CWE KOTA/KOTA-70 OF 2019-20 SPECIAL REPAIR TO BLOCK NO P-15 IN KHEMKARAN VIHAR AT MIL STN KOTA

Amount

B/R ITEMS Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles and removal all rubbish material outside of MD Land complete all as specified and directed.

Demolition of existing roof treatment /lime concrete PCC padding over RCC roof removing complete layers of bitumen under concrete /PCC Padding, sweeping the surface with wire brusses and cleaning with water to remove all loose dirt etc and removing the rubbish off out side MoD land complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness below or above ground level and removal all rubbish material complete all as directed.

Demolition of RCC (over Head water tank) of capacity 500 Ltrs and in any position not otherwise specifically provided for is reinforced (reinforcement cut as required to facilitate demolition) complete all as specified and directed.

Taking down chowkats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed.

Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed.

Taking down cement plaster any description, on brick or stone walls, etc. including raking out joints, hacking for key & scrubbing down with water, etc. & removing rubbish off the premises, complete all as directed.

Taking down shutter of any description exc. 1 sqm but n.exc 2 sqm each and removing from site complete all as specified and directed. .

Taking up or down steel tubing and connections including cleaning for refixing or removal complete all as specified and directed :-

15mm bore.

20mm bore.

Dismantling of 75mm bore cast iron drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed.

Dismantling of 100mm bore cast iron drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed.

Dismantling of cement concrete tiles in floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling wrought iron, or mild steel work of any description not otherwise provided for complete all as specified and directed.

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 complete all as specified and directed.

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan to any radius in half brick thick wall, built in cement mortar 1:4 complete all as specified and directed.

S & F 35mm thick factory made IInd Class Hard wood (Hollock) plain framed, panelled door shutters single panel with lock rail and panel of 9mm B.W.P. marine grade plywood bonded with high quality liquid phenol formaldehyde synthetic resin adhesive conforming to IS-710 or 12mm thick particle board veneered with commercial veneering on both faces. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.

S & F 35mm thick factory made glazed and skeleton door shutters open rebated of second class hard wood rail and styles(Hollock), prepared to receive glass/gauge etc without sash bars, edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. Note :- S & F Glass/gauge shall be measured and paid for separately

S & F in repair for 17/19 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

S & F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing as applicable to item 08095 given in SSR Part – II (2010) complete all as specified and directed.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppy and fixing in the frame at site complete all as per specifications and drawings as applicable to item 08080 given in SSR Part – II.

Supply fabrication and fixing powder coated (Thickness of powder coating not less than 50 micron) aluminium door shutters, side hung type without sash bars, aluminium section weighing 0.55 Kg/RM including necessary jointing cleats, glazing clips, rubber neoprene packing, powder coated anodised aluminium snap beading, screws, powder coated aluminium fittings, such as handle (01 No for each leaf) etc complete all as specified and directed. (Note :- Glazing/wire mesh shall be measured and paid separately under respective items of Schedule.

Supply fabrication and fixing powder coated (Thickness of powder coating not less than 60 micron) aluminium anodized grill of design DG-104 pattern, made out of 10 mm dia rod fixed with and including stranded aluminium frame of 'F' section of size 23.04 x 15.3 x 1.4mm thick all as per manufacturere's instrucstions complete all as specified and directed.

S & powder coated (Thickness of powder coating not less than 50 micron) aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S & F in repair for kitchen plate rack of size 31 inch x 36 inch x 10 inch with partition for small/large plates fabricated out of Ist quality 24 gauge thick stainless steel sheet complete all as specified and directed.

S & F in repair 20mm dia fancy CP curtain rod with bracket and screw with necessary all fittings complete all as specified and directed.

S & F 150mm (overall length of cover plate), floor door stopper of aluminium alloy body and tongue, brass body and tongue, with hard drawn steel spring, fixed in floor complete all as directed.

S&F 5.5mm thick sheet glass n exc. 0.50 sqm, ordinary quality and glazing in Aluminium windows, complete all as specified and directed.

S & F 100 mm size butt hinges, medium weight, colled rolled mild steel & ISI marked complete all as specified and directed.

S & F 300 mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 16mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S & F in repairs chromium plated brass tubular towel rail 20mm dia, “D” type for wash hand basin centre holed fixed to iron pipe complete all as specified and directed.

S & F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples complete all as specified and directed.

S & F in repair galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanized wire staples in door and steel window complete all as specified and directed.

M&L preparation new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over and including one coat of pink primer complete all as specified and directed.

M&L preparation old painted wooden or wood based surfaces of any description not exc 10cm width or girth when unconnected with other painting or when painted in a different tint and applying one coat of synthetic enamel paint over and including one coat of red oxide complete all as specified and directed.

M&L preparation new or previously untreated steel surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chorme primer complete all as specified and directed.

M&L preparation old or previously untreated steel surfaces of any description not otherwise described over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for preparation of newly plastered surfaces of wall and applying two coats of distemper with distemper oil emulsion white or tinted over and including one coat of 1mm thick wall care putty, complete all as specified and directed.

M & L for preparation of newly plastered surfaces of wall and applying two coats of exterior emulsion paint over a coat of primer, complete all as specified and directed. (Make : Apex Ultima of Asian, weather shield MAX of ICI/Dulux, weather coat ling life of Berger, Acroguard 3X of Acro paint. Note:- Paint and primer shall be of same make.

M&L for complete removal of existing treatment on walls, chajjas etc including cleaning of any mortar drops, fungus efflorescent salts etc and preparation of old plastered surfaces and applying two coats of distemper with distemper oil emulsion white or tinted over and including one coat of 1mm thick wall care putty complete all as specified and directed.

M&L for preparation of old surfaces of walls, plastered or unplastered by brooming down or steel wire brushing, scapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots & applying one coat of white wash etc. complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying three coats of white wash on ceiling complete all as specified and directed.

M&L for preparation of old plastered or previously untreated surfaces of ceiling and apply one coat of white wash complete all as specified and directed.

S & F 150mm long mild steel, barrel tower bolt, stove enamelled black with bright bolt and fixed complete all as specified and directed.

S & F 150mm size mild steel, oval type, bow handle, stove enamelled black anodised complete all as specified and directed.

S & F 300mm size ordinary mild steel, rat tailed rod pattern spring incluidng roller and roller plate welded to mild steel frame complete all as specified and directed.

S & F 150mm long aluminium anodized barrel tower bolt of extruded section ISI marked complete all as specified and directed.

S&F 150mm size aluminium handles, cast type anodised complete all as specified and directed.

M & L for PCC (1:2:4) type B-0 using 10/12.5 mm graded stone aggregates laid over roof slab after applying cement slurry for filling undulations finished even and smooth without using extra cement complete all as directed.

M&L screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:4, over RCC roof slabs for laying water proofing treatment mixed with using water proofing liquid @ 150 ml per bag of cement complete all as directed. (Note : Water proofing liquid shall be measured and paid separately)

Supply only integral water proofing liquid of Dr Fixit/Sika/Fosroc complete all as specified and directed.

Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm of make super thermolay manufactured by STP Ltd or ‘Hyper Plas’ (Polyster) manufactured by M/S IWL Ltd or ‘Shaliplas’ (polyester) manufactured by M/S Capital Steels and chemicals Pvt Ltd or Hydro Stop manufactured by TIKITAR DANOSA (INDIA) Pvt Ltd as approved by GE, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over compatible bitumen primer (Bitumen primer shall be TANK MASTIC of M/S STP Ltd or ‘EMW FLATE’ of M/S Texas India Ltd} at the rate of 0.40 Kg/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions complete all as directed. Note: (i) Coved fillets in PCC(1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces and thereafter surface painted with hot paving bitumen of Grade 30/40 confirming to IS-73, [email protected] Kg/Sqm over a coat of bituminous primer confirming to IS-3384 applied @ 0.40 Kg/Sqm. (ii) Polymeric membrane shall be taken to a height of 45cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing. (iii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iv) In case of stone masonry parapet wall etc a groove of size 25mmx25mm(minimuim) shall be made in coved fillet at the junction of roof and parapet wall/mumty Chimny/other vertical surfaces and polimeric membrane insterted in groove and sealed with paving bitumen (v) Exposed surfaces of APP membrane shall be applied with one coat of bituminous aluminium paint @ 150 ml/Sqm. (vi) Above aspects are deemed to be included in quoted rate.

M & L for water proofing treatment in sunken floors as described hereunder:- (i) Sunken floor and sides upto finished floor level shall be plastered with 15mm thick cement plaster in mortar 1:4 mixed with water proofing compound @ 3% by weight of cement. (ii) Preaparing plastered surfaces and providing APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm of make super thermolay manufactured by STP Ltd or ‘Hyper Plas’ (Polyster) manufactured by M/S IWL Ltd or ‘Shaliplas’ (polyester) manufactured by M/S Capital Steels and chemicals Pvt Ltd as approved by GE, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over compatible bitumen primer (Bitumen primer shall be TANK MASTIC of M/S STP Ltd or ‘EMW FLATE’ of M/S Texas India Ltd} at the rate of 0.40 Ltr/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions, including preparation of surface by removing the existing treatment, complete all as specified and as directed. Note: (i) Polymeric membrane shall be laid in sunken floor and on sides upto finished floor level. (ii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iii) Above aspects are deemed to be included in quoted rate. (iv) Supply only water proofifng compound shall be measured and paid separately. (v) 32mm dia GI Pipe shall be provided in Sunken slab 30cm projected beyond ext wall face. Note : Slab area only will be measured for payment purpose.

S&F for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete con- forming to Fe.290.Gde-E-165 complete all as specified and directed.

M & L for framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F for welded steel wire fabric (Weight n exc 4kg/sqm) to steel members complete all as specifieid and directed.

M&L for precast (factory casted) cement Concrete kerb stone casted in PCC (1:2:4) type B-1 using 20mm graded stone aggregate with plain or interlocking joints (as directed), making groove in ground of desired dimension, placing in erect position Kerb stone in edging and set and jointed in cement mortar 1:4, making good distrubed surface of ground complete all as specified and directed.

M & L for 100mm thick PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base complete all as specified and directed.

M & L for 25mm thick PCC 1:2:4 type B-1 using 25mm graded stone aggregate as in floors, surfaces finished even and rough to receive the topping layer complete all as specified and directed.

M&L for 60mm thick precast glazed interlocking paving blocks factory casted using grey cement with pigment, machine pressed confirming to IS-15658-2006 and of shape haxagon/ triangular/ zigzag/ I-shaped etc. as directed having compressive strength not less than 350 Kg/ Sqcm (M-35) laid over and including 25 to 30mm thick layer of sand cushioning including filling the interstices with & including sand complete all as specified and directed by Engineer-in-Charge.

M & L for screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6, for laying floor finishes/tiles complete all as specified and directed.

M & L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and directed.

M & L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and directed.

M & L for glazed ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as on vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed.

M&L Green granite slab 18 to 20 mm thick (of any type table rubbed and polished) in cooking platforms and like set in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with complete all as specified and directed.

M & L for 50mm thick PCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified and directed. Note:- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3.0m in length. Joints of 6mm wide and 10mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

M&L rendering 15 mm thick in two layers on stone masonry surfaces or on other than fair faces of brick masonry first layer 10mm thick in cement mortar 1:6 and second layer 5mm thick in CM 1:4 mixed WPC finished even and smooth without using extra cement complete all as specified and directed. (Note :- Supply only WPC shall be measured and paid separately)

M & L rednering 10mm thick in CM 1:6 on brick masonry surfaces or on other than fair faces of brick masonry finished even and smooth without using extra cement. complete all as specified and directed.

M & L for 10mm thick rendering in CM 1:4 on stone masonry surfaces, wall surfaces or on other than fair faces of brick wall surfacee for fixing tiles etc. complete all as specified and directed.

M & L for 5mm thick rendering in CM 1:4 on concrete surfaces on ceilings, finished even and smooth without using extra cement complete all as specified and directed.

M&L coloured glazed ceramic tiles (350x250x7mm)/450 x 350 x 7mm thick as in vertical surfaces etc. set & jointed in neat cement slurry & pointed in white or coloured cement to match the shade of tiles complete all as specified and directed.

S&F 20mm bore steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed.

Fixing only 20mm bore steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed.

S & F in repairs white Vitreous china wash down water closet pan (Orrissa pattern) including connection to drain or out going pipe and to flushing pipe, antisyphonage pipe etc plastic water closet seat, white/black, closed pattern with flat bottom and cover and mild steel chromium plated complete all as specified and directed.

S&F in repairs, PVC low level cistern 10 litres capacity, valve less, symphonic action type with float, handle including 32mm dia PVC flush pipe of polyethylene of low or high density & bracket etc complete all as specified and directed.

S & F in repairs sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm including PVC waste pipe complete all as specified and as directed .

S & F in repair brass chromium plated shower rose 125 mm size with or without swivel joints of any size, including fixing to steel pipe or union complete all as specified and directed.

S & F in repairs PVC connection 15mm dia 450mm long with PTMT check nut and washer etc complete all as specified and directed.

S & F in repair bib taps 15mm bore cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe of for complete all as specified and directed.

S & F in repairs 15mm bore stop valve cast copper alloy chromium plated, fancy type screwed down high pressure long shank and cup concealed type with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed.

S & F in repairs 15mm bore stop valve cast copper alloy, screwed down high pressure long shank and cup concealed type with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed.

S & F in repairs 20 mm bore dia stop valve cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed.

S & F 500 litres, rotational moulded polyethylene water storage tank (Cylindrical vertical with closed top), hoisted and fixed in position complete all as specified and directed. Note : PVC tanks shall be ISI marked and having two layers.

Supply and Laying of CPVC Pipe Outer Diameter 16mm Pipes SDR-11 & plain CPVC SDR 11 fitting on wall/ceiling or laying in floor complete all as specified and directed.

Supply and Laying of CPVC Pipe Outer Diameter 16mm Pipes SDR-13.5 & plain CPVC SDR 11 fitting on wall/ceiling or laying in floor complete all as specified and directed.

S & F 20mm bore ball brass valve high pressure with polythene float and fly nut complete, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S & F in repairs PVC (SWR) floor trap 75mm dia outlet plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete 1:2:4, type B-1 complete all as specified and directed.

S & F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed for following sizes:-

75mm bore.

110mm bore.

S & F PVC(SWR) junction single (Single 'T') equal or unequal with access door complete all as specified and directed for following sizes:-

75mm bore.

110mm bore.

S & F 75mm bore PVC(SWR) bend of any radius complete all as specified and directed.

M&L rendering 10mm thick, in cement mortar 1:4 over RCC roof slabs(parapet etc) for laying water proofing treatment mixed with using water proofing liquid @ 150ml per bag of cement complete all as specified and directed. Note:- Water proofing liquid shall be measured and paid separately.

M&L rendering 15mm thick in CM 1:6 on stone masonry surface or on other than fair faces of brick masonry finished even and smooth without using extra cement complete all as specified and directed.

M & L for PCC Type D2 1:4:8 (40mm graded agreegate) cement concrete in foundations, filling and mass concrete, complete all as specified and directed.

E/M PORTION Taking down the existing old unserviceable point wiring of any description for old light/fan/socket/power including terminal boards, switches, sockets, ceiling roses light fitting etc and making good disturbed surfaces of walls, ceiling etc complete all as specified and directed.

Taking down the existing unserviceable MCB, DBs SPN with MCBs any type after disconnecting incoming and outgoing connections, complete all as specified and directed.

Taking down sub main wiring of any sizes, complete all as specified and directed.

Taking down carefully old ceiling fan/exhaust fan and refixing the same after reapri, complete all as specified and directed.

M & L for point wiring complete with 1.5 Sqmm single core unsheathed stranded copper conductor cable of 1100 volts grade PVC insulated and unsheathed FRLS cable enclosed in and including PVC casing and capping not less than 20mm width with MS sheet metal sunken switch/terminal box 1.2mm thick and phenolic laminated sheet cover 3.0mm thick and brass screws with cup washers with all necessary wall cutting and making good distrubted surface as directed, including all necessay wall cutting and making good disturbed surface including 1.5 Sq.mm solid copper conductor with green PVC FRLS insulated unsheathed earth continuity conductor to common earth & connecting to earth dolly for the following :-

One light/bell point controlled by one, one way switch.

One ceiling fan/exhaust fan point.

One 3 pin 5 Amps socket out point on the same board.

One 3 pin 5 Amps socket outlet on independent board.

M & L for point wiring complete for 15 Amps socket outlet on independent board with with 2.5 Sqmm single core unsheathed stranded copper conductor cable of 1100 volts grade PVC insulated and unsheathed FRLS cable enclosed in and including PVC casing and capping not less than 20mm width with MS sheet metal sunken switch/terminal box 1.2mm thick and phenolic laminated sheet cover 3.0mm thick and brass screws with cup washers with all necessary wall cutting and making good distrubted surface as directed, including all necessay wall cutting and making good disturbed surface including 2.5 Sq.mm solid copper conductor with green PVC FRLS insulated unsheathed earth continuity conductor cable to common earth & connecting to earth dolly.

M & L switch piano flush type 5 Amps, single pole, one way, 230 Volts complete all as specified and directed.

S&F, switch socket combination, 5 Amps 230 volt 3 pin flush type universal complete all as specified and directed.

S&F, switch socket combination, 5 and 15 Amps, 2 in 1, 230 volt 3 pin flush type universal complete all as specified and directed.

S & F lamp holder, PVC / polycarbonate type with back plate suitable for Batten fittings complete all as specified and directed.

S & F ceiling rose, surface bakelite 65x50mm three terminal, PVC / poly carbonate isolated body, complete all as specified and directed.

S&F electric bell, AC 230 V, single pole type, complete all as specified and directed.

S & F switch bell push, AC 230V single pole 5 Amp, complete all as specified and directed.

S & F for submain wiring with 2 single core PVC insulated & PVC unsheathed FRLS cable 1100 Volt grade with 06 Sqmm copper multistranded conductor drawn through and including PVC conduit/casing-caping fixed on surface to wall/ ceiling by means of MS screws and saddles including one run of 6 Sqmm single core multistranded copper conductor 1100 volts grade PVC insulated and unsheathed FRLS cable as earth continuity conductor to common earth and connecting to earth dolly and including taking down old u/s sub main wiring complete all as specified and directed. Note: - Two runs of main cable, one run of earth continuity conductor and one run of conduit/casing-caping will be measured and paid as one length only.

Supply and fix wall mounted LED battern fitting, extruded aluminium heat sink for efficient heat dissipation with internal electronic driver, 20 Watt, 3000K, complete all as specified and directed. {Model/Make : Product Cat Part No LHEWB6IN1W020 of make Havells or equivalent as specified in Appendix 'D'.

S & F sheet metal enclosure single door DB TPN 04 way, 415 volts protection class IP-30 made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted confirming to IS-13032, IS 8623, BS-5484 with tinned copper bus bar of 200 Amps capacity completed all as specified and directed.

S & F sheet metal enclosure double door DB SPN 8 way, 240 volts protection class IP-43 made out of CRCA mild steel sheet surface with epoxy powder coated surface confirming to IS-13032, IS 8623, BS-5484 with tinned copper bus bar of 200 Amps capacity all as specified and directed.

S&F MCB TPN 63 Amps, 415 Volts, C-series breaking capacity 10 KA, complete all as specified and directed.

S&F MCB SPN 6-40 Amps, 240 Volts, C-series breaking capacity 10 KA, complete all as specified and directed.

S&F MCB SP 6-32 Amps, 240 V, C-series breaking capacity 10 KA, complete all as specified and directed.

M & L for earthing complete with galvanized steel earth plate 60 cm X 60 cm X 6 mm thick buried vertically in ground to depth not less than 2.25 metres deep below ground level, with top edge of earth plate not less than 1.5 m below ground level, connected to galvanized iron strip 25x4mm earth lead by means of bolts, nuts, check nuts and washers of galvanized iron or steel besides welding at all joints as shown in drawing and including excavation and earth work, GI pipe light grade 50mm bore for protection of strip and connected to continous earth lead on pole/test point, supplying and laying charcoal dust common salt PCC 1:3:6 type C1, chamber and MS angle iron frame 40x40x3mm and RCC cover 40mm thick (1:2:4) type B1 using 20mm graded stone aggregate reinforced with 6mm dia round bars @ 75mm C/C both ways with MS handle 12mm dia, PGI funnel and wire mesh, 20mm dia GI pipe medium grade for watering all as shown in electrical plate No 3 on srl page No 497 of SSR Part I (2009) drawing and connection to earth test point including testing complete all as specified and directed. Note :- (i) The cost of earth lead /strip and GI pipe for protection of earth lead/strip upto 7.5m is included in the quoted rate. (ii) The cost of excavation, earth work is included in the quoted rate.

TARKESHWAR DASS CONSTRUCTION COMPANY

L P Singh and Co.

ONKAR ENGINEERS

SINGH ENTERPRISES

Ganesh Contruction

Pioneer Enterprises