CONSTRUCTION OF LIBRARY BUILDING, FARIYADKA AT BHAVNAGAR FOR BHAVNAGAR AREA DEVELOPMENT AUTHORITY (BADA). DISTRICT: BHAVNAGAR.

SCHEDULE -B ABSTRACT SHEET

Schedule No. Description of Work Amount Put to Tender

Schedule- B1 Civil Work

Schedule- B2 Plumbing

Schedule- B3 Electrical

Schedule- B4 Interior Work

TOTAL TENDER COST IN (Rs.)

Estimated Amount

Rs………………………. Sub total amount put to the

Rs………………………. Sub total amount put to the

Sub total amount put to the tender

Sub total amount put to the tender

Deduct…………. % below Rs………………………. Add…………. % above

Net Rs………………………. Net

Note-1 All work shall be carried out as per public works department hand book

and other specifications as per tender or as directed by Engineer in

Note-2 Rates quoted include clearance of site (Prior commencement of work and

at its close) in all respects and hold good for work under all conditions,

site, moisture, weather etc.

Executive Engineer

Signature of Contractor with Stamp Bhavnagar Area

Development Authority

Bid Documents for Construction of Library Building, Fariyadka at Bhavnagar

Sr. No. Description Total Qty Unit Rate Amount

Excavation for foundation up to 1.5 mt. depth including sorting out and stacking of useful materials and

disposing of the excavated stuff up to All lead & Lift. (A) Loose or soft soil

Excavation for foundation 1.5 to 3.0 mt. depth including sorting out and stacking of useful materials and

disposing of the excavated stuff up to 50 meter lead. (A) Loose or soft soil

Filling available excavated earth (excluding rock) in trenches. plinth, sides of foundations etc. in layers

3 not exceeding 20 cm. in depth consolidating each disposited layer by ramming and watering. 253.32 CUM 137.47

Providing and laying cement concrete 1: 4: 8 (1 cement: 4 coarse sand: 8 machine crushed Black

4 Trape stone aggregates 40 mm nominal size) and curing complete excluding cost of formwork in: (A) 23.07 CUM 2754.51

Foundation and plinth

Providing & laying in position controlled reinforced cement concrete (RMC) of following grades with

concrete batch mix plant, machined batched & machine vibrated design mix cement concrete using

graded hard (black trap) stone agg. of 20mm Nominal size obtained from approved quarry incl. fine

aggregate confirming to latest IS 383, admixtures and cement all as per approved design mix as per IS

10262 with minimum cement content as specified along with relevant grade of concrete in IS-456 and/

or according to Design mix to be followed, including mixing, transporting, pumping, placing, vibrating,

compaction, finishing to required levels, curing, dewatering, roughening and / or hacking concrete etc

complete all as per specifications at all elements, all locations, all heights, all leads, all depths from FFL /

GL., in any position & any shape for all structures as per specifications & / or as directed by Engineer in

5 The Rate shall be inclusive of labour for keeping embedments if any, wherever required while casting, 13.61 CUM 4788.41

including the cost of centering, shuttering, formwork, staging, scaffolding (rates for centering, shuttering,

formwork, staging, scaffolding for considering rates should be for clear floor height of 4.5mtrs. Extra

staging above clear floor height of 4.5mtrs will be paid extra in relevant tender item) concrete cover

blocks, admixtures, materials, labour etc complete but excluding the cost of reinforcement steel. All

material shall confirm to relevant IS standards. For all Civil, Plumbing, Electrical & infrastructure Works.

Note: Design Mix should carried out only as per the cement content specified in IS-456. No deviation in

cement content will be allowed.

A) M25-For Foundation

Providing & laying in position controlled reinforced cement concrete of following grades with concrete

batch mix plant , machined batched & machine vibrated design mix cement concrete using graded

hard (black trap) stone agg. of 20mm Nominal size obtained from approved quarry incl. fine

aggregate confirming to latest IS 383, admixtures and cement all as per approved design mix as per IS

10262 with minimum cement content as specified along with relevant grade of concrete in IS-456 and/

or according to Design mix to be followed, including mixing, transporting, pumping, placing, vibrating,

compaction, finishing to required levels, curing, dewatering, roughening and / or hacking concrete etc

complete all as per specifications at all elements, all locations, all heights, all leads, all depths from FFL /

GL., in any position & any shape for all structures as per specifications & / or as directed by Engineer in

6 Charge. 164.16 CUM 8648.63

The Rate shall be inclusive of labour for keeping embedments if any, wherever required while casting,

including the cost of centering, shuttering, formwork, staging, scaffolding (rates for centering, shuttering,

formwork, staging, scaffolding for considering rates should be for clear floor height of 4.5mtrs. Extra

staging above clear floor height of 4.5mtrs will be paid extra in relevant tender item) concrete cover

blocks, admixtures, materials, labour etc complete but excluding the cost of reinforcement steel. All

material shall confirm to relevant IS standards. For all Civil, Plumbing, Electrical & infrastructure Works. -

A) M20 - For Column & Beam

Providing & laying in position controlled reinforced cement concrete (RMC) of following grades with

concrete batch mix plant , machined batched & machine vibrated design mix cement concrete using

graded hard (black trap) stone agg. of 20mm Nominal size obtained from approved quarry incl. fine

aggregate confirming to latest IS 383, admixtures and cement all as per approved design mix as per IS

10262 with minimum cement content as specified along with relevant grade of concrete in IS-456 and/

or according to Design mix to be followed, including mixing, transporting, pumping, placing, vibrating,

compaction, finishing to required levels, curing, dewatering, roughening and / or hacking concrete etc

complete all as per specifications at all elements, all locations, all heights, all leads, all depths from FFL /

GL., in any position & any shape for all structures as per specifications & / or as directed by Engineer in

7 The Rate shall be inclusive of labour for keeping embedments if any, wherever required while casting, 130.00 CUM 7622.47

including the cost of centering, shuttering, formwork, staging, scaffolding (rates for centering, shuttering,

formwork, staging, scaffolding for considering rates should be for clear floor height of 4.5mtrs. Extra

staging above clear floor height of 4.5mtrs will be paid extra in relevant tender item) concrete cover

blocks, admixtures, materials, labour etc complete but excluding the cost of reinforcement steel. All

material shall confirm to relevant IS standards. For all Civil, Plumbing, Electrical & infrastructure Works.

Note: Design Mix should carried out only as per the cement content specified in IS-456. No deviation in

cement content will be allowed.

A) M20-For Slab

Providing T.M.T Fe 500 D bar reinforcement for R.C.C. work including bending, binding and placing in

position complete up to floor two level.

Brick work using common burnt clay building bricks having crushing strength not less than 35kg/Sqcm. in

9 foundation and plinth. In cement mortar 1:5 (1 cement : 5 fine sand) (B) Conventional 173.96 CUM 4310.73

Half brick masonry in common brunt clay building bricks having crushing strength not less than

Kg/Sq.Cm. in Cement mortar 1:3 ( 1-Cement : 3- coarse sand ) with 2 Nos of 6mm Mild steel round bars

after every three course embedded in Cement Mortar in foundation and plinth (B) Conventional

Providing 15 mm. thick single coat cement finish plaster on fair side of brick/block wall/ RCC for interior

plastering upto floor two level finished even and smooth in [I] Cement mortar 1:3 (1 cement : 3 fine

sand) including with necessary scaffolding, finishing, curing, making grooves, forming pattas, hacking

11 properly RCC surface, hexagonal chickenmesh of size 20 mm. x 20 mm. of 22 gauge at junction of 901.80 Sqm 200.08

concrete and brick work or between different materials, etc. as directed. (for all civil, plumbing &

electrical works) by the Architect and Engineer-in-charge. for

Providing 10mm thick cement plaster in single coat on brick/concrete walls for interior plastering upto

12 floor two level and finished even and smooth in (i)Cement mortar 1:3 (1-cement:3-sand) 660.00 Sqm 149.12

Providing and laying average 18-20 mm. thick Sand faced cement plaster on masonry work / RCC wall

upto any height above ground level and for all shapes consisting of first coat (backing coat) average

12-15 mm. thick with CM 1:3 (1 cement: 3 coarse sand) rough wired finish and second coat of average

6 mm. thick uniform grained textured by using wooden Gutka, in CM 1:3 (1 cement: 3 sand), including

13 with necessary scaffolding, finishing, curing, making grooves, forming pattas, hacking properly RCC 486.60 SQM 350.57

surface, hexagonal chickenmesh of size 20 mm. x 20 mm. of 22 gauge at junction of concrete and

brick work or between different materials, etc. as directed. (for all civil, plumbing & electrical works) by

the Architect and Engineer-in-charge.

Providing & fixing in position Domal Fully paneled or Partly glazed & partly paneled coloured anodized

60 micron aluminium single/Double leaf door standard section (Jindal or Equivalent) for frame Door

top sec no 3653 85 mmx44.5x2 mm( wt 5.00-5.50 kg/12'),door vertical sec no 3753 85 mm

x44.5mmx1.90 mm ( wt 5.00-5.50 kg/12') door middle double sec no 3852 -85 mmx44.5x1.85 mm( wt 5.00-

5.50 kg/12') rectangular tube sec no -5351 100 mm x12.70 x1.48 mm( wt 5.00-5.50 kg/12') door middle

single sec no 3951 -85 mm x44.5 mmx1.40 mm( wt 3.00-3.40 kg/12') glazing clips size 19 mm x17 mm Wt

@ 0.12 kg/m with 5 mm thick laminated compact sheet , 5 mm thik glass (Modi float or saint gobain

brand at Top& bottom panel fix by glazing clips including providing & fixing S.S. handle & stopper,

aldrop & mortise lock, SS screw with fixture & fastening including cutting the flooring, making good etc.

all required materials labours and equipments with fixing as per detailed drawing or as direct EIC.

Providing and fixing 35 mm thick single shutter flush door including Indian teakwood frames 12cm x 7cm

, water proof flush door single shutter with 1.0 mm thick decorative lamination on both side, Indian teak

wood beddig patti of the size 20 mm 35 mm to all sides of shutter & three coat of oil painting to sides of

shutters using two Nos of 'I' shape pull handles in satin finish of the size 25mm diameter, 300mm long

made from anticorrosive high grade AISI 316 stainless steel Satin finish as approved by Engineer - in

charge including providing & one number of 10 mm diameter 10" long anticorrosive high grade AISI

stainless steel tower bolt in satin finish, three numbers of anticorrosive high grade AISI 316 stainless steel

hinges of size 102 mm x 76 mm x 3 mm & anticorrosive high grade AISI 316 stainless steel, 10 mm

diametre x 250 mm long aldrap in satin finish including strenthning the granite jembs & Soffit by means

of anchor bolts by drilling hole in the granite prior to fixing door as per instruction & approval by

Engineer -in-charge etc. complete as per detailed drawing

Providing and fixing window having extruded aluminum Colour anodized section frame main outer size

127mm x 38.10mm x 1.35mm @wt. 1.384kg/m, horizontal Four track member size 122.20mm x 31.75mm x

1.10mm@ wt 1.205 kg/m, vertical member of size 122.20mm x 31.75mm x 1.50mm @1.398 kg/mt with

sliding shutters of horizontal member size 40mm x 18mm x 1.29mm@ 0.456kg/mt ,vertical member of size

40mm x 18mm x 1.29mm @ 0.456 kg/mt with 5 mm thick transparent bronze colour tinted float glass with

powder coated aluminum fittings and fixtures and transparent silicon sealant glass fixing to frame as per

details etc complete for window.

Providing and fixing standared extruded of alluminium section of size 63mm x 38.10mm x 1.2mm @ Wt.

17 0.643 Kg/mt with colour anodized alluminium frame for ventilation with 5 mm thick frosted glass as 6.00 Sqm 1280.31

details etc complete for Ventilation

Providing, fabricating, assembling, hoisting, erecting, fixing in position of welded/ bolted structural steel

work at all heights/ all levels/ all floors/ all shapes & sizes with all leads & lifts using MS Rolled Steel

Sections, Hollow sections, Tubular Sections, MS Plates (any type), MS Sheet, anchore bolts for all

structural steel work etc as per drawing all confirming to latest relevant IS codes for the work of steel

structures including straightening, cutting, bending, bolting and welding the members all as per

structural drawings and as per detailed specifications (for materials & workmanship) including

necessary scaffolding/ staging etc. complete for all level all height and comprising of : i) Profile Cutting

of components to required length/ width and shape/ profile; ii) Smooth grinding/ machining of edges/

faces/ all welding joints; (Sharp corners, projections, and similar rough or sharp surfaces or edges shall

be eased and smoothed by grinding so as to provide notch free surfaces.) iii) Necessary welding

(electric arc welding) for required weld lengths and sizes. iv) Machine drilling of holes for joining/

anchoring (Standard measurements will be paid for as actual cut length used at site)

The contractor shall be submit fabrication drawings based on construction drawings (that may be

issued during construction period) for approval by the Architect/ Engineer. The fabrication work shall

18 start only after approval of the fabrication drawings submited by contractor. Any change required in 1425.00 kg 73.73

the fabrication drawings shall be carried out at No extra cost. Fabrication shall be in a perfect

architectural workmanship manner and as provided in section V & VI of IS 800 & IS 7215. Welding shall

be carried out by qualified welders/ fabricators. The procedure, selection, test and inspection shall

confirm to provisions in IS 816, IS 818, IS 822, & IS 823. Erection/ hoisting shall commence only after

passing of fabricated parts by Architect/ Engineer. Rate shall be inclusive of cutting, wastage, welding,

bending (shop at site), bolting wherever necessary, in position welding of required length, grinding,

finishing edges, filling & finishing the welded spots & gaps with grout/ sealent/ metal putty to make the

surface even and smooth, 2 coat zinc chromate yellow oxide and 2 coat of enamel paint of approved

shade etc. complete. with zinc coated nut-bolt as required for safety, structural stability of all works at

Breaking of floor for anchoring and its repair shall be also be included for this work

Providing and applying Wall painting (two coats) with plastic emulsion paint of approved brand and

manufacture on undecorated wall surface to give an even shade including throughly brushing the

surface free from mortar droppings and other foreign matter and sand papered smooth, including

applying required coats (min two coats) of white cement based putty of Birla white or equivalent after

thoughly brushing the surfaces free from mortar dropping and other foreign matter, preparing the

surface even and sand papered smooth etc, after applying every coat of putty complete. Priming

coat of alkali resistant cement primer (water or solvent based) is to be applied over prepared smooth

surface( undulation free) etc. complete as directed by engineer-in-charge. Sample to be approved

before starting of the work. The rates shall include the cost of filler for filling the cracks on surface. Extra

over item 57 for every subsequent coat of wall, ceiling or sloping roof painting with plastic emulsion pain

of approved brand.

Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) to give an required

20 shape even shade after thoroughly brushing the surface to remove all dirt, and remains of loose 515.60 SQM 122.14

powdered materials.etc complete

Providing and laying Vitrified tiles 8 to 10 mm thick , 24'' x 24'' in flooring treads of steps and landing laid

21 on a bed of 12mm thick cement mortar 1:3 (1-cement : 3-coarse sand ) finishing with flush pointing in 796.80 SQM 1120.36

Providing and laying Vitrified tiles 8 to 10 mm thick , 24'' x 24'' in skrting risers of steps and dedo on 10mm

22 thick cement plaster 1:3 (1-cement : 3-coarse sand) and jointed with white cement slurry 120.60 SQM 1195.02

Providing and laying broken chine mosaic flooring for terrace using 12 mm to 20 mm broken pieces of

glazed tiles to be laid over cement mortar 1:3 to plain or slope and to be tempered to bring mortar

23 creme out upto surface using white cement including rounding off junctions and extending them upto 380.00 SQM 779.70

15 cm along the wall,clearing with water and oxalic acid etc. as directed.

Providing & laying sandwich platform comprising of a) Sandwich of 18 mm thick single side polish kota

stone of approved size, shade and sample on top and 30 mm thick polished kota in bottom with 25mm

thick cement mortar (1:4) in between b) At centre vertical sandwich supports of 30 mm thick two kota

stone on sides and 20mm CM (1:4) in between and at both end walls vertical supports of 18 mm thick

double side kota. c) 75 mm raised platform at bottom with kota on top and 50mm CM (1:4) at bottom,

24 kota stone skirting as per design and approved sample. The rate includes rounding, champhering and 5.00 SQM 4972.23

mirror polishing of edges, facias of granite, MS support including necessary bonding adhesive (if

required) of BASF / Fosroc / BAL / Laticrete / Kerakoll make. Rate shall be also inclusive of making holes

& cutouts for SS sink, Oval wash basin, Piller tap / Bib tap etc. as directed by engineer in charge. (Only

plan area shall be measured & paid for).

Total Tender Cost in (Rs)

Executive Engineer

Contractor's Signature With Stamp Bhavnagar Area Development Authority

Bid Documents for Construction of Library Building, Fariyadka at Bhavnagar

Sr. No. Description Total Qty Unit Rate Amount

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National

1 Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps 35.00 Rmt 170.36

including making good the wall, ceiling and floor etc. complete.[A] 15 mm dia.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National

2 Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps 23.00 Rmt 208.80

including making good the wall, ceiling and floor etc. complete. (B) 20mm dia

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National

3 Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps 62.00 Rmt 253.82

including making good the wall, ceiling and floor etc. complete. ( C) 25 mm dia

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National

4 Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps 16.00 Rmt 447.72

including making good the wall, ceiling and floor etc. complete.(E) 40 mm dia

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National

5 Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps 38.00 Rmt 660.58

including making good the wall, ceiling and floor etc. complete.(F) 50 mm dia

6 Providing and fixing Gun metal check or non-return fullway wheel valve.(B) 20mm dia. 6.00 No. 203.82

7 Providing and fixing Gun metal check or non-return fullway wheel valve.(C) 25mm dia. 7.00 No. 420.63

8 Providing and fixing Gun metal check or non-return fullway wheel valve.(D) 32mm dia. 2.00 No. 314.73

9 Providing and fixing Gun metal check or non-return fullway wheel valve.(E) 40mm dia. 1.00 No. 663.43

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm diameter with jali of the following

10 nominal diameter of self cleansing design with C.I scread down or hinged grating including the cost of cutting and 12.00 No. 600.23

making good the walls.

Providing and fixing 600mmX450mm Bevelled edge designer glass mirror of superior glass mounted on 6mm th

11 A.C. sheet or plywood sheet & fixed to wooden plugs with C.P.brass screws and washers at any floor, level and 3.00 No. 859.41

Providing and fixing Urinal or approved quality including conecting the Urinal with waste pipe , tap etc.

12 complete.(A) White earthenware flat back or corner type size 430mm x 260mm x 350mm. 5.00 No. 1074.86

Providing and fixing wsh down water closet (European type, W.C. Pan) with integral P or S trap including jointing

13 the trap with soil pipe in Cement Mortar 1:1 (1-Cement : 1-fine sand) (Seal and cover to be measured and paid for 9.00 No. 1356.81

separately)(A) vitreous China Pattern :(i) in white colour

Providing and fixing water closet Squtting pan of cera, johsan, hindware brand approved make (Indian type W.C.

14 pan) size 580 mm including earthwork, bed concrete, foot rests and trap extra complete (A) Vitreous china (i) 1.00 No. 1467.68

Long patter-white colour

Providing and fixing chromium plated brass half trun flush cock of approved quality including fixing in pipe line

etc. complete.(ii) 25mm dia.

16 Providing and fixing 15mm dia C.P. bib cock of approved make specified by the Architect. 10.00 Each 400.58

Providing and fixing washbasin with single hole for pillar tap with C.I. or M.S. brackets painted white including

17 sutting holes and making good the same but excluding fittings.(A) Vitreous China:(ii) Flat Back washbasin 550 7.00 No. 1520.24

mm x v 400mm size. (i) In white colour.

Providing and fixing to wall, ceiling, floor 10Kgf/Sqcm working pressure polythelene pipes of 110mm dia. For

18 rain water , low density, complete with special flange compression type fittings, wall clips etc. making good wall 31.00 Rmt 258.23

ceiling and floor.

Providing & fixing S.W. Gully trap with C.I.grating brick masonary chamber & water tight C.I. Cover with frame

of 300x300 mm size (inside )with standard weight. Square mouth trap 100mm x 100mm size P- type

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with briocks having

croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm

intenal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of

20 frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 20mm size) 2.00 No. 2932.93

foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat

of neat cement on walls and bed concrete etc. complete.(i) Inside dimensions 455mmx 610mm and 450mm deep

for single pipe line.

Providing and fixing Kitchen sink with C.I. or M.S. brackets, painted white including cutting holes in walls and

making good the same but excluding fittings. (C) Vitreous China Sink.(i) 600mm x 450mm x 150mm size

Providing and fixing Approved SWR quality, heavy duty, uPVC pipes - Type B Ring Fit & Self Fit, Supreme or

equivalent make, Confirming to IS 13592 & Fitting confirming to IS 14735 for waste water or soil waste pipe,

with necessary specials, bends, such as `Y' junction, `T' junction (both single and double), including plugs, shoes,

cowls, flange compression type fittings, wall clips, in proper line and level with necessary support like

brackets/clamps, clips, RCC or brick pedestals or battens, if necessary, to wall, ceiling and floor, open or

concealed complete jointing with rubberising and airtight joints, with ‘T’ shaped rubber ring, etc., and lubricant or

jointing material, including testing, cutting, making good the wall, ceiling and floor, etc. Testing & installation of

pipe lines as per drawing & specification. (a) 110 mm Dia pipe

23 (b) 160 mm Dia pipe 74.00 Rmt. 834.38

Providing and laying cement concrete 1:5:10 (1 cement:5 fine sand: 10 graded stone aggregate 40 mm nomonal

24 size) bedding for stone ware pipes of following internal diameter with necessary formwork and curing complete. 11.00 Rmt. 127.16

100 dia S.W.G. pipe (112mm Ave. bed thickness)

Providing and laying cement concrete 1:5:10 (1 cement:5 fine sand: 10 graded stone aggregate 40 mm nomonal

25 size) bedding for stone ware pipes of following internal diameter with necessary formwork and curing complete. 18.00 Rmt. 213.71

150 dia S.W.G. pipe(166mm Ave. bed thickness)

Providing and laying stoneware pipes of approved quality with all fittings and fixtures and laying to the required

26 levels and gradients to the required slope including necessary excavation of trenches, laying of pipes and jointing 11.00 Rmt. 225.58

using spun yarn and caul.100 dia S.W.G. pipe

Providing and laying stoneware pipes of approved quality with all fittings and fixtures and laying to the required

27 levels and gradients to the required slope including necessary excavation of trenches, laying of pipes and jointing 18.00 Rmt. 317.48

using spun yarn and caul.150 dia S.W.G. pipe

Providing laying (to level or slopes) and jointing reinforced concrete Light duty non-pressure pipes I.S. class NP2

28 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints 62.00 Rmt. 444.61

complete.(D) 300mm

Constrcting manhole with R.C.C. top slab in 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stpme aggregate

mm. nominal size, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 Brick bats 40 + 50 mm. size) inside

plastering 15mm. thick with cement mortar 1:5 (1 cement : 5 coarse sand) finished with a floating coat of neat

cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 20mm.

29 nominal size) finished smooth complete including curing and testing. (i) Inside size 900mm. x 1200 mm. and 1.5 1.00 Each 11042.74

m. deep including C.I. cover with frame size 560mm. total weight of cover and frame to be not less than 128 kgs.

(Wt. of cover 64 kgs. and Wt. of frame 64 kgs.) (A) with 230 mm thick walls of brick masonary using bricks

having crushing strenght not less then 35 kg/sq.cm in cement motar 1 : 5 (1 cement : 5 coarse sand)

(1) A type depth 0.9 metre for 150 mm diameter sewer

Extra rate for constructing B.B masonry for every additional depth 0.10 meter or part thereof over item 24.27 (I)

for depth from 0.90 meter to 1.50 meter.

31 2) B type depth 1.50 meter for 150mm diameter sewer 1.00 Each 19349.63

Extra rate for constructing B.B masonry for every additional depth 0.10 meter or part thereof over item 24.27 (II)

for depth from 1.50 meter to 2.25 meter

SEPTIK TANK Construction Septic tank inside dimention of 3m in length & 1.5 m in width & 1.5 m depth

including excavating any type of soil as shown and mentioned in the drawing,providing and laying 0.10 m thick

plain cement concrete 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone agg.) 40 mm thick IPS flooring at bottom

with brick masonary 0.23 m thick walls CM 1:5 ( 1 cement : 5 coarse sand ) and intermediate partition CM 1:4 &

33 RCC Top slabs12 cms thick in 1:2:4 (1 cement : 2 coarse sand : 4 graded stone agg) including reinforcement as 1.00 EACH 51931.17

per design and 15 mm thick cement plaster in CM 1:4 with floating coat of neat cement slurry inside, top and

around tank below 15 cm on ground level, Also provide Two nos CI Manhole frame and cover of size 60 cm x

cm & 75 mm dia. PVC 6 kgf / Sq cm pressure air vent pipe in 3.00 length with cowl etc complete as per direction

of Engineer in charge.

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure polythene pipes of the following

34 outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making 10.00 Rmt. 280.23

good the wall ceiling and floor.(F) 75mm

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure polythene pipes of the following

35 outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making 10.00 Rmt. 258.23

good the wall ceiling and floor.(F) 50mm

36 Constructing Brick masonry road gully chamber 450mm x 450mm x 775mm with vertical gating complete. 6.00 Each 2545.86

Total Tender Cost in (Rs)

Executive Engineer

Contractor's Signature With Stamp Bhavnagar Area Development Authority

Bid Documents for Construction of Library Building, Fariyadka at Bhavnagar

Sr. No. Description Total Qty Unit Rate Amount

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV.

1 to be laid on wall with necessary clamps or in existing trench / pipe of following size of cable as per SOR 35.00 Mtr. 375.00

Specification bles (D) 3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core)

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV.

2 to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables(A) 4 core 16 Sq. 35.00 Mtr. 152.00

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable

complete with out going tails, insulating tape etc for following size of cables. (d) 4c x 16 Sq. mm.

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable

complete with out going tails, insulating tape etc for following size of cables. (C) 3 & 1/2 core 70 Sq. mm

Providing and erecting of Solderiess crimping type Aluminium / Copper lugs conforming to IS suitable for cable

5 of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass / 12.00 Nos 15.00

cadmium plated nut bolts in as approved manner. (C) 16 Sq.mm.

6 Same as above but (D) 35/50 Sq.mm. 2.00 Nos. 20.00

7 Same as above but (E) 70 Sq.mm. 2.00 Nos 25.00

Providing and fixing approved make Perforated C type cable tray. Made from CR sheet steel. The cable tray

should be single or double bended as per required and as per IS 2062/1079 and shall be coated with hot dip

8 galvanizing as per IS 2629/4509. with coupler plate / Fish plate and GI hardware like nut - bolt and washers etc. 8.00 Mtr. 420.00

erected on existing support as per Specification and as per instruction of engineer in charge as per SOR

Specification (3) 150 X 50 X 1.6 mm Thick

Providing and fixing approved make 'T' Junction for Perforated C type cable tray. Made from CR sheet steel. The

Junction should be bended as per IS 2062/1079 and shall be coated with hot dip galvanizing as per IS 2629/4509.

with coupler plate / Fish plate and GI hardware like nut - bolt and washers etc. erected on existing support as per

Specification and as per instruction of engineer in charge. (3)150 X 50 X 1.6 mm Thick '

Providing and fixing approved make '90° Elbow' for Perforated C type cable tray. Made from CR sheet steel. The

Junction should be bended as per IS 2062/1079 and shall be coated with hot dip galvanizing as per IS 2629/4509.

with coupler plate / Fish plate and GI hardware like nut - bolt and washers etc. erected on existing support as per

Specification and as per instruction of engineer in charge.. (3) 150 X 50 X 1.6 mm Thick 90° Elbow

Providing & erecting weather proof, dust & vermin proof, floor mounted front operated indoor type cubical panel

board having IP-54 protection made from 14 SWG thick CRC M.S. sheet for outer body & doors, 16 SWG thick

CRC M.S.sheet for internal partitions with necessary supporting angles, flats including cutting, bending, drilling,

welding, riveting with internal partitions & cable alley as per requirements & instruction of engineer-in-charge

with erection of supplied switch gears, BUSBARS, with suitable size of inter connecting PVC copper wire /

11 copper-aluminium strips, rubber grommets, rib, bakelite control fuses for measuring instruments, earth bus & 2.00 Sq.mtr. 10365.00

earth bolts, foundation flange - bolts-base Plates, sufficient nos. of hinged doors, handles with locking arrangement

and rubber gasket complete. The Panel shall be painted with epoxy powder coating. (The rates excludes the cost

of switchgears, bus bars, inter connecting mains & Copper Aluminium strips, meters, Fuses etc. The dimension

shall be measured excluding base beams and The rates inclued with control wiring Accessories) The panel shall be

supplied with following approved manufacturers (i) with 350mm depth

Supplying and erecting triple pole & neutral 440V/ 450V panel mounting Aluminium Busbars with four equal

Nos. of bus having current density not more than 0.8 Amp. / sq.mm (Rated current / cross section area) duly

12 wrapped with colour insulating tape for phase sequence of following current carrying capacity, erected with 1.00 R.mtr. 1027.00

necessary bus bar supports /insulators, main cable socket to each busbar,erected in existing cubical panel with

necessary connections. as per SOR Specification (B) Suitable for 200 Amp. Capacity

Providing , erecting , fabricating the M.S. structure as per requirement on site incorporating proper size of M.S.

angles, flats, bars, channels, sections complete with cutting, welding, grinding & finishing duly painted with one

coat of red oxide with erection on site as per direction of engineer in charge with necessary grouting, cementing,

plastering & finishing complete.

Supplying, erecting, testing and commissioning of approved make panel mounting type Digital Voltmeter having

14 3 digits LED display 0 to 450V AC Volts range erected on existing panel board with all connection, wiring ete., 1.00 No.. 1263.00

with manufacturers calibration certificate as per SOR Specification

Supplying, erecting, testing and commissioning of approved make panel mounting type Digital Ammeter having

digits LED display, external CT operated, calibrated for 0 to 400 Amps. suitable to operate on 450 volt AC

erected on existing panel board with all connection wiring ete., with manufacturers calibration certificate as per

SOR Specification

Supplying, erecting, testing and commissioning of Ammeter / Voltmeter selector switch for 3 phase AC supply

450V on existing panel board with necessary connections as per SOR Specification

Providing, erecting, testing and commissioning of L.T. Current Transformer with bus bar primary 50/5 to 1250/5

ratio 15 VA burden. Duly secured with insulating materials connected to the meter as per SOR Specification

Supplying and erecting approved make LED type indicator complete with all accessories and necessary

connections.(Colour as per colour code of phase (R-Y-B ) etc.

Providing and erecting metalic danger notice board for MEDIUM VOLTAGE installation to be erected as per I.S

as per SOR Specification

Approved make Three pole moulded case circuit breaker having breaking capacity ICU of 25 K.A. at 415 V

having normal current rating up to 125A. with Fixed thermal & magnetic release suitable to work on A.C. supply

50 c/s. with all internal connections & complete erected in existing 16 G.M.S. housing. ICS=100% of ICU only

(The price inclusive of TP plus Neutral link)

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986 without MCB to house

21 appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used as per SOR 2.00 Ea. 2421.00

Specification (B) three phase incoming and single phase horizontal type outgoing Per phase isolation type (PPI)

Providing & erecting of Miniature circuit breaker single pole 6A to 32A suitable to operate on 240 V A.C. system

22 and having breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark as 33.00 Nos. 111.00

per Specification

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking

23 capacity & confirms to IS :8828 in existing box having following capacity as per SOR Specification ( C ) 63 4.00 Nos. 730.00

Supplying & erecting of Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of

mA and Short Circuit withstand capacity of 6 KA and suitable for operation on single phase 240 V. having

characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component.

for following Max. rating erected as directed or as per SOR Specification (iii) 63Amps. DP

Supplying & erecting Electronic Type Cordless Call Bell erected on PVC/Metal board having portable bell push

working on D.C. & bell on 230V A.C. supply with cells / battery as per SOR Specification

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the RCC bars up to 50mm length each

26 side and pierced through a 16 Gauge M.S. box / Heavy Duty PVC box complete erected concealed in Ceiling with 2.00 Ea. 107.00

necessary finishing as per SOR Specification

Providing and erecting of 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan box as per SOR

Supply and fixing down road of G.I.Pipe 15mm dia. Heavy gauge (3.2mm or More) including cutting, threading

and painting complete

Providing and erecting of Fan clamp of 30 x 5 mm flat of required length & 10 mm M.S. 2 nos. Heavy duty

Anchor fastener erected with necessary hook of 10 mm M.S. Round Bar (D type Hook with 2 nos Anchor fastner)

30 Supply and Erecting heavy duty "D" type hook with 2 nos. heavy duty anchor fastener 2.00 Nos. 135.00

Supplying & erecting of approved make low noise decorative exhaust fan having size 200mm with 1350 RPM

with square frame ABS body with inbuilt lowers & square frame

Supply and fixing of 1200mm sweep ceiling fan with BEE 5 star rating with appx 50 to 55 watt with double ball

bearing with condenser A.C. 23OV.50 c/s.1200 mm. sweep complete, canopy and 30 cms. down rod erected on

existing hook or clamp with 24/0.2 , 3 core flexible wire with earthing.Make :-Crompton High sped plus,Orient

Energy star,Havells-50 star models make only.The Choice of colour as decided by engineer-in-charge

Supplying and erecting LED recessed mount indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt (CREE /

OSRAM / PHILIPHS make LED used in fitting ) assembled on MCPCB,Product should Suitable to replace

Conventional (2X 36W ) T-5 Light fitting with 30W LED panel Light fitting with backlit luminaire and

customised housing having dimension of [ ( 505mm (L) X 295mm (W) x 40mm (H)], suitable for retrofit into

existing cut out, made of elegantly designed CRCA powder coated housing and having Micro diffuser to provide

glare free uniform light distribution. Luminaire shall deliver excellent illumination & visual comfort with CRI of

>80, Suitable to operating voltage on 140V to 300V A.C.,Power Factor more than 0.95, THD < 15 %,CCT

K to 6500K, Luminaire efficacy> 100 lumens/watt , with external LED driver with efficiency > 85 % ( fitting

required LM-79 & LM-80 Certificates). High transmittance Micro diffuser for glare-free symmetric light

distribution. Lamps should be with 100 lm/W System Efficiency and designed for Avg. LED Life (L70 B50) of

50,000 Burning Hours & with high efficient Photo biologically safe LEDs with 3SDCM bin. Lamps should be

powered by an integral electronic constant current driver having Output Short-circuit protection, Over Voltage

protection withstand upto 440V / AC , and other reliability features as per IS: 15885 Part 2/Sec 13. Luminaire

should be provided with 4kV surge protection. Cai-III (Note:- During Execuvation of work if it reurired to cut

false ceiling for providing fitting and after erection of fitting if require to fill aditional false celling gap than that

work should be in scope of Agency.)

Supplying and erecting recessed mount LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt (CREE /

OSRAM / PHILIPHS make LED used in fitting ) assembled on MCPCB,Product should Suitable to replace

Conventional (2X 28W ) T-5 Light fitting with 40W LED panel Light with backlit luminaire and customised

housing having dimension of [ 1195mm (L) X 225mm (W)x 95mm (H)] suitable for retrofit into existing cut out,

made of elegantly designed CRCA powder coated housing and having Micro diffuser to provide glare free

uniform light distribution. Luminaire shall deliver excellent illumination & visual comfort with CRI of >80,

Suitable to operating voltage on 140V to 300V A.C.,Power Factor more than 0.95, THD < 15 %,CCT 3000 K to

6500K, Luminaire efficacy> 100 lumens/watt , with external LED driver with efficiency > 85 % ( fitting required

LM-79 & LM-80 Certificates).High transmittance Micro diffuser for glare-free symmetric light distribution.

Lamps should be with 100 lm/W System Efficacy and designed for Avg. LED Life (L70 B50) of 50,000 burning

Hours with high efficient Photo biologically safe LEDs with 3SDCM bin. Luminaire should have integrated

powered by an integral electronic constant current driver having Output Short-circuit protection withstand upto

440V/AC, Over Voltage protection, and other reliability features as per IS: 15885 Part 2/Sec 13. Luminaire should

be provided with 4kV surge protection. Cat-III (Note:- During Execuvation of work if it reurired to cut false

ceiling for providing fitting and after erection of fitting if require to fill aditional false celling gap than that work

should be in scope of Agency.)

(Point wiring in Copper Modular) Supply, Installation, Testing and Commissioning of Point wiring for Light / Bell

with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated

multistrand copper wires, in following type of pipe to be erected concealed in/ on surface on wall/ceiling

complete with 6A Modular type switch / bell push & accessories and earth continuity of following type, erected

35 on PVC / Metallic box, single mounting base frame covered with textured/metallic front plate modules erected on 81.00 Pt. 445.00

/ in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed. (a)

with medium class Rigid PVC pipe and accessories as per SOR Specification Cat :III as per SOR. The rate shall

inclued with all material. Note:-For Point wiring above 10 mtr of length additional length will be added at rate of

Supply, Installation, Testing and Commissioning of Point wiring for secondary light point with 2-1.5 sq.mm &

earthwire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper

wires, in following type of pipe to be erected concealed in / flushed on wall/ceiling, complete with earth

36 continuity and necessary connection with primary light with accessories erected on Metal / PVC box covered 57.00 Pt. 131.00

with 3 mm thick PC(Polycarbonet) / Acrylic sheet for open / concealed wiring. with necessary Lamp holder /

ceiling rose / H.D.Connector as directed. Note:- Maximum up to 6 mtrs length, excess will be considered as

Mains for Secondary Point. (a) with medium class Rigid PVC pipe and accessories as per SOR Specification.

Supply, Installation, Testing and Commissioning of Point wiring for Looped Plug with 6A Modular type switch &

37 5 pin socket erected on PVC / Metallic box, single mounting base frame covered with textured / metallic front 24.00 Pt. 255.00

plate modules erected on / in wall / ceiling with following type accessories as per SOR Specification Cat. III

Supply, Installation, Testing and Commissioning of Point wiring for FAN with 2-1.5 sq.mm & earthwire of

sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated multistrand copper wires, in

following type of pipe to be erected concealed in / flushed on wall/ceiling complete with 6A Modular type switch

and hum free EME four or more step type electronic fan regulator with separately mounted and accessories with

earth continuity of following type erected on PVC / Metallic box, single mounting base frame covered with

textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected. with necessary ceiling rose /

H.D.Connector as directed. (a) with medium class Rigid PVC pipe and accessories as per SOR Specification Cat.

Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (green) both are of

.ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected

concealed in / flushed on wall/ceiling ,complete with 6A Modular type switches and following type of accessories

erected on PVC / Metallic box, single mounting base frame covered with textured / metallic front plate modules

erected on / in wall / ceiling as per pipe erected. with necessary batten/angle holder or ceiling rose or

H.D.Connector as directed. (a) with medium class Rigid PVC pipe and accessories Cat. III

Supply, Installation, Testing and Commissioning of Point wiring for Individual Plug with & earthwire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following

type of to be erected concealed in / on surface of wall / ceiling complete with Modular type switch & 5 pin Plug

erected on PVC / Metallic box covered with appropriate front plate modules erected on / in wall / ceiling as per

pipe erected with following type of accessories. [I] For 6A Plug with 2-1.5 sq.mm Cu. Wire (a) with medium class

Rigid PVC pipe and accessories as per SOR Specification Cat.III

Same as above but [II] For 16A Plug with 2-2.5 sq.mm Cu. Wire (a) with medium class Rigid PVC pipe and

accessories as per SOR Specification Cat. III

Providing and fixing following type of Modular Type Accessories mounted with pvc / metallic box, single

42 mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. As 8.00 Nos. 25.00

desired by Engineer In chargas per SOR Specification (7) Blank Plate Single

43 Same as above (4) TV Co-axial Socket outlet as per SOR SpecificationI 7.00 Nos. 159.00

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in

44 wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with 8.00 Mtr. 24.00

following dia of pipes, in approved manner as directed (a) 20 mm

45 Same as above but for (b) 25 mm 21.00 Mtr. 33.00

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes, Check-nuts

etc. complete of following sizes. as per SOR Specification 1) 20 mm

47 Same as above but (2) 25 mm 21.00 Mtr. 21.00

Supply and erecting of Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size (a) with

medium class Rigid PVC pipe and accessories ( b) 2 Wire 1.5 sq. mm

49 Same as above but (c) 2 Wire 2.5 sq. mm 118.00 Mtr. 82.00

Supply and erecting of Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth continuity of following size (a) with medium class Rigid PVC

pipe and accessoriesas per SOR Specification (a) 2 wire 4 sq. mm

51 Same as above but (b) 2 wire 6 sq. mm 8.00 Mtr. 146.00

Providing & Erecting approved make following size of TV Co-axial flexible cable comprising inner conductor of

52 solid bare copper insulated with Foam PE & Secondary conductor made of poly - Aluminium film bonded Al. 49.00 Mtr. 39.00

Braids @ suitable coverage overall sheathed with black PVC insulation.as per SOR Specification b) RG-6

Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting

Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free G.I.Pipes having Outer pipe dia of 50mm

having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection

terminal dia of 12mm with constant ohmic value surrounded by highly conductive compound with high charge

dissipation suitable for following type of applications. (c) For Electrical Installation covering Transformer

Neutrals, Lightning arrester Earthing, A.C.Plant & Sensitive Computer System(like Automation, SCADA) i.e

independent Earthing in normal soil.Length of Pipe : 3.00 mtrs Back filling Compound :2 nos Bags of 25 Kg. as

per SOR Specification

Providing one bag of 25 Kg. Additional Back Filling Compound (BFC) suitable for safe earthing device as per

SOR Specification

Total Tender Cost in (Rs)

Executive Engineer

Contractor's Signature With Stamp Bhavnagar Area Development Authority

Bid Documents for Construction of Library Building, Fariyadka at Bhavnagar

Sr. No. Description Total Qty Unit Rate Amount

Furniture to be made

Tables (All tables should be Modular)

Table made using 19mm thick plyboard finished with 1mm thick Laminate as selected by architect. The outer edge

1 of the table to be decorated with wooden. Modesty board made of plywood finished with Laminate as above, 30.00 Sqm 10000.00

design as per architect. The Frame + legs of the table to be made of teakwood including the angled footrest. The

table to be finished with natural look melamine polish.

Tables (Top area to be measured)

Furniture to be made

Tables (All tables should be Modular)

Table made using 19mm thick plyboard finished with 1mm thick Laminate as selected by architect. The outer edge

2 of the table to be decorated with wooden. Modesty board made of plywood finished with Laminate as above, 15.00 Sqm 12000.00

design as per architect. The Frame + legs of the table to be made of teakwood including the angled footrest. The

table to be finished with natural look melamine polish.

Tables (Top area to be measured) Reception Table

Chair (Make : Premier or Equivalent)

Chair (Make : Premier or Equivalent)

Chair (Make : Premier or Equivalent)

Providing and fixing low height storage of size not more than 2100m high, fabricated out of 19mm board with

mm liner laminate on the inside. Shelves also to be lined with 0.8mm laminate from inside.

Cost of the storage units to be inclusive of brushed steel finish handles , SS hinges (W or Z), tower bolts, Shutter

magnets (Medium), locks, tower bolts, magnetic ball catch, hinge etc and all necessary hardware of approved make

all complete as per drawing and detail and as per the instructions of the architect.

All storage units to have shutters fabricated out of 18mm MDF/ 19mm Commercial Board. Double shutters to have

3" SS stoppers on top and bottom of one shutter (inside) and a lock on the other side other than the necessary

6 All laminate fixing to ensure absence of 'bubbles/etc', indicating improper finishing techniques applied; all such 30.00 Sqm 10000.00

instances, if and as/when observed, shall need to be rectified by the appropriate contractor(s), at their sole risk and

All Storages/Counters to be factory finished as per actual dimensions as on site, and fixed on site as per Architects

details/Drawings.

With Visible face including top and shutters finished in 3mm thick Veneer (natural Polish paid for separately)

Executive Engineer

Contractor's Signature With Stamp Bhavnagar Area Development Authority