PROVN OF SOLAR SECURITY LIGHTS REPLACEMENT OF BER APPLIANCES AND PROVISION OF 40 HP PUMP FOR PUMP HOUSE NO 2 AT HQ SAC UNDER GE AF TRIVANDRUM

Amount

Supply and fixing all-in-one integrated LED solar streetlight 12 watts consists of solar photovoltaic module, battery, battery management system, control electronics, LED driver, inter-connecting cables and pole mounting piece integrated into the luminarie as a single unit. Solar street-light with IP65 ingress protection having a Maximum system wattage of 12W with minimum 2000 lumen output, 28wp high efficiency polycrystalline solar panel, highly efficient MPPT based charge controller and 12.8 V, 13.60 Ah IP68 Lithium Ferro Phosphate(LiFePO4) battery with proper battery management system.

Supply and fixing all-in-one integrated LED solar streetlight 16 watts consists of solar photovoltaic module, battery, battery management system, control electronics, LED driver, inter-connecting cables and pole mounting piece integrated into the luminarie as a single unit. Solar street-light with IP65 ingress protection having a Maximum system wattage of 16W with minimum 3000 lumen output, 35wp high efficiency polycrystalline solar panel, highly efficient MPPT based charge controller and 12.8 V, 20 Ah IP68 Lithium Ferro Phosphate(LiFePO4) battery with proper battery management system

Supply and fixing all-in-one integrated LED solar streetlight 20 watts consists of solar photovoltaic module, battery, battery management system, control electronics, LED driver, inter-connecting cables and pole mounting piece integrated into the luminarie as a single unit. Solar street-light with IP65 ingress protection having a Maximum system wattage of 20W with minimum 4500 lumen output, 60wp high efficiency polycrystalline solar panel, highly efficient MPPT based charge controller and 12.8 V, 30 Ah IP68 Lithium Ferro Phosphate(LiFePO4) battery with proper battery management system. Note for item Ser No 1 to 3:- (i) Contractor shall provide 05 years warranty of light system and minimum 03 years of battery. (ii) Make: Phillips/ Wipro/ Bajaj. (iii) Excavation and earth work shall be measured and paid separately.

Excavation in trenches not exc 1.5m wide and not exc 1.5m in depth for laying UG cable not exc 1.5m in depth and getting out in hard/dense soil complete all as specified and directed .

Removing excavated material not exc 50m and depositing where as directed at a level not exc 1.5m above the starting point complete all as specified and directed .

M/L for PCC 1:4:8 Type D2 with 40 mm graded aggregate for foundation complete including necessary form work complete all as specified and directed

M/L for PCC 1:3:6 Type C1 with 20 mm graded aggregate for coping of pole, making good the disturbed surfaces etc complete including necessary form work complete all as specified and directed

Taking down ceiling fan 1200mm/1400mm sweep from any height and bringing down to floor, and refixing the new fan in same position. Old retrieved ceiling fan will be deposted to GE AF) Trivandrum MT Store yard.

Taking down exhaust fan 300 mm sweep from any height and bringing down to floor, and refixing the new fan in same position. Old retrieved exhaust fan will be deposted to GE AF) Trivandrum MT Store yard.

Taking down wall mounted 400 mm sweep from any height and bringing down to floor, and refixing the new wall mounted fan in same position. Old retrieved wall mounted fan fan will be deposted to GE AF) Trivandrum MT Store yard.

Supply Ceiling fan complete with accessories 230 V 50 Hz 1200 mm sweep complete with 02 Nos cups, 01 down rod, 01 set of blade including electric connection with copper cable 3 core x 0 .75/1.00 sqmm upto ceiling rose all as specified and directed. Make : Havells Model No ES Neo (White Color) or equivalent in Crompton/Orient

Supply heavy duty exhaust fan complete with accessories 230 V 50 Hz, 300 mm sweep, 1400 RPM including louvers nuts bolts/ fastners, electric connection with copper cable 3 core x 0 .75/1.00 sqmm upto ceiling rose all as specified and directed. Make : Havells Turbo Force SP or equivalent in Crompton/Orient

Supply Wall mounting Fan 400 mm Sweep with oscillating 230 Volts 50 Hz AC complete with all accessories suitable for wall mounting, including electric connection with copper cable 3 core x 0 .75/1.00 sqmm upto ceiling rose all as specified and directed. Make : Havells Model Swing or equivalent in Crompton/Orient

Supply and fixing RKB65/19E- 3 stage, 2900 RPM, side suction, top discharge multistage pump fitted with CI Casing, bronze impeller, SS shaft 80 mm suction x 65 mm delivery discharging 16 LPS at a total head of 125 mtrs coupled with ABB make 30 kw/40 HP, 3000 RPM (Syn), TEFC, IP 55, Class F, IE 2 squirrel cage induction motor in frame 200L, assembled on a common MS base plate of dimension not less than 1435 x 530 mm minimum fabricated out off 100 mm channel or more and coupled by means of flexible jaw coupling size not smaller than 190 suitable for connection of 150/125 mm dia pipe for suction and 100 mm pipe of delivery with fully automatic star delta starter with single phase protection including making foundation as per manufacturer instruction for installation / fixing of the pump set all as specified and directed Make: Kirloskar / KSR / Mather and Platt

Supply and laying and testing of medium grade galvanised iron steel tubing of following sizes, ISI marked, including GI fittings such as flanges, reducing bends, elbows, tees, checknuts, caps, plugs etc complete laid in trenches/floors etc complete all as specified and directed. Make : Jindal/Tata/Prakash

(a) 100 mm dia bore

(b) 150 mm dia bore

S & F in repairs CI sluice valves of 150 mm bore size of bore, flanged, heavy duty, class PN 1.0, as per IS-14856 including brass spindle, with hand wheel, nuts bolts and gaskets complete all as specified and directed.Make Leader/Kirloskar/ Bir

S & F in repairs Non return (Reflux) Valve150 mm dia bore , cast iron, of following size of bore, flanged, with GM working parts as per IS - 5312, with nuts bolts and gaskets complete all as specified and directed. Make Leader/Kirloskar/Normax

S & F in repairs CI foot valve Ball type flanged end of 150 mm dia bore, flanged/as per IS - 4038 with nuts, bolts and gaskets etc complete all as specified and directed. Make Normax,/Kirloskar/ Leader

Supplying and installation of pressure gauge for 150 mm dia pipe with suitable pressure rating

S & F fully automatic Star Delta Starter suitable for induction motors of 40 HP/30 KW, Type of ML 3 3 Phase 415 Volts 50 Hz AC, with single phase protection complete all as specfified and directed. Make: L&T / Seimens/ Schineder

Supply install testing and commissioning Auto Mains Failure Silent type Close coupled Diesel Generating set 62.5 KVA Emission complaint & Noise complaint CPCB-II developing 83 Bhp, water cooled coupled with 62.5 KVA (50 KW) , 3 phase, 415 Volts, 1500 RPM Micro Processor based engine controller with Remote Monitoring facility , Std control Panel with 3 Pole MCCB, 200 A base frame, foundation as per OEM specification, batteries with leads and other accessoriers with type approved KG Canopy as a complete set. Control Panel should be installed outside of the canopy, including first fill of lube oil and Engine safeties- LLOP, HWT suitable for ambient condition at Trivandrum. The capacity of Generator set shall be net after all due derating factors as per relevant IS/BS Standards design. Make: Kirloskar / Cummins / Greaves -cotton

Note :- (i). The quoted rate shall be deemed to be inclusive of first fill of oil and final successful acceptance test and foundation of DG Set as per norms. (ii) The quoted rate shall be deemed to be inclusive of 12 hours test run at site as specified in PS in presence E/M Offr detailed by accepting officer, all testing arrangements/ equipments diesel shall be made available by the contractor for tests . (iii) The complete DG Set shall be procured from authorised OEM of the manufacturer of engine. A certificate in this connection shall be submitted to the GE. (iv) Anything missed out above but technically required for efficient working of DG Set is deemed to be included in quoted rates.

(a) Scope of Supply - Diesel engine shall be 4 Cylinder, water cooled, developing 83 Bhp at 1500 RPM, electric start, compression ignition, designed to run continuously and confirming to the standards ISO 3046 and BS 5514, DIN 6271 , IS 10002:1981. The engine will have the following standard accessories. Radiator with fan and fan guard Flywheel housing and flywheel suitable for single bearing alternator. Inline fuel pump Dry type air cleaner (Replaceable two element air filtration system) Exhaust Silencer (residential / hospital type) with Expansion bellows - 2 Nos. Lube Oil filter (Spin on type) Fuel filter (Spin on type) and water separator Mechanical governor confirming to class A2 with integral fuel system suitable for isochronous operation Lube Oil Cooler Exhaust gas driven turbocharger Charge air cooler (air-to-air type) 12V Electric starting system with starter motor and alternator

(b) Digital Engine Control Panel : ON/OFF START Key Lube Oil pressure indication Water temperature indication Battery charging indication Electronic Hour meter Engine speed Coolant level status Auto start facility - inbuilt Controller for electronic governor Indication and trip facility for low lube oil pressure, high water temperature and over speed Engine inputs suitable for communication with computers for remote monitoring with optional RS485 or RS 232 Fuel gauge indication

(c) ALTERNATOR: 62.5 kVA, 0.8 pf (lag), 50 kW, 415V, 3 phase 4 wire, 50Hz, screen protected drip proof (SPDP) with IP23 protection, class H insulation and temperature rise also limited to class H and single bearing type Alternator confirming toIS:4722/1992, BS: 5000 part 99/ IEC34-1 (d) BASE FRAME Base frame is fabricated in formed sheet metal, primer coated and painted. The base frame is rugged in construction and designed for mounting Kirloskar/KOEL engine and KG brush less alternator close coupled, with cross members mounted on AVM. The base frame is having provision of lifting hook for conveninent lifting to complete set. Make: Kirloskar/ Stamford/ Crompton greaves

(d) Acoustic Enclosure Acoustic enclosure shall be powder coated and fabricated out of 16 SWG CRCA MS sheet. The silent canopy shall be of integral, nut bolt type construction. Critical processes of punching is done on CNC machines to maintain dimensional accuracy of holes within 0.1 mm. Powder coating is done after seven-tank surface preparation process of sheet metal. Canopy panel and doors shall have inside lining of world class higher density acoustic FIRE – RETARDANT foam (confirming to BS 4735/ BIS 7888). Four hinged doors with rubber binding and stainless steel door locks shall be provided to canopy. The hot chamber of the canopy is properly insulated by mineral wool and aluminum foil to prevent excess heat radiation on the engine and safe for operator. The base plate & top is powder coated / painted with OXFORD BLUE / PEPSI BLUE, the canopy is powder coated / painted with IVORY colour. (f) Surface Treatment-Painting The enclosure surface shall be suitably treated for degreasing, degusting and phosphate. The canopies are passed through seven-tank treatment thoroughly. Performance Parameters (g) The average sound level, when measured in green field condition (ISO 3744 or 8528 PT 10) at 1-meter distance from all four sides shall be less than 75 db averages or as per CPCB norms.  The average stabilized hot air temperature rise with in the canopy is maintained with in 10o C over and above ambient temperature.

(f) Fuel Tank :Fuel tank shall be fabricated out of 16SWG CRCA MS sheet and duly painted and fitted with inlet and outlet connections with a capacity of 150 liters to 200 Ltrs (g) Battery with leads: Exide/Prestolite/Amron make dry uncharged - 1 Nos, 12V, 150 AH, batteries with leads and terminals.

(k) AMF Panel : Designing fabrication, supply commissioning & testing of factory made, Micro processor based integral AMF Panel with by pass panel, suitable for 62.5 KVA DG set (with 12V DC control system), indoor type CPRI type, CPRI approved fabricated out of 16 SWG, CRCA sheet, undergone 7 tank process with powder coating, cubicle, compartmentalized, free standing, floor mounted, dust and vermin proof, removable gland plate, provision for cable entry from bottom, door lock with panel key, etc, Panel assembly generally confirm to IS 8623 and built with the following items: - (a) 100 Amps, 4 pole contractor for Alternator. (b) 100 A, 4 pole duty contractor for FB mains (c) Microprocessor based AMF module for DG panel. (d) Emergency stop (e) Multifunction V, A, PF, KW, KWH Meter with CRT 45/5A, 15 VA, Class 1. (f) 160 A Aluminium bus bar. (g) 100 Amps, TP MCCB (2 Nos) + Nil for EB & DG Incomers. (h) Fault indications and CT indicatiors for DG on, Load on, Load on DG, Main on, Load on Mains.

B5BUILDING SOLUTIONS