FIRE

SUPPLY AND FIXING GYP BOARD SUSPENDED REGULAR SINGLE LAYER FALSE CEILING (GS-MFSC-4.1 AS PER INDIA GYPSUM) USING 12.50 MM THICK GYP BOARD CONFORMING TO IS 2095-1982 FIXING TO GYP STEEL GI PERIMETER CHANNELS OF SIZE 20 X 27 X 30 MM (WEB) OF 0.55 MM THICK ALONG THE PERIMETER OF CEILING SCREW FIXED TO BRICK WORK / PARTITION AT 610 MM C/C AND SUSPENDING THE FRAME WORK USING INTERMEDIATE CHANNELS (45 X 15 X 15 X 0.90 MM) FROM SOFFIT AT 1220 MM C/C WITH CEILING ANGLE (25 X 10 X 0.55 MM) FIXED WITH GI CLEAT AND STEEL EXPANSION FASTENERS & CONNECTING CLIP TO THE CEILING CHANNELS (WITH KNURLED WEB OF 51.50 X 26 X 10.50 X 0.55 MM) FIXED IN DIECTION PERPENDICULAR TO THE INTERMEDIATE CHANNEL AT 457 MM C/C AND FIXING THE 12.50 MM DRYWALL SCEWS AT 230 MM C/C & JOINTING, FIXING USING JOINT COMPOUND AND PAPER TAPE TO HAVE A FLUSH LOOK INCLUDING FILLING THE TAPPERED & SQUARE EDGES WITH JOINTING COMPOUND, TWO COATS OF DRYWALL TOPCOAT COMPLETE FOR FINISHED ITEM OF WORK AS PER INDIA GYPSUM LTD., SPECIFICATION. FOR SFO & DFO CABINS

Pre-construction Anti-termite is a process in which chemical toxicto subterre an termites is apply/ inject into soild uringearly stage of building Construction 2.Treatement of soil Beneath the building and around the foundations conduct and chemical use as per BIS -IS6313(Part 2) 2013 code specification &CIBR Cregistered termiticide which create sacontinuous chemical barrier beneath the building which kills orrepels terminates&impervious totremite entry Imidacloprid30.5%SC(IS63131)dissolve 2.1 Ml/1 liter of water and apply emulsion/solution @7.5Litres/Squaremeter (Sqm) of internal, external vertical surface of the colums, plinth beams (Back filling)walls and floor junction,external perimeters, along reatining [email protected]/Sqm of the horizontal surface of basement top surface of te basement filling below flooring bed(Plinth) & @ 2.0 Litres/ Line meter at expansion joints. The substructure of a depth of 500mm around coulmns &300mm deep around plinth beams,basements & floor filling area including excavation channel along the wall & rodding etc. cost & Conveyance of all materials to the site, cost of labour for sparying, rodding etc.complete for furnished item of work as per the approval of the Engineer-in-charge

EARTH WORK EXCAVATION FOR FOUNDATIONS AND DEPOSITING ON BANK, FOR ALL LIFTS AND WITH AN INITIAL LEAD OF 10M INCLUDING ALL INCIDENTAL, OPERATIONAL, LABOUR CHARGES SUCH AS SHORING, SHEETING, PLANKING, STRUTTING, ETC. COMPLETE FOR FINISHED ITEM OF WORK EXCLUDING DEWATERING CHARGES ETC AS PER SS - 20 B FOR STIFF BLOCK COTTON SOIL , HARD RED EARTH, MURRAM, ORDINARY GRAVEL - MANUAL MEANS UP TO 3M DEPTH - FOUNDATION OF BUILDING (APSS 308).

CEMENT CONCRETE (1:5:10) PROP. USING 40MM HARD GRANITE MACHINE CRUSHED METAL WITH MACHINE MIXING UP TO PLINTH LEVEL INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LAYING, CURING, FINISHING, ALL OTHER INCIDENTAL, OPERATIONAL, LABOUR CHARGES BUT EXCLUDING SEIGNIORAGE CHARGES ETC., COMPLETE FOR FINISHED ITEM OF WORK. FOUNDATION BED AND UNDER STONE SLAB FLOORING. (APSS NO: 402).

RE-FILLING WITH EXCAVATED EARTH IN LAYERS NOT EXCEEDING 15 CM THICK, CONSOLIDATING EACH DEPOSITED LAYER BY WATERING AND RAMMING INCLUDING COST AND CONVEYANCE OF WATER TO WORK SITE AND ALL INCIDENTAL, OPERATIONAL, LABOUR CHARGES BUT EXCLUDING SEIGNIORAGE CHARGES ETC., COMPLETE FOR FINISHED ITEM OF WORK. IN TRENCHES, SIDES OF FOUNDATIONS AND BASEMENT. (APSS NO. 309 & 310)

MASONRY WORK IN CM (1:6) PROP WITH FLYASH CEMENT SOLID BLOCKS OF SIZE 290 X 225 X 140 MM WITH A COMPRESIVE STRENGTH NOT LESS THAN 50 KG/SQM INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, LABOUR CHARGES, SCAFFOLDING AND CURING BUT EXCLUDING SEIGNIORAGE CHARGES ETC., COMPLETE FOR FINISHED ITEM OF WORK. SUPERSTRUCTURE WALLS 225 MM THICK GROUND FLOOR (APSS NO. 501&504).

VRCC M - 20 NOMINAL MIX (CEMENT:FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND), COARSE AGGREGATE, WATER ETC., TO SITE AND INCLUDING SALES & OTHER TAXES ON ALL MATERIALS, SHUTTERING, CENTERING WITH STEEL PLATES, INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS MACHINE MIXING, LAYING CONCRETE, VIBRATING, CURING ETC.,COMPLETE BUT EXCLUDING SEIGNIORAGE CHARGES, COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK, FOR FOOTINGS (APSS NO.403)

VRCC M - 20 NOMINAL MIX (CEMENT:FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND), COARSE AGGREGATE, WATER ETC., TO SITE AND INCLUDING SALES & OTHER TAXES ON ALL MATERIALS, SHUTTERING, CENTERING WITH STEEL PLATES, INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS MACHINE MIXING, LAYING CONCRETE, VIBRATING, CURING ETC.,COMPLETE BUT EXCLUDING SEIGNIORAGE CHARGES, COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK, FOR PLINTH BEAMS (APSS NO.403)

VRCC M - 20 NOMINAL MIX (CEMENT:FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND), COARSE AGGREGATE, WATER ETC., TO SITE AND INCLUDING SALES & OTHER TAXES ON ALL MATERIALS, SHUTTERING, CENTERING WITH STEEL PLATES, INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS MACHINE MIXING, LAYING CONCRETE, VIBRATING, CURING ETC.,COMPLETE BUT EXCLUDING SEIGNIORAGE CHARGES, COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK, FOR GROUND FLOOR COLUMNS (APSS NO.403)

PLASTERING TO SUPERSTRUCTURE 12 MM THICK IN TWO COATS, WITH A BASE COAT OF 8 MM THICK IN CM (1:6) PROP. AND TOP COAT OF 4 MM THICK IN CM (1:4) PROP. WITH DUBARA SPONGE FINISHING, INCLUDING MAKING GROOVES, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES, SCAFFOLDING, CURING, ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES BUT EXCLUDING SEIGNIORAGE CHARGES ETC., COMPLETE.FOR FINISHED ITEM OF WORK. GROUND FLOOR (APSS NO: 901&904)

PAINTING WITH EXTERIOR EMULSION PAINT OF APPROVED MAKE (ACE FROM ASIAN PAINT) AND COLOUR 2 COATS BY DILUTING 1LIT OF EMULSION PAINT WITH A MAXIMUM 750 ML OF WATER WITHIN AN INTERVAL OF NOT LESS THAN 6 HOURS BETWEEN TWO COATS OVER 1 COAT OF ASIAN EXTERIOR WALL PRIMER BY DILUTING 1LIT. OF PRIMER WITH 1LIT. OF WATER (TOTAL 3 COATS) WITH SURFACE PREPARATION ETC., AS PER STANDARD SPECIFICATION INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, BRUSHES, ALL INCIDENTAL, OPERATIONAL & LABOUR CHARGES, CURING, SCAFFOLDING ETC., COMPLETE FOR FINISHED ITEM OF WORK. ALL FLOORS (APSS NO:908)

PROVIDING "HYSD" STEEL BARS OF DIFFERENT DIAMETERS BELOW 36MM DIAMETER (Fe - 500 GRADE AS PER IS 1786 - 1979)FOR REINFORCEMENT INCLUDING CUTTING, BENDING TO REQUIRED SIZES AND SHAPES, PLACING THEM IN POSITION WITH COVER BLOCKS OF APPROVED SHAPE AND SIZE, TYING FIRMLY WITH M.S BINDING WIRE OF SWG, FORMING GRILLS FOR REINFORCEMENT WORKS AS PER APPROVED DESIGNS AND DRAWINGS TO BE SUPPLIED AT THE TIME OF EXECUTION OF WORK INCLUDING COST AND CONVEYANCE OF DEFORMED BARS, BINDING WIRE, COVER BLOCKS AND ALL WASTAGES SUCH AS OVER LAPS, COUPLINGS, WELDED JOINTS, CHAIRS, SPACE BARS ETC., AS DIRECTED BY THE ENGINEER-IN-CHARGE AND ALL OPERATIONAL, INCIDENTAL LABOUR CHARGES SUCH AS CUTTING, BENDING, PLACING IN POSITION, TYING ETC., COMPLETE FOR FINISHED ITEM OF WORK FOR ALL LENGTHS AS PER DRAWINGS AND TECHNICAL SPECIFICATIONS FOR BARS BELOW 36MM DIA WHERE THEY ARE NOT WELDED.

EARTH WORK EXCAVATION FOR FOUNDATIONS AND DEPOSITING ON BANK, FOR ALL LIFTS AND WITH AN INITIAL LEAD OF 10M INCLUDING ALL INCIDENTAL, OPERATIONAL, LABOUR CHARGES SUCH AS SHORING, SHEETING, PLANKING, STRUTTING, ETC. COMPLETE FOR FINISHED ITEM OF WORK EXCLUDING DEWATERING CHARGES ETC AS PER SS - 20 B FOR STIFF BLOCK COTTON SOIL , HARD RED EARTH, MURRAM, ORDINARY GRAVEL - MANUAL MEANS UP TO 3M DEPTH - FOUNDATION OF BUILDING (APSS 308).

CEMENT CONCRETE (1:5:10) PROP. USING 40MM HARD GRANITE MACHINE CRUSHED METAL WITH MACHINE MIXING UP TO PLINTH LEVEL INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LAYING, CURING, FINISHING, ALL OTHER INCIDENTAL, OPERATIONAL, LABOUR CHARGES BUT EXCLUDING SEIGNIORAGE CHARGES ETC., COMPLETE FOR FINISHED ITEM OF WORK. FOUNDATION BED AND UNDER STONE SLAB FLOORING. (APSS NO: 402).

RE-FILLING WITH EXCAVATED EARTH IN LAYERS NOT EXCEEDING 15 CM THICK, CONSOLIDATING EACH DEPOSITED LAYER BY WATERING AND RAMMING INCLUDING COST AND CONVEYANCE OF WATER TO WORK SITE AND ALL INCIDENTAL, OPERATIONAL, LABOUR CHARGES BUT EXCLUDING SEIGNIORAGE CHARGES ETC., COMPLETE FOR FINISHED ITEM OF WORK. IN TRENCHES, SIDES OF FOUNDATIONS AND BASEMENT. (APSS NO. 309 & 310)

FILLING WITH CARTED GRAVEL OBTAINED FROM APPROVED QUARRY IN LAYERS NOT EXCEEDING 15 CM THICK, IN BASEMENTS, CONSOLIDATING EACH DEPOSITED LAYER BY WATERING AND RAMMING INCLUDING COST AND CONVEYANCE OF WATER TO WORK SITE AND ALL OPERATIONAL, INCIDENTAL, LABOUR CHARGES, HIRE CHARGES OF T & P BUT EXCLUDING SEIGNIORAGE CHARGES ETC., COMPLETE FOR FINISHED ITEM OF WORK. (APSS NO. 309 & 310)

MASONRY WORK IN CM (1:6) PROP WITH FLYASH CEMENT SOLID BLOCKS OF SIZE 290 X 225 X 140 MM & 290 X 100 X 140 MM WITH A COMPRESIVE STRENGTH NOT LESS THAN 50 KG/SQM INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, LABOUR CHARGES, [EXCLUDING SEIGNIORAGE CHARGES], SCAFFOLDING AND CURING ETC., CPOMPLETE FOR FINISHED ITEM OF WORK. BASEMENT WALLS 335 MM THICK.

MASONRY WORK IN CM (1:6) PROP WITH FLYASH CEMENT SOLID BLOCKS OF SIZE 290 X 225 X 140 MM WITH A COMPRESIVE STRENGTH NOT LESS THAN 50 KG/SQM INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, LABOUR CHARGES, SCAFFOLDING AND CURING BUT EXCLUDING SEIGNIORAGE CHARGES ETC., COMPLETE FOR FINISHED ITEM OF WORK. SUPERSTRUCTURE WALLS 225 MM THICK GROUND FLOOR (APSS NO. 501&504).

MASONRY WORK IN CM (1:4) PROP WITH FLYASH CEMENT SOLID BLOCKS OF SIZE 290 X 110 X 140 MM WITH A COMPRESIVE STRENGTH NOT LESS THAN 50 KG/SQM ,INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, LABOUR CHARGES, EXCLUDING SCAFFOLDING AND CURING ETC., COMPLETE FOR FINISHED ITEM OF WORK INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, LABOUR CHARGES, SCAFFOLDING AND CURING ETC., COMPLETE FOR FINISHED ITEM OF WORK. PARTITION AND PARAPET WALLS 100 MM THICK GROUND FLOOR (APSS NO. 501&504).

VRCC M - 20 NOMINAL MIX (CEMENT:FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND), COARSE AGGREGATE, WATER ETC., TO SITE AND INCLUDING SALES & OTHER TAXES ON ALL MATERIALS, SHUTTERING, CENTERING WITH STEEL PLATES, INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS MACHINE MIXING, LAYING CONCRETE, VIBRATING, CURING ETC.,COMPLETE BUT EXCLUDING SEIGNIORAGE CHARGES, COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK, FOR FOOTINGS (APSS NO.403)

VRCC M - 20 NOMINAL MIX (CEMENT:FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND), COARSE AGGREGATE, WATER ETC., TO SITE AND INCLUDING SALES & OTHER TAXES ON ALL MATERIALS, SHUTTERING, CENTERING WITH STEEL PLATES, INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS MACHINE MIXING, LAYING CONCRETE, VIBRATING, CURING ETC.,COMPLETE BUT EXCLUDING SEIGNIORAGE CHARGES, COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK, FOR PLINTH BEAMS (APSS NO.403)

VRCC M - 20 NOMINAL MIX (CEMENT:FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND), COARSE AGGREGATE, WATER ETC., TO SITE AND INCLUDING SALES & OTHER TAXES ON ALL MATERIALS, SHUTTERING, CENTERING WITH STEEL PLATES, INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS MACHINE MIXING, LAYING CONCRETE, VIBRATING, CURING ETC.,COMPLETE BUT EXCLUDING SEIGNIORAGE CHARGES, COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK, FOR GROUND FLOOR COLUMNS (APSS NO.403)

VRCC M - 20 NOMINAL MIX (CEMENT:FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND), COARSE AGGREGATE, WATER ETC., TO SITE AND INCLUDING SALES & OTHER TAXES ON ALL MATERIALS, SHUTTERING, CENTERING WITH STEEL PLATES, INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS MACHINE MIXING, LAYING CONCRETE, VIBRATING, CURING ETC.,COMPLETE BUT EXCLUDING SEIGNIORAGE CHARGES, COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK, FOR LINTELS (APSS NO.402)

PLAIN CEMENT CONCRETE (1:3:6) PROP. USING 20MM GRADED HARD GRANITE MACHINE CRUSHED METAL INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE,CENTERING USING STEEL SCAFFOLDING PIPES, JACK PROPS, STEEL CENTERING PLATES ETC.,, MACHINE MIXING, LAYING, CURING, FINISHING, ALL OTHER INCIDENTAL, OPERATIONAL, LABOUR CHARGES BUT EXCLUDING SEIGNIORAGE CHARGES ETC., COMPLETE FOR FINISHED ITEM OF WORK. BED BLOCKS IN GROUND FLOOR (APSS NO: 402).

PLASTERING TO SUPERSTRUCTURE 12 MM THICK IN TWO COATS, WITH A BASE COAT OF 8 MM THICK IN CM (1:6) PROP. AND TOP COAT OF 4 MM THICK IN CM (1:4) PROP. WITH DUBARA SPONGE FINISHING, INCLUDING MAKING GROOVES, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES, SCAFFOLDING, CURING, ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES BUT EXCLUDING SEIGNIORAGE CHARGES ETC., COMPLETE.FOR FINISHED ITEM OF WORK. BASEMENT WALLS (APSS NO: 901&904)

PLASTERING TO SUPERSTRUCTURE 12 MM THICK IN TWO COATS, WITH A BASE COAT OF 8 MM THICK IN CM (1:6) PROP. AND TOP COAT OF 4 MM THICK IN CM (1:4) PROP. WITH DUBARA SPONGE FINISHING, INCLUDING MAKING GROOVES, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES, SCAFFOLDING, CURING, ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES BUT EXCLUDING SEIGNIORAGE CHARGES ETC., COMPLETE.FOR FINISHED ITEM OF WORK. GROUND FLOOR (APSS NO: 901&904)

TOILET DOOR: 0.75X2.10 M: SUPPLYING POSITIONING AND FIXING WPC SOLID DOOR SHUTTER OF 28MM THICK OF ECHON OR EQUIVALENT MAKE INCLUDING WPC DOOR FRAME MADE WITH WPS SCANTLINGS OF SIZE 100MM X 63 MM OF MAKE FUTURE PLY / WOOD PLUS / LIFE TIME , INCLUDING 6 NOS OF 'Z' HOLD FASTS OF SIZE 230 X 40 X 3MM , 4 NOS OF 125 MM BUTT HINGES, 2 NOS. 125MM LONG DOOR HANDLES, 1 NOS ALDROP OF SIZE 200 MM LONG, 1 NOS. of 200MM LONG TOWER BOLTS, WITH BOLTS, NUTS, NF SCREWS, INCLUDIMG CAST AND CONVEYANCE OF ALL MAERIALS TO SITE, LABOUR CHARES FOR MAKIN THE FRAMES, SHUTTER, MINOR EXTRA FIXTURES REQUIRED IF ANY AS DIRECTED BY THE ENGINEER-IN-CHARG OF THE WORK COMPLETE FOR FINISHED ITEM OF WORK (ALL FITTINGS AND FIXTURES SHOULD BE OF ALUMINIUM, ISI MARK, GOT APPROVED BY THE ENGINEER-IN-CHARGE). (APSS NO: 1001 &1002)

PROVIDING AND FIXING FACTORY MADE UPVC WHITE COLOUR FIXED GLAZED WINDOWS / VENTILATORS COMPRISING OF UPVC MULTI CHAMBERED FRAME ANDMULLION (WHERE EVER REQUIRED) EXTRUDED PROFILES DULY REINFORCED WITH 1.60± 0.2 MM THICK GALVANIZED MILD STEEL SECTION MADE FROM ROLL FORMING PROCESS OF REQUIRED LENGTH (SHAPE & SIZE ACCORDING TO UPVCPROFILE),UPVC EXTRUDED GLAZING BEADS OF APPROPRIATE DIMENSION, EPDM GASKET,G.I FASTENERS 100 X 8 MM SIZE FOR FIXING FRAME TO FINISHED WALL, PLASTICPACKERS, PLASTIC CAPS AND NECESSARY STAINLESS STEEL SCREWS ETC. PROFILEOF FRAME SHALL BE MITRED CUT AND FUSION WELDED AT ALL CORNERS, MULLION (IFREQUIRED) SHALL BE ALSO FUSION WELDED INCLUDING DRILLING OF HOLES FOR FIXINGHARDWARE'S AND DRAINAGE OF WATER ETC. AFTERFIXING FRAME THE GAP BETWEENFRAME AND ADJACENT FINISHED WALL SHALL BE FILLED WITH WEATHER PROOF SILICONSEALANT OVER BACKER ROD OF REQUIRED SIZE AND OF APPROVED QUALITY, ALLCOMPLETE AS PER APPROVED DRAWING & DIRECTION OF ENGINEER-IN-CHARGE INCLUSIVE OF COST OF SINGLE / DOUBLE GLASS PANES AND SILICON SEALANT.FIXED WINDOWS / VENTILATORS MADE OF (SMALL SERIES) FRAME 47 X 50MM & MULLION 47 X 68 MM BOTH HAVING WALL THICKNESS OF 1.9 ±0.2 MM AND SINGLE GLAZING BEAD OF APPROPRIATE DIMENSION

FLOORING WITH NON-SKID CERAMIC FLOOR TILES OF SIZE 300 X 300 MM AND THICKNESS BETWEEN 7-8 MM 1ST QUALITY CONFORMING TO IS:13711, IS:13712, IS:13630 (PARTS 1 TO 15) OF ANY COLOUR AND FINISH IN ALL SHADES AND DESIGNS, SET OVER BASE COAT OF CEMENT MORTAR (1:8), 12 MM THICK OVER CC BED ALREADY LAID OR RCC ROOF SLAB, INCLUDING NEAT CEMENT SLURRY OF HONEY LIKE CONSISTENCY SPREAD @ 3.3.KGS PER SQM & JOINTED NEATLY WITH WHITE CEMENT PASTE TO FULL DEPTH MIXED WITH PIGMENT OF MATCHING SHADE, INCLUDING COST OF ALL MATERIALS LIKE CEMENT, SAND WATER AND TILES ETC., BUT EXCLUDING SEIGNIORAGE CHARGES ETC., COMPLETE FOR FINISHED ITEM OF WORK. FOR GROUND FLOOR TOILETS.

PROVIDING DADOOING TO INTERNAL WALLS WITH DIGITAL / POLISHED GLAZED FULL BODY PORCELAIN WALL TILES OF SIZE 300 X 600 MM WITH ANY TYPE OF DESIGN TEXTURE SUCH AS MARBLE FINISH, WOODEN, BAMBOO, STONE FINISHES ETC., SCRATCH LESS, STAIN FREE AND THICKNESS BETWEEN 6 - 8 MM 1ST QUALITY CONFORMING TO IS:13711, IS:13712, IS:13630 (PARTS 1 TO 15) OF ANY COLOUR AND FINISH IN ALL SHADES AND DESIGNS, SET OVER BASE COAT OF CM (1:3) 12 MM THICK WITH CEMENT SLURRY OF HONEY LIKE CONSISTENCY SPREAD AT THE RATE OF 3.30 KGS PER SQM AND JOINTED WITH WHITE CEMENT PASTE MIXED WITH PIGMENT OF MATCHING SHADE TO FULL DEPTH, INCLUDING COST OF ALL MATERIALS LIKE TILES, CEMENT, SAND AND WATER ETC., COMPLETE EXCLUDING SEIGNIORAGE CHARGES, ETC., COMPLETE FOR FINISHED ITEM OF WORK, - GROUND FLOOR

PAINTING TO NEW WALLS WITH 2 COATS OF PLASTIC EMULSION PAINT OF APPROVED BRAND AND SHADE OVER A BASE COAT OF APPROPRIATE PRIMER OF APPROVED BRAND, MAKING 3 COATS IN ALL TO GIVE AN EVEN SHADE AFTER THOURUGHLY BRUSHING THE SURFACE TO REMOVE ALL DIRT AND REMAINS OF LOOSE POWDERED MATERIALS, INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO WORK SITE AND ALL OPERATIONAL, INCIDENTAL, LABOUR CHARGES ETC. COMPLETE FOR FINISHED ITEM OF WORK AS PER SS 911 FOR INTERNAL WALLS

PAINTING TO EXTERIOR FACES OF WALLS WITH EMULSION PAINT OF APPROVED MAKE (ACE FROM ASIAN PAINT) AND COLOUR 2 COATS BY DILUTING 1LIT OF EMULSION PAINT WITH A MAXIMUM 750 ML OF WATER WITHIN AN INTERVAL OF NOT LESS THAN 6 HOURS BETWEEN TWO COATS OVER 1 COAT OF ASIAN EXTERIOR WALL PRIMER BY DILUTING 1LIT. OF PRIMER WITH 1LIT. OF WATER (TOTAL 3 COATS) WITH SURFACE PREPARATION ETC., AS PER STANDARD SPECIFICATION INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, BRUSHES, ALL INCIDENTAL, OPERATIONAL & LABOUR CHARGES, CURING, SCAFFOLDING ETC., COMPLETE FOR FINISHED ITEM OF WORK. ALL FLOORS (APSS NO:908)

PAINTING TO NEW IRON WORK TWO COATS WITH SYNTHETIC ENAMEL PAINT OF APPROVED BRAND AND SHADE OVER ONE COAT OF RED OXIDE PRIMER COAT (TOTAL 3 COATS) INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, ALL INCIDENTAL, OPERATIONAL & LABOUR CHARGES FOR PREPARING AND CLEANING THE SURFACE OF DIRT WITH SOAP AND BRUSHES, INCLUDING PUTTY, ETC., COMPLETE FOR FINISHED ITEM OF WORK. (APSS NO.1201, 1207, 1212).

PROVIDING ROOFING WITH 0.50 MM THICK GALVANIZED / PRE-PAINTED G.I PROFILED SHEETS FIXED TO THE PURLINS WITH 14 SIZE SELF DRILLING SCREWS WITH NEOPRENE WASHER. SIDE LAPS ARE STICHED WITH SELF TAPPING / DRILLING SCREWS. END LAPS ARE TO BE SEALED WITH 25 X 3 MM BUTYL TAPE. THE SHEETS ARE PROVIDED WITH ANTI CAPILLARY GROVE INCLUDING ALL INCIDENTAL & OPERATIONAL CHARGES COST AND CONVEYANCE OF ALL MATERIALS TO SITE ETC., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND FIXING MS GRILLS FOR WINDOWS/VENTILATORS OF ALL SIZES AS DIRECTED BY THE ENGINEER-IN- CHARGE INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE AND LABOUR CHARGES FOR FABRICATION, FIXING ETC., COMPLETE FOR THE FINISHED ITEM OF WORK M.S. TUBES OF ALL SIZES FOR HEAD ROOM PURLINS

PROVIDING "HYSD" STEEL BARS OF DIFFERENT DIAMETERS BELOW 36MM DIAMETER (Fe - 500 GRADE AS PER IS 1786 - 1979)FOR REINFORCEMENT INCLUDING CUTTING, BENDING TO REQUIRED SIZES AND SHAPES, PLACING THEM IN POSITION WITH COVER BLOCKS OF APPROVED SHAPE AND SIZE, TYING FIRMLY WITH M.S BINDING WIRE OF SWG, FORMING GRILLS FOR REINFORCEMENT WORKS AS PER APPROVED DESIGNS AND DRAWINGS TO BE SUPPLIED AT THE TIME OF EXECUTION OF WORK INCLUDING COST AND CONVEYANCE OF DEFORMED BARS, BINDING WIRE, COVER BLOCKS AND ALL WASTAGES SUCH AS OVER LAPS, COUPLINGS, WELDED JOINTS, CHAIRS, SPACE BARS ETC., AS DIRECTED BY THE ENGINEER-IN-CHARGE AND ALL OPERATIONAL, INCIDENTAL LABOUR CHARGES SUCH AS CUTTING, BENDING, PLACING IN POSITION, TYING ETC., COMPLETE FOR FINISHED ITEM OF WORK FOR ALL LENGTHS AS PER DRAWINGS AND TECHNICAL SPECIFICATIONS FOR BARS BELOW 36MM DIA WHERE THEY ARE NOT WELDED.

SUPPLY AND LAYING OF ASHIRVAD / AJAY / ASTRAL FLOW GUARD OR EQUIVALENT CPVC PIPES AND FITTINGS TO MEET THE REQUIREMENT OF ASTM-D 2846 AND ARE PRODUCED IN CTS (COPPER TUBE SIZES 1/2" TO 2") ASHIRWAD FLOWGUARD SDR 13.5 PIPES ARE MADE FROM IDENTICAL CPVC COMPOUNDS HAVING THE SAME PHYSICAL PROPERTIES FOR HOT AND COLD WATER (IS 15778-2007) - 22.20 MM OD PIPES SDR 13.5

SUPPLY AND LAYING OF ASHIRVAD / AJAY / ASTRAL FLOW GUARD OR EQUIVALENT CPVC PIPES AND FITTINGS TO MEET THE REQUIREMENT OF ASTM-D 2846 AND ARE PRODUCED IN CTS (COPPER TUBE SIZES 1/2" TO 2") ASHIRWAD FLOWGUARD SDR 13.5 PIPES ARE MADE FROM IDENTICAL CPVC COMPOUNDS HAVING THE SAME PHYSICAL PROPERTIES FOR HOT AND COLD WATER (IS 15778-2007) - 28.60 MM OD PIPES SDR 13.5

SUPPLYING, LAYING, JOINTING AND TESTING OF SINGLE SOCKET 110 MM DIA PVC / SWR PIPES OF APPROVED MAKE OF 4 Kg/cm2 CONFIRMING TO IS:13592-1992, AND LABOUR CHARGES FOR LAYING, FIXING, AND COMMISSIONING THE PVC PIPES INCLUDING COUPLERS/ BENDS/TEES ETC., INCLUDING FIXING NECCESSARY FITTINGS LIKE BENDS PLUGS, COUPLERS, JUNCTIONS, TEES ETC., WITH SOLVENT JOINTING AS PER STANDARDS INCLUDING EXCAVATION OF TRENCHES AND SOCKET PITS IN ANY SOIL (EXCEPT ROCK REQUIRING BLASTING) UP TO 0.91M DEPTH AND REFILLING WITH EXCAVATED SOILS, WATERING, TAMPING, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND LAYING 110 MM DIA SINGLE SOCKET PVC / SWR PIPES OF APPROVED MAKE OF 4 Kg/cm2 CONFIRMING TO IS:13592-1992, WITH NECESSARY UPVC PIPE CLIPS @ 5' INTERVALS AND LABOUR CHARGES FOR LAYING, FIXING, AND COMMISSIONING THE PVC PIPES INCLUDING COUPLERS/ BENDS/TEES ETC., INCLUDING FIXING NECCESSARY FITTINGS LIKE BENDS, PLUGS, COUPLERS, JUNCTIONS, TEES ETC., WITH SOLVENT JOINTING AS PER STANDARDS INCLUDING CUTTING OF WALLS AND FLOORS AND MAKING THE SAME GOOD, INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND LAYING 75 MM DIA SINGLE SOCKET PVC / SWR PIPES OF APPROVED MAKE OF 4 Kg/cm2 CONFIRMING TO IS:13592-1992, WITH NECESSARY UPVC PIPE CLIPS @ 5' INTERVALS AND LABOUR CHARGES FOR LAYING, FIXING, AND COMMISSIONING THE PVC PIPES INCLUDING COUPLERS/ BENDS/TEES ETC., INCLUDING FIXING NECCESSARY FITTINGS LIKE BENDS, PLUGS, COUPLERS, JUNCTIONS, TEES ETC., WITH SOLVENT JOINTING AS PER STANDARDS INCLUDING CUTTING OF WALLS AND FLOORS AND MAKING THE SAME GOOD, INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND FIXING 15 MM DIA BIB TAP WITH FLANGE CHROMIUM PLATED JAQUAR MAKE QUEEN SERIES INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR ETC., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND FIXING 12.70 MM DIA ANGLE STOP COCK (400 GRAMS)INDIAN MAKE, HEAVY DUTY OF APPROVED ISI BRAND INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR ETC., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND FIXING 20 MM NB SIZE GM GATE(PEET) VALVE AS PER IS - 778, CLASS-I, INDIAN MAKE HEAVY TYPE, INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR ETC., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND FIXING 25 MM NB SIZE GM GATE(PEET) VALVE AS PER IS - 778, CLASS-I, INDIAN MAKE HEAVY TYPE, INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR ETC., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND FIXING 19.04 MM DIA, 609.60 MM LONG C.P TOWEL ROD WITH BRACKETS AND SCREWS INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., FOR FINISHED ITEM OF WORK COMPLETE.

SUPPLYING AND FIXING NP SOAP DISH HEAVY TYPE WITH NP SCREWS INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC.,COMPLETE FOR FINISHED ITEM OF WORK.

CONSTRUCTING 457.20 X 457.20 MM (1'-6" X 1'-6") BRICK MASONARY INSPECTION CHAMBER WITH CM (1:6) PROP. USING 2ND CLASS CLAY BRICKS OF 225MM THICK , AND FITTED WITH 457.2 X 457.2 MM (1'-6" X 1'-6") RCC COVER UP TO A DEPTH OF 914.4 MM (3'-0") AND LAYING CEMENT CONCRETE (1:4:8) 150 MM THICK USING 40 MM HBG METAL AND PCC (1:2:4) BENCHING AND CHANNEL 100 MM THICK AS PER STANDARD SPECIFICATION FOR FINISHED ITEM OF WORK.

SUPPLY AND FIXING IN POSITION EUROPEAN TYPE WATER CLOSET OF BEST INDIAN MAKE WHITE GLAZED WITH 100 MM 'P' TRAP, PLASTIC SEAT AND LID FOR EUROPEAN WATER CLOSET AND BUFFERS AS PER IS 2548-1963 AND PROVIDING PVC LOW LEVEL FLUSHING SYSTEM OF 8 LITRES CAPACITYOF PARRYWARE SLIMLINE (WHITE) WITH INTERNAL COMPONENTS AND SHORT BEND, 12.70 MM PVC CONNECTION WITH BRASS UNION NUTS C.P COATED, INCLUDING CUTTING THE WALLS AND FLOORS AND MAKING GOOD THE SAME, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., COMPLETE.

SUPPLYING AND FIXING INDIAN MAKE FLAT BACK WHITE GLAZED WASH HAND BASIN (HSW/PARRYWARE/NEYCER) IST QUALITY CONFIRMING TO IS: 2556-PART-4 :1972 OF SIZE 550 X 400MM SINGLE C.P. PILLAR COCK AS APPROVED BY EXECUTIVE ENGINEER WITH WASTE FITTINGS LIKE RUBBER PLUG, CHAIN, 32MM NOMINAL SIZE C.P. FITTING WITH PARALLEL PIPE THREAD CONFIRMING TO IS : 2963-1979 AND FITTED WITH 15MM NOMINAL BORE CHROMIUM PLATED PILLAR TAP OF 1ST QUALITY INDIAN MAKE 400GRAMS SEICO/SENIOR/NICE/ESSO OR EQUIVALENT COMPLETE WITH STANDARD CI BRACKETS, AND PAINTING TO ALL IRON FITTINGS WITH 2 COATS OF SYNTHETIC ENAMEL PAINT OF APPROVED COLOUR AND MAKE INCLUDING CUTTING THE WALLS WHEREVER NECESSARY AND MAKING THE SAME GOOD FOR FINISHED ITEM OF WORK. INCLUDING WOODEN BLOCK INCLUDING CUTTING THE WALLS WHEREVER NECESSARY AND MAKING THE SAME GOOD FOR FINISHED ITEM OF WORK

SUPPLYING & FIXING WHITE GLAZED FLAT BACK HALF STALL URINALS 1ST QUALITY CONFORMING TO IS:2556-1995 WITH STANDARD C.P. SPREADER OF OVERALL SIZE 95 X 95 X 57 MM CONFORMING TO IS:2556-PART6, SEC-6-1974 FIXED WITH SCREWS COMPLETE INDIAN MAKE (HSW/PARRY/NEYCER) : 590 X 375 X 390 MMINCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR ETC., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND FIXING BEST INDIAN MAKE 609.6X457.2mm T.V SHAPE MIRROR WITH PLASTIC FRAME MIRROR INCLUDING WOODEN BLOCKS, SCREWS ETC., INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., FOR FINISHED ITEM OF WORK COMPLETE.

SUPPLYING AND FIXING BIBCOCK CUM HEALTH FAUCET WITH 1 M LONG TUBE AND WALL HOOK OF JAQUAR QUEEN SERIES, CHROME FINISH INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR ETC., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND FIXING OF 16MM TO 20 MM THICK POLISHED BLACK GRANITE PARTITIOINS OF SIZE 4' 0" X 2' 0" FOR URINALS INCLUDING FULL ROUNDING THE EDGES , FIXING IN POSITION, POLISHING, INCLUDING COST AND CONVEYANCE OF ALL MATERIALS AND LABOUR CHARGES , OVERHEADS & CONTRACTORS PROFIT COMPLETE FOR FINISHED ITEM OF WORK FOR ALL FLOORS.

SUPPLY AND LAYING OF ASHIRVAD / AJAY / ASTRAL FLOW GUARD OR EQUIVALENT CPVC PIPES AND FITTINGS TO MEET THE REQUIREMENT OF ASTM-D 2846 AND ARE PRODUCED IN CTS (COPPER TUBE SIZES 1/2" TO 2") ASHIRWAD FLOWGUARD SDR 13.5 PIPES ARE MADE FROM IDENTICAL CPVC COMPOUNDS HAVING THE SAME PHYSICAL PROPERTIES FOR HOT AND COLD WATER (IS 15778-2007) - 41.30 MM OD PIPES SDR 13.5

SUPPLYING AND FIXING 40MM NB SIZE GM GATE(PEET) VALVE AS PER IS - 778, CLASS-I, INDIAN MAKE HEAVY TYPE, INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR ETC., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND FIXING 40 MM NB SIZE GM HORIZONTAL CHECK (NON RETURN) VALVE AS PER IS - 778, CLASS-I, INDIAN MAKE HEAVY TYPE, INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR ETC., COMPLETE FOR FINISHED ITEM OF WORK.

PROVIDING AND PLACING ON TERRACE POLYTHELENE WATER STORAGE TANKS (AT ALL FLOOR LEVELS) DOUBLE LAYER APPROVED BRAND AND MNUFACTURE WITH COVER AND SUITABLE LOCKING ARRANGEMENTS MAKING NECESSARY HOLES FOR INLET & OUTLETS AND OVERFLOW PIPES BUT WITHOUT FITTINGS & BASE SUPPORT FOR TANKS, MAKING GOOD THE SAME TO ENSURE LEAK PROOF WITH AN APPROPRIATE MASONARY PLATFORM INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR ETC.,COMPLETE FOR FINISHED ITEM OF WORK AS DIRECTED BY THE ENGINEER -IN- CHARGE.

SUPPLY AND LAYING OF ASHIRVAD / AJAY / ASTRAL FLOW GUARD OR EQUIVALENT CPVC PIPES AND FITTINGS TO MEET THE REQUIREMENT OF ASTM-D 2846 AND ARE PRODUCED IN CTS (COPPER TUBE SIZES 1/2" TO 2") ASHIRWAD FLOWGUARD SDR 13.5 PIPES ARE MADE FROM IDENTICAL CPVC COMPOUNDS HAVING THE SAME PHYSICAL PROPERTIES FOR HOT AND COLD WATER (IS 15778-2007) - 41.30 MM OD PIPES SDR 13.5

SUPPLYING AND FIXING 40MM NB SIZE GM GATE(PEET) VALVE AS PER IS - 778, CLASS-I, INDIAN MAKE HEAVY TYPE, INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR ETC., COMPLETE FOR FINISHED ITEM OF WORK.

Supply and fixing of 16/20A 1 way modular switch-1 no with 20A modular socket -1no and 6/10AA 3/2 pin modular plug socket - 3 nos with 6A 1 way modular switch - 3 nos with 12 Module box size covered with 12 module cover frame including earth connections and all labour charges etc., complete.(For computer switch board) Make: Legrand (Myrius/Lyncus) / Schneider (Clipsal X/ Livia AB)/ Crabtree (Murano/ Athena) / Lauritz Knudsen - englaze ( Formerly L&T) / Honeywell (Blenzero). (for UPS)

Supply and run of 1 of 14 /0.3mm (1.0 Sq.mm) FRLS / HFFR/ZHFR P.V.C. insulated 1100V grade as perIS:694/1990 specification for insulated flexible copper cable in existing pipe for earth continuity including all labour charges etc., complete. [for Earth lead to circuit mains, power sockets]. Make: Finolex/RR kabel/Havells / FortuneArrt

Supply and run of 3 of 36 /0.3mm (2.5 Sq.mm) FRLS / HFFR/ZHFR P.V.C. insulated 1100V grade as perIS:694/1990 specification for insulated flexible copper cable in existing pipe for run of circuits, power plugs & computer boards including all labour charges etc., complete. ( For Phase Neutral and Earth) ( Circuit Mains to Switch Board) Make:Finolex/RR kabel/Havells / FortuneArrt

SUPPLY OF 48" (1200MM) SWEEP , 5 STAR RATED CEILING FAN, WITH DOUBLE BALL BEARINGS , POWER INPUT NOT MORE THAN 53W , AIR DELIVERY MORE THAN 218 CUBIC METER/MIN AND SERVICE VALUE 4.11, BUT WITHOUT REGULATOR INCLUDING COST AND CONVEYANCE OF ALL MATERIALS ETC. COMPLETE. MAKE: CROMPTON / ORIENT.

SUPPLY OF 400W STEPPED TYPE ELECTRONIC REGULATOR INCLUDING COST AND CONVEYANCE OF MATERIALS AND LABOUR CHARGES ETC., COMPLETE. MAKE: LEGRAND ARTEOR/CARBTREE MURANO/GM-ZENOV.

LABOUR CHARGES FOR FIXING OF CEILING FAN AND REGULATOR INCLUDING TRANSPORTATION AND GIVING CONNECTIONS WITH TWIN CORE WIRE ETC., COMPLETE.

SUPPLY AND TRANSPORTATION OF 18W, 1800 LUMENS,T8,1200MM LENGTH LED BATTEN TYPE TUBE LIGHT, INPUT VOLTAGE AC 220 - 260 VOLTS WITH PF>0.9, SURGE PROTECTION: KV,THD<15%, WITH INBUILT DRIVER AND FROSTED COVER CCT: 3000K - 5700K, MINIMUM CRI>70, .ETC., COMPLETE MAKES: PHILLIPS / GE / CROMPTON.

FIXING OF 18W LED TUBE LIGHT LUMINAIRE ON WALL / CEILING WITH ALL ACCESSORIES INCLUDING GIVING CONNECTIONS AND ALL LABOUR CHARGES ETC., COMPLETE.

SUPPLY OF FRESH AIR EXHAUST FAN OF LIGHT DUTY 250V A.C.50HZ../ 300MM SIZE (12") 1350 R.P.M METALLIC BODY PLASTIC BLADES, WIRE MESH, ETC., COMPLETE. MAKE CROMPTON/ORIENT.

LABOUR CHARGES FOR FIXING OF EXHAUST FAN IN WALL WITH NECESSARY CONNECTIONS AND MASONARY WORK OF MAKING HOLE, FINISHING ETC., COMPLETE.

Supply and fixing of batten holder / slanting holder in lieu of ceiling rose of light point complete with all connections and all labour charges with 7W LED, 490Lumens bulb (for new installation). Holder Make: Anchor / Gold Medal Olive / Million Zoom LAMP Make:Phillips / OSRAM / GE / Crompton.

SUPPLY AND FIXING OF 18 W LED SLIM PANEL ROUND /SQUARE SUITABLE FOR RECESSED / SURFACE MOUNTING MADE OF DIECAST ALLUMINIUM BODY WITH POWDER COATING, ACRYLIC DIFFUSER WITH DRIVER AS PER IS: 15885 (PART 2/ SEC 13) : 2012 , OPERATING VOLTAGE-VENTURE RANGE-VENTURE OF 150 TO 265 VOLTS AC, P.F > 0.9, SURGE-VENTURE PROTECTION: 2KV,THD<10%, WITH HIGH POWER LED'S HAVING EFFICACY OF > 100 LUMINS/WATT,CCT: 3000K - 5700K, MINIMUM CRI>70, .ETC., COMPLETE A) LUMINAIRE MAKE : PHILLIPS / GE-VENTURE / CROMPTON / WIPRO / BAJAJ / HAVELLS / HALONIX/JAQUAR/HPL/GM / GREENLITES / GOLD MEDAL/EVEREADY/ FORTUNEARRT B) LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM / SAMSUNG/EVERLIGHT.[ELEC-3.8.4 (E)]

FIXING OF LED LUMINAIRE DOWN LIGHT FITTING WITH ALL NECESSARY ACCESSORIES IN FALSE CEILING/ POP CUTTING / ON WALL INCLUDING GIVING CONNECTIONS AND ALL LABOUR CHARGES ETC., COMPLETE.

Supply and fixing Distribution board with 20A single phase plug and Socket, in sheet steel enclosure with 10/16/20A SP MCB including internal connection and labour charges for surface / flush mounting etc., complete. Make: Legrand(Ekinox 3) / Schneider-Acti9 / Havells/Indo Asain

Supply and fixing 4way TPN D.B with board with IP-43 protection suitable for three phase 40A FP MCB - 1 No for incomer, 10kA-6-32A SP MCBs - 12 Nos for outgoing. including internal connection and labour charges for surface / flush mounting etc., complete.(for LDB) Make: Legrand(Ekinox 3) / Schneider-Acti9 / Seimens /L&T Newrang

SUPPLY AND FIXING 6 WAY TPN - VERTICAL TYPE DISTRIBUTION BOARD WITH IP -43 PROTECTION (METAL DOOR) WITH 125A, 4POLE 25 KA MCCB AS INCOMER WITH 4NOS 63A TP MCBS,6NOS 32A RANGE SP MCBS AS OUTGOING INCLUDING INTERNAL CONNECTION AND LABOUR CHARGES FOR SURFACE / FLUSH MOUNTING ETC., COMPLETE.

Supply and transportation of 20W LED Street light Luminaire made of pressure diecast alluminium body with powder coated, having protective toughned glass, Supply Input voltage 120 - 270 V AC, P.F > 0.90, high power LED's having System efficacy > 110 lm/W and junction temprature < 70°C, with Ingrees protection IP66, Luminaire performance complies to IS 10322 (Part 5 / Sec-3), Driver surge protection 4KV, external Surge protection 10 KV with optics distribution , THD<10% at 110 Volts AC, driver efficiency >90%, CCT: 3000K - 5700K, minimum CRI>70, etc., complete MAKE : Philips (Green line) / GEVenture/ Crompton(Hawk) / Bajaj (Edge+)

Fixing of LED street light luminary with 1.0 Mtr., 25mm dia GI pipe bracket and anti tilting MS flat etc., including giving connections and labour charges etc., complete.

Supply and transportation of 100W LED Flood light Luminaire made of pressure diecast alluminium housing with powder coated,having protective toughned glass,Supply Input voltage 120 - 270 V AC, P.F > 0.90, high power LED's System efficacy >100lm/W and junction temprature < 70°C, with Ingrees protection IP66, Luminaire performance complies to IS 10322 (Part 5 / Sec-3), IK05, Driver surge protection 4KV, external Surge protection ≥ 10KV with wide/ Narrow beam optics, THD<10% at 110 Volts AC, driver efficiency >90%, , CCT: 3000K - 5700K, minimum CRI>70, etc., complete. MAKE : Wipro / Philips/ GE-Venture / Crompton/ Bajaj

Fixing of LED flood luminaire on wall with 3Cx 2.5 Sq.mm flexible copper cable etc.,including all labour charges for mason work and giving connections etc., complete.

Providing independent earthing for Important equipment with 40mm dia 'B' class 2.5m long G.I pipe and 19mm dia 'B' class G.I pipe of 0.3mtr. long connected with reducer providing G.I funnel with mesh enclosed in C.C.Chamber of 400m x 400m x 400mm with R.C.C. Slab cover duly providing staggered holes filling with salt and charcoal from the bottom of the pipe giving earth connection from electrode through G.I strip of 25 x 6mm x 200mm length with all accessories and labour charges complete, as per IS specifications 732/1982 (Part II)

SUPPLY & FIXING OF PEETA BOARD OF SIZE 24" X 18" INCLUDING ALL LABOUR CHARGES ETC,. COMPLETE.

Supply of 63A 415 V Porcelain Rewirable Fuse Units with extension strip. Makes: C&S/Standard/HPL/ Sputnik / Million / Gold Medal / Benlo/Anchor

Supply & fixing of 16 Sqmm 4.0 Core XLPE insulated, 1100V grade armoured alluminium cable as per specification confirming to IS:7098 (Part - I) Makes: Torent / Universal / Unicab / Havells / KEI / Gloster / Polycab /RR Kabel