REPAIR TO WOODEN STEEL FURNITURES AND REWEAVING RETAPPING CANNING OF FURNITURE AT MIL STATION DHRANGADHRA

Amount

REPAIR TO Charpoy GI Plytop (32mm) (Drg No FD-220)

Removing unserviceable ply top and S&F new plywood top of size 1980mm x 900mm x 12mm thick BWR grade ISI marked. Top shall be fitted with appropriate sizes of nuts and bolts with washer as specified in Drg and directed.

(a) Removing of damaged/broken long rail from charpoy GI pipe and S&F new long rail made out of GI Pipe 32mm bore (ISI marked) medium grade including threading both sides & fixing in Charpoy all as specified in Drg & directed by Engr-In-Charge.

(b) Removing of old damaged/broken short rail from Charpoy and making of short rail from old u/s long rail (retervied from ser item No 1.02 above) including threading & fixing in charpoy GI Pipe all as specified in Drg & directed by Engr-In-Charge.

(c) Removing of old damaged/broken leg from charpoy and making leg from old u/s short rail (retervied from ser item No 1.03 above) including threading and S&F 6mm MS plate in bottom and 25 x 3mm of MNF clamp (2 Nos each leg) to be welded with legs & fixing in charpoy GI Pipe all as specified in Drg & directed by Engr-In-Charge.

(d) Removing of old broken/damaged check nuts and S&F new check nuts of 32 mm dia heavy duty to Charpoy GI pipe all as specified in Drg & directed by Engr-In-Charge

(e) Removing old broken/damaged GI elbow, 3 way, 32 mm bore and S&F new GI elbow, 3 way, 32mm bore (ISI marked) to Charpoy GI pipe all as specified in Drg & directed by Engr-In-Charge.

(f) Removing damed/broken welding supports from charpoy GI pipe 32mm and S&F new welding support of 40 x 6 mm flat iron, 850mm long including applying two coats of silver enamel paint over one coat of red oxide primer

Repair to Bed Hard Steel (FD/MAP-II/08®)

(a) M&L for removal of u/s plywood of bed in any position, S&F new plywood 12mm thick, BWR grade, ISI marked including fixing with suitable size screw & cup washer in position all as shown on drg and specified.

(b) M&L for retightning of loose components of bed including welding where ever required on joints, replacement of old nuts & bolts where ever required and touching up on welded points with synthetic enamel paint of same colour/shade all as shown on Drg & directed.

(c) M&L for removal of prelaminated particle board Headrest of Bed, and, S&F new 18mm thick prelaminated particle board exterior grade mallamine faced veneered both side decorated (ISI Marked) with 4mm thick teak wood beading of suitable size including fixing in position with screws & washers, complete all as shown on drg and directed.

(d) M&L for removal of prelaminated particle board Footrest of Bed, and, S&F new 18mm thick prelaminated particle board exterior grade mallamine faced veneered both side decorated (ISI Marked) with 4mm thick teak wood beading of suitable size including fixing in position with screws & washers, complete all as shown on drg and directed.

Repair to Charpoy IP Hard Top FD/MAP-II/01

(a) Removing of old/unsv ply wood from charpoy and S&F new 12mm thick plywood, BWR grade, ISI marked to the top of charpoy IP of appropriate size including fixing to charpoy using nuts, bolts and washers as shown on drg complete all as specified in drg and directed.

(b) M&L for preparation of old painted steel surfaces by scraping/rubbing with sand paper and filling depressions with putty where ever required and applying one coat of synthetic enamel paint of approved shade complete all as specified in drg and directed.

Repair to Charpoy IP folding (FD-388 & FD-388®)

(a) Removing of old unserviceable charpoy top and S&F new top of 8-9 mm thick plywood BWR grade (ISI Marked) with appropriate size nuts, bolts & washer including tightening the loose components complete all as specified in drg and directed.

(b) Removing of old unserviceable members of charpoy folding and S&F new members of 25mm dia 2 mm thick MS conduite fixed with gas welding as specified & shown in drg.

(c) M&L for preparation of old painted steel surfaces by scraping/rubbing with sand paper and filling depressions with putty where ever required and applying one coat of synthetic enamel paint of approved shade complete all as specified in drg and directed.

REPAIR TO Chairs, Bin Soiled Linen etc (Drg Nos FD-203, 226, 202, 256, 279, 250, 280, 244, 70(M), 229 & 204)

Re-caning of Chairs, Bin Soiled Linen etc (except Chair Verandah) with 2mm wide & 0.4mm thick half round plastic cane except border which shall be 3.5mm(Minimum) wide & 0.6mm thick, flat super quality cream/ white colour and weaving in accordance to Godrej Pattern as shown on drawing FD-03(M) Sheet 1/1 including removing unserviceable plastic cane all as specified and directed.

REPAIR TO Chair Verandah (Drg No FD-19(M), FD-256, FD-359)

(a) Re-caning of Chair Verandah with 4mm wide & 0.4mm thick half round plastic cane except border which shall be 5mm wide & 0.6mm thick flat super quality cream/ white colour including applying one coat of synthetic enamel paint White after preparation of surface to complete frame of chair all as specified and directed.

(b) Repairs to broken mild steel components of chair verandah with gas welding.

(c) Removing old broken leg of chair verandah and providing new 20mm dia MS pipe 1.6mm thick complete with welding.

(b) S&F, PVC rubber Shoe/Toe of best quality to the legs of chairs after removing the old un- serviceable shoes all as specified and directed.

REPAIR TO TABLE DINING OR'S STEEL WITH ALUMINUM TOP (Drg No FD-165)

(a) Removing existing unserviceable table top and S&F, new table top made from block board, grade 2 quality, interior grade, commercial type, 19mm thick, size 1910x 680mm duly covered with anodised aluminum sheet 22 gauge thick and fixed with screws to MS pipe frame all as shown in drawing and directed.

(b) Gas welding to broken joints/spots of 25mm x 25mm square pipe frame all around.

(c) Cutting of worn out/damaged legs of table and replaced with new MS square pipe piece 3" to 4" long including welding complete.

(d) Painting to MS frame of table dining with one coat of black synthetic enamel paint including preparation of surfaces complete all as specified and as directed.

(e) Removing unserviceable hard rubber shoe from legs of table and S&F, new hard rubber shoes.

REPAIR TO Almirah Large Steel (Drg No FD-67(M) &1031)

(a) M&L for one coat of synthetic enamal paint OG to internal /external surface & shelves completely after preparation of old painted surfaces by applying sand paper and filling with putty where ever required to Almirah Large steel all as specified & directed by Engineer-in-charge.

(b) Removing of old broken/unserviceabble shelves from Almirah large steel and S&F new shelves made out of 1mm thick MS sheet bent to shape required all as specified in drg & directed by Engr-in-charge.

(c) Removing broken/ dacayed legs from exsiting Almirah Large steel and S&F new legs made out 1.00 mm thick MS sheet bend to shape all as specified in drg and directed by Engr-In-Charge

(d) Removing of old unserviceable locking device three way from exsiting Almirah Large steel and S&F new locking device made out of 10 mm dia MS bar round and 3 mm MS plate all as specified in drg and directed by Engr-In-Charge

REPAIR TO Almirah Med Steel (Drg No FD-1032)

(a) M&L for one coat of synthetic enamal paint OG to internal/external surface & shelves completely after preparation of old painted surfaces by applying sand paper and filling with putty where ever required to Almirah Medium steel all as specified & directed by Engineer-in-charge.

(b) Removing of old broken/ unserviceabble shelves from Almirah Medium steel and S&F new shelves made out of 1mm thick MS sheet bent to shape required all as specified in drg & directed by Engr-in-charge.

(c) Removing broken/ dacayed legs from exsiting Almirah medium steel and S&F new legs made out 1.00 mm thick MS sheet bend to shape all as specified in drg and directed by Engr-In-Charge

(d) Removing of old unserviceable locking device three way from exsiting Almirah Medium steel and S&F new locking device made out of 10 mm dia MS bar round and 3 mm MS plate all as specified in drg and directed by Engr-In-Charge

(e) Removing of broken/unserviceable handle from existing almirah large/medium and S&F new Chromium Plated steel handle 100mm long all as specified in drg & directed by Engr-in-Charge.

(f) Removing of old unserviceable lock from exsiting almirah Large/Med steel (Drg No FD-67(M), 1031 & 1032) and S&F new four lever lock with duplicate keys all as specified in drg & directed by Engr-charge.

(g) Removing of old/broken cleats from existing Almirah large/medium steel with shelves (Drg No FD-67(M), 1031 & 1032) and S&F new cleats made out of 1.6 mm thick PBI sheet bend to shape and shall be fixed with nut & bolt to give support to shelves all as specified in drg & directed by Engr-in-Charge.

REPAIR TO Teapoy Varandah (Drg No FD-35(M), FD- 295, D-255, FD-383)

(a) Spot welding to broken joints of MS member of teapoy verandah all as specified and directed

(b) Removing old u/s tops from Teapoy varandah and S&F new top made out of 18mm thick pre-laminated particle board exterior grade type II (ISI marked) one side teak face & other side white with PVC beading all around all as specified in drg & as directed by Engr-in-charge.

(c) M&L for one coat of synthetic enamal white paint to Teapoy Varandah after preparation of old painted surfaces by applying sand paper and filling with putty where ever required all as specified & directed by Engr-in-charge.

REPAIRS TO CHAIR TUBULAR STEEL WITH OR WITHOUT ARMS (Drg No FD-75(M))

(a) Gas welding to broken members of chair tubular steel with & without arms as directed

(b) Painting of MS members of chair tubular steel with arms with one coat of olive green synthetic enamel paint all as specified and directed.

(c) Painting of MS members of chair tubular steel without arms with one coat of olive green synthetic enamel paint all as specified and directed.

(d) Dismantling of unserviceable seat of chair tubular steel with arms and without arms, S&F new seat made out of Ist class hard wood frame of size 18"x16" and 18"x18", fixing to chair with 75 x 6mm GI nut and bolt, including canning with 2mm plastic cane white half round and 4 mm plastic cane for border all as per drawing .

(e) Dismantling to unserviceable back of chair tubular steel with arms and without arms, S&F of new back made out of Ist class hard wood frame of size 16"x16" and 18"x15", fixing to chair with 75 x6mm GI nut & bolt, including canning with 2mm plastic cane white half round and 4 mm plastic cane for border all as per drawing .

(f) S&F of plastic cap 19mm dia to plug the open end of pipe of chair as shown in drawing .

(g) Dismantling of unserviceable hand rest and S&F new hand rest made out of Ist class hard wood duly painted with black colour complete all as shown in drawing and directed

REPAIR TO Table Office Clerk Steel (Drg No FD-84(M) & 1004)

(a) M&L for one coat of synthetic enamal paint OG to all steel Surface after preparation of old painted surfaces by applying sand paper and filling with putty where ever required to Table office clk steel all as specified & directed by Engineer-in-charge.

(b) Removing of unserviceable drawers from existing table office clk steel and S&F, new drawers made out 1 mm thick MS sheet all as specified in drg & directed by Engr-in-charge.

(c) Removing old u/s tops from Table office clk steel and S&F new top made out of 18mm thick pre-laminated particle board exterior grade type II (ISI marked) one side teak face & other side white with PVC beading all around, all as specified in drg & as directed by Engr-in-charge.

(d) Removing of old unserviceable lock from exsiting table office clk steel and S&F new four lever lock with duplicate keys.

REPAIR TO Table Office Officer Steel (Drg No FD-84(M) & 1003)

(a) M&L for one coat of synthetic enamal paint OG to all steel Surface after preparation of old painted surfaces by applying sand paper and filling with putty where ever required to Table office Officer steel all as specified & directed by Engineer-in-charge.

(b) Removing of unserviceable drawers from existing table office Officer steel and S&F new drawers made out 1 mm thick MS sheet all as specified in drg & directed by Engr-in-charge.

(c) Removing old u/s tops from Table office Officer steel and S&F new top made out of 18mm thick pre-laminated particle board exterior grade type II (ISI marked) one side teak face & other side white with PVC beading all around, all as specified in drg & as directed by Engr-in-charge.

(d) Removing of old unserviceable lock from exsiting table office Officer steel and S&F new four lever lock with duplicate keys.

(e) Gas welding to broken joints of table office Officer/Clk steel

REPAIR TO TABLE 900MM X 600MM X 760MM WITH DRAWER/WITHOUT DRAWER STEEL (Drg No FD-1008 & FD-1007 )

(a) Taking down unserviceable table top and providing new top of 18 mm thick prelaminated particle board, interior grade, solid core with melamine face on one side and balancing white on other side including 4 mm thick teak wood edging all around complete all as shown on drawing.

(b) Gas welding to broken joints of table Steel.

(c) Removing of unserviceable locks of drawer and supply & fixing new four lever locks with key in duplicate all as specified in drawing.

(d) Repairs to the drawer of table steel by making good dents, proper alignment for smooth function of drawer and preparation of old surfaces, inside and outside of drawer and legs & applying one coat of olive green paint by spraying.

REPAIR TO Chair Dinning (Drg No. FD-203, 226, 353, 354, 279 & FD/MAP-II/05

(a) M&L for removing of old broken rear leg of chair dinning and S&F new rear leg made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg.

(b) M&L for removing of old broken front leg of chair dinning and S&F new front leg made out of first class hard wood (teak wood) of similar size & shape complete as specified & shown in drg.

(c) M&L for removing of old broken stifner of chair dinning and S&F new stifner made out of first class hard wood (teak wood) of similar size & shape complete as specified & shown in drg.

(d) M&L for removing of old broken front/side/rear rail of chair dinning and S&F new front/side/rear rail made out of first class hard wood (teak wood) of similar size & shape including drilling holes for caning all as specified & shown in drg.

(e) M&L for removing of old broken back rest of chair dinning and S&F new back rest made out of first class hard wood (teak wood) of similar size & shape all as specified & shown in drg

Removing old/unserviceable PVC seat from chair and S&F new PVC seat 4 mm thick and fixing with suitable screws as specified on drg & directed.

(g) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of chair dining all as directed by Engineer-in-charge

REPAIR TO Chair Easy (Drg No. FD-229, 17M, 201)

(a) M&L for removing of old broken rear leg of chair easy and S&F new rear leg made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg.

(b) M&L for removing of old broken front leg of chair easy and S&F new front leg made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg.

(c) M&L for removing of old broken front/side/rear rail of chair easy and S&F new front/side/rear rail made out of first class hard wood (teak wood) of similar size & shape including drilling holes for caning all as specified & shown in drg.

(d) M&L for removing of old broken top/bottom/side rail of back rest of chair easy and S&F new top/bottom/side rail made out of first class hard wood (teak wood) of similar size & shape including drilling holes for caning all as specified & shown in drg.

(e) M&L for removing of old broken arms of chair easy and S&F new arm made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg.

(f) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of chair easy all as directed by Engineer-in-charge.

REPAIR TO Chair Writing (Drg No. FD-280, 20M, 202, 250)

(a) M&L for removing of old broken rear leg of chair writing and S&F new rear leg made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg.

(b) M&L for removing of old broken front leg of chair writing and S&F new front leg made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg.

(c) M&L for removing of old broken stifner of chair writing and S&F new stifner made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg.

(d) M&L for removing of old broken front/side/rear rail of chair writing and S&F new front/side/rear rail made out of first class hard wood (teak wood) of similar size & shape including drilling holes for caning all as specified & shown in drg.

(e) M&L for removing of old broken arms of chair writing and S&F new arm made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg.

(f) M&L for removing of old broken back rest of chair writing and S&F new back rest made out of first class hard wood (teak wood) of similar size & shape all as specified & shown in drg

(g) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of chair writting all as directed by Engineer-in-charge.

REPAIR TO Teapoy Wooden (Drg No. FD-382, 232, 34M, 278)

(a) M&L for removing old unservicable top and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side with 4 mm thick teak wood edging alround all as specified & shown in drg.

(b) M&L for removing of old unservicable legs and S&F, new teak wood legs duly finished/smoothened complete all as specified & shown in drg.

(c) M&L for removing of old unservicable front/rear rails, and S&F, new teak wood rail duly finished/smoothened complete all as specified & shown in drg.

(d) M&L for removing of old unservicable bottom rails and S&F, new teak wood rail duly finished/smoothened complete all as specified & shown in drg.

(e) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of teapoy all as directed by Engineer-in-charge

REPAIR TO TABLE 900 MM x 600 MM x 760 (WITH/WITHOUT DRAWER) (Drg No. FD-41, 42(M) & 224, FD-228,279, 16M, 203,55, 223 & 284)

(a) M&L for removing old unservicable top and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side with 4 mm thick teak wood edging alround all as specified & shown in drg.

(b) M&L for removing of old unservicable legs and S&F, new teak wood legs duly finished/smoothened complete all as specified & shown in drg.

(c) M&L for removing of old unservicable long rail and S&F, new teak wood long rail duly finished/smoothened complete all as specified & shown in drg.

(d) M&L for removing of old unservicable short rail and S&F, new teak wood short rail duly finished/smoothened complete all as specified & shown in drg.

(e) M&L for removing of old unservicable middle stiffener and S&F, new teak wood middle stiffener duly finished/smoothened complete all as specified & shown in drg.

(f) M&L for removing of old unservicable side stiffener and S&F, new teak wood side stiffener duly finished/smoothened complete all as specified & shown in drg.

(g) M&L for removing of old unservicable drawer and S&F, new drawer made out of Ist class hard wood and 6mm thick ply wood for bottom of drawer complete all as specified & shown in drg.

(h) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of table all as directed by Engineer-in-charge

REPAIR TO SOFA SET (Drg No. FD-281, FD-373)

(a) M&L for removing old unservicable arms of sofa set single or 3 seat and S&F, new arms of sofa set single or 3 seat made out of 1st class hard wood (Teak wood) of size and pattern all as shown on drawing.

(b) M&L for removing old unserviceable leg of sofa set single or 3 seat and S&F, new leg of sofa set single or 3 seat made out of 1st class hard wood (Teak wood) of size and pattern all as shown on drawing.

(c) M&L for removing old unservicable cushion of sofa set and S&F, new cushion of 100mm thick foam, 40 density, size 530mm x 500mm for seat and back of Sofa Set 4/5 Seater, covered with superior quality tapestry cloth including stitching in size etc complete all as shown on drawing and as directed.

M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of sofa set 4 seater all as directed by Engineer-in-charge.

M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of sofa set 5 seater all as directed by Engineer-in-charge.

REPAIR TO Table writing (Drg No. FD-33, 249, 275)

(a) M&L for removing old unservicable top and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side with 4 mm thick teak wood edging alround all as specified & shown in drg.

(b) M&L for removing old unservicable front side of drawer and S&F, new front side of drawer made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side including providing new chromium plated 35mm size knob complete all as specified and shown on drawing.

(c) M&L for removing old unservicable bottom of drawer and S&F, new bottom of drawer made out of 6mm thick, commercial ply wood complete all as specified and shown on drawing.

(d) M&L for removing old unservicable door and S&F, new door made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side with 4 mm thick teak wood edging alround including fixing with hinges and providing new chromium plated 35mm size knob all as specified & shown in drg.

(e) M&L for removing old unservicable back of table writing and S&F, new back of table writing made out of 6mm thick, commercial, BWR grade ply wood complete all as specified and shown on drawing.

(f) M&L for removing old unservicable side of table writing and S&F, new side of table writing made out of 6mm thick, commercial, BWR grade ply wood complete all as specified and shown on drawing.

(g) M&L for removing old unservicable legs and S&F, new teak wood leg duly finished/smoothened complete all as specified and shown on drawing.

(h) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of table writing all as directed by Engineer-in-charge.

REPAIR TO Table 900 x 900 x 760 mm (Drg No. FD-288, 88M & 291)

(a) M&L for removing old unservicable top and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side with 4 mm thick teak wood edging alround all as specified & shown in drg.

(b) M&L for removing of old unservicable rails and S&F, new teak wood rail duly finished/smoothened complete all as specified & shown in drg.

(c) M&L for removing of old unservicable legs and S&F, new teak wood legs duly finished/smoothened complete all as specified & shown in drg.

(d) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of table all as directed by Engineer-in-charge.

REPAIR TO TABLE DINING 6 PERSONS (Drg No. FD-238, 239 & 273, FD/E6/MAP-II/03)

(a) M&L for removing old unservicable top and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side with 4 mm thick teak wood edging alround all as specified & shown in drg.

(b) M&L for removing of old unservicable long rails and S&F, new teak wood long rail duly finished/smoothened complete all as specified & shown in drg.

(c) M&L for removing of old unservicable top side rails and S&F, new teak wood top side rail duly finished/smoothened complete all as specified & shown in drg.

(d) M&L for removing of old unservicable top side short rails and S&F, new teak wood top side short rail duly finished/smoothened complete all as specified & shown in drg.

(e) M&L for removing of old unservicable legs and S&F, new teak wood legs duly finished/smoothened complete all as specified & shown in drg.

(f) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of table all as directed by Engineer-in-charge.

REPAIR TO SIDE BOARD (Drg No. FD-371 & 372)

(a) M&L for removing old unservicable double leaf door and S&F, new double leaf door made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side including providing new butt hinges and new chromium plated 35mm size knob complete all as specified and shown on drawing.

(b) M&L for removing old unservicable front side of drawer and S&F, new front side of drawer made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side including providing new chromium plated 35mm size knob complete all as specified and shown on drawing.

(c) M&L for removing old unservicable bottom of drawer and S&F, new bottom of drawer made out of 6mm thick, commercial ply wood complete all as specified and shown on drawing.

(d) M&L for removing of old unservicable side & rear rails and S&F, new teak wood side & rear rail duly finished/smoothened complete all as specified & shown in drg.

(e) M&L for removing old unservicable back of side board and S&F, new back of side board made out of 6mm thick, commercial, BWR grade ply wood complete all as specified and shown on drawing.

(f) M&L for removing old unservicable top of side board and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side complete all as specified & shown in drg.

(g) M&L for removing old unservicable side of side board and S&F, new back of side of side board made out of 6mm thick, commercial, BWR grade ply wood complete all as specified and shown on drawing.

(h) M&L for removing of old unservicable legs and S&F, new teak wood legs duly finished/smoothened complete all as specified & shown in drg.

(j) M&L for removing of old unservicable cromium plated knob of side board and S&F, new cromium plated knob all as specified & shown in drg.

(k) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of side board all as directed by Engineer-in-charge.

REPAIR TO Peg Table (Drg No. FD-266, FD-277, FD-384, 25M)

(a) M&L for removing old unservicable top and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side with 4 mm thick teak wood edging alround all as specified & shown in drg.

(b) M&L for removing of old unservicable legs and S&F, new teak wood legs duly finished/smoothened complete all as specified & shown in drg.

(c) M&L for removing of old unservicable front & rear rail and S&F, new leg made out of 1st class hard wood teak duly finished/ smoothened complete all as specified & shown in drg.

(d) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of peg table all as directed by Engineer-in-charge.

REPAIR TO TABLE CENTRE (Drg No. FD-29, 235,274)

(a) M&L for removing old unservicable top and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side with 4 mm thick teak wood edging alround all as specified & shown in drg.

(b) M&L for removing of old unservicable legs and S&F, new teak wood legs duly finished/smoothened complete all as specified & shown in drg.

(c) M&L for removing of old unservicable top long rails and S&F, new teak wood top long rail duly finished/smoothened complete all as specified & shown in drg.

(d) M&L for removing of old unservicable top short rails and S&F, new teak wood top short rail duly finished/smoothened complete all as specified & shown in drg.

(e) M&L for removing of old unservicable side stiffener and S&F, new teak wood side stiffener duly finished/smoothened complete all as specified & shown in drg.

(f) M&L for removing of old unservicable middle stiffener and S&F, new teak wood middle stiffener duly finished/smoothened complete all as specified & shown in drg.

(g) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of center table all as directed by Engineer-in-charge.

REPAIR TO TABLE DRESSING LADIES WITH MIRROR (Drg No. FD-235, 251 & 274, FD/E6/MAP-II/07)

(a) M&L for removing old unservicable top and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side complete all as specified & shown in drg.

(b) M&L for removing old unservicable back of table and S&F, new back of table made out of 12mm thick, commercial, BWR grade ply wood complete all as specified and shown on drawing.

(c) M&L for removing old unservicable side and partition and S&F, new side and partition made out of prelaminated particle board 12mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side complete all as specified & shown in drg.

(d) M&L for removing old unservicable bottom ply wood of drawers of table and S&F, new bottom ply wood of drawers of table made out of 6mm thick, commercial, BWR grade ply wood complete all as specified and shown on drawing.

(e) M&L for removing old looking mirror of table and S&F, new looking mirror of 5.5mm thick with teak wood frame and with 6mm thick, commercial, BWR grade ply wood at back complete all as specified and shown on drawing.

(f) M&L for removing old unservicable aluminum channel and S&F, new aluminum channel having two 'U' shaped channels for sliding of plain glass of 5mm thick complete all as specified & shown in drg.

(g) M&L for removing old unservicable/broken sliding glass shutter and S&F, new plain, sliding glass, 5mm thick shutter complete all as specified and as shown in drawing .

(h) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of table dressing ladies all as directed by Engineer-in-charge.

REPAIR TO TABLE DRESSING GENTS WITH MIRROR (Drg No. FD-230, 31M FD/E6/MAP/16)

(a) M&L for removing old unservicable back side of the box of table and S&F, new back side of the box of table made out of 12mm thick, teak wood planks in one piece, complete all as specified and shown on drawing.

(b) M&L for removing old unservicable top of the box of table and S&F, new top of the box of table made out of prelaminated particle board 12mm thick exterior grade (ISI marked), with one side teak face and balancing white on other side complete all as specified & shown in drg.

(c) M&L for removing old unservicable bottom of the box of table and S&F, new bottom of the box of table made out of prelaminated particle board 12mm thick exterior grade (ISI marked), with one side teak face and balancing white on other side complete all as specified & shown in drg.

(d) M&L for removing old unservicable side and partition and S&F, new side and partition made out of prelaminated particle board 12mm thick exterior grade (ISI marked), with one side teak face and balancing white on other side complete all as specified & shown in drg.

(e) M&L for removing old looking mirror of table and S&F, new looking mirror of 5.5mm thick with teak wood frame and with 6mm thick, commercial, BWR grade ply wood at back complete all as specified and shown on drawing.

(f) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of table dressing gents all as directed by Engineer-in-charge.

REPAIR TO TABLE BED SIDE (Drg No. FD/E6/MAP/15(R)

(a) M&L for removing damaged/broken MS square pipe and S&F, new MS 18mm size square pipe of 18 Gauge thick, length n.exc 600mm each part for various parts of table bed side duly painted with two coat of synthetic enamel paint (approved colour) over one coat of red oxide primer all as shown on drg & as directed.

(b) M&L for removing damaged/broken handles of drawers and S&F new handles for drawer 75mm long mild steel chromium plated all as per drg & as directed

(c) M&L for removing damaged/broken sides and S&F new sides with 18mm thick Pre laminated particle board exterior grade mellamine faced veneered both side decorated (ISI Marked) all as per drawing & as directed.

(d) M&L for removing damaged/broken top and S&F new top with 18mm thick Pre laminated particle board exterior grade mellamine faced veneered both side decorative (ISI Marked) with 4 mm teak wood edging with polished all as per drg & directed.

(e) M&L for removing damaged/broken drawers and S&F new drawer all as per drg & directed.

(f) M&L for removing damaged/broken shoe and S&F new PVC/Rubber shoe all as per drg & directed.

(g) M&L for preparation of surfaces by cleaning with emery paper and apply one coat of synthetic enamel black paint over a coat of primer to frame of table bed side complete all as directed.

REPAIR TO HAT STAND WITH MIRROR (Drg No. FD-23M, 223 & 361)

(a) M&L for removing old looking mirror of table and S&F, new looking mirror of 5.5mm thick with teak wood frame and with 6mm thick, commercial, BWR grade ply wood at back complete all as specified and shown on drawing.

(b) M&L for removing broken aluminium hooks, solid body 125mm and S&F new aluminium hooks, solid body 125mm for Hat Stand all as specified and shown on drawing.

(c) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of Hat Stand Small side all as directed by Engineer-in-charge.

REPAIR TO TABLE 900 MM x 900 MM x 760 MM STEEL (Drg No. FD-121M)

(a) M&L for removing old unservicable top and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side with 4 mm thick teak wood edging alround all as specified & shown in drg.

(b) Gas welding to broken joints of table steel.

(c) Cutting of worn out portion of legs of table and providing new 25x25mm square pipe of 1.6mm thick piece of 3” to 4” long including gas welding complete.

(d) Preparation of old painted surface and applying one coat of black synthetic enamel paint complete all as specified and directed.

REPAIR TO TABLE DINING 8 PERSONS (Drg No. FD-238, 239 & 273, FD/E6/MAP-II/03)

(a) M&L for removing old unservicable top and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side with 4 mm thick teak wood edging alround all as specified & shown in drg.

(b) M&L for removing of old unservicable long rails and S&F, new teak wood long rail duly finished/smoothened complete all as specified & shown in drg.

(c) M&L for removing of old unservicable top side rails and S&F, new teak wood top side rail duly finished/smoothened complete all as specified & shown in drg.

(d) M&L for removing of old unservicable top side short rails and S&F, new teak wood top side short rail duly finished/smoothened complete all as specified & shown in drg.

(e) M&L for removing of old unservicable legs and S&F, new teak wood legs duly finished/smoothened complete all as specified & shown in drg.

(f) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of table all as directed by Engineer-in-charge.

REPAIR TO CHAIR DINING WITH CUSHION (Drg No. FD/E6/MAP-II/04

(a) M&L for removing of old broken rear leg of chair dining and S&F new rear leg made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg.

(b) M&L for removing of old broken front leg of chair dining and S&F new front leg made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg.

(c) M&L for removing of old broken stifner of chair dining and S&F new front leg made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg.

(d) M&L for removing of old broken front/side/rear rail of chair dining and S&F new front/side/rear rail made out of first class hard wood (teak wood) of similar size & shape including drilling holes for caning all as specified & shown in drg.

(e) M&L for removing of old broken back rest of chair dinning and S&F new back rest made out of first class hard wood (teak wood) of similar size & shape all as specified & shown in drg

(f) M&L for removing of old unserviceable seat of chair dining and S&F new seat made out of 75mm thick, 40 density, U-foam covered with superior quality of tapestry cloth including stiching/fixing all as specified and directed.

(g) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of chair dining all as directed by Engineer-in-charge

REPAIR TO CHAIR REVOLVING & CHAIR COMPUTER (TP & FD/E6/MAP/01)

(a) Removing the existing U/S Foam & tapestry of seat and S&F new 40 density foam cushion 3" with teapastry all as specifed & shown on drg.

(b) Removing the existing U/S Foam & tapestry of back and S&F new 40 density foam cushion 3" with teapastry all as specified & shown on drg.

(c ) Removing the existing U/S arms and fixing of new arms all as specified & shown on drg.

(d) Removing the existing U/S hydrolic from chair computer and fixing of new hydrolic all as specified & shown on drg.

(e) Removing the existing U/S caster wheel of chair computer and fixing of new caster wheel all as specified & shown on drg.

(f) Removing the existing U/S base from chair computer and fixing of new base all as specified & shown on drg.

Repair to Chair writing with cushion seat & Back FD/MAP-12

(a) Taking out unserviceable seat and S&F new seat made of 12mm thick hot pressed ply wood upholstered with fabric and mounlded polyurethane foam with PVC lipping all round. The polyrethane foam shall be 50mm thick and 5shall be moulded with density 50-55 KG per Cum complete all as shown on drg.

(b) All as item No 35.01 above but old/unservicialble back complete all as shown on drg & as directed..

(c ) Taking out old broken/unserviciable arm rest of chair writing and S&F new one piece arm rest made of black integral skin polyurethane with 75-85 Shore 'A' hardness and reinforced with MS insert, it shall be scratch and weather resistant all as shown on drg.

(d) Preparation of old painted surface by scraping, rubbing & applying one coat of synthetic enamel paint (black) to MS tubular frame of Chair writing complete all as specified and directed.

(e) Taking out unserviceable/broken frame and S&F new frame cantilever type powder coated MS tubular frame made of 25mm x 10mm all as per drg complete all as directed.

motwani and associate

S t modi

M/S Super Steel Works