be supported suitably- 80mm dia (Make: Tata/Jindal)

OD46198/2024-2025 Piping- Supply, erection, testing and commissioning of above ground piping of approved make medium quality MS"B" class pipes with branded malleable specials conforming to IS 1239 part 1 & 2 such as tees, elbows, unions, flanges, nipples etc. including cutting, welding and painting the exposed pipes with one coat of zinchromate primer and two coats of PO red enamel paint. The pipes shall be supported suitably..- 100mm dia (Make: Tata/Jindal)

OD46200/2024-2025 AIR RELEASE VALVE- Supply, installation, testing and commissioning of gunmetal air release valve 25 mm with necessary fittings etc. complete.(Make: Arihant/Karthar/Atom)

OD46201/2024-2025 BALL VALVE- Supply, installation, testing and commissioning of Ball valve of following dia- 20 mm (Make: Zoloto/Karthar)

OD46202/2024-2025 FIRE BRIGADE INLET - Supply, installation, testing and commissioning of 2 way Fire Brigade Inlet connection of 63 mm dia. built - in Gun metal Non- return valves instantaneous coupling type arrangement to be connected to wet riser main.(Make: Arihant/Newage/Karthar)

90.17.18.2 Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :Stainless Steel (Grade 304

90.17.16.2 Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :Stainless Steel (Grade 304)

OD46206/2024-2025 HOSE BOX- "Supply, installation, testing and commissioning of hose boxes wall/pedestal type of size 600 x 250 x 400 mm made out of 18 guge MS sheet steel with front side glass, locking arrangement and painted with approved colour completed as required and as per specifications.(Make:Friends)

90.17.17.1 Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. a.20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 b.20 mm nominal internal dia gun metal globe valve & nozzle. c.Drum and brackets for fixing the equipmets on wall. d.Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 m

OD46208/2024-2025 HYDRANT VALVE- Supply, erection, testing and commissioning of single headed Hydrant valve stainless steel with ISI mark as per the IS specification fitted to 80mm dia pipe .(Make: Arihant/Newage/Karthar)

90.17.14.5 Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :100mm dia

90.17.11.5 Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required100 mm dia

OD46212/2024-2025 SIGN BOARDS -Supply & erection of Glow Sign Board made of 3mm thick PVC foam board for each floor 12" x 4" - EXIT

OD46213/2024-2025 SIGN BOARDS -Supply & erection of Glow Sign Board made of 3mm thick PVC foam board for each floor 12" x 4" - FIRE EXIT

OD46214/2024-2025 SIGN BOARDS -Supply & erection of Glow Sign Board made of 3mm thick PVC foam board for each floor 12" x 4" - FIRE DUCT

OD46215/2024-2025 FIRE EXTINGUISHER:- Supply and Installation of Co2 4.5 Kg Fire Extinguisher complete with initial charges and installation brackets

OD46216/2024-2025 MODULAR FIRE EXTINGUISHER : Supply, Installation, Testing and Commissioning of Modular ( Clean Agent ) fire extinguisher 5Kg capacity

OD46217/2024-2025 ABC FIRE EXTINGUISHER -Supply and installation of ABC Stored pressure type Fire Extinguisher 4 Kgs Capacity Mono Ammonium Phosphate based Dry Chemical Powder as per IS 14609 with ISI Mark for Fighting ABC Class of Fire, stored Pressure type of Mild steel body pressurized by Nitrogen Gas. The Extinguisher shall have pressure gaugefor indicating inside pressure with opening and closing lever of squeeze grip type with tamper proof seal, complete with wall bracket. The Extinguisher should be manufactured strictly as per IS: 15683:2006 with ISI mark.(Make: Safex/Safepro/Kanex)

1.17.1 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.1 x 1.5 sq. mm

1.21.1 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

OD46220/2024-2025 HOOTER- Supply, installation, testing and commissioning of Electronic dual tone Hooter (Sounder) as per standard specification.(Make: Agni/Ravel)

17.1.3 FIRE DETECTION AND ALARM SYSTEM (CONVENTIONAL)Supplying, installation, testing & commissioning of manual call boxes of MS Construction in surface/recess with stainless steel chain & hammer assembly Complete with glass and push button etc. as required.

OD46226/2024-2025 Fire Alarm System- Supply, installing, testing and commissioning of Micro processor based Main Fire alarm control panel of 8 zones capacity, with visual LED indications for fire / fault alarms, signals and should have stage alarm facility with maintenance free battery back up for 24 hours normal operation and 15 minutes alarm operation. The panel shall be fabricated by M.S. sheet and powder coated both inside & out side, door shall be glass fronted type with locking arrangement, as per specification.(Make: Agni/Ravel)

OD50946/2024-2025 Supply installation testing and commissioning of 1.7 KV/24 V ( CP+1750/24 V ) Pure sinewave Home Ups inverter with 2 Numbers Hykon 12V/100 Ah 2 numbers Tubular batteries with stand.

M/s Crescent Construction Company (BID ID -2187254)

Bidder Name

Peter Kuriakose

M/s Crescent Construction Company