SPL REPAIR TO BLDG NO P-170 (01 TO 02) OFFRS MD ACCN AT PB MARG AND PROVN OF SOAK PIT FOR EXISTING TOILET AND BATHROOM OF BAFFLE RANGE UNDER GE (WEST) BAREILLY.

Taking down cement plaster including racking out joints, hacking for key & scrubbing down with water etc as specified and directed by Engineer - in - Charge.

M&L rendering 15 mm thick in CM 1:6 on brick masonary wall surfaces or on other than fair faces of brick masonry finished even and smooth without using extra cement complete all as specified and directed.

M&L 15mm thick rendering in cement mortar 1:4 to on brick masonary wall surfaces or on other than fair faces of brick masonary fair finished without using extra cement with using water proofing liquid complete all as specified and directed

M&L 5 mm thick cement plaster on fair faces of bricks or concrete in ceiling using CM 1:4 finished even and smooth without using extra cement

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises as specified and directed by Engineer - in - Charge

M&L Non- skid coloured ceramic tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tile laying over 15 mm thick cement mortar 1:6 for floor finishes complete all as specified and directed

M & L for Glazed ceramic tiles in vertical surface 600x 300x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match coloured tile including rendering 10 mm thick CM 1:6 complete all as specified and directed

M&L for vitrified Ceramic tiles light shade 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.42 sqm but n exc 1 mtr in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement incl screeding 15mm thick in CM 1:6, complete all as specified and directed

All as Srl Item No 8 above but tiles for skriting/dado incl screeding 10mm thick in CM 1:6/rendering, complete all as specified and directed

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons Laid, bedded and pointed in any mortar etc as specified and directed by Engineer-in-Charge.

Demolition of concrete is ground floors and pavings n exc 15 cm thickness (below or above ground level) as specified and directed by Engineer-in-Charge.

Demolition of brick or stone / boulder work built in cement mortar as in quoins, arches,pillars etc

M&L for brick work with fly ash old size bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:6) complete all as spd as directed

Demolition of Reinforcement cement concrete of any description and in any position not otherwise specifically provided for, as specified and directed by Engineer - in - Charge

M&L PCC 1:2:4 type B-0 (using 12.50 mm stone aggregate) as in, levelling course with to be finished even and fair without using extra cement on roof surface / chajja (thickness of concrete will be provided as per site requirement and as directed by engr-in-charge) roof kerbs, coping, benching etc including weathering slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L for cement concrete type E2 1:5:10 (40 mm graded aggregate) as in mass concrete for sunken slab complete all specified and ditercted.

M & L for Providing water proofing treatment to RCC sunken slab as specified and directed as under:- (a) Cleaning the existing RCC sunken slab and vertical wall/RCC beam and hacking the surface. (b) 15mm thick plastering over the floor & vertical surface in CM 1:4, mixed with liquid water proofing compound @ 200ml per 50 kg of cement trowelled to even and smooth finish without using extra cement .(Water proofing compound shall be measured and paid separately). (c ) filling the sunken portion with water for 72 hrs and carring out the ponding test.(Any leakage /seapage noticed shall be repaired). (d) Applying two coats of elastomaric acrylic water proof coating per sqm in each coat with roller application.(Note: Each coat of elastomaric acrylic compound requires 6-8hrs to dry up itself second coat shall be applied on getting the first coat completely dried up.) (NOTE: Water proofing compound shall be measured and paid separately under respective item)

Supply only liquid water proofing compound all as specified and directed

M&L for 25 mm thick cement concrete type B0, 1:2:4 (using 12.5 mm graded stone aggregate) in floors, finished rough to receive floor tiles complete all as specified and directed

Taking down chowkats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) removing from site complete all as specified and directed by Engineer-in-Charge.

S&F powder coated aluminium Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.)on each shutter. hinges type B-21 100mm long (2 no.) suitable handle (1 no.) tower bolt 100mm long (01 no) in each shutter complete all as specified (Thickness or powder coating not less than 50 micron) complete all as specified and directed by Engineer-in-Charge. (Note:-Both Wire Mesh Shutter and Glass Shutter shall be measured and paid as one unit only)

S&F powder coated aluminium frame for windows, ventilators and kitchen cupboards, doors frame size 150x44mm and 2mm thick with one or more rebates including joining cleat for fixing etc and add for powder coating (minimum thickness of powder coating 50 micron) complete all as specified. Note : Weight of section should not less than 1.12 kg per RM.

S&F for mild steel window grills box type framed work as in window guard bars, grills or forged into spikes, framed balusters, walkway railing and similar work including welding, FE-290 grade E-165 complete all as specfied and directed.

Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) removing from site complete all as specified and directed by Engineer-in-Charge.

S & F Pressed steel frames size 106 x 60 mm x 1.25mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed by Engineer-in-Charge.

S & F Pressed steel frames size 125 x 60 mm 1.25mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed by Engineer-in-Charge.

S&F for 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 35mm thick Glazed and skeleton shutters, open rebated of saal wood second class hard wood rail and stles and prepared to receive glass, gauze, etc. (without sash bars), divided into squared, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers sizes of members of shutters as specified in SSR Part I, Section 8. cla-use 8.20 (a); supplied and fitted to chowkats complete all as specified and directed by Engineer-in-Charge. (Note :- S & F Glass/gauge shall be measured and paid for separately)

S & F Solid Prelam WPC solid Door Frame of size 105mm x 65 mm, density more than 0.95, moulded preleminated fixing at opening with screw of size 100 mm long 5 mm dia pling & fixing in opening as per specification and directed Note : Colour to be decided by GE

S&F 30 mm thick solid core one WPC Modular door, one side Prelam and other side plain fixed in the frame at site as per specification & drawing.

S&F stainless steel wire cloth, 0.56 mm nominal dia of wire and average with of aperture 1.18 mm and fixed with stainless steel wire staples and over stainless steel chicken wiremesh(pitch length 0.25mm) complete all as specified and directed by Engineer-in-Charge.

S&F for steel ventilators with top fixed type, with glazing bars complete welded including one shop coat of Red Oxide Zinc chromate primer complete all as specified and directed by Engineer-in-Charge. (Note :- Glass shall be measured and paid for separately).

Taking up or down 15 mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed by Engr-in-Charge

Taking up or down 20 mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed by Engr-in-Charge

S&F 15 mm dia steel water tubing galvanized medium grade concealed in all type wall with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge

S&F 20 mm dia steel water tubing, galvanized, medium gradeconcealed in all type wall with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed.

S&F in repairs factory made PVC Cupboard frame of the size 75mm x 40mm with a wall thickness of 5mm, made out of extruded 5mm thick plain/prelam PVC sheet of density 600 kg/cbm, having bottom width of 50mm and thickness of 10mm. All four frame lengths reinforced with 15 mm x 15mm M. S. square tubes of 19 gauge thickness throughout the frame and mitre cut at two corners adjointed with 2 nos. of 15mm long brackets 0f 10mm x10mm M S square tubes. The door frame shall be fixed to the wall using 8/100 long M S screws through the frame by using PVC fasteners. A minimum of 4 nos. of screws to be provided for each vertical member and minimum of 2nos. of screws to be provided horizontal member etc. complete as per direction of Engr-in-Charge, manufacturer's specification and drawing.

S&F in repairs factory made PVC cupboard flush type shutter of 30mm thick consisting of frame made out M S tubes of 19 gauge thickness and size 19mm x 19mm for stiles and rails. The inside panel shall consist of 20 mm thick multichamber hollow PVC section of 1mm wall thickness, bonded using solvent cement/ cynoacrylate adhesive with 5mm thick plain/prelam PVC sheet, on both side of inside panel incliding necessary items to fix the shuter to frame such as 100mm stailess steel hinges, 100 mm long handles made of anodised aluminium and magnetic ball catch for each pair of shutter.All four edges of the panel to be sealed with lipping of 10mm thick and 20mm wide PVC sheet baton (made by sticking 2nos. PVC foam sheet of 5mm thickness using PVC solvent cement adhesive). complete as per direction of Engr-in-Charge.

S&F in repairs PVC boards 19/20 mm thick any colour/ prelaminated as in cabinets incl shelves and shutters, fixed with screws and adhessive as per direction of Engr-in-Charge and, manufacturer's instructions including piano hinges, magnet catcher, handles etc.

M & L for glass shelf in good quality (10 to 12 mm thick) with necessary brackets fixed in wall to hold the glass shelf complete all as spd and directed

S&F 200 mm long Stainless Steel glossy finish handles with SS screw, complete all as specified and as directed

S & F hydraulic concealed hinge with clip on installation and integrated Silent System, opening angle not less than 100º, For shutter thickness 15 - 24 mm full overlay type shutters, hinge cup dia 35 mm including necessary fixing arrangement with SS screw complete all as specified & directed.

Dismantling water tanks 250 & n exc 500 and removing to store of all retrieved material ) complete all as specified and directed

S&F 1000 litres, rotational moulded polyethylene of white colour in tripple layer water storage tank (cylindrical vertical with closed top with suitable size of M S Tasla with suitable locking system ), hoisted and fixed in position complete all as specified and directed

M&L for Granite (of any type) tiles 20mm thick machine cut and machine, polished,and moulding, window cills, riser of steps and urinal partition wash basin platforms and flooring,skirting/dados, kitchen like in cement mortar(1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of marble and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of marble laid over cement screed and jointed with grey cement slurry mixed with pigment to match including rubbing & mirror polishing ding and inclucding 10mm thick cement plaster on brick surfaces or concrete surface in cm (1:4) finished even and rough as screed complete all as spd and directed.

M & L for 75mm thick PCC 1:3:6 , type C-2 using 40 mm graded stone aggregate as in plinth protection laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. Exposed surfaces finished even and smooth without using extra cement including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed .

M&L for reinforced cement concrete 1:1.5:3 type A-1 (using 20mm graded stone aggregate) (nominal mix) as in slabs supported on wall,landing, balconies, shelves and like including bonding agent , complete all as specified (reinforcement to be measured & paid under respective items).

M&L for reinforced cement concrete 1:1.5:3 type A-1 (using 20mm graded stone aggregate) (nominal mix) as in Lintel/Roof beam and chajja including bonding agent , complete all as specified (reinforcement to be measured & paid under respective items).

S&F Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) completed all as specified and directed.

S&F Form work to sides and soffits of floor or roof beam, beam hings, girders bressume, lintles, contilevers, shelves,Chajjas including support over lungs etc also splays between floor and beams etc. completed all as specified and directed.

Supply and fix TMT bars, 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) but not less than 0.9 mm dia conforming to Fe-410 - 0, complete all as specified.

S&F Mild steel TMT bars 5mm dia and over upto and including 10 mm dia in stirrups,spaces and binders and all as specified and directed.

S & F 140 mm long floor door stopper of aluminium alloy body and tongue, brass body and tongue with hard drawn steel spring as specified and directed by Engineer-in-Charge.

M&L for stainless steel (AISI 304 Grade ) Non magnetic multilayer nikle chrome plated for multipurpose utensil container including frame work telecscopic channels, handles etc as reqd and complete all as specified and as dircted utensil sample, design and pattern of each basket to be approved by GE the foloowing size in each kitchen. (a) plain basket 510x470x100mm or 520x485x100mm or 530x505x150mm slace godrej code 6126 Baan code LKY2PB 2014 -Evershine size 520x485x90mm of 03 nos (b) multisize plate basket of size 510x470x150mm or 520x485x150mm or 436x500x200mm (Clear depth 500mm) 02 nos make Silk Elnora BAAN code LKY-3CS214- Ever shine size 520x485x90mm approved by GE (c) Cutlery Basket, with Perforated bottom and side of compacted -slots for holding cutlery of size 510x470x100mm or 520x485x100mm or 144x468x50 (Clear dpth of 500mm) 02 nos make Silk Elenora (Asian Paint) code 600, size 530x505x100mm (Godrej Product code 6134 BAAN Code LKY2PC214/Ever shine size 520x485x95mm (d) Plain basket of size 510x470x200mm or 520x485x200mm or 486x500x200mm 02 Nos make Silk Elenora (Asian Paint) code 600, size 53x505x200mm- Godrej product code 6128 BAAN code LKY 2PB218- Evershine size 520x485x180mm (e) pull out with 2 basket each of size 150x485x80mm or 100x485x80mm 01 Nos make Sleek Elenora (Asian Paint ) code 250 size 180x500x590mm / Godrej product code 6141 baan code LKYNS2SP6/Ever shine size 610x485x90mm (f) dust bin as reqd 01 Nos Make 200 series of Hettich

S & F 150 mm thick aluminium, anodised, barrel tower bolts of extruded section and fixed

S&F 150mm size aluminium handles, cast type anodised completed all as specified and directed.

S&F 100 mm size butt hinges medium weight stailess steel complete all as specified and directed by Engineer-in-Charge.

S&F 200 mm size ordinary mild steel , rat tailed rod pattern spring including roller and roller plate welded to mild steel frame.fixed in repair complete all as spd & directed.

S&F 20mm bore ball brass valve high pressure with polythene float and fly nut complete, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repairs Vitreous China table/counter top wash basin of suitable size including SS bottle trap, and cabinet of PVC shutter fixing on counter with SS waste coupling, cp mixer for hot & cold waste pipe complete all as specified and as directed. Model : Cat No 91072 Orchid of Hindware , Parryware Cat No C0483, Cera Cat No Chauvin S2020166.

S & F in repair fancy type 150mm size square brass CP shower rose with or without swivel joints complete all as specified and as directed.

S&F in repairs brass chromium plated wall mixer 3 in 1, 15mm for mixing hot & cold water screwd down three joints to steel pipes or unions and plugging and screwed to walls complete all as specified and as directed.

S&F in repair 15 mm dia bib tap fancy type chromium plated with flange quarter turn complete all as specified and directed.

S&F in repairs Bib tap (15 mm)standard of PTMT any colour high pressure screwed for iron pipe and screwed (min weight 90 gms)

S&F in repairs angle valve (15 mm)standard of PTMT any colour high pressure screwed for iron pipe and screwed (min weight 90 gms)

S&F fancy type chromium plated brass two way bib cock suitable for 15mm bore pipe complete all as specified and directed.

S&F stainless steel of AE- SI 316 grade tubular towel rack including a pair of CP brass bracket complete all as specified and directed.

S&F in repairs 15mm bore PVC connections, with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair fancy type brass chromium plated soap dish of 160x160x90 mm , complete all as specified (

S&F in repair fancy type chromium plated brass angle valve type suitable for 15mm bore pipe complete all as specified and directed.

S&F in repairs of 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified

S&F in repair 15 mm dia fancy type stop cock/concealed cock , chromium plated with long shank and cup (conncelaed type)for iron pipe or for unions and fixed complete all as specified.

S&F in repair vitreous china squatting pan of orrissa pattern long pan size 580 x 440 mm white with "P"or "S" trap size 100 mm dia front or back inlet and integral foot rest any pattern (excluding flushing cistern and flush pipe) including provn of lime concrete bedding complete all as specified.

S&F in repairs Vitreous china wash down water closet single piece (Cascade pattern) with seamless flushing cistern square design duroplast slim seat cover, slow falling seat cover size 69x37x73CM / 66x35x71 complete, including connection to drain pipe etc complete all as specified and directed.

S&F in repairs, PVC low level cistern 10 litres capacity, valve less, symphonic action type with float, handle including 32mm dia PVC flush pipe of polyethylene of low or high density & bracket etc complete all as specified and directed

S & F Brass CP hand shower (health faucet) with 8mm Dia 1.0 Meter Long Flexible Tube and Wall Hook screwecd for iron pipe fancy type long body all as specified and directed

S & F in repair water Jet of EWC chromium plated with PVC connection fixed at water closet single piece seat complete all as specified and directed

S&F in repair PVC (SWR) floor trap with CP grating including jointing with solvent cement floor trap 75 mm dia outlet plain with grating including jointing to waste pipe fixed in cement concrete 1:2:4, type B-1 complete all as specified and directed.

Dismantling of cast iron /PVC/AC/SGSW pipes 100mm dia jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.

S&F PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floor with necessary fitting complete all as specified and directed by Engr-in-charge.

S&F PVC (SWR) 110mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floor with necessary fittingcomplete all as specified and directed.

S&F PVC (SWR) 110mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) 75mm bore bends any radius complete all as specified and directed.

S&F in repairs Stainless Steel plate rack of size 90x80x25cm made with 1.00 mm thick sheet including taking out existing wooden plat rack, complete all as specified.

S & F in repair 0.8 mm thick stainless steel kitchen sink size 590x460x230mm undermount, double bowl size 540x410x230 mm) , incl waste pipe & SS coupling, washers etc. complete all necessary fittings all as specified and as directed

S&F in repair 20 mm dia stainless steel 1.0 mm thick fancy type curtain droppery rod with decorative design matching brackets as approved and knobs (lattu) or end bracket as required incl fitting with 80 mm long SS screw with 75 mm long wooden gitty of appropriate c/s in each end & intermediate support complete all as specified and as directed

S & F Brass CP Hand Shower with 15mm dia 1.2 Meter long flexible tube and wall hook screwecd for iron pipe fancy type long body complete all as specified and directed. Model No :- HSH-1931 of Jaquar , Hindware Model No F160053, Parryware Model No T9982A1, Cera Cat No F7030102AB)

S & F for Toilet paper holder, vitreous China, Chromium plated with flap guard fixed with screwed in wall as spd and directed

S & F for glass corner shelf in Bathroom 225 x 225 mm with chromium brackets and fixed with screwed in bathroom corners as spd and directed

M & L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, Chajja ( up to IInd floor) etc making good, cutting exc 10cm and not exc 40cm girth in brick walls complete all as specified and as directed.

M&L for preparing newly plastered walls surfaces and applying two coats of exterior weather emulsion paint over and including 1mm thick wall care putty complete all as specified and directed.

M&L for complete removal of existing treatment on walls etc including cleaning of any mortar drops, fungus efflorescent salts etc and preparation of old plastered surfaces and applying two coats of exterior weather emulsion paint over and including 1mm thick wall care putty complete all as specified and directed.

M&L for preparing newly plastered walls surfaces and applying two coats of oil bound distemper over and including 1mm thick wall care putty complete all as specified and directed.

M&L Preparation of newely plaster surfaces and applying two coat of oil bound distemper over and including 1mm thick wall care putty on ceilings complete all as specified & directed by Engr-in-Charge.

M&L for complete removal of existing treatment on walls etc including cleaning of any mortar drops, fungus efflorescent salts etc and preparation of old plastered surfaces and applying two coats of oil bound distemper over and including 1mm thick wall care putty complete all as specified and directed.

M&L for preparation of new untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over and including one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

M& L for Preparation of new iron surface and two coat of synthetic enamel paint ovar a coat of red oxide primer complete all as specified and directed.

Dismantling of roof terracing cement / brick concrete (un-reinforced) and existing water proofing treatment of any thickness in any position and of any portion from top of roof of building, cleaning surface of roof with wire brush / mechanical brush and with water thoroughly to remove all dust / dirt and loose particles to expose base concrete roof slab and removal of rubbish / demolished material out of MD land complete all as specified.

M&L 25mm thick cement concrete type B1 1:2:4 using 20mm graded stone aggregate in roof finishes even and fair to receive water proofing

Supply and providing water proofing treatment with polymeric standard water proofing membrane 3 mm thick having 10 years guarantee for water tightness all as specified and directed and described as under : (a) Prepartion of RCC roof surface and applying one coat of polymeric modified bitumen 85/25 @ 1.2 Kg/Sqm over a coat of polymeric primer @ 0.30 Kg/Sqm including cleaning surface, all as per manufacture's specification complete all as specified and directed. (b) Supply & Providing APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced/ torch application of membrane with 10 cm overlaps as required thereof, complete all as specified or as directed. Make :- IWL Hyperplas Polyster (M/S IWL), Super Thermolay (M/S STP Limited), Torch Shield AP by Pidilite Industries.

M & L for applying one coats of Bitumen based UV reflective and water proofing paint with aluminium finish over APP membrane and maximum coverage 8.00 Sqm per litre per coat on non assessible roof over APP membrance complete all as specified.

M&L for Providing & injecting chemical for post construction ATT along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc in a portion with cement mortar 1:2 to match the existing apron complete all as specified and directed.

M & L for Post Construction anti termiteTreatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor soil complete as specified and directed.

M & L for 15 mm thick full bull nosing, fully vitrified step tiles as riser & steps and skirting in full length in single piece with 3 to 4 embossing line of stair width laid cement screed and jointed with grey cement slurry mixed with pigment to match the shade complete all as specified and directed.

Returning, filing in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in soft/loose soil, complete all as specified and directed.

M&L 15mm thick rendering on walls brick or concrete surfaces in cement mortar 1:4 with water proofing compound, incl finish even and smooth w/o using extra. cement.

M&L for rubber molded cement concrete factory made coloured glazed interlocking paver block any shape and size confirming to IS 15658 -2006 of 80mm thickness, M-35 Grade, pattern and colour as approved by GE and over and inclduing 100 mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base floor / pavings all completed as specified and directed.

M&L Sand filling under floors or in foundation 25 mm thick including watering and consolidation complete all as spd

M & L Providing cement concrete type B0 1:2:4 using 12.5mm agg in kerbs or mud stops rounded edges completed all as specified and directed

Dismantling timber scantlings 40 Sqcm and over in section, in any position , framed work complete all as specified and directed.

Dismantling asbestos cement (corrugated, semi corrugated etc) sheets in roof coverings complete all as specified and directed.

M & L for Steel work in tubular hollow rectangular trusses, purlins, rail including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade inluding one coat of zinc chromate primer before fabrication distance pieces, cleats etc GDE Fe 410-S. complete all as specified and directed.

S & F Pre-painted galvalume aluminium zinc coating GI based semi corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M & L for Preparation of Old Plaster surfaces and applying two coats of oil bound distemper over and including 1mm thick wall care putty on ceilings complete all as specified and directed.

M & L for Excavating over areas, n exc 1.5 m deep and getting out in soft/ loose soil all as specified and directed.

M & L for Excavating over areas, exc 1.5 m deep and n exc 3.0 m deep & getting out in soft/ loose soil all as specified and directed.

M & L Hardcore with broken bricks of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface thick watered and rammed/rolled to a true surface to achieve required density complete all as specified.

M&L PCC 1:4:8, type D2 (using 40 mm crushed stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed.

M & L Brick work with fly ash bricks, old size bricks, straight or curved on plan exc 6m mean radius built in CM 1:4 complete all as specified and as directed.

M & L Brick work with fly ash bricks, old size bricks, in one brick thick or one & half thick brick walling straight or curved on plan built in CM 1:4 complete all as specified and as directed.

M & L TMT bars 6 to 8 mm dia, cut length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & as directed .

M&L for reinforcemen cement concrete (Nominal mix) type B1 using 20 mm graded stone aggregate as in slabs supported on walls/ beams, deck slabs, manhole cover , beams/bands columns etc including necessary form work and scoffolding complete all as specified and as directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded aggregate as in cills, coping, benching, hunching, steps, bed blocks, tank staging, sesmic and other similar courses, lacing courses parapet and railing upto 60cm ht kneeler kerb and a like including weathering, slightly rounded or chemfered angle and throating as directed.

M & L for 150 mm dia Reinforced concrete pipes, class NP2, laid and jointed complete with collars laid in trenches and joints incl providing PCC (1:3:6) type C-2 using 40 mm graded stone aggregate as in bed of NP-2 drain pipe 150 mm bore including packing under and completely surrounding the pipes after they are laid and tested complete all as specified and directed.

Cutting into existing manholes for connecting new drains internal dai of 150 mm bore NP-2 pipes, making good to pipe and rendering, cutting out existing benching for forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished complete all as specified and directed.

Removing of execavated material n exc 50m and depositing where directed at a level n exc 1.5 mtr above the starting point.

Internal & External E/M

Taking down carefully aluminium point wiring any type including battens if any except for ceiling or where not feasible for light/ fan//bell/socket or power and including unscrewing from board, fitting and fixture such as switches,socket, ceiling rose,lamp holder,pendants, bracket and regulator etc and removing material from site including making good disturbed surface to match with the existing surface complete all as specified.

Taking down carefully UNSV main switch DBs of any description of an size in any position complete all as specified.

Taking down submain wiring including all accessories complete all as specified and directed.

Material and labour for point wiring with single core FRLS 1100 volt grade cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium duty ISI marked not less than 20mm dia, with all conduit accessories, screws (concealed conduit wiring in walls and casing capping on ceiling or roof) including metal box suitable for modular fittings and covered with modular plate and cover of suitable size with new brass screws for mounting switch sockets and regulators and drawing continuous earth wire with and including PVC sheathed 1100 Volts grade cable with stranded copper conductor of size 1.5 Sq mm (Nominal area) and connected to main earth dolly complete all as specified for:- (a) One light / fan/ exhaust fan point controlled by one switch.

All as Srl Item No 134 above but for (b) One 5 pin 5 Amp switch socket out let point on an independent board.

All as Srl Item No 134 above but for (c) One 5 pin 5 Amp socket out let point controlled by one switch on same board.

All as Srl Item No 134 above but for (d) One buzzer/ bell point controlled by one push button on the same board with other switches or independent

All as Srl Item No 134 above but for (e) One light point controlled by two 2 - way switches , on indepndent board.

All as Srl Item No 134 above but for one 15 Amp 6 Pin switch socket out let independent with 2.5 Sqmm FRLS (Nominal Area) PVC unsheathed copper conductor single core multistranded incl 2.5 sq mm FRLS PVC copper conductor single core used as earth continuity conductoe complete all as specified and directed.

S & F Modular switch one way 6 A, 1 Module complete all as specified and directed by the Engr-in-Charge.

S & F Modular switch one way 16 A, 1 Module complete all as specified and directed by the Engr-in-Charge.

S & F Modular switch Two way 6 A, 1 Module complete all as specified and directed by the Engr-in-Charge.

S & F Modular bell push 6 Amp, 1 Module complete all as specified and directed by the Engr-in-Charge.

S & F Modular Socket 6 Amp, 2/3 Pin combined 2 Module complete all as specified and directed by the Engr-in-Charge.

S & F Modular Socket 6/16 Amp, 2/3 Pin combined 2 Module complete all as specified and directed by the Engr-in-Charge.

S & F Modular fan regulator Step up type, 120 Watt, 2 Module complete all as specified and directed by the Engr-in-Charge.

Supply and Fixing ceiling rose PVC / Poly carbonate, Isolated body, three terminal AC 230 volts complete all as specified and directed.

M & L for replacement of lamp holder, PVC / Poly carbonate, insulated body modular type with back plate batten/angle type for batten fittings complete all as specified and & directed

S&F in replacement LED mirror light fitting of 1 x 10 watt LED batten with aluminium housing with all accessories prewired suitable for wall /surface mounting complete with connection all as specified and directed.

S&F in replacement LED mirror light fitting of 1 x 20 watt LED batten with aluminium housing with all accessories prewired suitable for wall /surface mounting complete with connection all as specified and directed.

Supply and fixing in repairs surface mounting LED slim square down lighter made of PDC Al with high efficint LEDs and glare free opal diffuser, IP 20 12 watt 220 volts AC complete with drivers, holders,LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete

S&F in repairs indoor decorative LED City-3 light fitting suitable for & including single 12 Watt LED lamp with polycarbonate body with upper globe complete all as specified and directed.

Supply and Fix in repairs LED lamp 12 Watt, 230 V , AC integrated circuit complete all as specified and directed.

Supply and fixing in repairs Buzzer, Ding Dong AC. 230 volts,single pole

Supply & Fixing in repairs security light fitting, LED type, 25 Watt, 6000 K, pressure die cast housing with prismatic polycarbonate diffuser & indvl LEDs as light source with integrated electronic driver complete with M&L GI pipe mounting bracket of size 25/32 mm dia and 1.20 m long fixed to wall with and including nut, bolts and GI clamps of size 50 x 6 mm as required including two coats of synthetic enameled paint over a coat of primer and making connection with three core 23/.0076 rubber insulated copper cable from ceiling rose to connector of street light complete all as specified and directed.

M&L for sub main wiring with two single core 6.0 Sqmm (FRLS) copper conductor PVC unsheathed cable medium grade including PVC conduit (appropriate size) concealed in wall for sub main connection including 6.0 Sqmm (FRLS) PVC insulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly all as specified. ( Note :- Two runs of 6.0 sqmm (FRLS) and one run of 6.0 sqmm (FRLS) copper conductor shall be measured as one unit length.)

S & F of 1100 volts grade heavy duty two single core 4 Sqmm size (Nominal Area) PVC insulated (FRLS) copper multi-stranded conductor cable as in sub main wiring, drawn into & including PVC conduit medium grade not less than 20 mm dia including its all accessories & fittings, fixed concealed with and including chase cutting and making good the same as per existing specifications along with a continuous run of 4 Sqmm size (Nominal size) stranded copper conductor PVC insulated (FRLS) (green colour) cable as earth wire complete all as specified and directed. NOTE: - TWO SINGLE CORE CABLES ALONG WITH EARTH WIRE AND PVC CONDUIT SHALL BE MEASURED AS ONE UNIT LENGTH.

Taking down carefully ceiling fan from existing site and carry out servicing by opening the motor , removing/ cleaning the dust from complete body , oiling greasing complete incl one coat of white enamel paint in complete fan and lovers.wall or as reqd at site all as directed by Engineer-in-Charge.

Taking down carefully exhaust fan with lovers from existing site and carry out servicing by opening the motor , removing/ cleaning the dust from complete body , oiling greasing complete incl one coat of smoke grey enamel paint in complete fan and lovers .Cutting of wall in appropriate size for fixing of exhaust fan and making good the surfaces of wall and make the fixing arrangement with grouting four Nos fully threaded bolts on wall or as reqd at site all as directed by Engineer-in-Charge.

Taking down carefully Geyser from existing site and carry out servicing by opening , removing/ cleaning the dust from complete body , complete incl one coat of smoke grey enamel paint complete geyser and making good the surfaces of wall and make the fixing arrangement with grouting four Nos fully threaded bolts on wall or as reqd at site all as directed by Engineer-in-Charge.

S&F in repairs MCB SPN 40 Amp 240 volt complete all as specified and directed by the Engr-in-Charge.

S&F in repairs MCB single pole 6 to 32 Amp 240 Volt 'B' curve 10 KA complete all as specified and directed by the Engr-in-Charge.

S&F in repairs MCCB Triple pole and neutral 100 Amps 415 Volt curve 10 KA complete all as specified and directed by the Engr-in-Charge.

Supply and fix flush sheet metal enclosure SPN DB 8 way with double door IP-42 protection detachable gland plates, flush mounting for MCB fitted with bus bar , earth bar and neutral links complete all as specified and directed.

S & F in repairs Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps

Taking down carefully electric/electronic meter and fixing the same after bldg repair all as directed by Engineer-in-Charge.

Supply and fix TPN DB -VTPN DB 4 way with provn of MCCB 160 Amps , 415 Volt, 3 Phase, 4 wire AC 50 Hz having aluminium Bas Bar phase and the neutral insulated with PVC sleeves, connected with appropriate size copper thimbles.

Material & Labour for earthing complete including taking out old unsv and replace with galvanised steel earth plate 600x600x 6mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 meters below normal ground level, surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate using 4 mm dia GI wire as earth wire electrode moulded and rivetted to earth plate at one end and connected to main switch/ control switches of buildings at another end, GI earth wire encased in and including 15 mm dia GI 'light grade' pipe from upper end of earth plate upto main switch board of building including 20 dia bore GI pipe 'light grade' as water pipe from earth chamber and including excavation and earth work, PCC 1:3:6 type C1 chamber and MS angle iron frame 40x40x3mm and RCC cover 40mm thick (1:2:4) type B1 using 20mm graded stone aggregate reinforced all as specified

Taking down carefully service connections of any description from pole, wall or service brackets etc including making good disturbed surface to match with the existing surface complete all as specified.

Supply and laying & testing UG cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (Heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm, 3.5 core. complete all as specified.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth and getting out in soft/loose soil for laying of LT UG cables/base for Pole etc complete all as specified.

M&L for sand cushioning laid in trenches for laying of LT UG cables complete all as specified.

M&L Modular bricks common burnt clay building bricks, sub-class ‘B’ designation-75 for LT UG cable protection complete all as spd and directed.

S&F GI tubes light grade of dia 80 mm with all fitting and fixed complete for protection of LT UG Cables laid to walls or in floors or along with poles etc complete all as spd and directed.

Notes:- Tenderers may note that amount as given in schedule of credit will be deducted from the total amount to worked out the net contract sum at the time of Acceptance of tender.

Please Enable Macros to View BoQ information