Construction Additional Accommodation of Govt Sen Sec School at Chhatri in Sub Tehsil Chhatri Distt Mandi SH C/o Building portion and site development

Amount

Cutting in earth work all kinds of soils and disposal of excavated earth upto a lead of any metres such as pick work , jumper work, pick work,pick jumper blasting work, blasting work in soft and hard rock conglomrate rock or saturated soil and its intermediate classification of soil including chiseling/wedging out of rocks (where blasting is prohibited) and pumping or bailing out of watering/dewatering upto any lift stacking the excavated soil clear from the edge of excavation and then returning the stacked soil in layers when required into plinth sides of foundations consolidation each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed by the Engineer-in charge within any leads including carriage of materials with in all leads, lifts and other incidentals.

Excavation in foundation, trenches etc. in earth work in all kinds of classification soil such as pick work, Jumper work, blasting work in soft and hard rock, conglomerated rock or saturated soil and its intermediate classification of soil, chieseling work and wedging out rock (where blasting is prohibited) and pumping or bailing out watering/dewatering upto any lift, stacking the excavated soil upto any lead from the edge of excavation and then returning the stacked soil in 15 (Fifteen) cm layer when required into plinth, sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing form work with steel plates 3.15mm(Three point fifteen millimeter) thick welded with angle iron in frame 30x30x5mm(Thirty millimeter into thirty millimeter into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and bellies in any height of propping and centering below supporting floor to ceiling upto floor all level and removal of the same for in situ-reinforced concrete and pain concrete work including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge in:- Vertical surface such as walls(any thickness) and the like including attached pilasters, buttersses plinth and string courses and the like

Foundation, footing basis of columns etc. and mass concrete .

Flat surfaces such as soffits of suspended floors, roofs, landings and the like Floors etc upto any thickness.

Beams, cantilever, girders and lintels sides and soffits of beams, beam haunching, cantilevers, bressumers and lintels in any depth in all height from floor..

Columns, pillars, Posts and struts, Square, rectangular or polygonal in plan

Stair cases with sloping or stepped soffits excluding landing

Edges of slabs and breaks in floors and walls in any width.

Providing 100mm (one hundred millimetre) diameter poly Vinyl chloride pipe in Weep holes in brick masonry/stone masonry, plain/reinforced concrete and retaining /breast walls etc. extending through the full width of the structure with slope of 1V:20H towards drainage face complete as per drawings and technical specifications and as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Backfilling behind abutment, wing wall, R/walls and B/walls complete as per drawings and technical specifications clause 1204.3.8 including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge.

Providing and laying cement concrete 1:3:6 ( one cement: three sand: six graded/ crushed stone aggregate 40mm (Forty millimetre ) nominal size) excluding cost of centring and shuttering in foundation and plinth as per direction of Engineer-in-charge including carriage of materials with in all leads,lifts and other incidentals..

Providing and laying cement concrete mechanically mixed and vibrated 1:5:10 ( one cement : five sand : ten graded stone aggregate 40mm.(Forty millimetre) mechanically mixed and curing complete excluding the cost of form work in foundation and plinth as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying cement concrete 1:4:8 ( one cement: four sand: eight graded/ crushed stone aggregate 40mm (Forty millimetre ) nominal size) mechanically mixed and vibrated and curing complete excluding the cost of form work in foundation and plinth as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Stone soling/boulder filling dry hand packed in under floor as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and laying reinforced cement concrete design mix M-25 (Design mix) grade mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced cement concrete work. The mix shall be designd as per requirement of I.S code and P.W.D specification. The design mix will be got approved from the Engineer - in - Charge pior to the casting . The theoritical consumption of cement fot the item shall be worked out as per approved design mix as per I.S code including carriage of materials with in all leads, lifts and other incidentals . Foundation, footing basis of columns etc. and the like and mass concrete .

Suspended floors, roofs ,landings and shelves and their support, balconies, beams, girders, breasumers and cantilevers.

Columns, pillars posts and struts .

Stair cases (except spiral stair cases) excluding landing but including preparing of the top surface and finishing of nosing.

Providing and laying reinforced cement concrete design mix M-20 grade mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced cement concrete work. The mix shall be designd as per requirement of I.S code and P.W.D specification. The design mix will be got approved from the Engineer - in - Charge pior to the casting . The theoritical consumption of cement fot the item shall be worked out as per approved design mix as per I.S code string course, copings, bed plates, anchor blocks, plain windows sills and the likesu upto floor all level including carriage of materials with in all leads, lifts and other incidentals .

Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete including cost of binding wire up to any level as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Precast concrete block masonry (including quion blocks,jamb blocks, closer etc.) with solid concrete blocks of approved size made of cement concrete 1:3:6 (1 cement:3 sand:6 graded stone aggregate 40mm (fourty millimetre) and down gauge) foundation and plinth and superstrure upto floor any level in Cement Mortar 1:6 (one cement : six sand)inculding curring complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Brick work using common burnt clay building bricks of approved kils in super structure above plinth level in Cement mortar 1:6 (One Cement : Six Sand) second Class Bricks as per the direction of Engineer-in-charge including curring and carriage of materials with in all leads, lifts and other incidentals .

Providing wood work in frames of doors,windows,clerestory windows and other frames wrought,framed and fixed in position with Ist class deodar wood within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing to existing door frames, 35 mm (thirty five millimetre) thick factory made PVC panelled door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x19mm for styles and 15mmx15mm(fifteen millimetre x fifteen millimetre) for top & bottom rails, M.S. frame shall have a coat of steel primers of approved make and manufacture M.S. frame covered with 5mm thick heat moulded PVC "C" channel of size 30mm thickness, 70 mm(seventy millimetre) width out of which 50mm shall be flat and 20mm shall be tappred in 45 degree angle on either side forming style and 5mm thick, 95mm wide, PVC sheet out of which 75mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both side to form lock rail, top, bottom and lock rail shall be provided either side of the panel 10mm thick, 20mm wide cross PVC sheet be provided as gap insert for top rail and bottom rail paneling of 5mm thick both side PVC Sheet to be fitted in the M.S. frame welded/sealed to the style & rails, joints mitred and jointed with solvent cement adhesive i/c fixing of PVC shutter with existing frame with M.S. butt hinges 100x50x1.90mm size with necessary screws etc complete. as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 19mm (nineteen millimetre) thick Commercial Board water proof shutters including fixing with nickel plated piano hinges with screws etc. complete as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 35 mm (thirty five millimetre) thick 2nd class deodar wood panelled glazed or panelled and glazed shutters for doors windows and clerestory windows. Including black enamelled iron butt hinges with necessary screws as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing angle iron cupboard frames frames manufactured from M.S.Angle iron section 25X25X5mm (twenty five into twenty five into five millimetre) thickness including hinges jamb,lock jamb,beed and if required angle thrashold of mild steel angle 25X25 mm (twenty five into twenty five millimetre) welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5 mm (two point five millimetre) thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface as directed by Engineer-in- Chargeof materials with in all leads, lifts and other incidentals

Providing and fixing 2nd class deodar wood wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm (zero point fifty six millimetre) for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screw etc complete as per specification and as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing Aluminium sheet 4 mm thick composite panel having core of polythene fixed to internal side with screws or nails as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing Plain M.S. grills of required patterns in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws. as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete.300x16mm (three hundred x sixteen millimetre) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing anodized aluminum tower bolts (barrel type ) anodized trans parent or dyed to equired shade and colour with screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. 200x10mm (Two hundred x ten millimeter)

150x10mm (One hundred fifty x ten millimeter)

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. 125 mm (One hundred x twenty five millimeter)

100 mm (One hundred millimeter)

Providing and fixing bright finished hard drawn hooks and eyes as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. 250mm (Two hundred fifty millimeter)

40 mm (forty millimetre) thick Cement concrete flooring 1:2:4 (one cement : two sand:four graded stone aggregate 20 mm (twenty millimetre) nominal size laid in one layer finished with a floating coat of neat Cement complete as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. Up to Floor any level.

25 mm (twenty five millimetre) thick wooden flooring of 1st class deodar wood laid over C.C. slab (to be paid separately) ( thinly coated with thin layer of hot bitumen blown type) @ 2.45 kg per sq m (two point forty five kilogram per square metre) including fixing of wooden planks of size 40 x 200 mm (forty into two hundred millimetre) in position over wooden frame work 750 mm x 625 mm (seven hundred fifty millimetre into six hundred twenty five millimetre) fixed in c.c. floor including planning and levelling complete as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.Up to Floor any level.

Providing and laying 10mm (ten millimetre) thick full body vetrified tiles of Asian/Johnson/Kajaria or equivalant 600x600mmx10mm (six hundred into six hundred millimetre into ten millimete) manufactured of approved shade and colour in flooring, treads of steps and landing laid over 12mm (twelve millimetre) thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete. as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.Up to Floor any level.

Providing and fixing 10mm (ten millimetre) thick full body vetrified tiles of AGL/Johnson/Kajaria/Orient Bell or equivalant 600x600mmx10mm (six hundred into six hundred millimetre into ten millimete) manufactured of approved shade and colour in skirting risers of steps and dados on 12mm (twelve millimetre) thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. upto floor any level.

Providing and fixing 40 mm(forty millimetre) thick plain framed panelling with necessary screws priming coat on unexposed surface etc. complete. In 1st class indian teak wood as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. upto floor any level.

Providing and laying 25 mm (twenty five millimetre) thick Kota stone slab flooring 20 mm (Twenty millimetre) (average) thick base of cement mortor 1:4 (1 cement :4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete as per directionof Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying Kota stone slab 25 mm (twenty five millimetre) thick in risers of steps,skirting dado and pillars laid on 12 mm (twelve millimetre) (average) thick base cement mortar 1:3 (1 cement :3 sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete within all leads, lifts and other incidentals and as per the directions of Engineer-in-Charge.

Providing and laying red sand stone slab flooring 40mm average thick on 20mm average thick base of cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab i/c rubbing and granite polish finish complete. as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 0.60mm (Zero point six zero milimetre) thick preprinterd steel sheet in roofing with hot dipped metallic zinc coasted sheet with top coat of regular modified polyester (RNP) organic coating of 20 (Twenty) microns over 5 ( five) micons primer coating P/W back coat of polyester of 5 microns over 5 microns primer coating including fixing with screws, prepainted iron J or L hooks, bolts and nuts 6mm(six milimetre) dia with prepainted limpet and rubber washer complete with all accessories as required as per specifications and as per direction of Engineer-in-Charge including carriage of materials with in all leads, liftsother incidentals.

Providing and fixing ridges or hips 60 cm (Sixty centimeter) overall with 0.60 mm (Zero point sixty millimeter) thick preprinted steel sheets in roofing with hot dipped metallic zinc coated sheets with top coat or regular modified polyester organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating + back coat of polyester of 5 (Five) microns over 5 (Five) microns primer coating including fixing with preprinted iron J or L hooks, bolts & nuts 6mm(Six millimeter) dia and preprinted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing valley 60 cm (Sixty centimetre overall 0.60mm (Zero six zero milimetre)thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 microns over 5 microns primer coating including fixing with screws, preprinted iron J and L hooks,bolts & nuts 6mm (Six milimetre)dia and prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals

Providing and fixing flushing 38cm(Thirty Eight centimeter) overall with 0.60mm ( Zero point six milimetre)thick pre painted sheet in roofing with hot dipped metallic Zink coated sheet with top coat of regular modified polyester organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with pre painted J or L hooks, bolts and nuts 6mm(Six milimetre) dia meter & pre painted G.I. limpet & bitumen washers complete with all accessories as required as per the direction of Engineer-In- charge. including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing on wall face 100mm (One hundred milimetre) dia PVC(D-Plast) rain water pipes of working pressure not less than 4.5 Kg/sqm(Four point five kilogram per square metre) including filling the joint with approved adhersive complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing on wall face (D-Plast) accessories for rain water pipes including filling the joint with approved adhesive complete as per the direction of Engineer-in-Charge inculding carriage of materials within all leads, lifts and other incidentals. PVC Plain Bend 150mm(One hundred fifty milimetre) dia.

Shoe 150mm (One hundred fifty milimetre) dia.

Providing and fixing M.S. BP Sheet 1.66 mm (One point sixty six milimetre) to 2mm (Two milimetre) thick in eves board/ facia/soffit/ceiling including cutting ,fixing and welding to steel roof members and applying a coat of red lead primer complete as per direction of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Steel work welded in built up sections, trusses and framed work,including cutting, hoisting fixing in positiobn and applying a priming coat of red lead paint as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals in: Trusses and trussed purlins in buildings including carriage of materials with in all leads,lifts and other incidentals.

Gratings framed guard bars laddeds railing brackets and similar works including carriage of materials with in all leads, lifts and other incidentals.

In beams joists,channels angles,tees,flats with connectiong plates or angle cleats as main and cross beams hip and jack rafters purlins connected to common raffers and the like.including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing75mm x 60mm (seventy five millimetre into sixty millimetre) hand rails in 1st class Indian teak wood straight length complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lift and other incidentals.

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm (twenty into ten into two milimetre) braced with flat iron diagonals 20x5mm (twenty into five milimetre) size with top and bottom rails of T iron 40x40x6mm (forty into forty into six milimetre) with 38mm(thirty eight milimetre) dia steel pully complete with bolts and nuts locking arrangements, stoppers, handles, including carriage of materials within all leads, lifts and other incidentals.

6mm (Six millimeter) cement plaster to ceiling in cement mortar 1:3 (one Cement : three Sand) as per the directions of Engineer-in-Charge including curring carriage of materials within all leads, lifts and other ncidentals.

15mm (fifteen milimetre) cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering including arises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm(eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:six sand)as per the direction of Engineer-in-Charge including curring and carriage of materials within all leads, lifts and other incidentals.

15mm (fifteen milimetre) cement plaster in single coat on the fair side of brick/concrete/stone wall for interior plastering including arises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:6 sand) as per the direction of Engineer-in-Charge including curring carriage of materials within all leads, and lifts other incidentals.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete s per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surfaces to give an even shade i/c thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth i/c applying of putty a required for making the surface as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth Priming coat with distemper primer as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease,dirt and other forein matter sand papering and knotting ready mixed paint with wood priming pink of approved brand and manufacture (Nerolac/Asian Shalimar) conforming to IS: 3536-1966 brushing as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Painting two coats (excluding priming coat) on new wood and wood based surfaces with ready mixed paint brushing to give an even shade including cleaning of oil, grease,dirt and and other foreign matter sand papering and stoping with ready mixed paint other thanwhite as per direction od Engineer-in-including carriage of materials within all leads, lifts and other incidentals.

Applying priming coat over new steel and other metal surfaces after and including preparing the surface by thoroughly cleaning oil grease dirt and other foreignmatter and scoured with wire brushes fine steel wool scrubers and sand paper complete with ready mixed priming paint brushing red leadred oxide/zinc oxide chrome as per the direction of Engineer-in-Charge including of materials within all leads,lifts and other incidentals.

Painting two coats (excluding priming coat) on new steel and other metal surfces surfaces with enamel paint brushing to give an even shade including cleaning the surface of all dirt, dust and other foregin matters Enamel paint other than white as per the direction of Engineer-in-Charge including of materials within all leads,lifts and other incidentals.

Providing plinth protection 50mm (Fifty millimetre) thick in cement concrete 1:3:6 (one Cement : three sand : six Graded crushed stone aggregated 20mm (Twenty millimetre) nominal size) mechanically mix inculding finishing the top surface of concrete smooth as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing under layer for plinth protection of 75mm (Seventy Five millimetre) thick (unconsolidated) bed of dry brick/stone aggregated 40mm (Forty millimetre) nominal size well rammed and consolidated and grouted with fine sand including preparation of ground as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Constructing course rubble hummer dressed "U" shape open surface drain with side wall 15X22cm (fifteen into twenty two)cemimeter in cement mortor 1:6 (one cement: six sand) and in side plstring with cement plaster 1:3 (one cement : three sand ) including earth work and laying 10cm (Ten Centimetre) cement concrete is 1:5:10 (one cement :five sand:ten graded stone aggregate 40mm (Forty millimetre) nominal size) and 7.5cm (seven point five centimetre) cement concrete 1:2:4(one cement :two sand ;four graded stone aggregate 20mm (Twenty millimetre) nominal size) and finishing with a floating coat of neat cement and curing complete as per standard design and as per the entire satisfaction and direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing High lax cilicate perforated water proof Board 600 x 600 x 8 mm (Six hundred xsix hundred x eight millimetre) in ceiling fixed over and including Aliminium Tee sections With Screws and including hangers and carriage of material and as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 612 mm(six hundred twelve millimetre) thick green chalk board (non magnetic with superior quality framing specially anodized aluminium profile 20x15 mm(twenty x fifteen millimetre) with corners of black surafce shall be non porous cermaic particle on the top on the green surface for the writing with chalk over 11 mmm(eleven millimetre) thick particle board which shall have backing material of galavanized sheet 0.28 mm approx. the board shall be fixed on the wall with J clamps.as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

satya paul thakur govt cont

MOHAN LAL

DALIP SINGH GOVT CONTRACTOR