REPAIRS TO MD ACCN OF KS LINE AT ZONE A UNDER GE ARMY AHMEDABAD

Amount

Taking down chowkhats or frames area exc. 1.50 Sqm and n. exc 4.00 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down shutter of any description but exc 1 sqm and n. exc. 2 sqm each complete all as specified

S&F mild steel frame work as in doors, conforming to Fe-410W (Gde E-250) including fixing of holdfast and hinges complete all as specified. (Note - Hinges shall be measured and paid separately)

S&F 30 mm thick flush door shutter, solid core construction, with block board core and plywood face panel, commercial type on both side etc complete all as specified and directed.

S & F in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S & F 100 mm long mild steel butt hinges, medium weight cold rolled complete all as specified and directed.

S&F in repairs 200 mm long Aluminium anodised barrel tower bolts complete all as specified and directed.

S&F 150 mm size aluminium anodised door handles complete all as specified and directed.

S&F in repairs 150 mm size aluminium anodised door handles complete all as specified and directed.

S & F in repairs for sliding door bolt of 300mm long plate Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

M&L for sliding door bolt of 300mm long plate Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

M&L for preparation of new wooden surface of any description n. exc. 10cm width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

S&Fin repair Floor door stopper 150mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and directed.

S&F 2nd hard wood factory made 35mm thick glazed, and skeleton door shutters open rebated & prepared to receive, glass, gauge etc. divided into squares with plain chamfered or rounded mitred and rebated any numbers and size of members of shutters as specifed in SSR Part I, Section 8, clause 8.24(a); supllied and fitted to chowkahts complete all as specified and directed.

S & F in repair for 18/19mm thick Prelaminated interior grade Block boards, grade 2 quality, decorative type with decorative face veneer on one face solid core, general purposes type fixed with screws to timber frame work complete all as specified and directed.

S & F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed

S & F Factory made solid panel PVC door /cupboard shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

M&L for Solid PVC door frame of size 50x47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube, supplied and fixed in opening as per specification and drawing complete as directed.

S&F stainless steel butt hinges medium weight 100 mm long complete all as specified and directed

S&F Aluminium anodised barrel tower bolt of extruded section 150 mm size complete all as specified and directed.

S&F Aluminium anodised barrel tower bolt of extruded section 75 mm size complete all as specified and directed.

S&F aluminium anodised ventilator with fixed aluminium frame of size 65 x 40 x 1.98mm thick fixed in vertical position with aluminium vertical members and half portion to be provided with 4mm thick pin head glass and remaining portion to be louvered using 4mm thick pin head glass and louvered portion covered with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm including necessary channel frame work, rubber gasket, aluminium beading etc including taking down existing vantilator complete all as specified and directed.

S&F steel windows with side hung shutters glazed or gauged including projection type hinges with steel handle and steel peg stay complete with glazing bars dovetailed and welding complete as specified and directed.

M&L for 3mm thick sheet glass ordinary quality and glazing with oil putty in square n. exc. 0.5 Sqm in each pane complete all as specified and directed.

S & F 25 mm dia fancy type curtain rod with brackets of stainless steeel ends etc fixed in repair complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones.

M&L for 4mm thick figured glass, pin head type and glazing with oil putty in squares n. exc 0.5 sqm in each pane complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M&L for 25mm thick Cement concrete, 1:2:4 type B-0 (12.5mm graded aggregate) including necessary form work as in flooring, surface finished rough complete all as specified.

M & L for non skid ceramic tiles (colored), 7 to 8 mm thick as in floor area of each tile exceeding 0.11 Sqm but n exceeding 0 .18 Sqm , set and jointed in neat cement slurry and pointed in white or colored cement to match including and over screed bed or beeding layers of mortar 15mm thick in CM 1:6 in floors, complete all as specified and directed.

M&L for Glazed ceramic tiles coloured (300x450mm) x 7mm thick, in dado/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick backing coat of tiles in CM (1:4) complete all as specified

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting not exc 10 cm girth in brick wall complete all as specified and directed

Taking up or down steel tubing and connections of any description and from any position incl cleaning for refixing or removing from site.

15mm bore of pipe

20mm bore of pipe

25mm bore of pipe

Supply & Fixing Unplasticised PVC pipes of pressure rating 10 kgf/cm2 any type of pipe with removal socket joint, together with all tube fittings (such as bends, elbows, tees, short pieces, I connection , caps, plugs and unions etc and fixed complete with clips wall hooks, wooden plug etc fixed to walls or in floors, ceiling and making good as specified and directed (Dismanting of tiles shall be made good)

15mm bore of pipe

20mm bore of pipe

25mm bore of pipe

All as per item No 35 above but refixing old steel tubing and connections in new or old position (Walls, ceiling, floor etc)

15mm bore of pipe

20mm bore of pipe

25mm bore of pipe

S&F in repairs vitreous china wash hand basin, white, flat back, size 550x400m excluding taps, chain & plug & porcelain stopper including brackets including cutting for pinning in ends of bracketes or erecting stand and supply and fixing waste pipe complete all as specified and directed

S&F 10 ltrs capacity PVC valve less, syphonic action type flushing cistern, low level white with inlet ball valve float and handle including brackets fixed in repairs complete all as specified and directed.

S &F in repair vitreous china water closet Squatting Orissa pattern white size 580 x 440mm with integral foot rest with P or S trap including connecting to flushing cistern low or high level, 32mm dia polyethylene lfush pipe etc compete all as specified.(excluding cost of flush tank) including provn of lime concrete bedding complete all as specified and directed.

S&F in repair cast copper alloy CP 15 mm bore angle cock with flange complete all as specified and direcrted.

S&F in repairs Bib taps (long body )fancy type cast copper alloy, chromium plated for 15mm bore pipe, screwed for iron pipes or for brass ferrule complete all as specified and as dierected.

S & F in repair 15mm bore PVC Connection with PTMT nut of length 450 mm complete all as specified and directed

S&F in repair pillar taps, cast copper alloy with capston heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly-nuts, screwed for iron pipe 15mm bore complete all as specified and directed.

Taking down cement plaster on wall of any description including racking out joints, hacking for key and scrubbing down with water etc complete all as specified and directed.

M&L rendering on fair faces of brick work in two layers i.e 10 mm thick in CM(1:6) and top layer of 05 mm thick in CM (1:4) mixed with water proofing compound in top layer @ 3% by the weight of cement or as per manufacturers instructions finishing the surface fair and even without using extra cement complete all as specified.( WPC mesured separetly)

Supply only integral water proofing compound conforming to IS: 2645 - 1975 specification complete all as specified and as directed

M&L for applying two coats of cement base paint on new plastered surfaces of wall over a coat of primer complete all as specified and as directed.

M&L 10mm thick rendering in cement mortar 1:6 on other than fair face of brick work or concrete surface finished the plastered surface even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of newly plastered or un plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer after applying 2 mm thick wall care putty to wall surface complete all as specified and directed.

M&L for preparing newly plastered or unplastered surface of wall and applying three coats of white wash complete all as specified and directed.

M & L 10 mm thick rendering cement plaster on ceiling surfaces in any position in cement mortar 1:3 , finishing the surfaces even and fair complete all as specified and directed.

M&L preparing newly plastered or unplastered surface of ceiling and applying three coats of white wash complete all as specified and directed.

Demolition of brick work built in cement mortar of any description and in any positions complete all as specified and directed.

M&L brickwork with sub class B bricks straight or curved on plan exc 6mtr mean radius built in cement mortar 1:6 by using old size bricks complete all as specified and directed.

Dismantling asbestos cement (corrugated or semi corrugated, etc)sheets in roof covering complete all as specified.

S&F 6mm thick asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc fixed with L-type or J-type or cranked hook bolts complete all as specified specified

Refixing of asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc fixed with L-type or J-type or cranked hook bolts complete all as specified specified.

S&F 6mm thick asbestos cement two piece adjustable serrated ridge for corrugated or semi corrugated sheets complete all as specified specified

S & F 0.80 mm thick plain galvanised iron (PGI) sheets having zinc coating @ 120 gram per sqm inclusive of both sides, as in ridges, hips, valley gutters, drip, straight flashing etc., fixed in any pattern complete all as specified and directed.

S&F framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, framed for ceiling; ladders; railings; framework of water tanks and similar work conforming to Fe-290 (Gde E- 165) complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10cm in width or girth not otherwise described applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

M & L for preparation of old surface and applying one coat of synthetic enamel paint (ordinary tint) on steel surfaces, complete all as specified and directed

Taking down old damaged water proofing treatment from roof surface of any description incl broken out/ loose plaster/PCC (any thickness), scrubbing down with water etc. M & L APP based polymeric membrane minimum weighing 3.0kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt. not less than 150 gms/sqm) laid by torch application over one coat of bituminous primer @ 0.30 kg/sqm over and including 15 mm thick cement plaster in CM 1:4 including water proofing compound @2% by weight of cement, applying a coat of aluminium paint as per the makes approved by the Engr-in- charge including disposal of debries exc. 50 mtr and n.exc. 100 mtr from starting point complete all as specified and directed.

M & L for PCC 1:2:4 type B0 using 12.50 mm graded stone aggregate in roof etc as levelling coarse etc. all as specified and directed by Engineer-in charge

Taking down eaves gutters and rainwater, waste & soil pipe with fittings from wall, trenches of any description including fittings complete all as specified and directed.

S & F in repairs PVC(SWR) 110 mm dia soil waste and rainwater drainage pipes single socketed in any length with rubber ring joint laid in floor or fixed on walls complete all as specified and directed.

S&F 110mm dia PVC (SWR) branch piece single (single 'Y') equal or unequal with acess door complete all as specified and directed.

S & F in repairs PVC(SWR) 75 mm dia soil waste and rainwater drainage pipes single socketed in any length with rubber ring joint laid in floor or fixed on walls complete all as specified and directed.

S & F in repair 75 mm bore PVC (SWR) bends 75mm ( any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed.

S & F in repair 75 mm bore PVC (SWR) branch pieces, single ( equal or unequal), ordinary or inverted ( spigot or socket type) or with parallel branches complete all as specified and directed.

S&F in repairs 75mm bore PVC (SWR) floor trap long body type with grating including jointing with solvent cement complete all as specified and directed.

S&F grating PTMT square of size 150mm complete all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specially provided complete all as specified and directed.

M&L 75mm thick PCC (1:3:6) type C2 as in plinth protection/footpath using 40mm graded stone aggregate finishing cement concrete surface even & smooth without using extra cement including bitumen filling in between panels etc complete all as specified and as directed.

M&L for preparation of old decorated plastered or unplastered surfaces of walls including cornices etc by brooming down or steel wire brushing scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of oil bound distemper complete all as specified and directed.

All as per item No 75 above but one coat of cement based paint on walls complete all as specified and directed.

All as per item No 75 above but one coat of white wash on ceilings.

All as per item No 75 above but one coat of white wash on walls

M&L for preparation of old painted wood and wood based surfaces by knotting, stopping etc of any description over 10 cm width or grith and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for 15mm thick rendering on vertical side of sunken floor of brick/ concrete surfaces in CM (1:3) mixed with water proofing compound as per manufacture instruction and finished even and smooth without using extra cement complete all as specified. (Note : WPC shall be measured and paid seperately)

M&L for PCC 1:1½:3 nominal mix type A-0 using 12.5 mm graded stone aggregate mixed with water proofing compound as per manufacture instruction on bottom of sunken portion with slope towards spout including applying two coats of polymeric base chemical in the top surface of PCC and side of sunken portion complete all as specified. (Note : WPC shall be measured and paid seperately)

M&L for PCC 1:5:10 type E-2 (using 40 mm graded brick aggregate) as in lean concrete in sunken floors complete all as specified and directed.

S&F 50 mm bore pipe medium grade galvanised iron water tube with all fittings laid in floors fixed to wall for spout etc complete including taking down old pipe complete all as specified and as directed.

M&L filling surface cracks not exc 5 to 7 mm wide with “Dr fixit cracks X power or equivalent polymer modified cracks filler all as per manufacturer instructions and as directed.

M & L for guniting for shortcrete 1:2 (CM) mixed with epoxy resin and hardner (manufactured by FOSROC/MC BAUCHEMIC/ CICO/PIDILITE) @ 2% by weight of cement in equal proportion using shortcrete pumps allied equipment, in thickness 30 mm all as per manufactureres instruction (upto 10 m height) including necessary chipping/taking down loose concrete all as directed.

S & F mild steel Welded steel wire fabric of weight exe 3.5 kg but n. exc 4 kg/sqm fixed to steel members with spikes complete all as specified

Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided complete all as specified and directed.

Dismantling of wrought iron work or mild steel work of any description not otherwise provided complete all as specified and directed.

M & L for Rolled sections as in main and cross beams, hip and jack rafters; purlins for chajja where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to Fe-410-w (Gde E- 250) quality A complete all as specified.

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Demolition of stone slab and tiles of any description or thickness as in floors, apron etc laid, bedded and pointed in any mortar complete all as directed.

M&L for pre-polished kota stone slab 20-25mm thick as in shelves including cutting grooves in wall making good disturbed surface, matching with existing surface etc; rubbing and polishing complete all as specified

Supply & Fixing in repairs PTMT Swivel Shower rose, 15 mm dia ( Minimum wt 40 gms), all as specified.

Supply & Fix in repairs bevelled edge mirror of size 600 x 450mm and any thickness, mounted in 6mm thick plywood/AC building board with PVC coloured frame all around, complete all as specified and directed.

S&F in repair health faucet with one meter tube and hook complete all as specified and directed

Shree Krushna Supply Corporation

megha enterprise

r s corporation