Development of civil and electrical charging infrastructure for operation of electric buses at HRTC Workshop Dharamshala, Distt. Kangra HP

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundations, trenches etc. in earth work in all kind of soils, such as pick work, jumper work, blasting work, by blasting or chieling and pumping bailing, dewatering where ever required etc. complete and lift up to all heights and then clear from the edge of the excavation and then returning the stacked soil in 15 cm, layers, when required in to plinths sides of foundations etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth up to approved dumping site , including all leads, lifts and carriage of materials, complete in all respect as per entire satisfaction of the Engineer-in charge. Any loss of Govt.and private property during the execution of work shall be the absolute responsibilty of the contractor.

Providing and laying in position cement concrete Mechnically Mixed and vibrated of specified grade excluding the cost of centering and shuttering - All work up to plinth level :- 1:4:8 (One Cement isto Four coarse sand isto Eight graded stone aggregate) 40 mm (Forty milimeter) nominal size, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and laying in position cement concrete Mechnically Mixed and vibrated of specified grade excluding the cost of centering and shuttering - All work up to plinth level :- 1:3:6 (One Cement isto Three coarse sand isto Six graded stone aggregate) 40 mm (Forty milimeter) nominal size, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and laying in position cement concrete Mechnically Mixed and vibrated of specified grade excluding the cost of centering and shuttering - All work up to plinth level :- 1:3:6 (One Cement isto Three coarse sand isto Six graded stone aggregate) 20 mm (Twenty milimeter) nominal size, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and laying in position specified grade of reinforced cement concret1:1.5:3(One cement isto One point Five coarse sand isto Three graded stone aggregate) 20 mm(Twenty milimeter) nominal size :-All work up to plinth level :- including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing steel reinforcement for R.C.C. work including bending, binding and placing in position including cost of binding wire complete, upto floor all levels :- Thermo-Mechanically Treated bars of grade Fe-500D or more., including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Centering and shuttering including strutting, propping etc. and removal of form for :- (a) Foundations, footings, bases of columns, etc. upto plinth level. for mass concrete, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Centering and shuttering including strutting, propping etc. and removal of form for :- (b) Walls (any thickness) including attached pilasters, buttersses, plinth and string courses etc., including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Centering and shuttering including strutting, propping etc. and removal of form for : - (c) Lintels, beams, plinth beams, girders, bressumers and cantilevers, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Dry stone pitching 22.5 cm (Twenty two point five centimeter) thick including supply of stones and preparing surface complete, stone for pitching :- 90mm to 45mm (Ninety milimeter to Forty five milimeter),including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm (Fifty milimeter) thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete. all as per direction of Engineer-in-Charge:-100 mm (One hundred milimeter) thick C.C. paver block of M-30 grade with approved color design and pattern ,including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

15 mm (Fifteen milimeter) cement plaster in two coats under layer 12 mm (Twelve milimeter) thick cement plaster 1:4 (One cement isto Four coarse sand) and a top layer 6 mm (Six milimeter) thick cement plaster 1:4 (One cement isto Four coarse sand) finished rough with sponge, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Making plinth protection 50mm thick of cement concrete 1:3:6 (One cement isto Three coarse sand isto Six graded stone aggregate) 20 mm (Twenty milimeter) nominal size over 75mm (Seventy five milimeter) thick bed of dry brick ballast 40 mm (Forty milimeter )nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth,ncluding all leads, lifts and carriage of materials, in all respect of as per entire satisfaction of the Engineer in charge.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete:-Hot finished seamless type tubes, including all leads, lifts and carriage of materials, in all respect of as per entire satisfaction of the Engineer in charge.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete:-Hot finished welded type tubes, including all leads, lifts and carriage of materials, in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete,including all leads, lifts and carriage of materials, in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 (Twelve) metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required,including all leads, lifts and carriage of materials, in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing 1 mm (One milimeter) thick M.S. sheet sliding-shutters, with frame and diagonal braces of 40x40x6 mm(Forty into Forty into Six milimeter) angle iron, 3 mm (Three milimeter) M.S. gusset plates at the ns and corners, 25 mm (Twenty five milimeter) dia pulley, 40x40x6 mm (Forty into Forty into Six milimeter) angle and T- iron guide at the top and bottom respectively, including applying a priming coat of approved steel primer,including all leads, lifts and carriage of materials, in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm (Thirty five into Thirty five into Five milimeter) , joints mitred and welded by angle iron 35x35x5 mm (Thirty five into Thirty five into Five milimeter) or 35x 5 mm (Thirty five into Five milimeter) flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge, including all leads, lifts and carriage of materials, in all respect of as per entire satisfaction of the Engineer in charge

Providing and fixing 1mm (One milimeter) thick M.S. sheet door with frame of 40x40x6 mm (Forty into Forty into Six milimeter) angle iron and 3 mm (Three milimeter) M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer,Using flats 30x6mm (Thirty into Six milimeter) for diagonal braces and central cross piece, including all leads, lifts and carriage of materials, in all respect of as per entire satisfaction of the Engineer in charge

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :-250x16mm (Two hundred fifty into Sixteen milimeter) , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :- 200x10mm (Two hundred into Ten milimeter), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :- 150x10mm (One hundred fifty into Ten milimeter),including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :-125mm (One hundred twenty five milimeter), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :-100 mm (One hundred milimeter),including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

12 mm (Twelve milimeter) cement plaster of mix : 1:4 (One cement isto Four coarse sand) including all leads, lifts and carriage of materials, complete in all respect:- including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Finishing walls with water proofing cement paint of required shade:- New work (Two or more coats applied @ 3.84 kg/10 sqm complete in all respect:- including all leads, lifts and carriage of materials, in all respect of as per entire satisfaction of the Engineer in charge.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications Painting Steel work with Deluxe Multi Surface Paint to give an even shade:- Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture including all leads, lifts and carriage of materials, in all respect of as per entire satisfaction of the Engineer in charge

Please Enable Macros to View BoQ information