REPAIR TO JOINERY, FLOOR, PLASTER, ROOF TREATMENT, ROOF SHEETING, PLUMBING, SANITARY FITTING AND ALLIED B/R WORKS TO MD AND OTM ACCN OF NHO AND CWE (HILLS) DEHRADUN UNDER AGE B/R-III OF GE CLEMENT TOWN

Amount

Demolition of cement concrete (Un-reinforced) in ground floors and pavings n.exc 15cm thick (above or below GL) complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engr-in-Charge.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engr-in-Charge.

Demolition of brick work or stone masonry built in cement mortar including all quoins, arches, jambs etc complete all as specified and directed by Engr-in-Charge.

Demolition of stone slabs and tiles of any description or thickness laid bedded and pointed in any mortar as in floor, aprons,dado etc as specified and directed.

Dismantling wall & ceiling boards (fibre, insulation etc ) or insulation boards, slabs, blankets any thick ness including cover fillets complete all as specified and directed by Engr-in-Charge..

Dismantling timber scantling 40 Sqcm and over in section in any position complete all as specified and directed by Engr-in-Charge.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed by Engr-in-Charge.

Dismantling of Asbestos cement (corrugated, semi corrugated etc.) sheets as in roof coverings complete all as specified and directed by Engr-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise described complete all as specified and directed.

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engr-in-Charge.

Taking down cement plaster of any description on brick work or stone masonry walls including rackingout joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engr-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) of size n.exc 1.50 Sqm complete all as specified and directed by Engr-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) of size exc 1.5 Sqm and n.exc 4 Sqm complete all as specified and directed by Engr-in-Charge.

Taking down shutter of any description exc. 1 sqm but not exc. 2 sqm each complete all as specified and directed by Engr-in-Charge.

Taking down shutters exc 1 Sqm and n.exc 2 Sqm of any description and refixing in same opening/position include cutting for size and fitting including making good of distrub area complete all as specified and directed by Engr-in-Charge.

Taking up or down 15mm dia steel tubing and connections including cleaning for re-fixing or removal from site complete all as specified and directed by Engr-in-Charge.

Taking up or down 20mm dia steel tubing and connections including cleaning for re-fixing or removal from site complete all as specified and directed by Engr-in-Charge.

Disconnecting existing water storage tanks of capacity exc 250 ltr but n.exc 500 ltr, setting aside (or lowering if required) for repairs, cleaning and removing all scales and dirt, etc and refixing in same position complete all as specified and directed by Engr-in-Charge.

Disconnecting existing water storage tanks of capacity exc 500 ltr but n.exc 1000 ltr, setting aside (or lowering if required) for repairs, cleaning and removing all scales and dirt, etc and refixing in same position complete all as specified and directed by Engr-in-Charge.

M&L for Second class hardwood timber scantling wrought framed and fixed as girders, joists, purlins, rafters in any position complete all as specified and directed.

M&L brick work with sub class "B" old size bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed by Engr-in-Charge.

M&L for half brick work with subclass ‘B’ bricks, straight or curved on plan to any radius built in CM 1:4 complete all as specified and directed by Engr-in-Charge.

S&F Pre-painted galvalume aluminum zinc coated GI based corrugated steel sheet 0.50mm thick of any colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge.

S&F Pre-painted galvalume aluminum zinc coated GI based plain steel sheet 0.50mm thick of any colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, ridge etc fixed with self tapping screwscomplete all as specified and directed by Engr-in-Charge.

S&F 0.56mm thick Galvanised corrugated mild steel sheeting with two corrugation side lap fixed with L or J type hooks and washer in roofs with grade of zinc coating 275 complete all as specified and directed by Engr-in-Charge.

All as per item No.26 above but except sheeting (any thickness)

S&F 0.56mm thick Plain Galvanised Mild steel sheeting in ridge, valley gutter with grade of zinc coating 275 complete all as specified and directed by Engr-in-Charge.

S&F Rolled Mild steel work of Fe-290 (Gde E-165) as in framed work, trussed, purlins, crane gantries, rails & fastenings and heavy bracket framing (Beam, tee, angle, channel, Hollow section or flat sections) including distance pieces, cleats etc complete all as specified and directed by Engr-in-Charge.

S&F mild steel framed work as in grills, gratings etc with ends of bars shouldered and riveted or forged into spikes, framed guard bars, barred iron doors etc, conforming to Fe-290, Gde-E-165 complete all as specified and directed by Engr-in-Charge.

M&L for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed by Engr-in-Charge.

S&F Welded steel wire fabric weight n.exc 4 kg/sqm fixed to wood or steel members complete all as specified and directed by Engr-in-Charge.

M&L for 25mm thick PCC (1:2:4) type B-0 (using 12.50mm graded stone aggregate) as in sub base of floor complete all as specified and directed by Engr-in-Charge.

M&L 50mm thick PCC (1:3:6) type C-2 (Using 40mm graded stone aggregate) as in plinth protection /hardstanding , laid in panels, finished the top surfaces even and fair without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L 75mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in sub base of floor complete all as specified and directed by Engr-in-Charge.

M&L RCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in slabs, shelves supported on walls, beams and columns in floor or roof including balconies, canopies, deck slabs or in Chajja/facia projection and the like complete all as specified and directed by Engr-in-Charge.

M&L mild steel TMT bars 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-Charge.

M&L for use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick for fair finished surfaces (Horizontal or sloping) complete all as specified and directed by Engr-in-Charge.

M&L Vitrified coloured tiles 8-10mm thick any Shade/Double charged (square/rectangular) area of each tiles exc 0.18 Sqm but not exc 0.42 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:6 laying floor finishes, complete all as specified and directed by Engr-in-Charge.

M&L Vitrified coloured tiles 8-10mm thick Dark Shade/Double charged (square/rectangular) area of each tiles exc 0.18 Sqm but not exc 0.42 Sqm as in vertical surface such as dado/ skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 to recieve tiles complete all as specified and directed by Engr-in-Charge.

M&L for Non skid Endura coloured tiles 8-10mm thick (square/rectangular) grade-4, area of each tile not exc 0.16 Sqm over and including 15mm thick screed bed in Cement mortar (1:6) in flooring, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed by Engr-in-Charge.

M&L for Non skid Endura coloured tiles 8-10mm thick (square/rectangular) grade-4, area of each tile not exc 0.16 Sqm as in vertical surface such as dado/ skirting etc over and including 10mm thick screed bed in Cement mortar (1:4) in flooring, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed by Engr-in-Charge.

M&L for joint free Non-skid ceramic coloured tiles 7-8mm thick (square/rectangular), area of each tile not exc 0.11 Sqm, over and including 15mm thick screed bed in CM (1:6) in flooring, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed by Engr-in-Charge.

M&L for Glazed ceramic coloured joint free tiles 450x300X7mm in vertical surfaces over and including 10mm thick rendering in Cement mortar (1:4), set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed by Engr-in-Charge.

M&L Vitrified coloured tiles 8-10mm thick light shade (Square/Rectangular) area of each tiles n.exc 0.36 sqm, over and including 15mm thick screed bed in Cement mortar (1:6) in flooring, set and jointed in neat cement slurry and pointed in cloured cement to match complete all as specified and directed directed by Engr-in-Charge

M&L Vitrified coloured tiles 8-10mm thick light shade (Square/Rectangular) area of each tiles n.exc 0.36 sqm, as in skirting/dado, over and including 10mm thick screed bed in Cement mortar (1:4) in flooring, set and jointed in neat cement slurry and pointed in cloured cement to match complete all as specified and directed directed by Engr-in-Charge.

M&L Vitrified coloured tiles 8-10mm thick any shade/Double charged (Square/Rectangular) area of each tiles exc 0.42 sqm but not exc 1.00 sqm over and including 15mm thick screed bed in Cement mortar (1:6) in flooring, set and jointed in neat cement slurry and pointed in cloured cement to match complete all as specified and directed directed by Engr-in-Charge.

M&L Vitrified coloured tiles 8-10mm thick any shade/Double charged (Square/Rectangular) area of each tiles exc 0.42 sqm but not exc 1.00 sqm, as in skirting/dado, over and including 10mm thick screed bed in Cement mortar (1:4) in flooring, set and jointed in neat cement slurry and pointed in cloured cement to match complete all as specified and directed directed by Engr-in-Charge.

M&L for Wall Cladding tile 7-8mm thick area of each tile exc 0.10 sqm but n.exc 0.20 Sqm of any colour and pattern set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick rendering on wall in CM 1:4 and surface finished even & fair Complete all as specified and as directed by Engr-in-charge.

M&L for Machine cut pre polished Kota stone slab 18-20mm thick as in floor/ treads of steps (single piece) laid over and including 15mm thick screed in CM 1:6, set & jointed with grey cement slurry and pointed in white cement mixed with pigment to match the shade of the slab including cutting, rubbing complete all as specified and directed by Engr-in-Charge.

M&L for Machine cut pre polished Kota stone slab 18-20 mm thick (single piece) as in risers to steps, skiting/dado, pillars, window cills and the like, laid over and including 10mm thick rendering in cement mortar 1:4, set & jointed with grey cement slurry and pointed in white cement mixed with pigment to match the shade of the slab including cutting, rubbing and polishing complete all as specified and directed by Engr-in-Charge.

M&L for 18-20mm thick granite (of any type) work (table rubbed and polished) stone slab as in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust to match with marble shade over and including cement screed bed 15mm thick in CM (1:6) complete all as specified and directed by Engr-in-Charge.

M&L Dura stone tiles of size 300x300x8mm thick as in floor over and including 15mm thick screed bed in Cement mortar (1:6), set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and as directed.

M&L for grinding of existing terrazo or kota stone flooring by carborundum stone of 320 to 400 grit size. After grinding the surface shall be washed clean and grouted with neat cement grout of cream like consistency using the same coloured cement as in the original mix. After grinding the surface shall again be washed clean and rubbed hard with felt and slightly moistened oxalic acid powder, at the rate of 5 gm of oxalic acid powder for one sq m of floor surface. After completion of grinding work the wax-polish shall be sparingly applied with soft linen on the clean and dry surface. Then the polishing machine fitted with bobs shall be run over it. Clean saw-dust shall then be spread over the floor and polishing machine again applied, mopping up surplus wax and leaving glossy surface. Care shall be taken that the floor is not let slippery.

M&L for rubber moulded coloured cement concrete chequered tiles polished of size 30cm x 30cm x 25mm thick jointed in neat cement slurry and pointed in white or coloured cement and pigment to match the surface of tile as in floor over 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engr-in-Charge.

M&L for coloured Machine pressed precast polished concrete interlocking paver block as in road berm, path and hardstanding any shape and size confirming to IS 15658-2006 of 80mm thickness, M-35 grade with pigments over and including 50mm thick sand cushioning complete all as specified and directed by Engr-in-Charge.

M&L for coloured Machine pressed precast polished concrete interlocking paver block as in road berm, path and hardstanding any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 grade with pigments over and including 25mm thick sand cushioning complete all as specified and directed by Engr-in-Charge.

S&F 30mm thick factory made flush shutter solid core construction with block board core and ply wood face panels, commercial type both sides complete all as specified and directed by Engr-in-Charge.

S&F in repair powder coated aluminium glazed side hung double door shutters with anodised aluminium frame of section 100x44x1.5mm and shutter having style, top rail, lock rail and bottom rail of 84x44x1.5mm including 5.5mm thick tinted blind sheet glass ordinary quality with all necessary suitable push & pull plate/handle, screw, jointing cleats, rubber packing, aluminium snap beading and 1 No 200mm long Al tower bolt, 100 mm long 3 No Al butt hinges B-21 type, and one No mortice brass lock 100mm size 4 leaver (vertical type) complete all as specified and directed by Engr-in-Charge.

S&F Factory made 100% Solid WPC Brown door Frame (75mm x 50mm Single Rebate) made from 100% LEAD FREE (single extruded process) material with density 780 kg/Cum & Manufactured by an ISO: 9001-2015 certified company, all as per specification drawing as directed by the Engineer-in-Charge. The door frame should be Waterproof, Termite Proof, Fire Retardent and having excellent screw holding capacity complete all as specified and directed by Engineer-in-Charge.

S&F Factory made 100% Solid WPC Brown door Frame (100mm x 63mm Single Rebate) made from 100% LEAD FREE (single extruded process) material with density 780 kg/Cum & Manufactured by an ISO: 9001-2015 certified company, all as per specification drawing as directed by the Engineer-in-Charge. The door frame should be Waterproof, Termite Proof, Fire Retardent and having excellent screw holding capacity complete all as specified and directed by Engineer-in-Charge.

S&F Factory made 100% Solid WPC Brown door Frame (125mm x 63mm Double Rebate) made from 100% LEAD FREE (single extruded process) material with density 780 kg/Cum & Manufactured by an ISO: 9001-2015 certified company, all as per specification drawing as directed by the Engineer-in-Charge. The door frame should be Waterproof, Termite Proof, Fire Retardent and having excellent screw holding capacity complete all as specified and directed by Engineer-in-Charge.

S&F 24mm thick Moulded WPC Brown Factory made 100% Solid door (Conforming as Per IS:4020) made from 100% LEAD FREE single extruded with 2, 4 or 6 raised panel design on the front side with 10mm deep mould on single side with Wood Grain Texture and back side plain with density not less than 600 kg/cum. Manufactured by an ISO: 9001-2015 certified company. The door should be Waterproof, Termite Proof, Fire Retardent and having screw holding capacity complete all as specified and directed by Engineer-in-Charge.

S&F 30mm thick Moulded WPC Brown Factory made 100% Solid door (Conforming as Per IS:4020) made from 100% LEAD FREE single extruded with 2, 4 or 6 raised panel design on the front side with 10mm deep mould on single side with Wood Grain Texture and back side plain with density not less than 600 kg/cum. Manufactured by an ISO: 9001-2015 certified company. The door should be Waterproof, Termite Proof, Fire Retardent and having screw holding capacity complete all as specified and directed by Engineer-in-Charge.

M&L 30mm thick Factory made solid WPC (Wood Plastic composit) molded gauged door shutter with wire mesh in any number of division with brown wood grain texture, including S.S wire mesh shall be fixed with 15x15 square tube in side rails with screwing 8x28 heat metal zink coated screws can be remove or fix again after changing of wire mesh when needed. The density of the shall be as per manufacture instructuon complete all as specified and direced.

S&F 30mm thick Factory made Wiremesh SOLID PVC Door Shutter Consisting of frame made out of M.S.tube of 19 guage thickness and size of 19mm x 19mm for stiles and 15mm x 15mm for top, lock & bottom rail. M.S Frame shall have a coat of metal primer of approved make and manufacturer 19mm x 19mm M.S square tubes shall be covered with 5mm thick PVC heat moulded (100% LEAD FREE) plain sheet 'C' channel 75x30x60 out of 10mm shall be heat at 90 deg. towards inner site of both site of both face of the door forming stiles for top, bottom, lock rails shall be fitting of 10mm inner site all rails (T,B lock) shall be covered with 100mm wide PVC sheet S.S wire mesh shall be fixed with 15x15 square tube in side rails with screwing 8x28 heat metal zinc coated screws can be remove or fix again after changing of wire mesh when needed complete all as specified and directed by Engineer-in-Charge.

Repairing of existing Aluminium doors incl replacement of hydraulic floor door closer(where required), adjusting the members etc. complete and making doors functional complete all as specified and directed by Engr-in-Charge.

Repairing of existing glass door shutters of any size including replacement of hydraulic floor door closer(where required), repairing top pivot, repairing and fixing wall members etc. complete and making doors functional complete all as specified and directed by Engr-in-Charge.

S&F three track Pre coated Steel Sliding Window System fabricated from roll formed sections made of Galvanized Steel Colour Coated/ Powder Coated (Base Steel as per IS 513 “D” quality, galvanized as per IS 277 with Zinc of 120 grams/ Sq. Mtr.) with total coated thickness of 0.58 mm or Powder Coated with pure Polyester Powder up to 50-60 microns thick. Windows Section for three track external frame should be of 44 x 107mm , Section for window glass shutter should be of 36 x 50 mm, if required Section for shutter horizontal mullion should be 22mm x 60mm, The windows should be paneled with 5mm thick Plain Float glass Gaskets are to be made with Ethyl Propylene Diamine Manomer (EPDM). Corner brackets for internal and external frame made of Polypropylene. Touch lock to be provided for window shuttes Sections are to be cut to length, joined and assembled by means of corner brackets. The above Frame should be fixed to brick/ concrete masonry by using Nylon self-expanding caps and driving MS electroplated 80mm long screws into the caps through frames.Windows shall be provided with fixed Stainless steel 32gauge wire mesh/gauze of 304grade with 144 holes per square inch for mosquito proofing with the help of nut, bolt and flat iron of 20x3mm size on top and Grill made of 12mm MS Square bars welded to 25x4mm angle iron . Distance between bars should not be more than 100mm centre to centre. Total Grill and wire mess unit shall be powder coated.Assembling and installation of windows and ventilators shall be all as per details shown/mentioned on drawings and as per manufacturer‟s instructions complete all as specified and directed by Engr-in-Charge.

S&F Pre coated Steel fixed type Window/ Ventilator fabricated from roll formed sections made of Galvanized Steel Colour Coated/ Powder Coated (Base Steel as per IS 513 “D” quality, galvanized as per IS 277 with Zinc of 120 grams/ Sq. Mtr.) with total coated thickness of 0.58 mm or Powder Coated with pure Polyester Powder up to 50-60 microns thick. The windows should be paneled with 5mm thick frosted glass Gaskets are to be made with Ethyl Propylene Diamine Manomer (EPDM). Corner brackets for internal and external frame made of Polypropylene. The above Frame should be fixed to brick/ concrete masonry by using Nylon self-expanding caps and driving MS electroplated 80mm long screws into the caps through frames. Windows shall be provided with Grill made of 12mm MS Square bars welded to 25x4mm angle iron . Distance between bars should not be more than 100mm centre to centre. Total Grill shall be powder coated.Assembling and installation of windows and ventilators shall be all as per details shown/mentioned on drawings and as per manufacturer‟s instructions complete all as specified and directed by Engr-in-Charge.

S&F Window/ventilator prepainted section of frame 72x55mm fixed to wall or concrete surface with rawl plugs made of galvanised steel powder coated and section of shutter 47x20mm, mulion section 72x50mm (Base steel as per IS 513 "D" quality galvanized as per IS 277 with zinc of 120 gms/Sqm) glazed and wire gauge shutter prepared to receive wiremesh to the shutter (Double shutter) with total coated thickness of 0.6mm including grills/guard bars made made of 12mm square bars powder coated fixed to window frame with screws at 150mm c/c both ways, 4 mm thick sheet glass, 0.36mm stainless steel wire cloth ieht 1.4mm aperture and necessary fittings and all builders hardware such as handles, tower bolts & stays etc complete all as specified and directed by Engr-in-Charge.

S&F Aluminium powder coated three track sliding windows (with three sliding shutters, (One with and incl stainless steel wire mess and two with and incl 4mm thick sheet glass panes) aluminium sections not less than 1.1kg per meter for bottom track and top track and side track 0.98 kg per metre, bottom shutter frame 0.55 kg per metre, top shutter frame 0.47 kg per metre, shutter sides, 0.47 kg per metre and interlock sides 0.45 kg per metre including suitable nylon beading channel gasket, nylon rollers Maruthi lock with handles etc complete all as specified and directed. Windows shall be provided with guard bars using 25mm flat iron and 10mm square bars of design including painting of guards bars, complete all as specified and directed by Engr-in-Charge.

S&F Aluminium powder coated fixed glazing with aluminium frame of weight not less than 1.2 kg/m with and incl 8mm thick glass (plain/ tinted) of size as directed by the Engineer-In-Charge including suitable nylon beading channel gasket, etc complete all as specified and directed by Engr-in-Charge.

S&F in repair 18mm thick WPC board one side prelaminated and other side plain white colour as in cup boad shutters and frames, kitchen cabinet front shutter, partion, shelf & drawer, fixed with screws, solvent cement/ adhesive complete all as specified and directed by the Engineer-in-Charge.

S&F in repair 18mm thick , prelaminated medium density fibre (MDF) , interior grade, prelaminated one side with decorative choice lamination and other side balancing white with lamination fixed with screw to timber/ steel frame work as in CB shutter, shelves etc with PVC liping on all exposed edges on same texture and shade. Stainless steel cleat of suitable size will be use to fix the shelves of CB and cabinets.

S&F in repair 18mm thick with min density 600 Kg / cum LEAD FREE PVC Celuka ply of single side rigid laminate of approved color and other side plain white colour fixed with ss screws and solvent cement/ adhesive to make kitchen cabinet shutters complete as per manufacturer’s instructions complete all as specified and directed.

S&F 0.90mm thick Decorative laminate type 1, of surface finish, colour and pattern as approved , fixed with approved adhesive as per GE instructions, complete all as specified and as directed.

S&F of 100mm long mild steel butt hinges, medium weight cold rolled complete all as specified and directed by Engr-in-Charge.

S&F 150mm long, Stainless Steel barrel tower bolts complete all as specified and directed by Engr-in-Charge.

S&F Stainless steel bow handle "D" type anodized 150mm long complete all as specified and directed of make prayag and equivelent..

S&F Stainless steel bow handle "D" type anodized 100mm long complete all as specified and directed.

S&F of 250mm long (Length of bolt) Stainless Steel sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, and fixing bolts and sliding bolt complete all as specified and directed by Engr-in-Charge.

S&F 150mm Stainless Steel Hasp and Staple, including bolt to hinge plate and fixed with screws complete all as specified and directed by Engr-in-Charge.

S&F in repair Hydrulic Self Closing hinges 35mm of crank( KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete in all respect and fixed in position complete all as specified and directed by Engr-in-Charge.

S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 100mm long matt finished complete fixed in position all as specified and directed by Engr-in-charge.

S&F Ball catchers 304 grade stainless steel finished suitable for cabinets premium quality complete fixed in position as per manufacturer's instructions all as specified and directed by Engr-in-charge.

S&F in repair door closer aluminium (extruded section) body hydraulically regulated, designation No. 3, universal type, complete all as specified and directed by Engr-in-Charge.

S&F in repair 300mm long MS Helical ordinary rat tail rod pattern door spring including roller and roller plate etc complete of approved quality complete all as specified and directed by Engr-in-Charge.

S&F in repair of 140mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, Overall length of cover plate complete all as specified and directed by Engr-in-Charge.

S&F in repair 4mm thick plain glass of aluminium window by taking down window shutter by any means and replacing rubber packing, jointing clip etc complete all as specified and directed by Engr-in-Charge.

S&F for Glazing with plain sheet glass, ordinary quality, 4mm thick and glazing with oil putty or aluminium or PVC beading in squares not exceeding 0.5 Sq.m in each pane complete in repair all as specified and directed.

S&F for Glazing with plain sheet glass, ordinary quality, 5.5 mm thick and glazing with oil putty or aluminium or PVC beading in squares not exceeding 0.5 Sq.m in each pane complete in repair all as specified and directed.

S&F for Glazing with plain sheet glass, ordinary quality, 5.5 mm thick and glazing with oil putty or aluminium or PVC beading in squares exceeding 0.5 Sq.m in each pane complete in repir all as specified and directed by Engineer-in-charge.

S&F for Stainless steel curtain rod, 25mm dia with fixing brackets and decorative type knobs both side of each rod, incl taking down old curtain rod or pelmet boxes complete all as specified and directed by Engineer in Charge. Note :- Measurement will be taken between end point of knobs.

S&F Dust/Snake guard aluminium strip in doors of size 40x2mm with rubber at strip bottom complete all as specified and directed by Engr-in-Charge.

M&L 15mm thick rendering in cement mortar (1:6) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L 15mm thick rendering cement mortar (1:4) mixed with liquid water proofing compound on fair faces of brick work or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified and directed by Engr-in-Charge. (WPC shall be paid seperately)

M&L for 10mm thick plaster on roof, chajja and roof parapet of CM (1:3) on RCC finished even and smooth without using extra cement etc ncl taking down cement plaster complete all as specified and directed by Engr-in-Charge.

M&L 5mm thick rendering in ceiling of cement mortar (1:3) on fair faces of brick work or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified and directed by Engr-in-Charge.

Supply only liquid water proofing compound complete all as specified and directed by Engr-in-Charge.

M&L for three coats of white wash to newly plastered surfaces of ceiling including preparation of surfaces, complete all as specified and directed by Engr-in-Charge.

M&L for two coats of oil bound distemper over a coat of 2mm thick wall putty to newly plastered surface including preparation of surfaces complete all as specified and directed by Engr-in-Charge.

M&L two coats of cement based paint over a coat of primer to newly plastered surfaces of wall including preparation surfaces complete all as specified and directed by Engr-in-Charge.

M&L two coats of weather proof emulsion paint Apex in newly plastered surface over a coat of primer incl preparing the surface with 2mm thick wall putty complete all as specified and directed by Engr-in-Charge.

M&L for preparation old surfaces of plastered or unplastered old decorated surfaces of walls by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of acrylic distemper on walls including cornices, pilasters etc complete all as specified and directed by Engr-in-Charge.

Ditto all as per item No.105 here in above but on ceiling surfaces complete all as specified and directed by Engr-in-Charge.

M&L for preparation of old decorated surface of internal wall by removing existing treatment with mechanical sander (rpm 1500-2700) along with internal dust extraction system for clean environment certified by reputed paint manufacturers and applying two coats of acrylic distemper using roller over a layer of 2mm thick wall care putty to make the surface smooth all as specified and prescribed by manufacturer of paint and all as directed at site by Engr-in-Charge. Note:- (i) The old surface must be prepared in a manner so that there should not be any impression of dent and it should be made even and smooth all as per manufacture’s instruction before application of distemper. The cost of materials, labour & T&P required for preparation of surface are deemed to be included in the rates quoted. (ii). The work must be got executed through authorised applicator of manufacture after concluding an MoU with manufacture for company back guarantee by the contractor. The authorised applicator of manufacturer shall be got approved from GE before commencement of work. (iii). All the material to be incorporated in the work shall be brought by contractor to MES store yard which will be subsequently issued by department for incorporation in the work to ensure the quantity to be consumed all as per recommendation of manufacture. (iv). After carrying out preparation of surface the same shall be got approved from GE before application of distemper for each building. (v). The colour / shade will be all as approved by GE.

M&L for preparation surface of old wall by washing,rubbing down and stopping of surfacest and applying one coat of cement base paint on walls complete all as specified and directed by Engr-in-Charge.

M&L for preparation surface of old wall by washing,rubbing down and stopping of surfaces incl complete removal of existing treatment and applying two coat of cement base paint on walls complete all as specified and directed by Engr-in-Charge.

M&L for Preparation old decorated surfaces and applying one coat of white wash on ceilings complete all as specified and directed by Engr-in-Charge.

M&L for preparation of old decorated surface of exterior wall by removing existing treatment with mechanical sander (rpm 1500-2700) along with dust extraction system for clean environment certified by reputed paint manufacturers, then washing the surface with Bleaching powder solution for treatment of fungal growth and applying two coats of exterior anti fungal acrylic emulsion paint (wallmista of Berger paint or equitant in Asian paint, Nerolac etc having three years of performance warranty) over a coat of exterior water based primer of same make all as specified and prescribed by manufacture of paint and as directed at site by Engineer-in-Charge. Note:- (i) The old surface must be prepared in a manner so that there should not be any impression of dent and it should be made even all as per manufacture instruction before application of distemper. The cost of materials, labour & T&P required for preparation of surface are demand to be included in the rates quoted. (ii). The work must be got executed through authorised applicator of manufacture after concluding an MoU with manufacture for company back guarantee by the contractor. The authorised applicator of manufacturer shall be got approved from GE before commencement of work. (iii). All the material to be incorporated in the work shall be brought by contractor to MES store yard which will be subsequently issued by department for incorporation in the work to ensure the quantity to be consumed all as per recommendation of manufacture. (iv). After carrying out preparation of surface the same shall be got approved from GE before application of distemper for each building. (v). The colour / shade will be all as approved by GE. (vi) The cost of Scaffolding wherever required are deemed to be included in the rates quoted by the contractor.

M&L preperation of old painted concrete/tile floor surfaces of any description includig scraping, brushing, brooming down and repair surface with Primer and applying two coat of Indigo emulsion fioor paint any tint / shade over a coat of primer complete all as specified and directed by Engr-in-Charge.

M&L for preperation of old painted plastered or concrete surfaces of any description and applying one coat of synthetic enamel paint complete all as specified and directed by Engr-in-Charge.

M&L for preparing new steel and iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint of any tint over one coat of red oxide primer complete all as specified and directed by Engr-in-Charge.

M&L for preparing old steel and iron surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engr-in-Charge.

M&L for preparing old wooden or wood based surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engr-in-Charge.

S&F for GI tubing 15mm bore, medium grade ISI marked with all fittings(such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions, including short lengths etc.) ( heavy grade ISI Marked) , fixed to walls, concealed in wall and ceiling or laid in floor complete complete all as specified and directed.

S&F for GI tubing 20mm bore, medium grade ISI marked with all fittings(such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions, including short lengths etc.) ( heavy grade ISI Marked), fixed to walls, concealed in wall and ceiling or laid in floor complete complete all as specified and directed.

Refixing old steel tubing of 15mm bore and connections in new or old position (walls, ceilings, floors etc.) together with all fittings heavy duty (ISI Marked ) (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.) and fixed complete to walls and ceiling with clips, wall hooks, wooden plugs or laid in floors Complete all as specified and directed

Refixing old steel tubing of 20mm bore and connections in new or old position (walls, ceilings, floors etc.) together with all fittings heavy duty (ISI Marked ) (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.) and fixed complete to walls and ceiling with clips, wall hooks, wooden plugs or laid in floors Complete all as specified and directed

Cutting chases, pinning in, making good to facing where required and pointing in Cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc and cutting chases for concealed water pipe etc and making good, cutting not exc 10cm width or girth complete all as specified and directed by Engr-in-Charge.

S&F in repair 15mm dia gun metal gate valve with iron wheel haeded screwed both ends to iron pipe and fixed complete all as specified and directed by Engr-in-Charge.

S&F in repair 20mm dia gun metal gate valve with iron wheel haeded screwed both ends to iron pipe and fixed complete all as specified and directed by Engr-in-Charge.

S&F in repair 110mm dia PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches/floor or fixed to wall including necessary clamps complete all as specified and directed by Engr-in-Charge.

S&F in repair 75mm dia PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches/floor or fixed to wall including necessary clamps complete all as specified and directed by Engr-in-Charge.

S&F in repair 75mm dia PVC (SWR) Multi floor trap with grating including jointing with solvent cement including fixing waste pipe etc complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC (SWR) junction single, (Single T) equal or unequal 110mm bore with access door complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC (SWR) junction single, (Single T) equal or unequal 75mm bore with access door complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC (SWR) bend any radius 110mm bore complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC (SWR) bend any radius 75mm bore complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC (SWR) bend any radius 110mm bore with access door complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC (SWR) bend any radius 75mm bore with access door complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC vent cowls 75mm complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC connection 15mm bore dia 450mm long with 2 Nos PTMT nuts with washer complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC waste pipe 32/40 mm dia complete all as specified and directed by Engr-in-Charge.

S&F in repair CP Grating doom 125mm dia with waste hole of steel fixed on floor/nahani trap with cement mortar, complete all as specified and directed.

S&F in repair 20mm dia CP tubular towel rail D type 600mm long complete all as specified and directed by Engr-in-Charge.

S&F in repair for SS towel ring of standard quality complete all as specified and directed.

S&F in repair SS Soap dish fixed to wall with screw complete all as specified and directed.

S&F in repair brass CP bib tap 15mm bore fancy type screwed for iron pipe complete with wall flange complete all as specified and directed by Engr-in-Charge.

All as per item No.140 here-in-before but long body type complete all as specified and directed by Engr-in-Charge.

S&F in repair 15mm bore Stop valve fancy type, chromium plated with long shunk and cup (concealed type) high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified and directed by Engr-in-Charge.

S&F in repair 15mm dia brass chromium plated pillar tap long body with fly nut capstan head screwed for 15mm bore dia of pipe complete all as specified and directed by Engr-in-Charge.

S&F in repair chromium plated brass shower roses with or without swivel joints 125mm size including shower arm complete all as specified and directed by Engr-in-Charge.

S&F in repair of Sink made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm and bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engr-in-Charge.

Supply & fix wall mixer with over head shower chromium plated for mixing hot and cold water screwed for iron pipe suitable for 15 mm bore pipes complete all as specified and directed .

S&F in repair 15mm dia brass CP Sink mixer with swinging spout (wall mounted model) with connecting legs and wall flanges screwed down for iron pipe and fixed complete all as specified and directed .Note- Chromium plated fitting shall be brought in store yard first as approved by GE and will be issued subsequently for fixing at site .

S&F in repair 15mm dia chromium plated central hole wash hand basin mixer without PWS with 450mm BRAIDED HOUSE hose screwed down high pressure screwed for iron pipe completed all as specified and directed.

S&F in repair CP health faucet with 1m flexible tube and wall hook complete all as specified and directed by Engr-in-Charge.

S&F in repair CP angular stop cock 15mm dia single way and fixed complete all as specified and directed by Engr-in-Charge.

S&F in repair CP toilet paper holder fixed to wall with CP brass screws complete all as specified and directed by Engr-in-Charge.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engr-in-Charge.

S&F in repair Corner self 300mm radius of 10mm thick toughened glass with CP railing with bracket S & Fixed with brass screw complete all as specified and directed by Engr-in-Charge.

S&F in repair Vitreous china wash hand basin including brackets, white size 550 x 400mm incl cutting cutting for and pinning in ends of brackets. Including Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed complete all as specified and directed by Engr-in-Charge.

S&F in repair Vitreous china squatting pan ‘Orissa pattern’ size 580x440mm white with integral foot rest including connection to trap, and flushing pipe, anti-syphonage pipe, etc and including lime concrete bedding complete all as specified and directed by Engr-in-Charge.

S&F in repair 10 Litre capacity PVC low level flushing cistern with ball valve and handle/push button 32mm dia PVC flush pipe including taking down unserviceable cistern complete all as specified and directed by Engr-in-Charge.

S&F in repair Vitreous china wash down water closed pan (Pedestal pattern) white, including connection to drain (or out going pipe) and to flush pipe, antisypthonic (excluding flushing cistern and flush pipe) complete all as specified and directed by Engr-in-Charge.

S&F in repair Vitreous china white wash down couple closet composite type including PVC soft seat cover white complete all as specified and directed by Engr-in-Charge. Make : Jaquar, Cera or Parryware.

S&F in repair seat cover suitable for vitreous china couple closet including fixing bolts complete all as specified and directed by Engr-in-Charge.

S&F in repairs Kitchen Plate rack with and including shelves and hanging arrangement for utensil for kitchen, made of stainless steelsheet 0.63mm thick size 24"x24"x10" complete all as specified and directed by Engr-in-Charge.

S&F in repairs PVC water storage tank double layer cylindrical, vertical with closed top with threaded cover hoisted and fixed in position tank capacity 500 Ltr with and including ball valve high pressure of PTMT with epoxy coated Aluminum rod and high density plastic ball screwed for 20mm bore of iron pipe and making connection for inlet and outlet including dismantle of old water tank and removing from site complete all as specified and directed by Engr-in-Charge.

S&F in repairs PVC water storage tank double layer white colour cylindrical, vertical with closed top with threaded cover hoisted and fixed in position tank capacity 1000 Ltr with and including ball valve high pressure of PTMT with epoxy coated Aluminum rod and high density plastic ball screwed for 25mm bore of iron pipe and making connection for inlet and outlet including dismantle of old water tank and removing from site complete all as specified and directed by Engr-in-Charge.

S&F in repair 20mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 210 gram) complete all as specified and directed by Engr-in-Charge.

S&F 18 guage powder coated Aluminuium framed work of size 75 x 45mm with and including snap beads rubber gasket, fixing arrangement in partition fixed in wall & floor upto minimum 2.10m high in two panels complete all as specified and directed. Note :- (a) 5.5mm thick tinted or clear glass in top panel. (b) 12mm thick prelaminated interior grade both side laminated particle board in bottom panel.

S&F Window blind is made up of several long horizontal or vertical slats of various types of hard material, including wood, plastic or metal which are held together by cords that run through the blind slats plain or printed type, of design and shade as approved by the Engineer-In-Charge complete with all connected fittings and fixtures incl taking down old drapery rods/ pelmets complete all as specified and directed by Engr-in-Charge.

M&L for concrete in Sunken floor and vertical faces of walls to ease up about corners with cement concrete 1:2:4 type B0 (using 12.50mm stone aggregate) mixed with SBR Latex liquid polymer (mixed as per manufacture instructions & will be paid under relivnt item of Sch A) including using form work (straight or curved) as required complete as per directions by Engr-in-Charge.

M&L for Providing precast cement concrete louvres and jallies, type B0, 1:2:4 (using 12.5 mm graded agg) 45mm thick (measured solid), including all mouldings but excluding frame and set in CM 1:4 complete all as Specified and directed by Engr-in-Charge.

M&L for providing cement concrete 1:2:4 type B-1 for fixing edge of interlocking tiles and rounded or chamfered edges, coping complete all as Specified and directed by Engr-in-Charge.

S&F tiled False Ceiling of Everest Fibre Cement Tex Ceiling or Pre Primered tile (High Pressure Steam Cured) o 4mm thickness (as per IS: 14862) of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections consisting of main "T'' runner with suitabley spaced joints to get required length and 15x32 mm made from 0.30mm thick sheet, spaced at 1200 mm c/c and cross "T" of size 15x32mm made of 0.30mm sheet, 1200mm long spaced between main "T" at 600mm c/c to form a grid of 1200x600 mm and secondary cross "T" of length 600mm and size 15x32mm made of 0.30mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 15x20x0.40mm and laying false ceiling tiles in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanized Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15mm of all T-sections shall be pre-painted with polyester paint and black painted groove at center of size 4mm depth and 4.5mm width, all complete at all heights as per direction of Engineer-in-Charge.

S&F False Ceiling with Semi perforated 10mm thick Square edged GRG False Ceiling tiles at all heights with GRG (Glass Fiber Reinforced Gypsum) false ceiling tiles of size 595 x 595mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Nomocombustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120grams per Sqm incliuding both sides) comprising of main-T runners of size 15x32mm of length 3000mm, cross-T of size 15x32mm of length 1200mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per Sqm) i.e. 50mm lon, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod up to 1000mm length and L-shape level adjuster os size 85x25x2mm. Galvanized iron perimeter wall angle of size 24x24x0.40mm of length 3000mm to be fixed on periphery wall/ partition with the help of plastic rawl plugs at 450mm centre to centre and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing complete all as specified and directed by Engr-in-Charge.

S&F in repair 5.5-6mm thick PVC heavy grade hollow profile designer sheet strips & channel feathered at edges of approved quality and design PVC Wall/Ceiling Panelling including matching PVC angles at all window corners, jambs & cills complete all as specified and directed by Engr-in-Charge.

Removal of existing roof treatment i.e. APP Membrane, brick tiling including concrete padding and benching and open up RCC roof slab including picking, sweeping cleaning with wire brush and washing down with water to remove dust, dirt to get surface free of laitance, scales, oil or any other loose material without damaging existing serviceable structure complete to receive new roof treatment including rubbish off the premises upto a distance exc 250 mtr but n.exc 500 mtr complete all as specified and directed by Engr-in-Charge. (Note : The work is required to be carried out at non-accessible roof for double storey. The contractor shall make arrangement of scoffolding , safety & security of workers and arrangement for approach to roof. The rates quoted shall deemed to be included for these iems.)

M&L for 25mm thick PCC (1:2:4) Type B-0 (using 12.5mm graded stone aggregate) pedding mixed with liquid water proofing compound (as per manufacture direction and paid separately) over and incl one coat of cement slurry admixed with acrylic bonding compound SBR Latex liquid polymer as to be used for bonding of new concrete/mortar to old surface as per manufacturer direction and finishing the surface even and smooth (without usin extra cement) as in roof padding/Sunken floor, kerb/bencing alongwith parapet including rounded, chamfered on edges complete all as specified and directed by Engr-in-Charge. (Note : Proportion of mix and method of mixing of approved concrete admixture should be applied as per manufacturer's printed instructions) (Note : The work is required to be carried out at non-accessible roof for double storey. The contractor shall make arrangement of scoffolding , safety & security of workers and arrangement for approach to roof. The rates quoted shall deemed to be included for these items.)

M&L for rendering 10mm thick screed bedding in CM (1:3) mixed with acrylic bonding compound SBR Latex liquid polymer finished the surface even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge. (Note : Prpportion of mix and method of mixing of approved liquid water proofer admixture should be applied as per manufacturer's printed instructions) (Note : The work is required to be carried out at non-accessible roof for double storey. The contractor shall make arrangement of scoffolding , safety & security of workers and arrangement for approach to roof. The rates quoted shall deemed to be included for these items.)

M&L of water proofing treatment to non-accessible roof slab with APP based modified polymeric membrane as per manufacturer's instructions with following course of description below :- (i) Applying a priming one coat of bituminious primer evenly @ 0.30 Kg/Sqm till the surface is properly impregnated. (ii) Providing APP based 5 layer polymeric membrane minimum weighting 3.60 Kg/Sqm and minmum 3mm thick reinforced with polyester non-woven fabric matt (weight not less than 150 gms/Sqm) centre core laid on primed surface by forced applications as per the manufacturer's instructions with side over lap of 75mm and end overlap of 100mm. All overlap joints shall br sealed thoroughly by thermo fusing both the membrane layer (torching overlap by propane or butane gas torch) and sealing it with the help of hot trowel. The overlap joints shall be made as a monolithic layer. (iii) Apply two coat of bituminous aluminium pain @ 0.20 Kg/Sqm over APP Membrance. (Note: the work in respect of water proofing treatment shall be carried out only by authorized/approved applicator of the manufacturer/firms of app membrane. The contractor shall submitted 10 year company back warranty before claiming payments complete all as specified and directed. (Note : The work is required to be carried out at non-accessible roof for double storey. The contractor shall make arrangement of scoffolding , safety & security of workers and arrangement for approach to roof. The rates quoted shall deemed to be included for these items.)

NOTES :- 1. For the items for which specifications not mentioned any where in the tender, the BIS specifications shall be followed.

ANEJA AND COMPANY (BID ID -3068589)

M/s Pradeep Kumar (BID ID -3076648)

G S CONSTRUCTIONS (BID ID -3077969)