SPECIAL REPAIRS TO BUILDING NO. P-32, P-37, T-217 and T-220 AT COMMAND SPORTS COMPLEX UNDER GE NB VISAKHAPATNAM

Amount

SCHEDULE 'A' PART-I [B/R Works]: Dismantling of Floor, Hearth or Wall Tiling of any description including Cement Mortar bedding [but not backing] and removing serviceable tiles to the stores and removing rubbish / debris outside MD land complete all as specified and as directed.

M & L for coloured Glazed ceramic tiles of size 600x300x7-8mm thick as in vertical surfaces such as skirtings, dados and risers of steps, etc. set and jointed in neat cement slurry and pointed in white or colour cement to match with shade of tiles laid over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed.

M & L for coloured joint free Non skid Ceramic tiles 7 to 8 mm thick (square/rectangular), light shade area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including 15mm thick screed bed in CM 1:6 icomplete all as specified and directed.

M & L for double charged vitrified coloured ceramic tiles 10mm thick (square/rectangular), light shade area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, as in floors set and jointed neat with epoxy grout by providing 3mm spacers and masking tape shall be put before putting the epoxy grout, grout shall be througly cleaned immediatlely and pointed in white or coloured to match the shade of the tile and laid over and including screed bed or bedding layer in CM 1:6, 15 mm thick complete all as specified and as directed.

M & L for double charged vitrified coloured ceramic tiles 10mm thick (square/rectangular), light shade area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, as in dado / skirting / risers to steps, etc set and jointed neat with epoxy grout and masking tape shall be put before putting the epoxy grout, grout shall be througly cleaned immediatlely and pointed in white or coloured to match the shade of the tile and laid over and including 10mm thick backing coat in CM 1:4, complete all as specified and as directed.

M & L for 20-23mm thick, M-25 grade cement conmcrete pre-cast hydraulically pressed, designer interlocking type tiles of approved pattern and colour, set, jointed and pointed in neat cemnent slurry with grey cement and pigments laid over and including screed bed or bedding layer in CM 1:6, 20 mm thick complete all as specified and as directed.

Dismantling boarding, any description, fixed in any position with nails including battens, fillets, etc complete all as directed

M & L for preparation of surfaces making dust free, oil free and cleaning the surface properly by jet pump and cleaning agent including applying epoxy primer RCTPR-62 on the surfaces complete all as directed

M & L application of Epoxy Quartz screed RCTQZ-40 over the primer surface and the thickness should not be less than 4.5mm complete all as specified and directed

M & L application of RCTTEX COAT as top coat on the court area and the thickness should not be less than 1.5mm complete all as specified and directed

M & L for application of marking the court with water based acrylic marking paint white colour 40-50mm wide as per international standards complete all as specified and directed

Supply, install and finishing of WSF Certified "SUNFLEX" Bio-Cush wooden sports flooring system made of Canadian Hard Mapple Wood all as per international standard and quality with a total height of 76mm (45mmx70mm pinewood runners, 10mm thick full EPDM cushion pads and 21mm thick mapple wood flooring) including necessary vapor barrier on entire area complete all as directed by the Engineer-in-charge

M & L for application of new WSF (World Squash Federation) certified "Rebound" Hard plaster system only for front wall consisting of a 9mm thick base coat and a 5mm thick Finish coat fibre reinforced plaster of a total thickness of application 14mm complete all as directed

M & L for application one coat of primer and two coats of "Rebound" washable paint system to all three wall of two squash courts playing area only complete all as directed

Supply and installation of free standing 'Clear Tough' glass back wall system conforming the WSF requirement made of 12mm thick, 6400mm long and 2100mm height toughened glass back wall ith four panels, one door, four full height glass support fins, fixtures & fittings all as per international standard and quality complete all as specified and directed

Supply and installation of 6400mm width x 480mm height with wall mounting thickness of 25mm sound board made out of powder coated galvanised sheet of 24 gauge fixed with wooden frame work etc complete all as specified and directed

M & L for 25mm thick, PCC 1:2:4, type B-0, using 12.5mm graded stone aggregate as in sub base of floors, and finishing the surfaces complete all as specified and directed.

M & L for 75mm thick, PCC 1:3:6, type C-2, using 40mm graded stone aggregate as in plinth protection laid to slope in panels including joints filled with mastic filling and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for PCC 1:2:4, type B-2 using 40mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified.

Demolition of cement concrete (unreinforced) of any description from any position removing rubbish off the premises complete all as specified and directed.

M & L for old decorated surfaces and applying one or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over priming coat of exterior primer applied @ 0.90 litre/10sqm complete all as specified and directed.

M & L for Complete removal of existing treatment of any description on walls/ceiling surfaces by using vaccume based sanding machine, removal of nails and applying two coats of Acrylic Washable Distemper by using auto roller/ airless sprayer over one coat of alkali resistant primer on wall surfaces over two or more coats of Cement based Wall Care Putty on walls by using multipurpose mixture for proper mixing of putty and putty sprayer for application of putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces complete all as specified and as directed. (Note: The contractor shall carryout Distempering & allied works under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Distempering & allied works through their authorised applicators before commencement of the work to GE for approval.

M & L for preparation of old painted Wooden surfaces of any description, not otherwise described over 10cm in width or girth and applying one coat of synthetic enamel paint incl wooden putty complete all as directed.

M & L for preparation of old painted Steel surfaces of any description, not otherwise described over 10cm in width or girth and applying one coat of synthetic enamel paint complete all as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) not exc 1.5 Sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) not exc 1.5 Sqm but not exc 4.0 Sqm each complete all as specified and directed.

S & F Powder coated aluminium (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators, fixed partitions with one or more rebates including joining cleat for fixing etc. complete all as specified

S & F Powder coated aluminium (minimum thickness of powder coating 50 micron) for window and ventilator shutters, sliding type without sash bars, aluminium sections of weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long, hinges type B-21 100mm long (2 No) suitable handle (1 No) complete all as specified

S & F anodised aluminium grill (anodised transperant or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design / pattern with approved standard section and fixed to the existing window frame with CP brass / stainless ateel screws @ 200mm c/c including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening complete all as directed by the Engineer-in-Charge.

M & L for 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified

M & L for Preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treated with tar or coal tar black paint complete all as specified and directed

S & F mild steel work as in Bands, straps, hold fasts, stiffners for fencing posts, struts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M & L for 30mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides with 4mm thick decorative veneered plywood grade 1 (with BWR resin) with decorative face veneer on one face, fixed with screws to timber frame work including veneer polishing complete all as specified and directed.

S & F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned stacks or stainless steel wire staples complete all as specified and directed.

S & F Stainless steel Butt hinges, 125mm size with galvanised mild steel hinge pin complete all as specified and directed.

S & F Brass handles cast type polished bright of size 150mm complete all as directed.

S & F Brass barrel Tower Bolt of size 200mm size with cast or sheet barrel and rolled or cast bolts complete all as specified and as directed.

S & F 300mm long Brass sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as directed.

S & F Aluminium (extruded section body) Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg and fixed complete all as directed

S & F floor door stopper of aluminium body and tongue anodised with hand drawn steel spring fixed in floor overall length of cover plate 150mm complete all as specified and as directed.

S & F 4mm thick sheet glass, ordinary quality and glazing with oil putty in squares exceeding 0.5 Sqm in each pane fixed in aluminium door, windows and ventilators complete all as specified and directed.

M & L for application of high build polymer modified cement mortar 1:2.5 mixed with 3 litres of Notoband SBR of M/s Fosroc chemicals or its equivalent per bag of cement in super structure work in two layers to form 10 to 20mm thick even surface over a coat of bonding agent by mixing Nitobond SBR of M/s Fosroc chemicals or its equivalent @ 1 Ltrs + 1 Litre water + 3 Kg of cement as per manufacturers instructions complete all as directed by the Engineer-in-Charge

Demolition of Reinforced Cement Concrete of any description and in any position not otherwise specifically provided for and removing rubbish off the primises complete all as specified and as directed.

M & L for RCC 1:2:4, type B-1, using 20mm graded stone aggregate as in cast in lintels upto 1.5m span, copings, bed blocks for hold fasts, bed plates, roof kerbs and similar work including weathering, slightly rounded or chamfered angles and throating, as directed including necessary form work complete all as specified and directed.

M & L for mild steel TMT Bars of 6 to 8mm dia, as in reinforcement, cut to length, bent to shape required including cranking, bending spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

Taking down cement plaster on brick work or stone masonry walls, etc including raking out joints, hacking for key, scrubbing down with water, etc complete all as directed.

M & L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces duly mixed with and including water proofing compound as per manufacturers instructions, finished even and smooth with out using extra cement complete all as specified and directed.

M & L for rendering 10mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth with out using extra cement complete all as specified and directed.

M & L for rendering 5mm thick in CM 1:3 on fair faces of ceiling / Chajja surfaces, finished even and smooth with out using extra cement complete all as specified and directed.

M & L for preparation of newly plastered surfaces of walls/ceiling and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over priming coat of exterior primer applied @ 0.90 litre/ 10sqm over and including suitable thickness wall care putty for making good undulations to obtain smooth surfacecomplete all as directed

M & L for newly plastered surfaces of wall surfaces by using vaccume based sanding machine, removal of nails and applying two coats of Acrylic Washable Distemper by using auto roller/ airless sprayer over one coat of alkali resistant primer on wall surfaces over two or more coats of Cement based Wall Care Putty on walls by using multipurpose mixture for proper mixing of putty and putty sprayer for application of putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces complete all as specified and as directed. (Note: The contractor shall carryout Distempering & allied works under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Distempering & allied works through their authorised applicators before commencement of the work to GE for approval.

All as per item No. 51 above but on ceiling surfaces

M & L for treatment around the pipes passing through the walls (Core cut area) by wrapping around all the pipes with APL Smart Care adhere to the surfaces with APL Smart Care Acrylic Bonding Agent and placed appropriately to be grouted around the cut bores, Grouting the gaps between the pipe and the core cutting by a edual shrinkage compensated cementitious grou APL Smart Care General purpose grout that shall be poured into the gaps after fixing in place for effective leak-free shuttering complete all as per manufacturer's instructions complete all as specified and directed and by the Engineer-in-Charge.

S & F in repairs Towel Ring square with round flange complete all as directed. [Make shall be Jaquar of Cat No. ACN-1121N or its equivalent]

S & F in repairs Towel Rack 600mm long without lower hanger complete all as directed. [Make shall be Jaquar of Cat No. AKP-35781P or its equivalent]

S & F in repairs 15mm bore, Hand shower (Health faucet) (ABS Body) with 8mm dia, 1.2m long Spirochrome flex & wall Hook complete all as directed. [Make shall be Jaquar of Cat No. ALD-587 or its equivalent]

S & F in repairs 15mm bore fancy type Chromium plated two way bib taps, screwed down for iron pipe or for brass ferrule with flanges complete all as specified and directed. [Make shall be Jaquar of Cat Part No. FLR-5041PM or its equivalent]

S & F in repairs Paper holder with flap Recessed Type (Stainless steel) fixed to wall with brass screws complete all as specified and directed. [Make shall be Jaquar of Cat Part No. AHS-1553 or its equivalent]

S & F in repairs 15mm bore, angular stop cock with wall flange, cast copper alloy, chromium plated fancy type with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. [Make shall be Jaquar of Cat Part No. KUP-35053PM or its equivalent]

S & F in repairs Chromium plated Towel rail, 60cm long between flanges complete all as directed. [Make shall be Jaquar of Cat No. ACN-CHR-1111SM or its equivalent]

S & F in repairs 15mm bore pillar tap fancy type Chromium plated capstan head, screwed down, screwed for 15mm dia bore iron pipe complete all as specified and directed. [Make shall be Jaquar of Cat Part No. OPP-CHR-15005BPM or its equivalent]

S & F in repairs PVC connection 15mm size with PTMT nuts of length 600mm complete all as directed.

S & F 75mm outlet PVC [SWR] Floor Trap plain with grating including jointing with solvent cement complete all as specified and as directed.

M&L for PVC (SWR)Multi floor trap of 75mm of 75 mm dia outlet with 304 grade stainless steel square flat cut floor grating 125mm x 125mm with cockroach trap with or without hole as per requirement of site and as directed by Engineer-in- charge including jointing with solvent cement complete all as specified and as directed.

S & F 20mm outer dia 3-layer CPVC pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors including taking down old steel tubing and connections complete all as specified. [Note: Quoted rate is deemed to include for cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 wherever required as per site condition]

S & F 32mm outer dia 3-layer CPVC pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors including taking down old steel tubing and connections complete all as specified. [Note: Quoted rate is deemed to include for cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 wherever required as per site condition]

S & F in repairs gun metal, globe or gate valves, 20mm bore with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S & F in repairs gun metal, globe or gate valves, 32mm bore with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S & F 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls/ceiling including taking down old CI pipes complete all as specified and directed.

S & F 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in floors including taking down old CI pipes complete all as specified and directed.

S & F 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls/ceiling including taking down old CI pipes complete all as specified and directed.

S & F 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in floors including taking down old CI pipes complete all as specified and directed.

M & L for 110mm bore PVC (SWR) bends any radius complete all as specified.

M & L for 110mm bore PVC (SWR) bends any radius with access door complete all as specified.

M & L for 75mm bore PVC (SWR) bends any radius complete all as specified.

M & L for 75mm bore PVC (SWR) bends any radius with access door complete all as specified.

S & F 110 mm bore PVC [SWR] Junction Single [Single "T"] equal or unequal complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Junction Single [Single "T"] equal or unequal with access door complete all as specified and as directed.

S & F 75 mm bore PVC [SWR] Junction Single [Single "T"] equal or unequal complete all as specified and as directed.

S & F 75 mm bore PVC [SWR] Junction Single [Single "T"] equal or unequal with access door complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Vent cowl complete all as specified and as directed.

S & F 125/110mm bore PVC [SWR] Gully Trap with grating including jointing with solvent cement complete all as specified and as directed.

M & L for providing and injecting chemical emulsion for post construction anti-termite treatment at points of contact of wood work by chemical emulsion CHLOROPYRIFOS 20 EC at 1% concentration at the rate of 0.5 litre per each hole by drilling 6mm dia holes at a downward angle of 45 Degree at 150mm centre to centre complete all as specified and directed by Engineer-in-Charge.

M & L for providing and injecting emulsion for post construction anti-termite treatment under existing floors using emulsion CHLOROPHYRIFOS 20 EC at 1% concentration at the rate of one litre per each hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar (1:2) to match the existing floor complete all as specified and directed by Engineer-in-Charge.

M & L for providing and injecting chemical emulsion for post construction anti-termite treatment along the external wall below concrete or masonry apron using chemical emulsion CHLOROPYRIFOS 20 EC at 1% concentration at 2.25 litres per linear running metre including drilling and plugging holes with cement mortar (1:2) to match with the existing surface complete all as specified and directed by Engineer-in-Charge.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as directed

M & L for brick work with sub class 'B' bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 using old size bricks complete all as specified and directed.

M & L for brick work in half brick thick walls using sub class 'B' bricks straight or curved on plan to any radius built in Cement Mortar 1:4 including 2 Nos of 8mm dia bars at every fourth course of brick work complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as directed

S& F rolled mild steel work as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe-410-W(Gde-E-250) quality-B complete all as specified and directed

S & F Pre-painted galvalume aluminium zinc coating GI based corrugated / 'Z' profile steel sheet of 0.50mm thick, any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with and including self tapping screws complete all as specified and directed.

S & F 2.5mm thick Plain, black, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) complete all as directed

M & L for preparation of new or previously untreated steel surfaces of any description, not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

S & F in repairs Seamless False Ceiling Frame Work using GI perimeter channels of 0.55 mm thick, having one flange of 20 mm and another flange of 30 mm and web of 27 mm along the perimeter of the ceiling, fixed to wall with nylon sleeves and screws at 450 mm intervals, GI intermediate channels of size 45mm X 15mm X 0.90mm supported with GI ceiling angles of size 25mm X 10mm X 0.55mm fixed to soffits with steel expansion fasteners / GI cleats at 900 mm intervals, ceiling section of 0.55mm thick having knurled web of 50 mm and two flanges of 26 mm each with lips of 10.5 mm fixed to intermediate channel with connecting clips and in direction perpendicular to the intermediate channels at 457 mm centre to centre including fixing Gypsum board of 12mm thick conforming to IS – 2095 for false ceiling, fixed to ceiling section with 25mm dry wall screws at 230mm centres and including applying Two Coats of Acrylic Washable Distemper over a coat of Alkali Resistant Primer over suitable thickness of putty complete all as specified and as directed.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc including removing rubbish off the premises complete all as specified and directed.

M & L for 18mm to 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over and including 15mm thick screed bed or bedding layer in Cement Mortar 1:6 including dismantling old stone slabs of any description complete all as specified and as directed. [Note: Single stone slab shall be used for entire Width and Length of Steps, Window Cills, Cooking Platform etc. and joints shall match with the flooring. The edges of treads shall be bull nosed / half rounded.]

S & F High traffic tiles 600x600mm, 15mm thick as in deck flooring, floor / path, set, jointed and pointed in neat cement slurry with grey cement and pigments laid over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed

S & F in repairs Vitreous China Rimless Single Piece WC with UF soft close slim seat cover, hinges, fixing accessories, accessories set and cistern fittings of size 380x725x690mm, S Trap - 300mm and all fittings and fixtures including connection to outgoing drain including making good damaged / disturbed surfaces complete all as specified and directed. [Make shall be Jaquar of Cat Part No. ONS-WHT-10853S300UFSM or its equivalent]

S & F in repairs Vitreous china wash hand basin, Table top type including cutting for pinning in ends of brackets or erecting stand of size 495x395x150mm complete all as directed. [Make shall be Jaquar of Cat Part No. JDS-WHT-25909 or its equivalent]

S & F Soap dispenser with glass bottle complete all as directed. [Make shall be Jaquar of Cat No. AKP-35735P or its equivalent]

S & F in repairs Vitreous china wUrinal with all fixing accessories set of size 375mm x 315mm x 620mm, starwhite with grating and union for discharge pipe (excluding flushing cistern, flush pipe & waste pipe) including providing and fixing plugs, bedding urinal against wall in CM 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement complete all as directed. [Make shall be Jaquar of Cat Part No. URS-WHT132530 or its equivalent]

S & F in repairs Basin / Urinal full height partition with 8mm thick frosted glass of width 600mm and height 1950mm, 8mm thick complete all as directed. [Make shall be Jaquar of Cat Part No. JSE-CHR-810UF60H19X or its equivalent]

S & F in repairs PVC waste pipe of 32mm bore, 800mm long fixed to wash hand basin complete all as directed

Excavation in trenches not exc 1.5m wide and depth for foundations, laying of cables, pipe etc n.exc 10 Sqm on plan and getting out in soft / loose soil complete all as specified and directed.

M & L for PCC 1:3:6, type C-2 using 40mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified.

M & L for providing Precast RCC 1:2:4, Type B-1, using 20mm graded stone aggregate as in Landings, Cover Slabs [for manholes etc], Chullah Hoods, Chajjas, Water Troughs, Mangers, Shelves and similar articles with plain faces set in cement mortar 1:4 including demolition of existing cement concrete and removing debris not exc 100m complete all as specified and as directed.

M & L for PCC 1:2:4, type B-1 using 20mm graded stone aggregate as in surface channels complete all as specified.

M & L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mired /stopped ends etc. complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed. (Note: A deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming.)

Removing excavated material /soil to a distance exc 1.5 Km but not exceeding 5.0 Km and depositing where directed complete all as specified and directed

SCHEDULE 'A' PART-II [E/M Works]: M & L for Point wiring with PVC insulated unsheathed multistranded copper conductor cable FRLS grade of size 1.5 Sqmm (nominal area) 1100V grade drawn through and including concealed / surface PVC conduit of size 20mm dia medium grade including accessories fixed on wall/floor/roof, etc including provision of flush type metal GI boxes with modular cover plates, provision of PVC insulated, unsheathed multistranded copper conductor FRLS grade of size 1.5 Sqmm as earth continuity conductor and connecting to common earth dolly suitable for One light / fan point / Bell point controlled by one, one way switch including taking down old point wiring with fixtures and fittings complete all as specified and directed. [Note: Quoted rate is deemed to be inclusive for cutting through wall, chasing, pinning in making good to the disturbed surfaces whrever required]

All as per item No. 113 above but suitable for one 5/6 Amps socket outlet point controlled by one switch on the same board

All as per item No. 113 above but suitable for one 5/6 Amps socket outlet point controlled by one switch on independent board

All as per item No. 113 above but point wiring with PVC insulated, unsheathed multistranded copper conductor FRLS grade of size 2.5 Sqmm (nominal area) suitable for one 15 Amps power point on independent board complete all as specified and directed.

All as per item No. 113 above but point wiring with PVC insulated, unsheathed multistranded copper conductor FRLS grade of size 4.0 Sqmm (nominal area) suitable for power point on independent board complete all as specified and directed.

S & F modular switch single pole, 1 way, 6 Amps, 1 module

S & F modular switch 1 way, 16 Amps, 1 module single pole

S & F modular socket outlet, 6 Amps, 2/3 pin combined 2 module

S & F modular socket outlet, 6/16 Amps, 2/3 pin combined 2 module

S & F ceiling rose, 3 terminals, PVC/ polycarbonate, isolated body complete all as specified and directed

S & F modular electronic fan regulator, 120W, socket type, 2 module complete all as specified and directed.

S & F in repairs LED tube light fittings, retro bar professional WH 5700K to 6200K and 1800 to 2000 lumens of cool white comprising of batten with all accessories internally prewired and connecting up with twin core twisted copper conductor cable of suitable size including taking down old fittings complete all as specified and as directed by the Engineer-in-Charge.

S & F in repairs Building Security light LED type of minimum 3500 Lumens new generation energy saving & environmental friendly long life made up of Pressure die cast aluminium housing IP 66 protection with all accessories internally prewired and including connecting up with twin core twisted copper conductor cable of suitable size including bracket made of 32mm dia GI light grade pipe of 1.5m long bent to shape fixed with suitable MS clamps, bolts, nuts and washers duly painted including taking down old fittings with brackets complete all as specified and as directed by the Engineer-in-Charge.

S & F in repairs VTPN, MCCB DB 4 way powder coated sheet steel enclosure fitted with bus bar, DIN channel & neutral link & earth link including 4 Pole MCCB 63 Amps, 50Hz, of rupturing capacity 16 KA complete all as directed

S & F in repairs MCB DB, SPN, 8 Way, 240 Volts, with DIN Channel, Double Door with 200 Amps rated bus bar suitable for mounting MCBs flush mounted with wall complete all as specified and as directed.

S & F in repairs MCB, TP, 40 to 63 Amps, 240 Volts, 10 KA, C series

S & F in repairs MCB, SPN, 40 to 63 Amps, 240 Volts, 10 KA, C series

S & F in repairs MCB, SP 6 to 32 Amps, 240 Volts, 10 KA, C series

M & L for sub main wiring with 2 runs of single core 1100 volts grade, PVC insulated, unsheathed, FRLS copper conductor cable of size 2.5 Sqmm, drawn through and including 20mm dia concealed PVC conduit and conduit accessories including provision of 1 run of 2.5 Sqmm PVC insulated, unsheathed, FRLS copper conductor cable as earth continuity conductor including taking down old sub main wiring complete all as specified and directed. [NOTE: 3 runs of 2.5 Sqmm copper wire and 1 run of PVC conduit shall be measured as one unit length.]

M & L for sub main wiring with 2 runs of single core 1100 volts grade, PVC insulated, unsheathed, FRLS copper conductor cable of size 6.0 Sqmm, drawn through and including 20mm dia concealed PVC conduit and conduit accessories including provision of 1 run of 6.0 Sqmm PVC insulated, unsheathed, FRLS copper conductor cable as earth continuity conductor including taking down old sub main wiring complete all as specified and directed. [NOTE: 3 runs of 6.0 Sqmm copper wire and 1 run of PVC conduit shall be measured as one unit length.]

Earthing complete with Galvanized steel earth plate electrode of size 600x600x6mm thick buried directly in ground with earth pit not less than 2.25m deep below the normal ground level with top edge of plate not less than 1.5m below normal GL connected with galvanised earth wire 4.0mm dia as earth lead by means of bolts, nuts, check nuts and washers of Galvanized iron or steel all as shown in electrical plate No. 3 of SSR Part-I alongwith alternate layers of charcoal and salt connected to earthing test point all as specified or indicated including testing on completion including taking out old perished earth pits complete all as directed. [Note: The unit rate shall be deemed to include for excavation & earth work in any type of soil, PCC (1:3:6) type C1 chamber, MS angle iron frame 40x40x6mm, RCC 1:2:4 type B-1 cover 40mm thick with 8mm dia steel reinforcement bars at 150mm c/c both ways, MS handle 12mm dia, CI funnel and wire mesh, GI watering pipe 20mm dia medium grade for watering, GI protection pipe light grade 15mm dia, earthing lead upto 7.5m including taking down old earrthing sets complete all as specified in preambles of SSR Part-II and as shown in plate No. 3 of SSR Part-I.]

S & F uPVC cable trunking slotted of size 50x50mm complete with trunking accessories such as covers, bends, elbows, couplers, tees, joints, clips, internal/external angles, partition / flat junctions and branches complete all as directed

S & F in repairs LED flood light 100 Watts, 230 V, AAC outdoor type with thermal management in multiple optics and equipped with IP 66 protection with impact and corrosion resistant with driver and lamp including taking down old fittings complete all as specified and as directed by the Engineer-in-Charge.

S & F in repairs LED flood light 150 Watts, 230 V, AAC outdoor type with thermal management in multiple optics and equipped with IP 66 protection with impact and corrosion resistant with driver and lamp including taking down old fittings complete all as specified and as directed by the Engineer-in-Charge.

S & F in repairs LED flood light 200 Watts, 230 V, AAC outdoor type with thermal management in multiple optics and equipped with IP 66 protection with impact and corrosion resistant with driver and lamp including taking down old fittings complete all as specified and as directed by the Engineer-in-Charge.

Supply, install, connect, test and commissioning of weather proof LT panel board, cubical type, factory made powder coated, indoor type pedastal type dust and vermin proof, fabricated with CRCA sheet 2.0mm thick for outer and 1.6mm thick for inner door with frame made of angle iron 25x25x6mm thick and legs made of 40x40x6mm, front operated separate compartment for each outgoing feeders with locking arrangement with bus bar chamber of 3 Phase and neutral 4 strip 415 Volts with 300 Amps copper strip including necessary concrete foundation in PCC 1:2:4, type B-2 complete suitable for and including acommodating the following components complete all as specified and directed:- [a] MCCB, 4P, 160A, 25 KA - 01 No (incoming) [b] MCCB, 4P, 63A, 16 KA - 06 Nos [c] MCB, SPN, 6-32Amp, 10 KA - 02 Nos [c] Volt meter digital type 0 to 500 Volts - 01 No [d] Ammeter digital type 0 to 200 Amps - 01 No [e] Indication lamps [LED type] - 01 set [f] Complete internal copper wiring - 01 set [g] Timer switch synchronous for 0-24 Hrs suitable for street light control single phase 240V with contactor - 01 No Note: All terminations of existing cable should be provided with copper lugs / thimbles and suitable size of glands.

Supply and Laying LT XLPE insulated, PVC sheathed, bedded, galvanised steel strip or wire armoured, heavy duty, electric power cables of size 3.5 core 70 Sqmm, 1100 volts grade, with aluminium conductor laid in trenches / passing through pipe / duct / road crossing / fixed on poles / walls and connecting up with suitable glands, lugs, nuts and bolts and testing on completion including taking out old unserviceable cable complete all as specified and directed by the Engineer-in-Charge.

Supply and Laying LT XLPE insulated, PVC sheathed, bedded, galvanised steel strip or wire armoured, heavy duty, electric power cables of size 4 core 25 Sqmm, 1100 volts grade, with aluminium conductor laid in trenches / passing through pipe / duct / road crossing / fixed on poles / walls and connecting up with suitable glands, lugs, nuts and bolts and testing on completion including taking out old unserviceable cable complete all as specified and directed by the Engineer-in-Charge.

Supply and laying GI pipe 80mm bore, light for cable protection laid in trenches complete all as directed

M & L for Sand filling in trenches using dry river sand as cushioning to under ground cable including spreading, levelling and consolidation complete all as specified and directed. [Note: Punned thickness of sand shall only be measured.]

Supply and laying common burnt burnt building clay bricks of sub-class 'B' designation 75 complete all as directed

Earthing complete with Galvanized steel earth plate electrode of size 600x600x6mm thick buried directly in ground with earth pit not less than 2.25m deep below the normal ground level with top edge of plate not less than 1.5m below normal GL connected with galvanised earth strip 32x6mm as earth lead by means of bolts, nuts, check nuts and washers of Galvanized iron or steel all as shown in electrical plate No. 3 of SSR Part-I alongwith alternate layers of charcoal and salt connected to earthing test point all as specified or indicated including testing on completion including taking out old perished earth pits complete all as directed. [Note: The unit rate shall be deemed to include for excavation & earth work in any type of soil, PCC (1:3:6) type C1 chamber, MS angle iron frame 40x40x6mm, RCC 1:2:4 type B-1 cover 40mm thick with 8mm dia steel reinforcement bars at 150mm c/c both ways, MS handle 12mm dia, CI funnel and wire mesh, GI watering pipe 20mm dia medium grade for watering, GI protection pipe light grade 40mm dia, earthing lead upto 7.5m including taking down old earrthing sets complete all as specified in preambles of SSR Part-II and as shown in plate No. 3 of SSR Part-I.]

S&F SRCD with one single pole MCB (C Curve), 20A, 240V AC modular type with 30mA earth leakage protection complete all as specified and directed

RAGHU RAMA PANDA (BID ID -3474414)

S A R CONSTRUCTIONS (BID ID -3479775)

37AAOFJ7439G1ZV (BID ID -3478201)

MURALI KRISHNA ASSOCIATES (BID ID -3479737)

D NAGI REDDY (BID ID -3474530)