SPECIAL REPAIR/REPLACEMENT OF LT CABLES , PCC POLES, JUNCTION BOXES AND CONNECTED ITEMS AT AIR FORCE STN PHALODI

Amount

Dimantling of existing unserviceable PCC pole of any size and type from its position from the site and taking away from site including necessary excavation and earth work in any type of soil, demolition of concrete, disconnecting of street light fitting ect complete all as specified and directed.

Supply, errecting & fixing in true vertical position Steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts & screws as specified type 410 SP-31 (9.00 metres long) confirming to relevent IS including one coat of primer of red oxide and two coats of aluminium paint and two coats of bituminous paint inside and out side of bottom portion up to 1.8 mtr length complete all as specified and directed.

Material and labour in replacement of FRP junction box of size internal 250 x 200 x 105 and External 295 X 255 X 120 mm having 4 Nos aluminium bus bar of size 20X4 mm fixed on epoxy insulators with MCB SP 6 Amps,fixed on the pole with clamps,nut bolts etc. complete all as specified and directed.

Supply and fixing in repairs for rigid non-metallic PVC conduit of 20 mm dia heavy duty alongwith street light poles for wire from junction box to light fittings including fixing arrangement complete all as specified and directed.

Material and labour for in replacement for circuit /sub main wiring from junction box to street light fitting complete with 1.5 sqmm 3 core PVC insulated and PVC round sheathed multistranded copper conductor flexible industrial cable 1100 V grade drwan through PVC conduit in street light poles complete all as specified and directed.

Supplying, installing, testing and commissioning outdoor type cubical feeder pillar box dust proof both side opening of size 1000x800x400mm made out of MS sheet of 3.0mm thick powder coated machine pressed front opening with rubber gasket/bedding, locking arrangement with sliding bolt including aluminium busbar 400 Amp 4 strips mounted on insulators each strip should be mounted minimum two insulator and nut bolt panel shall be mounted on angle iron frame and legs made from angle iron of suitable size duly spray painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer grouted in PCC (1:2:4) type B1 using 20 mm graded stone aggregate foundation incoming/outgoing cable provision including dismantling old feeder pillar box complete all as specified and directed. .

Disconnecting and Taking out of old LT armored PVC cables of any size/core/any voltage grade from trenches for replacement complete all as specified and directed.

Supply, laying, testing and commissioning cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, elecric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 25 sqmm 3.5 core complete all as specified and directed. Note:- (i) Cable may be laid in trenches, under road, across the Nallah, along poles/walls and ducts etc. (ii) Excavation, earthwork, sand cushioning, cable cover, pipe for cable protection to be measured and paid separately.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth or n exc 10 Sqm on plan and n exc 1.5 m in depth & getting out for laying underground cable in soft/loose soil complete all as specified and directed.

Removing excavated surplus material to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cms thick in any type of soil complete all as specified and directed.

M&L for dry tibba sand in trenches for cushioning to under ground cable spreading, levelling, hand punning complete all as specified and directed. Note- Punned down thickness will be measured for payment purpose.

Supplying and laying reinforced precast concrete cable cover, Class LV, Type I, flat, size 250mm x 150mm x 40mm laid by dry and abutting each other with gap between adjacent slab not exc 10mm over under gound cable for protection complete all as specified and directed.

Material & labour for Earthing complete with galvanized steel earth plate electrodes 600 mmx600 mm x6 mm thick buried directly in ground earth plate not less than 2.25 m deep below normal ground level with top edge of the plate not less than 1.5 m below normal ground level connected to and including galvanized GI strip 32X6mm by means of bolts, nuts, check nuts and washers of galvanized iron and steel including PCC pit in PCC (1:2:4) type B-1 using 20 mm graded crushed stone aggregate, RCC frame with 40mm thick RCC cover reinforced with 8mm dia deformed bars handle. including excavation and earth work in any type of soil medium grade GI watering pipe 20mm bore with funnel and wire mesh and light grade GI protection pipe 15mm bore main board complete all as shown in electrical plate No 3 connected to main control board all as specified and testing on completion. Note: (i) Excavation earthwork charcoal PCC pit is covered under this item including taking out existing earth plate etc. complete all as specified and directed. (ii) The unit rate includes for protection pipe and GI strip 32 x 6mm from top of earth plate up to 7.5 meter above ground level.

S&F 50 mm bore tube, 'light grade' galvanised, for encasing cables for mechnical protection, laid under plinth/floor/path/culvert or fixed on wall or connected in wall/floor or along poles or as street light pole or as mounting bracket , bent to shape with complete accessories such as bend/sockets/reducer/saddles including necessary threading/drilling works complete all as specified and directed.

Supply and fixing energy efficient LED street light fitting of 60 Watt ,epoxy powder coated pressure die cast aluminium housing to act as heat sink for efficient dissipation of heat and toughened glass with IP 66 degree of protection, system luminous efficency more than 100 lumens / watt individual LED's should have lenses for better throw across and along road, PF>0.9 with voltage range 140 to 270 Volt, fitting should be provided wih inbuilt 10 KV minimum surge protection, short circuit and over voltage protection facility for Driver and fiiting including bracket of suitable size upto 1.5 mtr long & MS Flat clamp of suitable size complete all as specified and directed.

Material & labour for PCC (1:4:8) type D-2 using 40mm graded crushed stone aggregate as in pole foundation complete all as specified and directed.

Material & labour for Providing, cement concrete (1:2:4) type B0 using 12.5mm graded stone aggregate for pole base foundation and coping complete all as specified and directed.

new india engineers

LADDOS BUILDCON

M/S SOLANKI GENERAL SUPPLIERS

Deccan Enterprises

shree shyam enterpises

M/S SHREE BHAIRAV NATH ENTERPRISES