SPECIAL REPAIR TO BLDG NO P-31 SNOW VIEW LINE AT PALAMPUR MIL STN

Amount

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thick above or below ground level complete and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m complete all as specified and directed.

Taking down cement plaster including backing etc from brick/stone walls / concrete surfaces including raking out joints, hacking for key , scrubbing down with water etc complete all as specified and directed

Taking down chowkats with shutters (without taking off shutters from chowkat) not exceeding 1.50 Sqm each complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutters from chowkat) exc 1.50 Sqm but not exc 4.00 Sqm each complete all as specified and directed. .

Taking down steel water tubing 15 mm bore including all fitting and connections complete all as specified and directed.

Taking down steel water tubing 20 mm bore including all fitting and connections complete all as specified and directed..

Dismantling water storage tank of capacity exc 250 ltr but n.exc 500 ltr complete all as specified and directed.

PCC 1:3:6 (nominal mix) type C-1 (using 20mm graded crushed stone aggregates) as in hold fast block and similar work including use and waste of necessary form work complete all as specified and directed.

PCC 1:2:4 (nominal mix) type B-2 (using 40mm graded crushed stone aggregates) as in surface channel and drains complete all as specified and directed.

Cement Concrete M-15, type B1 using 20 mm graded aggregate as in roof kerbs, mud stoppers rounded or chamfered on edegs, padding concrete etc and cutting grooves 10mm wide and 25 mm deep filled with bitumen of grade 85/25 , complete all as specified & directed.

Anodised aluminium frame powder coated for doors, windows, ventilators with one or more rebates including joining cleat for fixing of glass, particle board,aluminium frame etc complete all as specified and directed.

Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain coloured PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 160 of MES SSR 2010 Part-II

Pressed steel frame using 1.25 mm thick PBI sheet (size of frame 105 x 60 mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock/ strike plate etc and filling with PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in back of chowkats complete all as specified.

Pressed steel frame using 1.25 mm thick PBI sheet (size of frame 125 x 60 mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock/ strike plate etc and filling with PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in back of chowkats complete all as specified.

35mm thick second class hardwood (Sal/Hollock) factory made plain framed panelled shutter (two panel) with lock rails & panel of 9 mm B.W.P commercial ply wood or 12 mm thick veneered particle board with commercial veneering on both side. The size of rail and stile as per IS:1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified and directed.

35 mm thick 2nd class hard wood (Sal/Hollock)) glazed & skeleton factory made shutters, open rebated and prepared to receive glass, gauze etc (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass, etc, sizes of members of door shutters as specified in SSR- 2009 Part-I Section 8.24(a) complete all as specified and directed.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of 5 mm thick plain coloured PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site, Sheet No 1/1) specified and directed.

Anodised aluminium window and ventilator sliding shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed.

Framed work such as grills, gratings etc with ends of bars shouldered and/or riveted or forged into spikes framed guard bars including cutting, drilling, welding etc confirming to Fe-290 Gde E-165 all as specified and directed.

300mm long aluminium alloy, anodized, sliding door bolt with hasp, staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

Aluminium handles cast type anodized of size 150 mm complete all as specified and directed.

Ist class hard wood small fittings such as brackets of any type, latch and hinges blocks, shaped door and window stops and the like, including all necessary labours, articles n.exc 200 cucm each complete all as specified and directed.

Aluminium anodized barrel tower bolt of extruded section of size 150 mm and fixed complete all as specified and directed.

300 mm long mild steel ordinary rat tail rod pattern spring including roller and roller plate complete .

Mild steel butt hinges of size 100 mm medium weight cold rolled complete all as specified and directed.

Galvanished mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanished wire staples complete all as specified and directed.

Sheet glass, 5.5mm thick ordinary quality and glazing with oil putty in squares exceeding 0.5 sqm each pane complete all as specified and directed.

Mild steel work as in hold fast, wind ties for roof including securing bolts including all necessary drilling ,bolting or reverting etc and all similar work conforming to Fe-290 (Gde E-165) complete all as specified and directed.

Plain cement concrete M-10, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 50mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).

Demolition of existing concrete/ PCC tiles on roof slab, taking down cement plaster including existing tarfelt from roof, of old roof surfaces by brushing with wire brushes from removing caked etc sweeping with brooms and finally fanning the cleaned surface to remove all loose dit etc on roof and applying the followings:- FIRST COURSE- One coat of bitumen primer conforming to IS- 3384@ 0.40 kg/sqm SECOND COURSE- One coat of bonding material using blown type bitumen conforming to IS- 702 grade 85/25 @ 1.20 kg/sqm THIRD COURSE- A layer of APP modified polymeric membrane, centre core of 100 mm micron HMHDPE, outer film 20 micron each, thickness 3 mm , having weight 2.25 kg/sqm , complete all as specified & directed. FORTH COURSE- One coat of bonding material using blown type bitumen conforming to IS-702 grade 85/25 2 1.20 kg/sqm.

25 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregates) as in floor finish, surface finished even and fair to receive top finish complete all as specified and directed.

Mat finish, premium quality, joint free (edge cut), coloured/ printed ceramic tiles 10 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, as in floors etc. set and jointed in neat cement slurry and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement pointed in white or coloured cement to match complete all as specified and directed.

Glazed ceramic coloured tiles of size 450 mm x 350 mm x 7 mm/350 mm x 250 mm x 7 mm thick as in vertical surfaces , set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tile over and including 10 mm thick cement screed in cement mortar 1:3 complete all as specified and directed. Size/Shade/Colour of tile shall be approved by the GE.

Machine cut kota stone slab flooring 18-20 mm thick of size not less than 550 mm X 550 mm as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, as in floor etc, laid over and including 15mm screed layer in cement mortar 1:4 (1 cement : 4 coarse sand), cutting, rubbing, grinding and polishing to achieve mirror finish, laid over PCC subbase complete, all as specified.

Machine cut kota stone slab 20 to 25mm thick, as in riser of steps, skirting, dado and pillar etc.; bedded and jointed with grey cement and pointed with white cement with admixture of pigment to match the shade of stone including rubbing / grinding & mirror finish polishing and including 10 mm thick cement screed in cement mortar 1:3 complete all as specified and directed.

20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over and including 15 mm thick screed base in cement mortar 1:6 over and complete all as specified and directed.

Chequered cement concrete coloured tiles, homogenious texture glossy finished , chemically coated machine pressed 30 cm x 30cm x 25mm thick set, jointed and pointed in near cement slurry in floor with gray cement and pigment and including 20 mm thick cement screed in cement mortar 1:4 over and including 75mm thick PCC M-10 (Nominal Mix) type C-2, using 40mm graded crushed stone aggregate complete all as specified and directed. Shade/Colour of tile shall be approved by the GE.

Rendering cement plaster 15mm thick in cement mortar 1:6 (1 cement : 6 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer) on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, all as specified.

Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer) on stone masonry or surface other than fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, all as specified.

Preparation of new steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Preparation of old steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

Preparation of wooden surfaces of any description and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer over complete all as specified and directed.

Preparation of old surfaces of ceiling by washing, rubbing down and stopping of distempered and painted surfaces and applying one coat of white wash complete all as specified and directed.

Preparation of old surfaces of wall by washing, rubbing down and stopping of distempered and painted surfaces and applying one coat of oil bound distemper complete all as specified and directed.

Preparation of old surfaces of wall by Complete removal of existing treatment and applying two coats of acrylic emulsion anti fungal (exterior) weather proof paint over and including a coat of primer complete all as specified and directed.Make:- Berger (weather all coat guard)/ Asain (apex ultima/ Nerolac (excel).

Preparation of newly plastered or un plastered, previously undecorated wall surfaces and applying two coats of acrylic emulsion anti fungal (exterior) weather proof paint over and including a coat of primer over and including 2mm thick wall care putty (applied in two layers), finished smooth with sand paper complete all as specified and directed.

G I tubing medium grade of 15 mm bore with all fittings and fixtures fixed to wall and ceiling or laid in floor/trenches complete all as specified and directed.

All as per ser item No 49 above but except pipe including new fittings as per requirement .

G I tubing medium grade of 20 mm bore with all fittings and fixtures fixed to wall and ceiling or laid in floor /trenches complete all as specified and directed.

All as per ser item No 51 above but except pipe including new fittings as per requirement .

Sink with drainage board (glossy) made of high grade stainless steel 1 mm thick with plugs, washers and waste pipe, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets of angle iron and connecting union to pipe over all size 915 mm x510 mm and bowl size 600mmx450mm x 225mm complete all as specified and directed.

Stainless steel curtain rod, 25 mm bore, powder coated with all fittings i.e. wall bracket, bracket screws, stope and rollers, fixed in repairs all as specified.

Brass chromium plated tubular towel rail 20 mm dia, "D" type, 60 cms long between flanges fixed in repairs with and including chromium plated brass brackets, brass screws complete all as specified

Chromium plated soap dish, fixed in repair complete all as specified.

Stop valves/ angle valve/ concealed valve, cast copper alloy, chromium plated, fancy type, screwed down, high pressure , screwed both ends for 15mm bore iron pipe or for unions and fixed in repairs complete, all as specified. Type of valve approved by the GE.

Bib tap, cast copper alloy ,chromium plated, fancy type , screwed for iron pipe or for brass ferrule of 15 mm bore complete all as specified and directed.

PVC valve less, crystal white, syphonic action type flushing cistern 10 litre capacity, superior quality, plunger type, low level, with inlet, ball valve, float and handle, 32 mm dia PVC long bend flush pipe 90cm long and 15 mm dia 600 mm long PVC connection with CP brass coupling nuts and PVC washers at both ends fixed, in repairs, all as specified. Make: Cat Part No. 2602 of Cera or equivalent in makes mentioned in Appx 'C'.

600x450 mm bevelled edge mirror of slected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plug with chromium plated brass screwed and cup washers.

Vitreous Chinaware squatting pan, ‘Orrisa pattern’ size 580 mm x 440 mm, crystal white, with cast iron ‘P’ or ‘S’ trap, front or back inlet, integral foot rest with provision of plain cement concrete M-15, type B-I using 20 mm graded crushed stone aggregate complete all as specified, incl making connections to trap and to flush pipe, etc and making good to floors to match existing, in repairs, all as specified. Make: Cat Part No. 2071 of 'Cera' or equivalent makes mentioned in Appx 'C'.

32/40 mm dia waste pipe for sinks, basins, etc. fixed in repair complete all as specified and directed.

32/40 mm waste coupling fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

110mm dia PVC(SWR) pipe single socketed with rubber ring joints, laid/fixed to tranches or in floor or walls ,fixed in repair omplete all as specified and directed.

75mm dia PVC(SWR) pipe single socketed with rubber ring joints, laid/fixed to tranches or in floor or walls, fixed in repair complete all as specified and directed.

110 mm dia PVC(SWR) bend, any radius complete all as specified and directed.

75 mm dia PVC(SWR) bend, any radius complete all as specified and directed.

75 mm dia PVC(SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

110 mm dia PVC(SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

110mm dia PVC (SWR) junction single, (single T) equal or unequal provided with oval access door complete all as specified and directed.

75mm dia PVC (SWR) junction single, (single T) equal or unequal provided with oval access door complete all as specified and directed.

Rotational moulded polyethylene water storage tank 500 Ltrs capacity four layered (ISI Marked) cylinderical vertical with closed top, hoisted and fixed in position with ball brass valve, high pressure with PVC float valve 20mm dia with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line complete all as specified.

Taking down point wiring with aluminium/ copper conductor for light point, socket point/ power point etc. in PVC casing and caping, surface pvc/ steel conduits, wood batten with clips including taking down board any type and size complete with any type of switches, sockets, holders, (batten or pendent type), ceiling rose etc. The light fittings (any type), main switches, distribution board with MCB’s of any capacity and make are to be removed/ replaced if required and all as specified and directed. NOTE: - Existing fan regulator any type (Where required) and electric meters are to be refixed and connected properly where required.

Taking down sheet metal enclosure DB, MCB, main switch etc and making good distrubed surfaces to match with existing surface complete all as specified and directed.

Point wiring with 1.5 Sqmm copper conductor FRLS (Multistrand) PVC insulated ISI Marked unsheathed cable in and including PVC casing and caping of approved size, medium grade, ISI marked with all fittings/ accessories as specified in preamble 1 (a) to (q) of Section 19 of SSR Part-II, under heading point wiring and also including PVC insulated ISI marked unsheathed 1.5 Sqmm copper multistranded conductor FRLS as earth wire (green colour) connected to common earth dolly and including pressed steel terminal boxes made out of 1.20 mm thick mild steel sheet duly painted with one coat of red oxide primer for mounting of switches, sockets, fan regulators, light fittings etc. covered with 3mm thick plastic laminated sheet (Make Hylum or equivalent ISI marked) for one light point or one fan point through regulator or one bell point, controlled by one way switch/ push button complete including making good disturbed surfaces to match with existing all as specified and directed.

All as per serial item No '74' above, but for one 3 pin 5 Amps socket outlet on the same board all as specified and directed.

All as per serial item No '74' above, but for one 3 pin 5 Amps socket outlet, independent all as specified and directed.

All as per srl item no 74 above but for one bell point controlled by one one way bell push complete all as specified.

All as per serial item No '74' above, but for one light point controlled by two way switch all as specified and directed.

All as per serial item No. '74' above but for 3 pin 15 Amps socket out let independent with 2.5 Sqmm PVC copper conductor cable and and PVC insulated, unsheathed 2.5 Sqmm stranded copper conductor cable as continuous earth wire, all as specified.

Switch piano flush type, single pole, one way, 5 Amps, all as specified.

Switch piano flush type, single pole, one way, 15 Amps, all as specified.

Switch piano flush type, single pole, two way, 5 Amps, all as specified and directed.

Socket outlet two & three pin 5 Amp flush type, all as specified.

Socket outlet two and three pin, 5 Pin, 5/16 Amp flush type controlled by one switch, all as specified.

Bell push, flush type, 5 amp all as specified.

Musical door bell , AC, 230 volts, single pole all as specified.

Lamp holder, PVC/Polycarbonate type with back plate suitable for angular/ batten fittings with LED lamps, 10 watts all as specified and directed. Make:- CAT Part No LHLDERUEML8X010 of make "Havells" for LED lamp or equivalent in makes mentioned in Appendix "C".

Ceiling rose, 65 mm to 50 mm, two to three terminals, PVC/ Polycarbonate, insulated body fixed on PVC block, all as specified.

Flush type, step fan speed controller suitable for 1200/ 1400 mm sweep ceiling fan complete all as specified and directed.

Sheet metal enclosures for DBs when MCBs to be used, single pole and neutral, 12 way, double door, 240 volts with 200 Amp rated bus bar, all as specified. Make : Indoasian Cat Part No. 811819 or equivalent in makes mentioned in Appx 'C'.

Distribution board iron clad DB double door with IP-43 protection 415 volts 3 phase 50 Hz 4 way complete with appropriate size of copper busbar and neutral link complete and including cutting chasing to wall for fixing DB and making good disturbed wall to match with existing surface complete all as specified. Make- Indo Asian cat part No. 811840 or equivalent in makes mentioned in Appx 'C'.

Taking down old unserviceable light fittings/ bulk head fittings of any type and model complete and making good the disturbed surface complete all as specified.

Pressure die cast housing with epoxy power coated dark graphite grey colour finish prismatic polycarbonate cover with individual LED lenses with 30 watt LEDs as light source complete all as specified. Make- Polycab cat part No PUB0501037 or equivalent in makes mentioned in Appx 'C'.

Street light bracket made out of 32 mm dia GI light grade tubing not less than 1.5 mtr long bend to shape including pole clamps made out of 50 mm X 6 mm iron strip and nut bolts and washers complete all as specified.

Integral steek extruded polycarbonate LED channel 5 watt 1FT complete with white acrylic cover batton integrated connection from ceiling rose connector complete all as specified. Make- Bajaj cat part No. 112406BCLSB 05 NW or equivalent in makes mentioned in Appx 'C'.

LED tube light fitting box type sutable for 1X20W 4FT complete with led tube rod fixed complete to wall / ceiling and PVC round / square block (02nos) of suitable size etc provied complete including from ceiling rose to connector with flexible pipe of suitable size of all complete all as specified. Make- crompton cat part no DMLN1LT8 16 with tube cat part No. LT8-20-865-2 or equivalent in makes mentioned in Appx 'C'.

Disconnecting/ Taking down and refixing in seviceable condition of electric water heater any type/ any capacity removing and cleaning the dust properly, painting with same colour good quality synthethic enemelled paint after preparing surface for painting including refixing and making the conection and testing complete all as specified.

Disconnecting/ Taking down exhaust fan of any size/ any type removing and cleaning the dust properly, painting with same colour good quality synthethic enemelled paint after preparing surface for painting oiling and greasing of bearing including refixing and making the conection and testing complete all as specified.

Disconnecting/ Taking down ceiling fan of size 1200 mm/ 1400 mm sweep removing and cleaning the dust properly, painting with same colour good quality synthethic enemelled paint after preparing surface for painting oiling and greasing of bearing including refixing and making the conection and testing complete all as specified.

Renewal of sub main wiring with two single core PVC insulated cable 1100 volts grade with copper stranded RLS conductor of size 6 Sqmm (2 single run) with one continuous FRLS copper earthing lead wire of size 6 Sqmm and drawn into PVC conduit/ casing & capping with all fittings/ accessories, junction boxes 1 to 4 way 20mm dia, cutting chases, making good in cement mortar (1:3), finishing surfaces to match with existing and connected to common earth dolly including taking down old unservicable submain wiring, complete and as directed. Note :- Two run (each run of 1 RM) of 6 sqmm copper conductor and one RM of earth wire of 6 Sqmm, shall be measured as one RM).

MCB TPN 40 to 63 Amps, 415 Volts, 10 KA all as specified.

MCB SPN 40 to 63 Amp, 240 Volts, 10 KA all as specified.

MCB SP 6 to 32 Amp, 240 Volts, 10 KA all as specified.

MCB SP 40 to 63 Amp, 240 Volts, 10 KA all as specified.

Blanking plate for MCB complete all as specified.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of plate not less than 1.5 metre below ground level, connecting to galvanised iron wire 4.0mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15mm bore including provn of concrete pit in PCC M-15, type B-I using 20mm graded crushed stone aggregates with 40mm thick precast cover of size 550 mm X 550 mm X 75 mm of RCC M-15, type B-I, reinforced with XPM (weight not less than 4 kg/ Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electrical plate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion.

m t construction co