07 Webel IDM BN4 AUDI 20 21 18

Amount

Full Height (70 to 75mm thk.) modular (Fully solid partition with acoustic Pre-Laminated tiles & glass wool) system aluminium partition:

1a) Providing , fixing & Supplying Full Height (70 to 75mm thk.) modular (Partly solid and partly glazed or fully solid partition with acoustic Pre-Laminated tiles & glass wool (Only glass wool to be paid separately) system aluminium partition product should be manufacturing as per specifications given below: All aluminium or metallic parts section made from (aluminium alloy 63400-WP or IS: 733 & IS IS: 733 & 1285:2002) shall undergo a 8-10 stages anti rust treatment and shall be powder coated with Epoxy polyester in Glossy finish to a thickness of 60 to 70 microns. The frame structure is made by joining different Extrusions (Refer Assembly guide lines for Sections details) by means of brackets made of 3 mm Thk HR (IS-2062) and screws as per elevations defined by client. All the hardware items should be as per BIFMA / ANSI standards. All other items as per IS standards. All modular partitions shall be mounted on floor gaskets made of rubber / PVC to provide gripping with the floors. Each frame shall be provided with minimum two or more 12mm levelling bolts which allow 40 to 50mm adjustment for floor unevenness as well as false ceiling height difference (up to 15 mm). Provision for Horizontal adjustment is given between Side track inner and side track outer extrusion at wall side with adjustment up to 20 mm. The super structure above false ceiling level consist of True ceiling bracket ,False ceiling bracket which holds wooden (hard wood) batten frame or aluminium extrusions used for fixing Top beam inner extrusion. The levellers shall be concealed inside the skirting.

1b) The main vertical member of the frame bearing the load of brackets and storages shall be made of minimum 2.5mm thick Aluminium Section (aluminium alloy 63400-WP or IS: 733 & IS IS: 733 & 1285:2002). The horizontal members shall be made of minimum 1.5mm thick Aluminium Section. The thickness of the frame shall be minimum 70 to 75mm inside. The thickness of trims and tiles shall not be considered while measuring the thickness of the frame. The frames shall be in the form of prefabricated modular structures. Frames can have 1-4 modules in prefabricated form. Additional height shall be achieved by mounting modules over them. The bottom module shall be mounted over a skirting of 85mm height. The skirting shall be designed so that switches can be provided on the skirting level. All the modules shall be of the same height. The frames shall have prefabricated slots for vertical and horizontal passage of wires. The frames shall also have prefabricated slots for fixing brackets used to support worktops, overhead hampers, gable ends, etc. TILES: The tiles shall be made of 1.5 thick steel tiles on both sides.

1c) ACCOUSTIC PRELAM MDF (One side decorative lamination other side balancing lamination as per requirement) Prelam tiles (both side of partition) are made of 8mm thick MDF board (IS: 14587-1998 ) , the cut edges of tiles are covered with 0.5 mm thick PVC lipping. Medium density fibre board conforming to IS: 14587-1998 for prelaminated made of wood fibre bonded with Urea formaldehyde for interior grade. glass wool of 50mm thick having density of 48 Kg per cum. to be inserted into the pre - fabricated slot covered the glass wool by marking cloths treated with Naptha @ 0.07 Ltr.per Sq.m. of cloths for acoustic purpose (Only glass wool to be paid separately). ACCOUSTIC FABRIC TILES (both side of partition): All Fabric tiles shall be made of 1.5 to 2mm thick galvanized steel (Grade of Zinc Coaling 350g/sqm) as per IS code 277) tiles warped with fabric by default, so that there should not be any development of fungus in future. Fabric is pasted on them by PVA glue. It should be possible to replace the fabric by peeling it off. GLASS TILES: The glass tiles (both side of partition) shall be made of 5mm thick (IS-2835) Clear toughened glass either. ACCOUSTIC PINUP TILES: The pinup tiles shall be made of polypropylene sheet encased in 0.80mm thk CRCA steel (IS-513 CR1) (powder coated with Epoxy polyester in Glossy finish to a thickness of 40 to 60 microns after 7-8 tanks anti rust treatment of surface)/ GI (Grade of Zinc Coaling 350g/sqm as per IS code 277) sheet of 0.8mm thickness. The casing thickness shall be 7mm. Fabric shall be pasted over the polypropylene sheet by PVA glue. The total thickness of the tile including the stiffeners shall be 10-12mm.

1d) MARKER TILES: The marker tiles shall be made of 4mm thick toughened glass painted from Inside, which act as a glass marker tiles. ACCESSORY TILES: The accessory tile (both side of partition) ) shall be made of Aluminium extrusion of 1.2mm thickness. The tile shall have horizontal recesses of 6mm width and 3mm depth at a distance of 27mm from each other over the entire surface of the tile. The recesses shall be used to hang accessories such as Paper Tray, Binder Bin, Telephone Holder, Bottle holder, Utility trays, etc. as per requirement. The products should be tested as per BIFMA standards for at least ten years. The product should have ISO-9001:2015, ISO-14001:2015, ISO-18001:2015, OHSAS 18001:2007 certifications. Energy management system as per ISO-50001-2011, in accordance with the TÜV NORD CERT auditing and -certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and Should have Green Guard, FIRA Certification for few of its products. The above modular partition should be as per specification and sample approved by client. Size of Tile of width-300 to 600mm, Tiles Ht-150 to 600,750mm. All the exposed partition paned edges shall be fixed with aluminium extrude box shape powder coated trims. Ends must be covered with Die cast aluminium. The rate shall include all design, any support (if required) above false ceiling for fixing the partition, Engineering, 3d view and shop drawing (cad & hard copy) including approval from client, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. complete in all respect. All floors & roof. (Mode of measurement will be the single side surface area of modular partition.) complete in all respect. All floors & roof. (Mode of measurement will be the single side surface area of modular partition.)

Synth PF for Sound proof: Extra Providing & fixing 50mm thick Polyurethane foam of 48kg/m3 density to be inserted into the pre - fabricated slot covered Polyurethane foam by making the cloths treated with Naptha @ 0.07 Ltr.per Sq.m. of cloths for acoustic purpose laid over false/ Wall ceiling in marketing cloth packet of approved brand complete as per instruction of ELC.complete in all respect. All floors & roof.

Supplying fixing of premium quality rectangle center table with 6.00 mm thick toughened Colour Tinted glass (IS-2835) with high quality teak wood framing with PU Polish / Stainless steel 304 grade framing. Approx. Size shall be - 1200mm x 550mm x 425 mm (H) (min). All materials used should be of relevant ISI specification. Approved by Engineer-in-Charge.The rate shall include all design, any support (if required) for Engineering, 3d view and shop drawing(cad & hard copy) including approval from client, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers, nut bolts, washer, Buffer plates, fastener, anchors, SS channel, laminated glass etc. complete in all respect. All floors & roof. The products should be tested as per BIFMA standards for at least ten years. The product should have ISO-9001:2015, ISO-14001:2015, ISO-18001:2015, OHSAS 18001:2007 certifications. Energy management system as per ISO-50001-2011, in accordance with the TÜV NORD CERT auditing and -certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and Should have Green Guard, FIRA Certification for few of its products. The above modular Workstation should be as per specification and sample approved by client.All floors & roof.

a) Supplying, fixing of best & premium quality sofa with armrest-LH & Armrest-RH for Under structure: Seat & Body under structure is made of combination of water proof plywood & pinewood members. Plywood is 12± 1mmthk. (moisture resistance & termite proof as per IS:303) & pine wood are cross section (22x64, x22x 40, x22x 100 & 34 x 64)mm are without major knots & defects on the surface. 3.8mm zigzag spring asly. Is mounted on the seat structure with spring mounting plastic clip for support & additional cushioning purpose. Paper coated MS rod is connected with all the spring with clips to give strength to the spring. Non-woven fabric is stapled on the seat structure frame above the spring asly. To avoid the tearing of seat PU foam with the surface contact of metal spring. Complete under structure is made by gluing, nailing & stapling. 3mm MDF & 2mm cardboard is stapled on the structure for PU foam sticking surface or for upholstery stapling reference. Back Top Cushion & Armrest under structure is made of combination is 12± 1mm, 6± 1mm plywood & pine (moisture resistance & termite proof as per IS:303) wood of 22x40 mm & combination 12± 1mm, 6± 1mm plywood, 3mm MDF & pine wood 22x40 for small corner with gluing & stapling. Two number of cushion belts are provide in the back rest plywood for enhanced comfort. Powder coated MS hook of 1.2mm thk. Are mounted on the back side of cushion for mounting the cushion with the body structure

b) Foam: Seat is made of PU foam with density 28Kg/cum. With an additional top layer of super soft PU foam with density 32Kg/cum. Recron sheet of 200GSM is wrapped & glued above this seat top foam. Seat front bottom vertical surface is glued with the PU foam with density 28kg/cum. Side vertical surface, body front taper vertical, back vertical surface & top horizontal surface is glued with PU foam with density 28kg/cum. Back Top Cushion is made of two layers of super soft PU foam with density 32Kg/cum. One additional layer of memory foam of density 70kg/cum given on the super soft foam layers in the backrest cushion for enhanced comfort. Recron sheet of 200GSM or leatherette option is wrapped & glued above this foam. Armrest is made of super soft PU foam with density 32Kg/cum. . Recron sheet of 200GSM or leatherette option is wrapped & glued above this foam

c) Upholstery: Seat, Armrest & Back Top Cushion Top upholstery is made in the dual tone colour with polyester pattern fabric & leatherette option. Leg: Back top Cushion are fitted with the seat & body structure with the M6 Butterfly nut & washer on top surface & MS hook on taper front body structure.(1no Cushion for1 seater sofa) Leg: Plastic PP moulded legs are used & fitted at the bottom surface with the chipped screws. Before fixing legs no- woven fabric is stapled on the bottom surface to cover the structure. The products should be tested as per BIFMA standards for at least ten years. The product should have ISO-9001:2015, ISO-14001:2015, ISO-18001:2015, OHSAS 18001:2007 certifications. Energy management system as per ISO-50001-2011, in accordance with the TÜV NORD CERT auditing and -certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and Should have Green Guard, FIRA Certification for few of its products. . The rate shall include all design, Engineering, 3d view and shop drawing(cad & hard copy) including approval from client, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary. services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. complete in all respect. All floors & roof.

d) 3 Seater Sofa Size- Total width/ Length 3 seater 2010mm x Total Depth 900mmx Total Height 800mmx Seat depth 570mmx Seat Height 465mmx Seat- Back Angle 1050 x leg Height 23mm.

e) 2 Seater Sofa Size- Total width/ Length 2 seater 1340mmx Total Depth 900mmx Total Height 800mmx Seat depth 570mmx Seat Height 465mmx Seat- Back Angle 1050 x leg Height 23mm.

supply fixing and installation window vertical blind best & premium quality prewith mechnical system in any sizes as per Direction of Engineer in charge. The products should be tested as per BIFMA standards for at least ten years. The product should have ISO-9001:2015, ISO-14001:2015, ISO-18001:2015, OHSAS 18001:2007 certifications. Energy management system as per ISO-50001-2011, in accordance with the TÜV NORD CERT auditing and -certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and Should have Green Guard, FIRA Certification for few of its products. . The rate shall include all design, Engineering, 3d view and shop drawing(cad & hard copy) including approval from client, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary. services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. complete in all respect. All floors & roof.

supply fixing and installation window horizontal blind premium quality prewith mechnical system in any sizes as per Direction of Engineer in charge. The rate shall include all design, Engineering, 3d view and shop drawing(cad & hard copy) including approval from client, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary. services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. complete in all respect. All floors & roof.

HALF HEIGHT STORAGE : Supplying, fitting, fixing and installation of Half Height Storage size 450mm (D) x 1200mm (H) made of Top & bottom (25mm), Two Side & Front (Door) 18mm thk.& back 18mm thick Pre-Laminated MDF made MDF (One side decorative lamination other side balancing lamination as per requirement IS: 14587-1998 . Provide 25mm thk. Pre-Laminated or Post laminate MDF made MDF Multiple number adjustable shelf mounting holes provided on side panel for easy interchanging or fixed of shelf height as required. Uniformly distributed load carrying capacity for Each shelf is 40 to 50kg. Provide screw type adjustable leveller with plastic base provide vertical adjustment for floor unevenness and levelling of units and also provide door hinge(Stainless steel) locking arrangement, decorative aluminium/stainless-steel door handle. The Skirting units are provided with 150mm high skirting made of 25mm thk. Pre-Laminated MDF. The rate shall include all design, Engineering, 3d view and shop drawing(cad & hard copy) including approval from client, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. complete in all respect. All floors & roof.

LOW HEIGHT STORAGE : Supplying, fitting, fixing and installation of Low Height Storage size 450mm (D) x 750mm (H) made of Top & bottom (25mm), Two Side & Front (Door) 18mm thk.& back 18mm thick Pre-Laminated MDF (One side decorative lamination other side balancing lamination as per requirement IS: 14587-1998 . Provide 25mm thk. Pre-Laminated MDF Multiple number adjustable shelf mounting holes provided on side panel for easy interchanging or fixed of shelf height as required. Uniformly distributed load carrying capacity for Each shelf is 40 to 50kg. Provide screw type adjustable leveller with plastic base provide vertical adjustment for floor unevenness and levelling of units and also provide door hinge(Stainless steel) locking arrangement, decorative aluminium/stainless-steel door handle. The Skirting units are provided with 150mm high skirting made of 25mm thk. Pre-Laminated MDF. The rate shall include all design, Engineering, 3d view and shop drawing(cad & hard copy) including approval from client, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. complete in all respect. All floors & roof.

OVERHEAD STORAGE :- Supplying, fitting, fixing and installation Pre-Laminate overhead Storage size 450mm (D) x 450mm (H) made of Top, Two Side, back, Intermediate(if required) & Front (Door) 18mm thk. Pre-Laminated MDF (Both or side decorative laminate as per requirement, as per IS: 14587-1998 . Uniformly distributed load carrying capacity for Each shelf is 40 to 50kg. provide door hinge(Stainless steel) locking arrangement, decorative aluminium/stainless-steel door handle. The products should be tested as per BIFMA standards. The above storage should be as per specification and sample approved by client. The rate shall include all design, Engineering, 3d view and shop drawing(cad & hard copy) including approval from client, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. complete in all respect. All floors & roof.

Supplying providing & installing High Back Executive Premium quality (larger size seat) Chair with multi point locking systems (with weight release), pneumatic Seat depth & Back Tilt adjustment, Armrest (with 4-D adjustable), adjustable Lumber support & head/neck rest adjustable. The cushioned seat is made of injection moulded plastic outer & inner. Plastic inner is upholstered with leatherette and moulded High resilience (HR) polyurethane foam of density 45±2 kg/cum & hardness load 16± 2kgf as per IS: 7888 for 25% compression.. The cushioned Back is made of PU foam with in situ moulded MS E.R.W round tube of size 1.9 ±0.03cm x 0.16 ± 0.0128cm. It upholstered with leatherette. The armrest top is moulded from polyurethane (PU) and mounted on to a 4 D adjustable type tubular armrest support made of ∅ 3.81Cm x0.2 cm thk. MS E.R.W. tube having chrome plate finish The armrest height 4 D adjustable up to 6.5 ± 0.5cm in 5 steps. The adjustable tilting mechanism is designed with the following features: i) 360 degree revolving type. ii) Front- pivot for tilt with feet resting on ground and condition adjustable lumber support ensuring more comport. iii) Tilt tension adjustment can be operate in seating position. Iv) 5- position tilt limiter giving option of variable tilt angle to the chair. iv) seat/ back tilting ratio 1:2 v) The mechanism housing is made up of HPDC aluminium (aluminium alloy 63400-WP or IS: 733 & IS IS: 733 & 1285:2002) 8-10 stages anti rust treatment and shall be powder coated with Epoxy polyester in Glossy or matt finish to a thickness of 60 to 70 microns. Seat depthC51:C52 adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0cm minimum. Back frame support is connected to the Up/Dn mechanism housed in plastic T spine. It can be adjusted in the range of 7cm for the comfortable back support to suit individual need. The pneumatic height adjustment has an adjustment stroke of 10.0cm. The pedestal & castor base is high pressure Die cast powder coated (with Epoxy polyester in Glossy or matt finish to a thickness of 60 to 70 microns or chrome plate finish ) aluminium & fitted with 5nos. twin wheel castors. The pedestal is 65cm (minimum). Pitch centre dia (75cm with castors). 5 nos twin wheel castors are injection moulded in plastic having 6.0cm wheel diameter and assembled to pedestal. The visitor tubular frame is cantilever type & made of ∅ 2.54 cm x 0.2cm thk S.S. tube. The back connected to frame through chrome plated high pressure die cast connector piece. The lumber support consist of polypropylene pad with moulded polyurethane foam & covered with polyester fabric. The Height of lumber pad can be adjusted through two projecting knobs provide on the rear side of pad. The neck rest assembly consist of propylene pad with moulded polyurethane foam & covered with leatherette fabric. Neckrest assembly has adjustment of 4.2 cm & rotation adjustment of overall 760. The products should be tested as per BIFMA standards for at least ten years. The products should be tested as per BIFMA standards for at least ten years. The product should have ISO-9001:2015, ISO-14001:2015, ISO-18001:2015, OHSAS 18001:2007 certifications. Energy management system as per ISO-50001-2011, in accordance with the TÜV NORD CERT auditing and -certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and Should have Green Guard, FIRA Certification for few of its products. . The above chair should be as per specification and sample approved by client. The rate shall include all design, Engineering, 3d view and shop drawing(cad & hard copy) including approval from client, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. complete in all respect. All floors & roof.

Supplying providing & installing medium Back Executive Premium quality (larger size seat) Chair with multi point locking systems (with weight release), pneumatic Seat depth & Back Tilt adjustment, Armrest (with 4-D adjustable), adjustable Lumber support adjustable. The cushioned seat is made of injection moulded plastic outer & inner. Plastic inner is upholstered with leatherette and moulded High resilience (HR) polyurethane foam of density 45±2 kg/cum & hardness load 16± 2kgf as per IS: 7888 for 25% compression.. The cushioned Back is made of PU foam with in situ moulded MS E.R.W round tube of size 1.9 ±0.03cm x 0.16 ± 0.0128cm. It upholstered with leatherette. The armrest top is moulded from polyurethane (PU) and mounted on to a 4 D adjustable type tubular armrest support made of ∅ 3.81Cm x0.2 cm thk. MS E.R.W. tube having chrome plate finish The armrest height 4 D adjustable up to 6.5 ± 0.5cm in 5 steps. The adjustable tilting mechanism is designed with the following features: i) 360 degree revolving type. ii) Front- pivot for tilt with feet resting on ground and condition adjustable lumber support ensuring more comport. iii) Tilt tension adjustment can be operate in seating position. Iv) 5- position tilt limiter giving option of variable tilt angle to the chair. iv) seat/ back tilting ratio 1:2 v) The mechanism housing is made up of HPDC aluminium (aluminium alloy 63400-WP or IS: 733 & IS IS: 733 & 1285:2002) 8-10 stages anti rust treatment and shall be powder coated with Epoxy polyester in Glossy or matt finish to a thickness of 60 to 70 microns. Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0cm minimum. Back frame support is connected to the Up/Dn mechanism housed in plastic T spine. It can be adjusted in the range of 7cm for the comfortable back support to suit individual need. The pneumatic height adjustment has an adjustment stroke of 10.0cm. The pedestal & castor base is high pressure Die cast powder coated (with Epoxy polyester in Glossy or matt finish to a thickness of 60 to 70 microns or chrome plate finish ) aluminium & fitted with 5nos. twin wheel castors. The pedestal is 65cm (minimum). Pitch centre dia (75cm with castors). 5 nos twin wheel castors are injection moulded in plastic having 6.0cm wheel diameter and assembled to pedestal. The visitor tubular frame is cantilever type & made of ∅ 2.54 cm x 0.2cm thk S.S. tube. The back connected to frame through chrome plated high pressure die cast connector piece. The lumber support consist of polypropylene pad with moulded polyurethane foam & covered with polyester fabric. The Height of lumber pad can be adjusted through two projecting knobs provide on the rear side of pad. The products should be tested as per BIFMA standards for at least ten years. The products should be tested as per BIFMA standards for at least ten years. The product should have ISO-9001:2015, ISO-14001:2015, ISO-18001:2015, OHSAS 18001:2007 certifications. Energy management system as per ISO-50001-2011, in accordance with the TÜV NORD CERT auditing and -certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and Should have Green Guard, FIRA Certification for few of its products. The rate shall include all design, Engineering, 3d view and shop drawing(cad & hard copy) including approval from client, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. complete in all respect. All floors & roof.

Supplying providing & installing visitor Chair (Size: W60.9cm x depth 64.2cm.x Height 98.2cm Seat Height 44.8cm. The dimension are variation within ± 1.cm are normal) with multi point locking systems (with weight release), pneumatic Seat depth & Back Tilt adjustment, Armrest (with 2-D adjustable). The cushioned seat is made of injection moulded plastic outer & inner. Plastic inner is upholstered with Fabric and moulded High resilience (HR) polyurethane foam of density 45±2 kg/cum & hardness load 16± 2kgf as per IS: 7888 for 25% compression.. The cushioned Back is made of PU foam with in situ moulded MS E.R.W round tube of size 1.9 ±0.03cm x 0.16 ± 0.0128cm. It upholstered with fabric. The armrest top is moulded from polyurethane (PU) and mounted on to a 2 D adjustable type tubular armrest support made of ∅ 3.81Cm x0.2 cm thk. MS E.R.W. tube having chrome plate finish The armrest height 2 D adjustable up to 6.5 ± 0.5cm in 5 steps. The adjustable tilting mechanism is designed with the following features: i) 360 Degree revolving type. ii) Front- pivot for tilt with feet resting on ground. iii) Tilt tension adjustment can be operate in seating position. Iv) 5- position tilt limiter giving option of variable tilt angle to the chair. iv) seat/ back tilting ratio 1:2 v) The mechanism housing is made up of HPDC aluminium (aluminium alloy 63400-WP or IS: 733 & IS IS: 733 & 1285:2002) 8-10 stages anti rust treatment and shall be powder coated with Epoxy polyester in Glossy or matt finish to a thickness of 60 to 70 microns. Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0cm minimum. Back frame support is connected to the Up/Dn mechanism housed in plastic T spine. It can be adjusted in the range of 7cm for the comfortable back support to suit individual need. The pneumatic height adjustment has an adjustment stroke of 10.0cm. The pedestal & castor base is high pressure Die cast powder coated (with Epoxy polyester in Glossy or matt finish to a thickness of 60 to 70 microns or chrome plate finish) aluminium & fitted with 5nos. twin wheel castors. The pedestal is 65cm (minimum). Pitch centre dia (75cm with castors). 5 nos twin wheel castors are injection moulded in plastic having 6.0cm wheel diameter and assembled to pedestal. The visitor tubular frame is cantilever type & made of ∅ 2.54 cm x 0.2cm thk S.S. tube. The products should be tested as per BIFMA standards for at least ten years. The products should be tested as per BIFMA standards for at least ten years. The product should have ISO-9001:2015, ISO-14001:2015, ISO-18001:2015, OHSAS 18001:2007 certifications. Energy management system as per ISO-50001-2011, in accordance with the TÜV NORD CERT auditing and -certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and Should have Green Guard, FIRA Certification for few of its products. complete in all respect. All floors & roof.

Supply & Installation of premium quality Pushback Auditorium with desklet chair with seat slider and auto tip up auditorium chair. The seat frame assembly shall be ERW Tube / IS :3074-2005 GRADE 1: 19 mm dia Round Pipe 1.2mm Thickness . The Seat profile shall be developed to help the users to get necessary comfort in popliteal region and ease of use in forward push for the seat sliding feature. Seat size shall be: 405 mm. (W) x 490 mm (D) x 125 mm (T)(Front) & 80 mm(T)(Rear). The backrest assembly shall be made of ERW Tube / IS :3074-2005 GRADE 1: 16 mm dia Round Pipe 1.63 mm Thickness & Extra Reinforcement 16 dia round pipe 1.2 mm. The back foam shall be designed with contoured lumbar support for extra comfort at upright and tilted conditions. The back shall be: 470 mm. (W) x 823 mm (H) x 110 mm (T)(Front) & 60mm (T)(Rear). The Automotive grade HR polyurethane foam for Seat and Back shall be moulded with Density = 55 +/- 5kgs/cu.m. as per JIS K 6401 with compression max 13%. The back & seat covers are made of injection moulded thermoform PPCP as per IS: 10915-1984 with 457 mm(W)x 755 mm(H)x 2.3mm(T) for back and 435 mm(W)x 552 mm(D)x 2.3mm(T) for seat. The armrest shall be made up of wood with waterfall edge design. Available with retractable wooden desklet. For Push Back mechanism – Coil Spring / Spring Steel IS : 4454 1981 GRADE 2. The fluimatic slider travels upto 60mm with metal ball and roller cage which results in PUSH BACK OF 140 + 10mm . Should have flexibility to restrict movement of the pushback and slider as per availability of aisle space. The mechanism houses the seat & back and shall has a special feature of upright resistance lock to avoid activation of sliding feature unless enough force shall be applied by user when tilting shall be required. For Auto Tip-up – Torsion Spring / Spring Steel IS : 4454 1981 GRADE 2 (Part I). The chair shall rests on the ground on two Side wing frame with water proof plywood with upholstery. Each Leg is a rectangular tube of cross section 50mm X25mm x1.63mm Thickness as per IS: 4923-1985 standards. The side panel frame is made of HRPO sheet metal as per IS: 1079 -1994 standards along with fabric upholstered water proof plywood. It shall be grouted to the floor using 2 nos. anchors for each panel through the base plate. All steel components shall be zinc passivated and powder coated (DFT 40-60 microns). The heavy duty 100 % polyester dyed yarn with 3mm + 0.5mm foam backing fabric is available in shades as per shade card. FR grade material confirms to IS 15061. The auditorium chair shall be designed to get mounted/grouted on floors with concrete (min 100 mm) or wooden flooring (min 50 mm) with specific grouting bolts. Provision for lights on sides for seats along the aisles using PP housing with 12mm watt lamp. Aluminium cut-outs available for row & seat numbering. Overall Dimensions shall be Seat Height - 450 mm, Height - 1040 +/- 10 mm, in armrest c/c - 533 mm, Width & Depth as measured from base - Width-660 mm and Folded Depth-660 mm, Normal depth-760mm, Extended depth- 920 mm. Dimensions tolerance / variations shall be within +/- 10 mm. . The products should be tested as per BIFMA standards for at least ten years. The products should be tested as per BIFMA standards for at least ten years. The product should have ISO-9001:2015, ISO-14001:2015, ISO-18001:2015, OHSAS 18001:2007 certifications. Energy management system as per ISO-50001-2011, in accordance with the TÜV NORD CERT auditing and -certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and Should have Green Guard, FIRA Certification for few of its products.. The rate shall include all design, Engineering, 3d view and shop drawing(cad & hard copy) including approval from client, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. complete in all respect. All floors & roof.

Acoustic Doors: Providing and fixed 64mm thick Acoustic Door compromising of 6mm thick BWR ply fixed on the either side of 2nd class seasoned teak wood framework with 38mm long screws. The teakwood framework shall comprise of 65mmX40mm main runners all around and 03 Nos. equispaced 50mm X 25mm horizontals per door leaf and 100mm X40mm for lock rail. One sikn of 4mm BWP ply to be fixed inside the framework through 3mm thick sheet gasket rubber layer & 45mmX20mm sponge neoprene gasket to be fixed to the bottom edge of the door leaf as per direction of EIC. The product should have ISO-9001:2015, ISO-14001:2015, ISO-18001:2015, OHSAS 18001:2007 certifications. Energy management system as per ISO-50001-2011, in accordance with the TÜV NORD CERT auditing and -certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and Should have Green Guard, FIRA Certification for few of its products.. The rate shall include all design, Engineering, 3d view and shop drawing(cad & hard copy) including approval from client, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. complete in all respect. All floors & roof.

Supplying Fitting & Fixing Inside of Structural Glazing with GOLD DGU : 13.52mm clear toughened laminated glass (i.e.; 6mm clear toughened + 1.52mm PVB + 6mm clear toughened) : Frame less fixing systems with top & bottom Patch fittings. The product should have ISO-9001:2015, ISO-14001:2015, ISO-18001:2015, OHSAS 18001:2007 certifications. Energy management system as per ISO-50001-2011, in accordance with the TÜV NORD CERT auditing and -certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and Should have Green Guard, FIRA Certification for few of its products.. The rate shall include all design, Engineering, 3d view and shop drawing(cad & hard copy) including approval from client, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. complete in all respect. All floors & roof.

Wall Panelling Auditorium : Providing and Fixing Channelled Woodworks perforated panels of minimum width 128mm, thickness of 15mm and maximum length 2440 mm or as required by the Architect/ approving engineer, made of a high density fibre board (HDF) with minimum 830 Kg/Cum density substrate with a laminated facing / wood veneer as per the approved shade/ species & finish and a melamine balancing layer on the reverse side. The boards shall have a special perforation pattern where the visible surface has a “Helmholtz” fluted perforation of 2mm width and 14mm of visible panel each. The panels shall provide a minimum sag resistance of RH 90 and a fire reaction of Class of 1 as per Part 7 of BS 476. The edges of the panels shall be “tongue-and-grooved” to receive special clips for installation. The back of the perforated panel shall have sound absorbing non-woven acoustical fleece having NRC of 0.55. The panels shall be mounted on special aluminium splines using clips and approved by the Architect/ Engineer-in-Charge. (Including the cost of supporting aluminium frame work.) The rate shall include all design, any support (if required) above false ceiling for fixing the partition, Engineering, 3d view and shop drawing(cad & hard copy) including approval from client, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. complete in all respect. All floors & roof.

Providing & fixing in position Phenol bonded Bamboowood wall cladding at all height with planks of sizes 10mm thick, 1800mm length (minimum) and 130 mm wide (minimum), in approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council (BMTPC), with necesasary profiled edges fixed with 40mm SS screws 5 nos in each tile to frame work made of second class teak wood of size 20x15 mm in centre of each tile and bottom and top of work height, 40x15mm placed at ends of each tile. The cladding shall be laid over backlayment of 1.00 mm thick expanded polyethylene foam of density 40kg/cum in two layers, first layer on wall surface before fixing wooden frame and second layer on frame under cladding. The bamboowood planks shall have minimum density of 1000 Kg/cum & minimum Hardness 1000 Kgf. with Eco friendly UV coating, all complete as per direction of the Engineer in-charge. The rate shall include all design, any support (if required) above false ceiling for fixing the partition, Engineering, 3d view and shop drawing(cad & hard copy) including approval from client, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. complete in all respect. All floors & roof.

STAGE FLOOR Providing & fixing 1200 x 75 x 25mm thick seasoned teak wood plank flooring with rabit lapping joints on two layer of 12 mm. think BWR plywood fixed with concealed screw or headless GI nails. Doubel layer of BWR ply shall be fixed with wooden screws of appropriate size to sal wood frame work comprising of 125mm x 125mm. members placed @ 600mm. c/c in both direction. The sal wood frame work shall be fixed to the existing RCC slab with M.S. clamps 25 X 4mm. thick wood planks after filling wood filler and sand papering up to smooth finish in natural colour also including making necessary provision for fixing junction box in floors, all complete with Franch gata polish as per drawings and direction of EIC. (Stage Height Maximum 700mm). The rate shall include all design, any support (if required) above false ceiling for fixing the partition, Engineering, 3d view and shop drawing(cad & hard copy) including approval from client, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. complete in all respect. All floors & roof.

Supplying fitting & fixing Wood work in posts, post plates, rafters, battens, truss members, purlins etc. fitted and fixed complete (including the cost of bolts, two coat primer & synthetic enamel paint, nails, screws etc.). seasoned Sal : Siliguri. complete in all respect. (Note: The sal wood frame work shall be fixed to the existing RCC slab with M.S. clamps 25 X 4mm. thick wood planks after filling wood filler and sand papering up to smooth finish in natural colour also including making necessary provision for fixing junction box in floors, all complete with Franch gata polish as per drawings and direction of EIC. (Stage Height Maximum 700mm).) complete in all respect. All floors & roof.

M.S. structural works with hollow sections (square or rectangular shape) conforming to IS: 806-1968 & IS:1161-1998) connected to one another with bracket, gusset, cleat as per design, drawing & direction of Engineer-in-Charge complete including cutting to requisite shape & size, fabrication including metal arc welding conforming to IS: 816-1969 & IS: 9595 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of all M.S. Hollow section, all consumables such as electrodes, gas and hire charges of all tools and plants and labour reqired for execution and all incidental chages (such as electricity, labour insurance) etc. complete. For other Structural works like galleries & others etc. (Note: The MS Hollow section frame work shall be fixed to the existing RCC slab & Wooden Plank with & including making necessary provision for fixing junction box in floors, all complete with Franch gata polish as per drawings and direction of EIC. (Stage Height Maximum 700mm).) complete in all respect. All floors & roof.

Supplying fitting & fixing Rough dressed seasoned timber planks fitted and fixed with nut bolts excluding framework complete : (including the cost of bolts, paints, nails, screws etc.). Sal Local. 25mm thick planks. complete in all respect. All floors & roof.

Supplying, fitting and fixing boiling water proof ply conforming to IS: 710-1977 bonded with phenol formaldehyde synthetic resin conforming to IS: 848-1974 of approved make and brand fitted and fixed as per design as per approval and direction of Engineer-in-Charge. 12mm thk. complete in all respect. All floors & roof.

Supplying, fitting and fixing boiling water proof ply conforming to IS: 710-1977 bonded with phenol formaldehyde synthetic resin conforming to IS: 848-1974 of approved make and brand fitted and fixed as per design as per approval and direction of Engineer-in-Charge. 16mm thk. complete in all respect. All floors & roof.

Supplying, fitting and fixing boiling water proof ply conforming to IS: 710-1977 bonded with phenol formaldehyde synthetic resin conforming to IS: 848-1974 of approved make and brand fitted and fixed as per design as per approval and direction of Engineer-in-Charge. 19mm thk. complete in all respect. All floors & roof.

Polyurethane Polishing to woodwork with required colour as approved by Engineer-in-Charge with preparing surface including scaffolding and hire charges of compressor machine including cost of filler and hardener material such as P. U. Sealing, P. U. Top coat (Matt/Glossy), Thinner, Spirit etc. and inclusive of all operation, material and labour complete as per direction of Engineer-in- Charge.. complete in all respect. All floors & roof.

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved any wood finish, texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-incharge. With 20 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.7). complete in all respect. The rate shall include all design, any support (if required) above false ceiling for fixing the partition, Engineering, 3d view and shop drawing(cad & hard copy) including approval from client, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. complete in all respect. All floors & roof.

Supplying & fixing carpets of about 12mm thick over foam base (ECO CRI CERTIFIED, ISI MARKED, MACHINE TUFTED) as per IS:5884 of best quality, 100% fire retardant consists of 80% wool, 20% nylon, about 1250 GSM thickness including labour charges, necessary accessories etc. complete as per drawing and directions of Engineer-in-Charge. - in auditorium. complete in all respect. The rate shall include all design, any support (if required) above false ceiling for fixing the partition, Engineering, 3d view and shop drawing(cad & hard copy) including approval from client, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. complete in all respect. All floors & roof.

Providing and fixing in wall lining medium density fibre board IS: 14587:1998 marked, Pre-laminated one side decorative lamination and other side balancing lamination, with necessary fixing arrangement and screws etc. complete. 12 mm thick. complete in all respect. All floors & roof.

Providing and fixing in wall lining medium density fibre board IS: 14587:1998 marked, Pre-laminated one side decorative lamination and other side balancing lamination, with necessary fixing arrangement and screws etc. complete. 18 mm thick. complete in all respect. All floors & roof.

Providing and fixing in wall lining medium density fibre board IS: 14587:1998 marked, Pre-laminated one side decorative lamination and other side balancing lamination, with necessary fixing arrangement and screws etc. complete. 25 mm thick. complete in all respect. All floors & roof.

R, B, ENTERPRISE

Creative Construction And Co

ASHIRBAD INTCON PVT. LTD.

VIBGYOR