ADDN/ALTN TO TOILET AT RIMC AT VARIOUS BLDG TO CATER TO GENDER SPECIFIC NEED/REQUIREMENT UNDER GE DEHRADUN

Amount

Demolition of brick work in cement mortar including all quoins, arches, pillars etc, but excluding ashler facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Dismantling asbestos cement (corrugated , semi corrugated, etc.) sheets in roof coverings.Complete all as specified and directed.

Taking down Chowkats or frames with shutters (without taking off shutters from the frame) n.exc 1.50 sqm each and removing from site including making good disturbed portions of wall with new or old bricks, lintel, cills etc in CM 1:4 complete all as specified and directed.

Taking down Chowkats or frames with shutters (without taking off shutters from the frame) exc 1.50 sqm but n.exc 4.0 sqm each and removing from site including making good disturbed portions of wall with new or old bricks, lintel, cills etc in CM 1:4 complete all as specified and directed.

Dismantling wall and ceiling board,of any description complete all as specified and directed by Engr-in-Charge

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description & in any position not specifically provided for complete all as specified and as directed

Demolition of cement concrete (un reinforced) in ground floor and paving n. exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Dismantling of cast iron/ PVC /AC /SGSW pipes alongwith fittings and accessories upto 100 mm dia jointed in cement mortar and taking out of walls, floors or trenches, if required complete all as specified and directed.

Dismantling Mild Steel work of any description not otherwise provided for complete all as specified and directed by Engr-in-Charge

Taking up or down 15 mm steel tubing and connections complete all as specified and directed.

Taking up or down 20 mm steel tubing and connections complete all as specified and directed.

Dismantling of water tanks capacity exc 250 ltrs and n.exc 1500 ltrs complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete as directed and specified.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc.Laid, bedded and pointed in any mortar complete as directed and specified.

Taking down cement plaster of any description, thickness on brick, stone, concrete surfaces including racking out joints, hacking for key, scrubbing down with water, removal of rubbish and cleaning, etc complete as directed and specified.

Taking down shutter of any description exc. 1.0 Sqm but n.exc 2.0 Sqm each and removing from site complete all as specified and directed.

Excavation in trenches n exc 1.5m wide and n exc 1.50m in depth for foundation etc and getting out in soft/loose soil complete all as specified and directed by Engineer-In- Charge.

M & L for treating the bottom and sides of excavation at the rate of 5 ltrs of emulsion per sqm of surface area complete all as specified and directed by Engineer-in-Charge

M & L for treating the back fill in contact with foundation at the rate of 7.50 ltr of emulsion per sqm of vertical surface complete all as specified and directed by Engineer-in-Charge

M & L for treating the top surface of filled earth at the rate of 5 ltr of emulsion per square meter of surface area complete all as specified and directed by Engineer-in-Charge

M & L for treating the soil under plinth protection at the rate of 5 ltr of emulsion per square meter of surface area complete all as specified and directed by Engineer-in-Charge

M & L for treating the soil along with external perimeter of building at the rate of 2.25 ltr of emultion per meter of the perimeter wall complete all as specified and directed by Engineer-in-Charge

Returning, filling in, including spreading, levelling, watering and well ramming in l;ayers not exc 25 cm in soft and loose soil complete all as specified and directed by Engineer-in-Charge.

Removing excavated material not exceeding 50M and depositing where directed at a lavel not exceeding 1.5m above the starting point, soil complete all as specified and directed by Engineer-in-Charge.

M&L for providing plain cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation and mass concrete complete all as specified and directed by Engineer-in-Charge.

M & L cement concrete M-25 desigh mix (using 20mm graded aggregate) for foundations, includingf rafts, footings, foundations beams, plinth beams, bases for columns etc complete all as specified and directed by Engineer-in-Charge.

M & L cement concrete M-25 desigh mix (using 20mm graded aggregate) for slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slab, chajjas etc and in shelves and this like complete all as specified and directed by Engineer-in-Charge.

M & L cement concrete M-25 desigh mix (using 20mm graded aggregate) for columns, pillars, piers, post and strut complete all as specified and directed by Engineer-in-Charge.

M & L cement concrete M-25 desigh mix (using 20mm graded aggregate) for beams, cantilivers, beressummers, lintels over 1.5m span complete all as specified and directed by Engineer-in-Charge.

M & L cement concrete M-25 desigh mix (using 20mm graded aggregate) for chajja all as specified and directed by Engineer-in-Charge.

M & L for formwork to sides of concrete , foundations, footings, bases of columns, rafts and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work for rough finished surface complete all as specified and directed by Engineer-in-Charge.

M & L for formwork to soffits of suspended slabs such as roof slabs, floors slabs, landings and similar work not exceeding 200mm thick (horizontal or sloping) for fair finished surface complete all as specified and directed by Engineer-in-Charge.

M & L for formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantiliver shelves etc.for fair finished complete all as specified and directed by Engineer-in-Charge.

M & L for formwork to sides of pillars, posts, struts, piers, columns and stanchions etc.for fair finished surface complete all as specified and directed by Engineer-in-Charge.

M & L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete raillings , opening in concrete walls, floors and roofs n exc 20cm wide and sides of RCC/PCC bands in walls, hozontal or sloping and similar work exc 5cm but n exc 10cm etc.for fair finished surface complete all as specified and directed by Engineer-in-Charge.

M & L formwork to chullah hoods, chajjas, troughs and similar items including edges for fair finished surface complete all as specified and directed by Engineer-in-Charge.

M&L for mild steel TMT bars 10mm dia and over , cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns,footing, plinth beam, roof beam, lintels, slabs and other similar structures etc., hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge

M&L for mild steel TMT bars 8 mm dia and over cut to length and bent to shape required and binding with mild steel wire dia not less than 0.9 mm (annealed) complete all as specified complete all as specified and directed by Engineer-In- Charge

- ditto- as ser item no 36 above but 5mm dia and over upto and inclluding 10mm dia in stirrups, spacers and binders etc complete all as specified and directed by Engineer-in-Charge

M & L excavated earth for spreading and levelling in layers n exc.25 cm thick and well ramming including watering as required complete all as specified and directed by Engineer-in-Charge. (Note : earth will be used brought from item No 17above)

M & L for hardcore of broken bricks of gauge n exc. 63 mm , deposited , spread and levelled and compacted in layers n exc. 15 cm thick , watered and rammed to a true surface complete all as specified and directed by Engineer-in-Charge

M & L for 75 mm thick cement concrete type D-2, 1:4:8 (40 mm graded stone aggregate) as in sub base complete all as specified and directed by Engineer-in-Charge.

M&L for brick work with old size fly ash bricks straight or curved on plan exc 6m radius built in cement motar CM 1:6 complete all as specified and as directed

M&L for brick work with flyash bricks straight or curved on plan in CM 1:4 as in half brick thick walls complete all as specified and as directed

M&L for 15mm thick rendering on other than fair faces of brick work in CM 1 : 6 finished even and smooth without using extra cement complete all as specified and directed by Engineer-In- Charge.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1 : 4 mixed with water proofing compound finished even and smooth without using extra cement complete all as specified and directed by Engineer-In- Charge. (Water proofing compound shall be measure and paid separatelly).

Supply only liquid water proofing compound complete all as specified and directed by Engineer-In- Charge.

M & L for 25 mm thick PCC 1:2:4 type B-0, using 12.5 mm graded stone aggregate as in floors, to receive surface of tile complete all as specified and directed.

M&L for rendering 10mm thick on other than fair face of brick work surfaces in CM 1:4, complete all as specified and directed.

M&L for screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6, for laying floor finishes/ tiles complete all as specified and directed.

M&L for screed bed or bedding layer of mortar, 20 mm thick, in cement mortar 1:6, for laying floor finishes/ tiles complete all as specified and directed.

M&L for glazed coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, on floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L Glazed ceramic tiles coloured 450 x 350mm, 300mmx 450mm , 7 to 8 mm thick, set and jointed on vertical surface in neat cement slurry and pointed in white or colour cement to match etc complete all as specified and and as directed

M&L for cement concrete 1:2:4 type, B1 using 20 mm graded stone aggregates as in copings, roof padding/staging of water tank etc including necessary fromwork, weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed

M&L for form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beamschullah hoods, chajjas, troughs and similar items including edges for rough finished surfaces of concrete flat, complete all as specified and directed.

M & L 18 to 20mm thick granite(Zed Black colour as approved by GE) stone slab machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing as in kitchen platform/dado/skirting /plateform counter top WHB in cluding cutting holes for oval shape /urinal partitions etc. including 15 mm thick cement screed bed 1:6 CM in horizontal or vertical surfaces including grinding the edges half round and polishing complete all as specified and directed by Engineer-In- Charge.

M & L for cutting chases, pinning in brick/PCC blocks wall in making good to facings where required and pointing in cement mortar 1:3 and cutting chases for concealed water tubing etc and making good complete all as specified and as directed

S&F medium grade galvanized steel tubing with all fittings &fixed complete to walls & ceiling or laid in floors 15 mm dia bore pipe (including in short length) complete all as specified and as directed

S&F tubes medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors 20 mm dia bore pipe (including in short length) complete all as specified and as directed

Supply & fixing factory made single extruded WPC(Wood polymer composite) Solid door frame/ chowkat of size 100X50 comprising of virign PVC polymer of K value 58-60 (suspension grade ) calcium corbonate and natural fibers ( wood powder/rice husk /wheat husk) and non toxic additives (max toxicity index of 12 to 100 gms) fabricated with mitred joints and applying PVC solvent cement and screwed with full body threaded star headed SS screws having min frame density of750Kg/cum screw withdrawal strength of 2200 N (face) & 1100 N edge,minimum compressive strength of 58 N/mm2, moduus of elasticity 900N/mm2 and resistance to spread of flame of class 'A' category with property of being termite / borer proof, water / moisture proof & fire retardant & fixed in postion with SS dash fasterns / hold fast of required dia and length,colour of door frame to match that of shutter all as specified and directed.

S&F factory made single extruded WPC (Wood polymer Composite) Solid moulded Flush Door Shutter of 30 mm size comprising of virgin PVC resin of K value 58-60 (Suspension Grade), Calcium Carbonate and natural Fibers (Wood Powders/ rice husk/ wheat husk) and Non toxic additives (max toxicity index of 12 for 100 gms) having min density of 650 Kg/Cum and screw withdrawal strength of 1800 N (Face) &900 N (Edge) Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of class A category with property of being Termite/ Borer proof. Water/ Moisture Proof, Fire retardant and fixing with stainless steel but hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer - in- Charge, Materia test certificate and authentication should be compulsory provided by the manufacturing company.

M & L PCC 1:3:6 Type C 0 usind 12.5 mm graded stone aggregate for backing of door chawkhats complata all as specified and directed by Engr-in Charge

S&F Aluminium anodised tower bolt 200 mm long of extruded section etc complete all as specified and as directed

Aluminium alloy, anodised, sliding door bolt size 300 mm with hasp, staple (bolt ype) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed. Complete all as specified and directed by Engr-In-charge.

S&F 150 mm long aluminium handle, cast type, anodised etc complete all as specified and as directed

M&L 75mm thick PCC 1:3:6 type C-2, (20 mm graded stone aggregate)as plinth protection and finishing even and smooth without using extra cement incl making joints 12 mm wide of full depth of PCC at every 3 meters and at every change in direction and filling the same with sealing compund grade 'A' incl necessary formwork. Complete all as specified and directed.

7Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ for thickness of 75mm complete all as speicified and directed

S&F 500 litre rotational moulded tripple layer polyethlene water storage tanks white colour (cylindrical vertical with closed top) and suitable size of MS tasla with locking system hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

S&F 20mm ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed etc complete all as specified and as directed

&F as in repair Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe 20 mm bore and fixed as in repair complete all as specified and as directed

S&F vitreous China corner wash hand basin, size as per manufacturer any design approved by GE including 15mm dia CP brass waste coupling, 450 mm long HDPE PVC connection, 750 mm long 32mm bore HDPE waste down pipe including CI brackets complete all as specified and directed.

S & F Brass CP wall mixer 15 mm bore (wall mounted type) for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and as directed

S & F in repair fancy type 125mm size square brass CP shower rose with or without swivel joints complete all as specified and as directed.

S&F brass chromium plated bottle traps for wash basins, urinals with inlet and outlet screwed for pipe or connections inclding necessary packing union and cap and fixed complete all as specified and directed.

S&F in repair bib tap long body fancy type cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule or fixed for 15 mm dia bore pipe complete all as specified and as directed

S&F in repair stop valves/angle valves fancy type chromium plated brass cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions fixed for 15 mm dia bore pipe complete all as specified and as directed

S&F in repair tubular towel rail 20mm dia type brass chrormium plated 600mm long between flanges complete all as specified and as directed

S&F in repair PVC connection of 30 cm length including brass nuts complete all as specified and as directed

S&F in repair PVC connection of 45 cm length including brass nuts complete all as specified and as directed

S&F fancy type brass chromium plated soap dish of 160x160x90 mm complete all as specified and directed.

S&F fancy type glass corner 300mm radius of 10mm thick toughned glass with CP railing fixed with fancy type screws complete all as specified and directed.

&F in repairs vitreous china squatting pan orissa pattern long pan size 580 mm x440mm white with spun pipe ‘P’ or ‘S’ trap, front or back inlet and foot rests excluding flushing cistern & flush pipe but incl. cement concrete bedding fixed complete all as specified and as directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern) with 'S' trap white, including connection to drain or out going pipe and flush pipe anti symphonize pipes etc complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern) with 'P' trap white, including connection to drain or out going pipe and flush pipe anti symphonize pipes etc complete all as specified and directed.

S&F in repair PVC low level flushing cistern 10 litres, valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, flushing pipe for pedestal pan complete all as specified and directed.

S&F in repair PVC low level flushing cistern 10 litres, valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, flushing pipe for squatt pattern complete all as specified and directed.

S&F vitreous china urinals half stall urinal (back or corner wall type) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing complete incl making good exisiting surface.

S&F in repairs vitreous chinaware coloured wash hand basin with pedestal of size 55X40 cm complete including waste coupling ,waste pipe including fixing arrangement and cutting for and pinning in walls & making good complete all as specifed and directed.

S7F in repair pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, fancy type screwed for iron of 15mm pipe and fixed

S&F in repair health faucet mild steel chromium plated suitable for 15mm dia pipe with 1 or 1.25mtrmetre long flexible tube and ABS wall hook fixed to wall all as specified and directed

S&F in repair for 75 mm bore out let cast floor trap spun pipe (conforming to IS 3989) incl cockroach trap with gratings including including jointing to waste pipe fixed in cement concrete tpe B-1 (1:2:4) etc complete all as specified and as directed

S&F for 75 mm bore Cast iron spun pipe (conforming to IS 3989) soil, waste and vent pipes, in any length with or without ears with lead joints, laid in trenches or in floors or fixed to wall vertically complete all as specified and as directed

S&F for 75 mm bore Cast iron spun pipe (conforming to IS 3989) soil, waste and vent pipes, in any length with or without ears with lead joints, fixed to wall vertically complete all as specified and as directed

S&F for 100 mm bore Cast iron spun pipe (conforming to IS 3989) soil, waste and vent pipes, in any length with or without ears with lead joints, laid in trenches or in floors or vertically cast, complete all as specified and as directed

S&F 100 mm bore cast iron Bends of (any radius), spun pipe (conforming to IS 3989) diminishing piecs or tapers (larger bore measured) complete all as specified and as directed

S&F 75 mm bore cast iron Bends of (any radius), spun pipe (conforming to IS 3989) diminishing piecs or tapers (larger bore measured) complete all as specified and as directed

S&F 50 mm cast iron cowls spun pipe (conforming to IS 3989) complete all as specified and as directed

S&F forfactory made Steel ventilator with top hung shutter including hinges, steel peg stay, complete Note: Glass shall be measured and paid seperately.

S&F for mild steel window grills box type framed work as in window guard bars, grills or forged into spikes, framed balusters, walkway railing and similar work including welding, FE-290 grade E-165 complete all as specfied and directed.

S&F sheet glass ordinary quality 4mm thick and glazing with oil putty or fixed with bead/ glazing pins in squares n.exc. .5 sqm each pane all corner of glass to be fixed with silicon complete all as specified and directed.

S&F 4 mm thick Figured glass, pin head type and glazing with oil putty in squares n.exc 0.5 sq. m in each pane complete all as specified and directed.

&F MS joist channel (Fe 410-W Gde E-250 Quality A), angle or Tee section,MS tubes, flats square bars etc fixed indepently or framed or without connecting plates ,trusses etc any type framing including purlins and rafters etc confirming to Grade Fe 410-0 or Fe-310-0 complete all as specified and directed by Engr-in-Charge

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed

S & F pre-painted galvalume aluminium zinc coating GI based corrugated steel 0.50 mm thick of any colour as directed by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge

S & F pre-painted galvalume aluminium zinc coating GI based plain steel 0.50 mm thick for ridge cover of any colour as directed by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge

M & L 595 mm X 595mm false ceiling system , using hot dipped galvanised steel section exposed surface with precoated capping, GI powerd coated tee and cross tee of size 24x32mm & 24x27mm having 0.27mm gauge at every 600mm c/c interval and wall angle of size 19x19mm having 0.35mm gauge fixed to the wall. The above grid is tobe suspended at every 1200mm c/c in both direction using 2mm thick pre-straightened GI wire laying designer tile ivory painted (high pressure steam cured) of 4 mm thickness (as per IS 14862) of size 595x595 mm and ant ine of the design (cascadev or electra) , back of the tile duly sanded and finished with a coat of protective paint over the formed grid etc complete all as specified and directed by Engineer-in-Charge.

M&L for complete removal of existing treatment from wall upto plaster surface by washing, rubbing down and stopping of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces finally rubbed and smooth with sand paper priming plastered and other surfaces with alkaliresistant priming paint all as directed by Engr-in-charge.

Providing and applying external water proof wall putty of 1 mm thickness over plastered surface to prepare the surface even and smooth.

M&L for applying two coats of acrylic distemper over a coat of primer, white or tinted over 0.75 to 1 mm thick wall care putty in two coat complete all as specified & directed.

Material & Labour for preparation of new surface applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm. Complete all as specified and directed.

Material & Labour for preparation of old surface applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm. Complete all as specified and directed.

M&L three coats of white wash on ceiling on new/old plastered surfaces including preparation of surfaces complete all as specified and as directed

M&L for providing plain cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in foundation and mass concrete complete all as specified and directed by Engr-In- Charge.

M&L for providing precast cement concrete coping with plain fair faces incl chamferes, weathering, throating etc type B0, 1:2:4 using 12.5mm graded stone aggregate and set in CM 1:4 complete all as specified and directed by Engineer-In- Charge.

M & L for cement concrete 1:3:6 type C-2 for 150 mm dia in concrete bed to drain pipes including packing under and haunching against the sides of pipes etc complete all as specified and directed by Engineer-In- Charge

M & L for reinforced concrete pipes,150mm dia class NP-2 laid and jointed complete with collars complete all as specified and directed by Engineer-In- Charge.

Cutting into existing manholes for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 or 3/4 section ) in cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate finished smooth and reforming benching as required for 150mm dia pipes complete all as specified and directed by Engineer-In- Charge.

M&L for providing pre cast RCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in cover slab and man hole covers etc complete all as specified and directed by Engineer-In- Charge.

M/L PCC 1:3:6 type C0 ( using 12.5 mm thick graded stone aggragate) as in surface channel drain. Complete all as specified and directed

S&F Providing precast cement concrete louvres and jallies, in 1:3:6 type C0 ( using 12.5 mm thick graded stone aggragate) 25mm thick fixed in CM 1:6 (mea sured solid), including all mould- ings but excluding frame complete all as specified and directed

S& F push button taps of cast copper alloy, screwed for iron pipe and fixed to 15mm pipe complete all as specified and directed.

S&F urinal spreader of PTMT/ABS body of any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms)

Taking down carefully existing aluminium/copper point wiring on batten or in PVC conduit or in MS conduit with GI earth wire etc ( light, fan, socket, or power and switch, socket, regulator, holders, ceiling roses) complete and making good the disturbed surfaces of walls, Floors, ceilings etc to match with existing all as specified and directed.

M & L for point wiring complete with 3 runs (P + N+ Earth) of PVC insulated, unsheathed, FRLS, 1100 volt grade, size 1.5 sqmm, multi stranded, copper conductor single core in and including rigid PVC concealed Conduit not less than 19 mm dia, clip, complete with all accessories such as socket, elbow, junction box, bell mouth, bend, reducer etc including MS Box of thickness1.2mm for mounting of switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet as top cover, and earth wire connected to earth dolly complete all as specified, required for One light/fan point controlled by one switch , complete all as specified and directed.

All as per item No 2 here in before , but for One three pin 5 Amp socket on same board with other switches.

All as per item No 2 here in before, but for One three pin 5 Amp socket on independent board.

All as per item No 2 here in before, but with 4 Sqmm. (nominal area) wire/cable for one 3 Pin 15 amp socket on independent board

S&F ceiling rose surface bakelite 3 terminals of size 65x25mm. complete .

S&F switch modular 6 Amps 230 Volts one way switch.

S&F switch modular 10 Amps , 2 way , 230 Volts switch.

S & F Fan Regulator electronic rotary,0-4 steps step type 100 Watt, 240 Volt 50 Hz hum free 2 module complete all as specified and directed.

S&F Socket 6 Amps AC 230 Volts 2/3 pin combined 2 modular type complete all as specified

S&F Socket 6A/16 Amps-2/3 pin AC 230 Volts modular type complete all as specified and as directed.

S&F Switch modular type AC 230 volts 16 Amps one way complete all as specified and as directed.

S & F Modular white cover plate with frame 2 module and metal flush box 2 module complete all as specified and as directed.

All as per item No 13 here in before but 3 module

All as per item No 13 here in before but 4 module

All as per item No 13 here in before but 6 module

All as per item No 13 here in before but 8 module

All as per item No 13 here in before but 12 module

M&L lamp holder PVC/polycarbonate type with LED lamp 9/10 watt complete all as specified & directed

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed

S&F LED luminaire 600x600mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver 3 core flexible copper conductor complete., complete all as specrified & directed

S&F tube light fitting 1x20/22 watts and connected to ceiling rose with required length of two core flexible copper cable 23/0.0076 fixed on wall/roof complete all as specified and directed.

S&F round/square shape 12 watt Sky Spot COB (WW) 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with 3 core flexible copper conductor cable, complete all as specified and directed by Engineer-in-charge

S&F LED flood light 70 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp, fixed on pole duly fixed on angle iron bracket complete all as specified and directed.

S&F Exhaust fans AC metallic body ,single phase 230/ 240 V of size 300 mm sweep,50 Hz with louver, louvers & shutters and connecting up ceiling rose to connector block of fan including making of holes and grouting of nuts and bolts PCC (1:2:4) B-1 block including complete all as specified and directed.

S&F Water heater storage type, electric, capacity 25 litres AC single phase 230/ 240 V o and connecting up including making of holes and grouting of nuts and bolts PCC (1:2:4) B-1 block complete all as specified and directed.

S&F in replacement sheet metal enclosures TPN 415 Volt 4 way with suitable rated bus bar for Single door IP-43DB's including taking down old one complete all as specified and directed .

S&F sheet metal enclosures 240 volt 8 way with suitable rated bus bar for Single door IP-43DB's complete all as specified and directed .

S&F MCB SP 240 volt 10 KA 5 to 40 Amp, conforming to relevant IS complete all as specified & directed.

S&F MCB SPN 240 Volt 10 KA 40 Amp conforming to IS complete all as specified

S&F MCB TPN 415 Volt 10 KA 63 Amp conforming to IS complete all as specified

S&F metal clad single pole and neutral enclosure with 2 pin and earth plug and socket complete with and including one single pole MCB 20 Amp 240Volt complete.

M&L for submain wiring with 3 runs(N+P+E) of 1.5 Sqmm single core,PVC insulated, unsheathed, multistranded copper conductor FRLS cable 1100 volts grade drawn through and including concealed/surface PVC conduit pipe of medium duty not less than 15 mm dia including necessary PVC conduit specials and connecting with suitable size thimble, including taking old wiring complete all as specified and directed. Note:-3 runs of 1.5 Sqmm size PVC copper cable, and one run of PVC conduit shall be measured as one unit length.

All as per item No 33 but with 3 runs(N+P+E) of 2.5 Sqmm single core copper FRLS conductor . Note:-3 runs of 2.5 Sqmm size PVC copper cable, and one run of PVC conduit shall be measured as one unit length.

All as per item No 33 but with 3 runs(N+P+E) of 4 Sqmm single core copper FRLS conductor .Note:-3 runs of 4 Sqmm size PVC copper cable, and one run of PVC conduit shall be measured as one unit length.

All as per item No 33 but with 6 runs(3 runs P+N+ 2 run Earth) of 6 Sqmm single core copper FRLS conductor and PVC conduit not less than 24 mm dia. Note:-6 runs of 6 Sqmm size PVC copper cable, and one run of PVC conduit shall be measured as one unit length.

M&L Earthing complete with GI earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to GI earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of GI or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion complete all as specified and as directed.

PRAGATI ENTERPRISES

R K BUILDERS