REPAIR/REPLACEMENT OF STREET/SECURITY AND GARDEN LIGHTS AT ZONE 2 (A, B), ZONE 3 (A,B) AND ZONE 4 AND REPAIR/MAINTENANCE OF EXTERNAL ELECTRIC SUPPLY, OVER HEAD LINES, UG CABLE AND ALLIED WORKS AT ZONE 5 AND ZONE 1 (A, B, C) UNDER GE (SOUTH) TEZPUR

Amount

Supply and fixing in replacement to old by new Danger notice plate of 1.6mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with M.S. clamps, bolts and nuts of approved size, for HT, 25x20cm size all as specified and directed. Note :- Instruction shall be written in three lauguage Hindi, English and Assami on notice board.

Labour to re-stringing/ tilting, clamping, bending , jumpering, etc to be removing excess sag of loose ACSR of over head line upto permissible sag at camp area using accessories, T&P such as manila rope, puller and tripod etc upto permissible sag between two poles to continiously upto terminating point of tightening of stay strand in proper angle etc all as per site requirement and directed Note :- (i) Three/ four/six/eight runs of ACSR shall be measured against one unit. (ii) Quoted rates shall be included for all required T&P and safety equipment. (iii) Span Between two consecutive poles shall be measured as one unit.

Supply and fixing in replacement to old by new Danger notice plate of 1.6mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with M.S. clamps, bolts and nuts of approved size, for LT, 20x15cm size all as specified and directed. Note :- Instruction shall be written in three lauguage Hindi, English and Assami on notice board.

M&L in replacement of Cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint complete all as specified and as directed .

Supply and fixing in replacement of Pin type, porcelain, vitreous, white, brown or green insulator including one galvanised mild steel spindle, two galvanised iron washers and one galvanised iron nut, 100 mm height, 65 mm dia for working pressure 1100 volts grade complete all as specified and directed .

Supply and fixing in replacement of Shackle Type, Porcelain, vitreous, white, brown or green insulator including galvanised mild steel straps, washers, insulator bolts, washers and nuts, suitable for 1100 Volts, Height 100 mm, Width 115 mm including galvanised strap 31 x 5 mm, Nut bolts 14 mm and Washer 3 mm thick as under: complete all as specified and directed.

Supply and fixing in replacement of Loop type insulator, vitreous porcelain, white, brown or green, Small size, with overall dimensions 65 x 90mm, clearance of hole 16mm complete all as specified and directed.

M&L for in replacement of Stay assembly 16 mm dia stay rod complete with accessories as shown in electrical plate No. 1 (loop type insulator, stay clamps, excavation and concrete measured separately) complete all as specified and directed . Note : Loop type insulator, excavation, earth work and concrete to be measured and paid against the respective item.

Supply and fixing in replacement of Steel tubulr swaged poles complete with cast iron base plate, finial tapr plug, bolts, nuts and screws as specified type 410 SP-31, 9 metres long complete all as specified and directed.

M&L for in replacement of Galvanised stay strand (Grade 2), size 7/4.0 mm mm complete all as specified and directed.

M&L for in replacement of Cradles, hexagonal/rectangular, fabricated with galvanised steel wire 4mm dia all as site required all as directed.

Labour for re-fixing/ titing/ bending /cradles, hexagonal/ rectangular, fabricated net in proper gap etc all as site to old galvanised wire in any size as safe guard of HT/LT over head line with fixing as directed. Note - The span between two poles is deemed to be considered as one unit.

Re-fixing only with tilting/ jointing/ bending/ jumpering etc all as site to aluminium conductor steel reinforced (ACSR) in any size/ dai/ type etc on existing poles using puller/ rope/ tripod etc to re-staching in permiceable sag all as directed.

Supply and fixing in replacement of Aluminium conductor, steel reinforced complete all as specified and directed .

Supply and fixing in replacement of House service bracket (hook type complete with 3.0m long G.I. pipe 50 mm dia Med. grade, two nos 90 degree bends. M.S. hook and stay or guy complete all as site and directed..

Supply and fixing in replacement of the following cable end/ straight termination jointing kit ,1100 volt grade (earthed) , 3.5 core 400 sqmm aluminium conductor XLPE insulated armoured heavy duty cable heat shinkable suitable in/ out door type to be fix on incoming /outgoing connection of LT panel with gland etc at various location for following size :-. Make - Dension / Raychem / 3M

All as in Item No - 16, but for 3.5 core 185 to 300 Sqmm

All as in Item No - 16, but for 3.5 core 90 to 150 sqmm

All as in Item No - 16, but for 3.5/4 core 25 to 70 Sqmm

All as in Item No - 16, but for 3.5/4 core upto 16 sqmm

Supply and laying or fixing or passing through pipe in replacement of , 1100 volts grade heavy duty cable with PVC insulated Stranded aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 2 core 6 sq. mm nominal cross section in service connections complete all as directed. Make - Finolex /Havells/Polycab

All as in Item No- 21, but for 2core 10 sqmm

All as in Item No- 21, but for 2 core 16 sqmm

Supply and fix MCCB 4 pole, microprocessor based Release range 100 Amps to 250 Amps,415V,AC,50Hz ,36 KA Manual versions With Conforms to IS/IEC 60947-2,Ics=100% Icu,Suitable for Isolation Adjustable Over Load setting: 0.4 - 1.0 x In ,Adjustable Short Circuit setting: 1.5 - 10 x Ir , ,Wide Range of snap fit Internal and External Accessories including Taking down MCCB all as specified and directed by Engineer-in-chargend Make - Seimens/L&T/Schnieder/ABB

All as in Item No- 24, But for MCCB 160 Amps to 400 Amps.

All as in Item No- 24, But for MCCB 250 Amps to 630 Amps, 50KA

Supply and fix MCCB 4 pole, thermal magnetic based Release range 63 Amps to 100 Amps,415V,AC,50Hz ,36 KA Manual versions With Conforms to IS/IEC 60947-2,Ics=100% Icu,Suitable for Isolation Adjustable Over Load setting: 0.8 - 1.0 x In ,Adjustable Short Circuit setting: 1.5 - 10 x Ir , ,Wide Range of snap fit Internal and External Accessories including Taking down MCCB all as specified and directed by Engineer-in-chargend Make - Seimens/L&T/Schnieder/ABB

Supply and Fix 40-63 Amps MCCB, 4 pole, 16 KA "C" series 415 Volt, adjustable overload setting 0.8-1 x In complete all as specified and directed by Engineer-in-chargeand directed by Engr-in-charge . Make : L&T / Indoasian / Havells

Supply and fixing in replacement of MCBs , 240 Volts grade , DP ,"B" curve , 63 Amps complete all as specified and directed by Engr-in-charge. Make :- legrand/ Seimens / schneider

Supply and fixing in replacement of MCBs , 240 Volts grade , DP ,"B" curve , 40 Amps complete all as specified and directed by Engr-in-charge. Make :- legrand/ Seimens / schneider

Supply and fixing in replacement of MCBs , 240 Volts grade , SP, single pole ,"C" curve , 6 to 32 Amps complete all as specified and directed by Engr-in-charge. Make :- legrand/ Seimens / schneider

Supply, fixing and connecting in replacement of Manual On Load change over switch with sheet steel enclosure rating 200 Amps 4 pole, 440 volts grade in sheet metal enclouser conforming to IEC 60947-3, IS/IEC 60947 -3 fixing in panel/ surface of wall on wooden board with making all coonection, gland etc all as site and directed. Make - L&T or equivalent in Siemens/ Phillips/ Havells/ ABB

All as per Item No-32, but for 400 Amps

Supply /laid/ fixing/ connecting and testing in replacement of the following LT under ground XLPE insulated ,armoured heavy duty electric power cable with aluminium conductor , 1100 volts grade (earthed) cross section area 240 Sqmm x 3.5 core. Make - Finolex/ Havells/Polycab

All as in Item No-34, but for 185 Sqmm x 3.5 core

All as in Item No- 34, but for 150 Sqmm x 3.5 core

All as in Item No- 34, but for 120 Sqmm x 3.5 core

All as in Item No- 34, but for 95 Sqmm x 3.5 core

All as in Item No- 34, but for 70 Sqmm x 3.5 core

All as in Item No- 34, but for 50 Sqmm x 3.5 core

All as in Item No- 34, but for 35 Sqmm x 4 core

All as in Item No- 34, but for 25 Sqmm x 4 core

All as in Item No- 34, but for 16 Sqmm x 4 core

All as in Item No- 34, but for 10 Sqmm x 4 core

Excavation in trenches n.exc 1.5 mtr wide and n exc 1.5 mtr in depth and getting out in soft/ loose for laying cables, etc. complete all as specified and as directed.

Returning, filling including spreading, levelling, watering and well ramming in layers n.exc 25 cm in soft/loose soil complete all as specified and as directed.

Removing surplus excavated soil n.exc 50 mtr and depositing where directed at a level n.exc 1.5 mtr above the starting point complete all as specified and as directed..

Supply and laying natural river sand as cushioning of cables, including spreading and punning down all as per clause No 3.21 of SSR part -I complete all as specified and directed by Engineer-in-charge and directed by Engineer in charge Note : punned thickness will only be measured for payment purpose.

M&L for sub class 'B' brick for protection of UG cable in tranches of old size brick all as specified and directed by Engineer-in-charge.

Labour for horizontal boring of Road/path for cable passing through complete all as specified

S & F cable route indicator for LT UG cable of 1100 Volt grade bolted with 40 x 6 mm flat iron member of height 1 Mtr duly painted , embedded, in PCC 1:3:6 type C2 of size 20 x 20 x 30 cm block complete all as specified and directed

M&L for cement concrete type D2, 1:4:8 (using 40 mm graded sto agg.) in foundations, filling and mass concrete complete all as specified.

M&L for cement concrete type C1 1:3:6 (20mm graded aggregate) in or mud stops, rounded or chamfered on edges etc all as specified and directed

M&L for cement concrete type D2, 1:2:4 (using 12.5 mm graded sto agg.) for coping above ground level of steel electric pole concrete complete all as specified.

Supply/ laid/ fixing in replacement of galvanised steel water tube, light grade bore of dia 80 mm with all fittings all as site and directed. Make - Tata / Jindal

Supply/ laid/ fixing in replacement of galvanised steel water tube, light grade bore of dia 50 mm with all fittings all as site and directed. Make - Tata / Jindal

Supply and fix GI pipe of dia 50mm to wall/Pole of medium grade with required clamping arrangements to fix with the pole complete and connecting to the existing pipe line all as specified Make : JINDAL/TATA

M&L for jointing/ cutting/ welding/ replacing hinges etc all as site required to LT panel made out MS sheet and angle for making smoth opening and closing complete with re-painting as same macthing with exsiting surrface all as directed.

M&L for painting to electric pole steel tubular/ PCC after removing /scraping/ bruses/ cleaning to old paint on external surface with two coats of aluminium paint over one coats of red oxide primer on steel tubular and cement paint on PCC poles in any height/ length/ dia etc including cross arms/ angles, nut, bolt , washers etc and making alternate strips of yellow and black paint in 30 cm minium width upto 1.5 Mtr above normal GL and writing Pole No complete all as site and directed by Engr-in-Charge. Note : Colour of paint shall be approved by Engr-in-charge.

All as in Item No- 59, but for two pole structure including all angle iron elements

All as in Item No- 59, but for three pole structure including all angle iron elements

All as in Item No- 59, but for four pole structure including all angle iron elements

Decarbonising/ cleaning of Existing LT panel cubical type of various size consists of bus bar and circuit chamber, metering chambers CTs and relays chambers, checking the bus bar joints, bus bar and circuit spouts, cleaning and applying Busbar Insulation Tape to the bus bars , checking the current transformer, applying Monoplast compound at the bus bar joints after tightening of joints ,replaced new suiable size of lugs /suitable copper control cable and reassembling , if any rusted sheet replaced with new sheet as per existing size complete all as directed by Engineer-in-Charge. Note:- Cost of lubricant/ cleaning agents (CRC & rust remover) / hardware like springs/ bolts/ nuts/ washers,lugs/ suitable copper cables cost of labour, T&P required for replacement shall be etc. shall be deemed to be included in the rate quoted.

Material and labour for painting to LT panel of any size by scrapping and removing oil paint and applying 01 coats of synthetic enamel paint of approved colour by taking due coplete all as specified and directed by Engineer-in-charge .

Material and labour for painting to 100-400 KVA transformer by scrapping and removing oil paint and applying 01 coats of synthetic enamel paint of approved colour by taking due care for HT/LT side supply all as specified and directed by Engineer-in-charge .

M & L for spreading crushed coarse stones aggregate upto 40mm grade suitable for substation yard complete all as specified and directed.

S & F LED indicating Lamps for R, Y, B phases complete including taking down ols U/S lampsall as specified and directed.

M & L Earthing complete with GI earth plate electrode 60cmX60cmX6 mm thick buried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connecting to galvanized earth strip 32 x 6 mm as earthing conductor by means of bolts, nuts, check nuts and washers of GI and all as shown in Electrical plate No.5 of SSR Part I and including testing on completion all as specified locations and as directed by the Engineer-in-Charge. Note: 1.The above quoted rate shall include cost of main earthing lead of 32 x 6mm GI earth strip, charcoal, salt, excavation and earth work in any type of soil CI cover, funnel with 20mm dia light grade GI water pipe including GI protection pipe 40mm dia light grade for earth strip etc. 2. The cost of earth pit is deemed to be included in the unit rate.

Supply and fixing in replacement of Test point terminal block made of gun metal or phosphorus bronze in size 75x75x25 mm drilled and screwed including 03 nos ,8 mm dai 25 mm long hex head screw complete all as specified and directed.

S&F 30 W LED Street light ,IP 66 ,230V environment friendly with operating temperature -10 to 50 degree celsius, operating voltage range 140 to 270 Volts, system lumen > 2500, colour temperature 5700K suitable for pole dia 43mm (max) including taking down old unserviceable security lights complete all as specified and directed. Make- havells/ Crompton/Philips / BAJAJ

S&F 60 W LED Street light,IP 66 ,230V environment friendly with operating temperature -10 to 50 degree celsius, operating voltage range 140 to 270 Volts, system lumen 6500, colour temperature 5700K suitable for pole dia 54mm (max) including taking down old unserviceable security lights complete all as specified and directed. Make- havells/ Crompton/Philips / BAJAJ

S&F 70 W LED floodlight ,IP 66 ,230V environment friendly with operating temperature -10 to 45 degree celsius, operating voltage range 140 to 270 Volts, system lumen >=7000, colour temperature 5700K including taking down old unserviceable security lights complete all as specified and directed. Make- havells/ Crompton/Philips / BAJAJ

S&F 100 W LED Street light ,IP 66 ,230V environment friendly with operating temperature -10 to 50 degree celsius, operating voltage range 140 to 270 Volts, system lumen 4600, colour temperature 5700K suitable for pole dia 43mm (max) including taking down old unserviceable security lights complete all as specified and directed. Make- havells/ Crompton/Philips / BAJAJ

S&F 120 W LED floodlight ,IP 66 ,230V environment friendly with operating temperature -10 to 45 degree celsius, operating voltage range 140 to 270 Volts, system lumen >=7000, colour temperature 5700K including taking down old unserviceable security lights complete all as specified and directed. Make- havells/ Crompton/Philips / BAJAJ

Supply and fixing in replacement of 25W LED outdoor New generation, post-top, energy saving, environmental friendly, long life aesthetically designed with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs as light source with IP 65 protection complete all as specified and directed. Make- Havells model No Coral (Opal)

Supply and fixing in replacement of 8W LED outdoor new generation landscape lighting fitting Bambo type with 1mtr length IP 65 protection including base to stand alone complete all as specified and directed. Make - Havells model No- Bambo 8W or its equivalent in Bajaj / Philips

Supply and fixing in replacement of 8W LED outdoor new generation landscape lighting fitting Cone type with IP 65 protection including base to stand alone complete all as specified and directed. Make - Havells model No- Cone 8W or its equivalent in Bajaj / Philips

Supply and fixing in replacement of LT overhead PVC line spacers as per the existing site requirement complete all as specified and directed.

Trimming /cutting to small tree branches girth not exc 30 cm minimum 2.0 Mtr clearance complete with required cutting tools, ladders, T&P and safety equipments is deemed to be included in the quoted rate all as specified and as directed.

Supply and fixing in replacement of 3 core 1.5 sqmm multistandard PVC insulated flexible copper cable FRLS grade including required PVC Conduit to protect the cable all as specified and directed. MAKE - havelles/RR kabel

Supply and fixing in replacement of PVC pole mounted loop in loop out box 210 x 310 x 116 mm made of impact assistance plastic and heat resistance material including 01 No 06A SP MCB, 04 Nos 100A rating bus bar mounted on insulators and all cable fixed with suitable lugs and suitable Cable Glands complete all as specified and as directed. Note : (a)The rate of Materials for fixing like MS clamps, nuts, bolts & washers are demmed to be included in the unit price . (b) labour for fixing of MS clamps, nuts & bolts shall deemed to be included in unit rates. (c) Unit rate shall include the connection between existing incoming LT cable lines to new junction box . Make for loop in loop out box : Hensel/Sintex , Make for MCB : Havells/L&T

Supply and fixing in replacement of PVC loop in loop out box 139x119x70 mm made of impact assistance plastic and heat resistance material and all cable fixed with appropriate connector including necessary PCC foundation for landscape light complete all as specified and as directed. Note : (a) labour for fixing of nuts & bolts shall deemed to be included in unit rates. (b) Unit rate shall include the connection between existing incoming LT cable lines to new junction box . Make for loop in loop out box : Hensel/Sintex, Make for MCB- Havells/L&T Note 1:-The contract sum shall be arrieved at after deducting amount of schedule of credit from the total quated amount. Note 2-Contractor's supervisor and main worker would wear shirt/T-shirt of colour sky blue/brown/yellow preferable embosed with contractor's firm name while carriying out any activities in defence area for better check of security purpose.

M/S MOHANPASARI

D G Corporation

M/S Deep-Jeet

MAHANTA ENTERPRISES

M/S GOSWAMI ENGINEERING

Chinmay Traders

M/S BHAGWATI CONSTRUCTION CO.

Sibson Constructions And Co

M/s Borah Enterprise