TOKEN NO. GE/K-28/2024-25 - PROVN OF 01 X TOILET BLOCK AT MTN BDE SIG COY AND PROVN OF WALL PANELLING AND CEILING IN BLDG NO. T-20, T-30 AND T-26 OF BDE AT DRASS UNDER GE KARGIL(2ND CALL)

Amount

M&L for surface dressing n.exc 15 cm deep and getting out in hard/dense soil complete all as specified.

Excavating in trenches n exc 1.5 m in depth for foundation, & n exc 10 Sqm on plan and n exc 1.5 m in depth and getting out in hard / dense soil complete all as specified.

M&L PCC 1:4:8 type D-2 (using 40mm graded stone aggegrate) in foundation, filling and mass concrete.

M&L precast cement concrete type C-1, 1:3:6 using 20mm graded stone aggregates, block masonry with solid blocks, exc 10cm width andsetting cement mortar 1:6 complete, all as specified and directed.

Form work to sides of conrete foundation footings bases of columns, raft and raft beams sides and soffits of foundation and plinth beams and similar work etc. in flat rough finished surfaces of concrete complete all as specified and directed by Engr-in-Charge.

Form work to sides of pillars posts struts piers coloums and stanchions etc., in square, rectangular or polygonal rough surface of concrete complete all as specified and directed by Engr-in-Charge.

Form work to sides and soffits of floor or roof beams, beams haunchings, girders, bressumers, lintel, cantilevers, shelves including supports, ovrhangs etc also splayes between floor and bemas in flat rough surface of concrete complete all as specified and directed by Engr-in-Charge.

Form work to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar work not exc 200mm thick (Horizontal or sloping) in flat rough surface of concrete complete all as specified and directed by Engr-in-Charge.

M&L mild steel TMT bars 10 mm dia and over cut to length bent to shape required inclduing cranking bending spirally for hooping ends and binding with and incl mild steel wire (annelaed) not less than 0.90 mm dia or securing with clips.

All as per Srl item No. 9.00 here-in-before but 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders complete all as specified.

M&L for reinforcement cement concrete (design mix) M-25 (using 20mm graded crushed stone aggregate) in roof beams and gable end etc.complete all as specified and directed by Engr-in-Charge.

M&L for reinforcement cement concrete (design mix) M-25 (using 20mm graded crushed stone aggregate) in foundation , including rafts, footing,foundation beams, plinth beams, bases for coloums etc.complete all as specified and directed by Engr-in-Charge.

M&L for reinforcement cement concrete (design mix) M-25 (using 20mm graded crushed stone aggregate) as in columns, pillars, piers, posts and struts, complete all as specified and directed by Engr-in-Charge.

M&L for reinforcement cement concrete (design mix) M-25 (using 20mm graded crushed stone aggregate) as in beams, cantilevers, bressumers, lintel over 1.5m span complete all as specified and directed by Engr-in-Charge.

M&L for reinforcement cement concrete (design mix) M-25 (using 20mm graded crushed stone aggregate) as slabs supported on walls, beams and colomns in floors, roofs, landings, balconies, canopies, desk slabs and in shelves and the like complete all as specified and directed by Engr-in-Charge.

Returning filling including spreading leveling watering and well ramming in layers not exceeding 25 mm in any type of soil.

Removing excavated material n.exc. 50 m and deposited were directed at a level n.exc.1.5 m above the starting point complete.

Earth filling in floors including spreading, levelling and ramming with watering as required in layers n.exc 25cm thick.

Hard core of broken stones or boulders of gauge in exc 63mm deposited spread and levelled in layers n. exc 15cm thick incl watering and rolled to true surface.

M&L 75mm thick cement concrete (1:4:8) type D2 using 40mm graded aggregate as in sub base to floor as specified.

M&L PCC 1:3:6 type C1 (using 20 mm grade aggregate) 75 mm thick as in plinth protection/paving complete all as specified and as directed.

M&L rendering 15 mm thick in CM 1:6 on fair faces of brick work or concrete surfaces, finishing even and smooth without using extra cement complete all as specified and as directed.

M&L rendering 15 mm thick in CM 1:4 on other fair faces of brick work or concrete surfaces in two layers 10mm & 5mm thick with WPC to be used in outer layer of 5mm thick, finishing even and smooth without using extra cement complete all as specified and as directed (WPC measured and paid seperately).

Supply only liquid waterproofing compound

M&L Fe 290 (Gde E-165) for roof trussed (framed), trussed, purlins, crane gantries, rails and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and as directed.

Supply & fixing Rolled mild steel Gde Fe-290 (Gde E-165) as in Plates (plain or chequered) channels,angle sections, square cut or notched (ordinary & counter sunk) forming holes, with riveted, bolted or welded attachment complete all as specified.

Supply & fixing 20mm dia of neck mild steel rag or lewis bolts, screwed one end, with hexagonal or square nuts and washers, the other end enlarged and jagged or lewised, length of bolt exc 30cm long complete all as specified.

Supply & fixing for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified

Supply & fixing for Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L PCC type B0 1:2:4 (12.5mm graded aggregate) 25mm thick as in floor finished surfaces fair and even to receive tile all as specified and as directed

M&L Non skid Ceramic coloured tiles 7 to 8mm thick area of each tiles exc 0.06 sqm but not exc 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm screed bed in CM 1:6 finished even and smooth for receive tiles complete all as specified.

M&L for Glazed ceramic coloured tiles in vertical surfaces 350mmx450mmx7mm thick etc set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade of tile over 10mm thick rendering in cement mortar 1:4 in backing coat of plaster for skrting/dado complete all as specified.

M&L for 20mm thick granite (of any type) work table rubbed and polished) in steps, pillars, jambs, window cills, cooking plateform/whash basin plateform etc and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite all as specified.

Supply & fixing 2nd class softwood (KAIL) as in Plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

Supply & fixing 35mm thick 2nd class soft wood (KAIL) plain framed panelled shutters (any No of pannels) with panels of timber flat on both sides (Feather edgeed), or of veneered particle board medium density, wood particle board with commercial face veneers, supplied and fitted to chowkats complete all as specified and as directed

Supply & fixing 30 mm thick 2nd class soft wood (KAIL) glazed and skeleton shutter open rebated and prepared to receive glass, gauge etc divided into squares with plain chamfered or rounded, mitred and rebated sash bars any numbers.

Supply & fixing 100 mm butt hinges medim weight cold rolled mild steel fixed with screws or welded all as directed.

Supply & fixing butt hinges medium weight cold rolled mild steel of 75 mm long complete.

Supply & fixing anodised aluminium barrel tower bolt extruded sections 200 mm size complete.

Supply & fixing anodised aluminium barrel tower bolt extruded sections 150 mm size complete.

Supply & fixing 125mm extruded aluminium alloy handles febricated type anodised complete all as specified and as directed.

Supply & fixing 100mm extruded aluminium alloy handles febricated type anodised complete all as specified and as directed.

Supply & fixing 250mm Aluminium alloy, anodised,sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

Supply & fixing 3 mm thick sheet glass, ordinary quality and glazing with oil putty or wooden beading in square n exc 0.5 sqm complete all as specified and as directed.

M&L preparation of new plastered surfces of walls and applying three coat wash complete all as specified and as directed.

M&L for preparationof new plastered surfaces on walls and applying two coats of cement based paint over a coat of primer.

M&L for preparation of wood and wood based material surface of any description description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primercomplete all as specified and as directed.

M&L prepation of new or previously untreated surfaces on steel of any description, over 10cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Supply & fixing high grade stainless steel toilet pan of size 58.5cm x 48.2cm x30cm (excludiig flushing cistern and flush pipe) complete all as specified.

Supply & fixing PVC flushing cistern valveless syphonic action type flushing cistern low level 10 Ltrs white with inlet ball valve float and handle incl bracket.

Supply & fixing vitreous china urinal bowl type complete including provoding and fixing plugs bedding urinal against wall in cement mortar 1:2 securing urinals to plug with and incl 60cm long brass screw pointing around urinal back in cement complete all as specified.

Supply & fixing vitreous china urinal partition white of size 310x700mm complete all as specifed and as directed.

Supply & fixing WHB counter sunk type ovel under/over counter shape in fixed & on stone slab incl necessary cutting etc complete all as spcifed and directed.

Supply & fixing pillar tap 15 mm bore fancy type cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed and fly screwed for iron pipe complete all as specified

Supply & fixing 15mm dia chromium plated fancy type Bib tap with round handle screwed down screwed for iron pipe or brass ferrule complete all as specified and as directed.

Supply & fixing 15mm dia chromium plated fancy type stop valves/angle cock screwed down high pressure, screwed for iron pipe complete all as specified and as directed.

Supply & fixing PVC connection15mm size, with PTMT nuts of length 600mm complete all as specified and as directed.

Supply & fixing 32mm CP waste coupling with waste pipe complete all as specified.

Supply & fixing 32mm CP waste coupling with waste pipe but suitable for urinals complete all as specified.

Supply & fixing CP urinal spreader complete all as specified.

Supply & fixing Towel rail 600 mm long PTMT fixed with and incl chromium plated brass screws and wooden/ plastic cleats (Min Wt 170 gms).

Supply & fixing PVC (SWR) floor trap, plain with grating including jointing with solvent cement diameter of outlet 75mm complete.

Supply & fixing 75mm bore PVC (SWR) bends any radius with access door complete all as specified and as directed

Supply & fixing 75mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified and as directed

Supply & fixing 110mm PVC (SWR) 'P' trap complete all as specified.

Supply & fixing 110mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified and as directed

Supply & fixing 110mm bore PVC (SWR) bends any radius with access door complete all as specified and as directed

Supply & fixing 75mm bore PVC (SWR) vent cowl complete all as specified and as directed

PVC (SWR) pipes 110mm dia single socketed in any length with rubber ring joints, laid in trenches or in floors

PVC (SWR) pipes 75mm dia single socketed in any length with rubber ring joints, laid in trenches or in floors

Supply & fixing for 25 mm outer dia 3-layer PPR polypropylene random copolymer concealed pipes SDR 7.4 (PN16) UV stablized and antimivrobial fusion welded having thermal stability for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to wall, ceiling or in floors all as specified.

Supply & fixing for 20mm outer dia 3-layer PPR polypropylene random copolymer concealed pipes SDR 7.4 (PN16) UV stablized and antimivrobial fusion welded having thermal stability for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to wall, ceiling or in floors all as specified.

Supply & fixing rotational moulded polytheline water storage tank 1000 Ltrs capacity (cylinercial/vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

Supply & fixing Gun metal globe or gate valve with iron wheel head screwed both ends for iron ipe and fixed of 20mm bore diacomplete all as specified and as directed

Supply & fixing CP soap tray fixed to walls with rubber plugs complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-2 for bore of pipe as concrete bed to drain pipes including packing under and haunchng against the sides of pipes after they are laid and tested complete all as specified and directed by Engr-in-Charge.

Supply & fixing 150 mm bore PVC (SWR) pipes single socketed in any length with adhesive joint laid in trenches or in floor complete all as specified and as directed.

M&L for providing plain cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in copings, benching etc. complete all as specified and directed by Engr-in-charge.

Material & labour for precast RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in cover slab for manhole etc with plane faces complete all as specified and directed by Engineer-in-Charge.

Material & labour for TMT bars 6mm to 8 mm dia cut to length bent to shape required including cranking, bending, hooking ends and binding with MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed by the Engineer-in-Charge.

Removing excavated material (soil) exc. 500 m but n.exc. 1.5km and depositing where directed at a level n.exc. 1.5 m above the starting point.

Supply & fixing second clas soft wood fillets square or rectangular in section sectional area exceeding 13 sq cm and n exc 25 sq cm as in scantling secured with nails or brads complete all as specified and directed.

Supply & fixing 12mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails to timber frame work in walls complete all as specified and directed.

Supply & fixing 9mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails to timber frame work in ceiling or sloping portion complete all as specified and directed.

Supply & fixing second class softwood moulding as in cornices, picture rails and the like sectional area exceeding 3 Sqcm and n.exc 6 sqcm fixed with nails complete all as specified and directed.

M&L Joint free Non Skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tiles exc 0.18 and n.exc 0.38 Sqm in floors over 15mm thick screed bed in cement mortar 1:4 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tile all as specified and as directed.

M&L for Point wiring for light/fan/bell with FRLS cable of 1.5sqmm PVC insulated (red/blue/yellow for phase, black for neutral and green for earth) unsheathed multistranded copper conductor 1100 volts grade in and including not less than 2mm thick PVC casing caping with all accessories and 1.5sqmm green in colour PVC insulated multistranded copper conductor FRLS cable for earth continuity connected to common earth dolly incl MS sunken box with 3mm thick pre laminated hylum sheet/PVC box flush/surface type for mounting fittings such as switches,socket,and regulator complete all as specified and directed for one light point or bell/buzzer point controlled by one switch.

All as per Srl item No. 88.00 here in before but with 2.5sqmm cable and 2.5sqmm for earth continuity for multi 5 pin 5 amp socket outlet on independent board.

All as per Srl item No. 88.00 here in before but with 2.5sqmm cable and 2.5sqmm for earth continuity for 16 Amp socket outlet on independent board.

Supply & fixing Switch piano flush type 5 Amps, single pole one way.

Supply & fixing Switch socket combination 2 in 1, and 3 and 2 pin, 5 Amps flush type.

Supply & fixing Switch socket combination 2 in 1, 5 and 15 Amps flush type.

Supply and fixing LED light fitting with high output diffuser 2 feet, 10 watt,220 Volts decorative type with driver,holder and LED lamp having lumen output min 100lm/watt,CCT : min 5700K, PF>0.9 including connecting up with two core flexible copper conductor cable complet all as specified and directed.

Supply and fixing LED 1x18/20 Watt, 220 V, AC decorative box type fitting with driver, holder including LED tube ligh having lumen out put 100lm/wattt,CCT:6500K , PF>0.9, and connecting up with two core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply & fixing in replacement of LED Flood light fitting 70 watt 5000 k green/natural white , IP>66 ,grey powder coated die cast aluminium housing, inbuilt energy efficent surge protected electronic driver, with all connected accessories all as specified and directed .

Supply & fixing Ceiling rose on PVC squre block surface bakelite, two to three terminals.

Supply & fixing Sheet metal enclosure MCB DB's double door, 240V, 8 way with 200 Amp rated bus bar including blanking plates where required, complete all as specified and directed.

Supply and fixing miniature circuit breaker (MCB) SPN 32 Amp, 240 V 10 KA C curve complete with connection testing and commissioning.

Supply and fixing miniature circuit breaker (MCB) SP 5 to 32 Amp 240 V 10 KA C curve complete with connection testing and commissioning.

Supply and fix in replacement exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm

M&L for Earthing complete with galvanised steel earth plate electrode of size 60cm×60cm× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to and including GI iron wire of size 4 mm dia by means of GI bolts, nuts, check nuts and washers, protected by 15mm bore GI light grade ISI marked pipe upto and including test points. Earth plate shall be surrounded by alternate layer 15cm thick of charcoal or coke and common salt all around bottom and top , 20mm bore GI medium grade ISI marked pipe for watering and including funnel,wire mesh,PCC chamber pit made with PCC(1:3:6) type C-1(using 20mm graded stone aggregate) including necessary form work, excavation and earth work in any type of soil, returning filling and disposal of surplus soil to a distance not exceeding 50M, CI pit cover duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified & shown in electrical plate No.3 of SSR 2009 (Part-I) and all as directed. Note:- (i) PCC chamber shall be constructed at least 1.5 meter away from the earth electrode and pipe for watering shall be provide in slanting manner. (ii) Protection pipe and earthing strip upto test point from top of the earth plate and further upto the body of electrical equipment shall be included in the unit rate of this item. (iii) Earth testing arrangement should be done by contractor as per direction of Engr-in-Charge.

Supply & fixing 1100 volts grade heavy duty 10 sqmm 2 core flat cable PVC insulated aluminium stranded conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended complete all as directed.

Note : Deduction for amount of Rs 0.00 as listed in Schedule A Part - II ( Schedule of Credit) shall be made while awarding of contract.

Ashfaq Construction Company (BID ID -3147542)

M/S BHAT ENGINEERS (BID ID -3139616)

SAMEER CONSTRUCTIONS (BID ID -3140956)

KASHMIR FAIR DEAL SERVICES (BID ID -3147571)

GAGAN ASSOCIATES (BID ID -3147609)