Bhavnagar Division - Providing 18 units type-II quarters on Replacement Account at Gop-Jam and Lalpur Jam

A-DSR 2023 items

B-Electrical items

Item Breakup - A-DSR 2023 items

nuts complete. Providing and fixing chromium plated brass 9.92 handles with necessary screws etc. complete: 60 9.92.1 125 mm Each 36 231.05 8317.8 61 9.92.2 100 mm Each 36 206.25 7425 ANODISED ALUMINIUM FITTINGS (ALL 9.95S FITTINGS SHALL BE ISI MARKED) Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating 9.96 not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 62 9.96.2 250x16 mm Each 60 260.6 15636 BHAVNAGAR DIVISION-ENGG/WESTERN RLY Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) 9.97 transparent or dyed to required colour or shade, with necessary screws etc. complete : 63 9.97.1 300x10 mm Each 30 130.1 3903 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) 9.100 transparent or dyed to required colour or shade, with necessary screws etc. complete : 64 9.100.1 125 mm Each 60 66.25 3975 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 9.101 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. 65 9.101.1 Single rubber stopper Each 20 39.6 792 9.105S GYPSUM BOARD PARTITIONS 9.119 Providing and fixing factory made P.V.C. Metre 120 492.7 59124 door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be 66 reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer's specification and direction of Engineer- in-Charge. BHAVNAGAR DIVISION-ENGG/WESTERN RLY Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm 9.120 shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, panelling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing. 67 9.120.1 30 mm thick plain PVC door shutters Sqm 54 3182.95 171879.3 9.121 Providing and fixing Fiber Glass Reinforced Metre 180 570.95 102771 plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade 68 unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame. 9.122 Providing and fixing to existing door frames. 9.122.1 30 mm thick Glass Fibre Reinforced Plastic Sqm 84.6 3720.75 314775.45 (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming 69 hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames. 10.0 STEEL WORK 10.1S General 10.1 Structural steel work in single section, fixed Kg 1560 117.35 183066 with or without connecting plate, including 70 cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. BHAVNAGAR DIVISION-ENGG/WESTERN RLY 10.2 Structural steel work riveted, bolted or Kg 1260 133.7 168462 welded in built up sections, trusses and 71 framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 10.17 Providing and fixing M.S. fan clamp type I or Each 54 226 12204 II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams 72 during laying, including painting the exposed portion of loop, all as per standard design complete. Steel work welded in built up sections/ framed work, including cutting, hoisting, 10.25 fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 10.25.2 In gratings, frames, guard bar, ladder, Kg 3620 172.6 624812 73 railings, brackets, gates and similar works 10.28 Providing and fixing stainless steel ( Grade Kg 1850 772.4 1428940 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & 74 stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). 11.0 FLOORING 11.1S General Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) 11.3 finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 11.3.1 40 mm thick with 20 mm nominal size Sqm 800 614.2 491360 75 stone aggregate 11.16S TILE FLOORING Chequered terrazzo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry 11.19 mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : 76 11.19.4 Ordinary cement without any pigment Sqm 12.6 1379 17375.4 11.26S KOTA STONE FLOORING Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with 11.26 pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 77 11.26.1 25 mm thick Sqm 240 1948.25 467580 BHAVNAGAR DIVISION-ENGG/WESTERN RLY 11.27 Kota stone slabs 20 mm thick in risers of Sqm 124 2354.7 291982.8 steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 78 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 11.37S CERAMIC GLAZED TILES 11.37 Providing and laying Ceramic glazed floor Sqm 804 1096.55 881626.2 tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, 79 Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 11.37A Providing and fixing 1st quality ceramic Sqm 280 1112.7 311556 glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by 80 Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. 11.41S VITRIFIED FLOOR TILES Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and 11.41 shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 81 11.41.2 Size of Tile 600x600 mm Sqm 984 1553.45 1528594.8 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in 11.46 skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. 82 11.46.2 Size of Tile 600x600 mm Sqm 460 1623.05 746603 12.0 ROOFING 12.37S RAIN WATER SPOUT AND PIPE Providing and fixing M.S. holder bat clamps of approved design to C.I. or S.C.I. rain water pipes embedded in and including cement concrete blocks 10x10x10 cm of 12.38 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the walls etc. : 83 12.38.1 100 mm diameter Each 20 362.85 7257 BHAVNAGAR DIVISION-ENGG/WESTERN RLY Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including 12.41 jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 84 12.41.1 75 mm diameter Metre 10 248.8 2488 85 12.41.2 110 mm diameter Metre 130 377.4 49062 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain 12.42 water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 12.42.1 Coupler 86 12.42.1.1 75 mm Each 12 91.7 1100.4 87 12.42.1.2 110 mm Each 30 136.15 4084.5 12.42.5 Bend 87.5 degree 88 12.42.5.2 110 mm bend Each 120 150.35 18042 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. 12.43 screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 89 12.43.1 75 mm Each 30 369.85 11095.5 90 12.43.2 110 mm Each 45 371.3 16708.5 Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8 mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel 12.47 rovings incorporating minimum 0.3% ultra- violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 91 12.47.2 2 mm thick flat Sqm 60 1245.65 74739 BHAVNAGAR DIVISION-ENGG/WESTERN RLY 12.50 Providing and fixing precoated galvanised Sqm 12.64 738.65 9336.54 iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in- charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective 92 guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc 12.51 coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : 93 12.51.1 Ridges plain (500 - 600mm) Metre 24 532.35 12776.4 13.0 FINISHING 13.1S CEMENT PLASTER (IN FINE SAND) 13.1 12 mm cement plaster of mix : 94 13.1.2 1:6 (1 cement: 6 fine sand) Sqm 4506.77 333.35 1502331.78 CEMENT PLASTER WITH A FLOATING COAT 13.7S OF NEAT CEMENT 12 mm cement plaster finished with a 13.7 floating coat of neat cement of mix : 95 13.7.2 1:4 (1 cement: 4 fine sand) Sqm 236 425.55 100429.8 13.11S CEMENT PLASTER IN TWO COATS 13.11 18 mm cement plaster in two coats under Sqm 3260 518.55 1690473 layer 12 mm thick cement plaster1:5 (1 96 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand). 13.16S 6 mm CEMENT PLASTER 13.16 6 mm cement plaster of mix : 97 13.16.1 1:3 (1 cement : 3 fine sand) Sqm 840 300.45 252378 13.20S PEBBLE DASH PLASTER 13.26 Providing and applying plaster of paris Sqm 4506.77 262.7 1183928.48 putty of 2 mm thickness over plastered 98 surface to prepare the surface even and smooth complete. 13.37S INTERIOR FINISHING Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved 13.41 manufacturer and of required shade and colour all complete to achieve even shade and colour : BHAVNAGAR DIVISION-ENGG/WESTERN RLY 13.41.1 New work (two or more coats) over and Sqm 120.3 185.65 22333.7 including water thinnable priming coat with 99 cement primer having VOC content less than 50 gram/litre 13.44S EXTERIOR FINISHING Finishing walls with Acrylic Smooth exterior 13.46 paint of required shade : 13.46.1 New work (Two or more coat applied @ Sqm 120.3 160.6 19320.18 1.67 ltr/10 sqm over and including priming 100 coat of exterior primer applied @ 0.90 litre/10 sqm) Finishing with Deluxe Multi surface paint 13.48 system for interiors and exteriors using Primer as per manufacturers specifications : 13.48.1 Two or more coats applied on walls @ 1.25 Sqm 4506.77 193.7 872961.35 101 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm 13.50 Applying priming coat: 13.50.2 With ready mixed aluminium primer of Sqm 1250 74.65 93312.5 102 approved brand and manufacture on resinous wood and plywood Painting with synthetic enamel paint of 13.61 approved brand and manufacture to give an even shade : 103 13.61.1 Two or more coats on new work Sqm 840 155.9 130956 13.80 Providing and applying white cement based Sqm 236 156.05 36827.8 putty of average thickness 1 mm, of 104 approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of 13.82 approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. 105 13.82.2 Two coats Sqm 2929.4 137.45 402646.03 16.0 ROAD WORK 16.1S ROADS 16.3 Supplying and stacking at site. 106 16.3.1 90 mm to 45 mm size stone aggregate cum 150.36 2098.4 315515.42 107 16.3.2 63 mm to 45 mm size stone aggregate cum 140.6 1636.05 230028.63 108 16.3.10 Moorum cum 480.8 768.25 369374.6 16.4 Laying, spreading and compacting stone cum 771.76 1046.95 807994.13 aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in 109 stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density . 16.42S CONCRETE PAVEMENTS BHAVNAGAR DIVISION-ENGG/WESTERN RLY Providing and laying design mix cement concrete of M-30 grade, in roads/taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved and specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to 16.43 required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction and longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately). 16.43.1 Cement concrete prepared with batch cum 120.65 10529.35 1270366.08 110 mixing machine 16.49S MISCELLANEOUS 16.69 Providing and laying at or near ground level cum 8.2 10117.6 82964.32 factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except 111 at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured to calculate volume for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting 16.91 and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 16.91.1 60mm thick cement concrete paver block of Sqm 420 1045.65 439173 112 M-35 grade with approved colour, design & pattern. 17.0 SANITARY INSTALLATIONS 17.1S General BHAVNAGAR DIVISION-ENGG/WESTERN RLY Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush 17.1 pipe, with manually controlled device (handle lever) conforming to IS : 7231,with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 17.1.1 White Vitreous china Orissa pattern W.C. Each 18 6767.4 121813.2 113 pan of size 580x440 mm with integral type foot rests Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including 17.2 flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : 17.2.1 W.C. pan with ISI marked white solid plastic Each 18 6515.55 117279.9 114 seat and lid Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, 17.7 including painting of fittings and brackets, cutting and making good the walls wherever require: 17.7.2 White Vitreous China Wash basin size Each 36 2226.35 80148.6 115 630x450 mm with a single 15 mm C.P. brass pillar tap Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 17.10 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 17.10.2 Kitchen sink without drain board 116 17.10.2.2 610x460 mm bowl depth 200 mm Each 12 3873.8 46485.6 117 17.10.2.3 470x420 mm bowl depth 178 mm Each 8 3407.2 27257.6 17.22B Providing and fixing CP Brass Single lever Each 9 6940.75 62466.75 telephonic wall mixer of quality and make 118 as approved by Engineer in charge.(a) 15 mm nominal dia 17.23 Providing and fixing white vitreous china Each 2 1648.95 3297.9 flat back or wall corner type lipped front 119 urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively. Providing and fixing P.V.C. waste pipe for 17.28 sink or wash basin including P.V.C. waste fittings complete. 17.28.2 Flexible pipe 120 17.28.2.2 40 mm dia Each 40 119.55 4782 17.29 Providing and fixing 100 mm sand cast Iron Each 80 53.25 4260 121 grating for gully trap. 17.31 Providing and fixing 600x450 mm bevelled Each 36 1607.95 57886.2 edge mirror of superior glass (of approved 122 quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 17.34 Providing and fixing toilet paper holder : 123 17.34.1 C.P. brass Each 8 803.7 6429.6 Providing and fixing soil, waste and vent 17.35 pipes : 17.35.2 75 mm diameter : BHAVNAGAR DIVISION-ENGG/WESTERN RLY 124 17.35.2.1 Sand cast iron S&S pipe as per IS: 1729 Metre 25 1044.75 26118.75 Providing and fixing trap of self cleansing design with screwed down or hinged grating 17.60 with or without vent arm complete, including cost of cutting and making good the walls and floors : 17.60.2 100 mm inlet and 75 mm outlet 125 17.60.2.1 Sand cast iron S&S as per IS - 3989 Each 18 1975.15 35552.7 Providing and fixing PTMT Waste Coupling 17.69 for wash basin and sink, of approved quality and colour. 17.69.1 Waste coupling 31 mm dia of 79 mm length Each 40 115.3 4612 126 and 62mm breadth weighing not less than 45 gms Providing and fixing PTMT Bottle Trap for 17.70 Wash basin and sink. 17.70.1 Bottle trap 31mm single piece moulded Each 40 367.1 14684 with height of 270 mm, effective length of tail pipe 260 mm from the centre of the 127 waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms 17.71 Providing and fixing PTMT liquid soap Each 18 168.35 3030.3 container 109 mm wide, 125 mm high and 112 mm distance from wall of standard 128 shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. 17.72 Providing and fixing PTMT towel ring Each 18 231.95 4175.1 trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm 129 from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. Providing and fixing PTMT towel rail complete with brackets fixed to wooden 17.73 cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 17.73.2 600 mm long towel rail with total length of Each 18 708.95 12761.1

of 88 mm, weighing not less than 190 gms. 17.74 Providing and fixing PTMT shelf 440 mm Each 18 713.2 12837.6 long, 124 mm width and 36 mm height of 131 approved quality and colour, weighing not less than 300 gms. 17.81 Providing and fixing floor mounted, white Each 4 18212.9 72851.6 vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual 132 flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. 18.0 WATER SUPPLY 18.7S C.P.V.C. PIPES BHAVNAGAR DIVISION-ENGG/WESTERN RLY Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of 18.8 pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 133 18.8.1 15 mm nominal dia Pipes Metre 60 497.8 29868 134 18.8.2 20 mm nominal dia Pipes Metre 220 537.6 118272 135 18.8.3 25 mm nominal dia Pipes Metre 135 627.25 84678.75 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded 18.9 fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 136 18.9.1 15 mm nominal dia Pipes Metre 40 244.7 9788 137 18.9.2 20 mm nominal dia Pipes Metre 30 274.3 8229 138 18.9.3 25 mm nominal dia Pipes Metre 40 355.4 14216 139 18.9.5 40 mm nominal dia Pipes Metre 60 563.05 33783 140 18.9.6 50 mm nominal dia Pipes Metre 156 794.25 123903 141 18.9.8 80 mm nominal dia Pipes Metre 124.58 2166.35 269883.88 142 18.9.9 100 mm nominal dia Pipes Metre 152 3271.7 497298.4 Making connection of G.I. distribution branch with G.I. main of following sizes by 18.13 providing and fixing tee, including cutting and threading the pipe etc. complete : 143 18.13.1 25 to 40 mm nominal bore Each 18 911.9 16414.2 144 18.13.2 50 to 80 mm nominal bore Each 18 1785.35 32136.3 18.15S BRASS FITTINGS Providing and fixing brass bib cock of 18.15 approved quality : 145 18.15.1 15 mm nominal bore Each 18 353.25 6358.5 146 18.15.2 20 mm nominal bore Each 18 379.2 6825.6 Providing and fixing brass stop cock of 18.16 approved quality : 147 18.16.1 15 mm nominal bore Each 36 353.25 12717 Providing and fixing gun metal gate valve 18.17 with C.I. wheel of approved quality (screwed end) : 148 18.17.1 25 mm nominal bore Each 8 622.4 4979.2 149 18.17.3 40 mm nominal bore Each 8 826.1 6608.8 150 18.17.4 50 mm nominal bore Each 18 1026.65 18479.7 Providing and fixing ball valve (brass) of 18.18 approved quality, High or low pressure, with plastic floats complete : 151 18.18.1 15 mm nominal bore Each 8 406.85 3254.8 152 18.18.2 20 mm nominal bore Each 8 462.5 3700 153 18.18.3 25 mm nominal bore Each 8 464.05 3712.4 Providing and fixing gun metal non- return 18.19 valve of approved quality (screwed end) : 18.19.1 25 mm nominal bore 154 18.19.1.1 Horizontal Each 8 591.4 4731.2 BHAVNAGAR DIVISION-ENGG/WESTERN RLY Providing and fixing C.P. brass shower rose 18.22 with 15 or 20 mm inlet 155 18.22.1 100 mm diameter Each 20 193.95 3879 C.I. SLUICE VALVES/ FIRE HYDRANTS & 18.31S FIXTURES Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in reinforced cement concrete slab 1:1.5:3 mix (1 cement : 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size), 18.32 including necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand :10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : 18.32.1 With common burnt clay F.P.S.(non Each 12 1992.6 23911.2 156 modular) bricks of class designation 7.5 Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I.surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 18.33 mm nominal size ) including necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : 18.33.1 With common burnt clay F.P.S.(non Each 4 10862.4 43449.6 157 modular) bricks of class designation 7.5 Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I.surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 18.34 mm nominal size ), including necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : 18.34.1 With common burnt clay F.P.S.(non Each 8 18896.7 151173.6 158 modular) bricks of class designation 7.5 18.48 Providing and placing on terrace (at all floor Per Litre 36000 11 396000 levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable 159 locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 18.49S C.P. BRASS FITTINGS BHAVNAGAR DIVISION-ENGG/WESTERN RLY Providing and fixing C.P. brass bib cock of 18.49 approved quality conforming to IS:8931 : 160 18.49.1 15 mm nominal bore Each 18 506.8 9122.4 Providing and fixing C.P. brass long body bib cock of approved quality conforming to 18.51 IS standards and weighing not less than 690 gms. 161 18.51.1 15 mm nominal bore Each 36 798.95 28762.2 Providing and fixing C.P. brass stop cock 18.52 (concealed) of standard design and of approved make conforming to IS:8931. 162 18.52.1 15 mm nominal bore Each 18 670.45 12068.1 Providing and fixing C.P. brass angle valve 18.53 for basin mixer and geyser points of approved quality conforming to IS:8931 163 18.53.1 15mm nominal bore Each 18 574.3 10337.4 18.54S PTMT FITTINGS Providing and fixing PTMT bib cock of 18.54 approved quality and colour. 18.54.1 15 mm nominal bore, 86 mm long, Each 36 125.6 4521.6 164 weighing not less than 88 gms Providing and fixing PTMT stop cock of 18.55 approved quality and colour. 18.55.1 15 mm nominal bore, 86 mm long, Each 36 118.5 4266 165 weighing not less than 88 gms Providing and fixing PTMT pillar cock of 18.56 approved quality and colour. 18.56.1 15 mm nominal bore, 107 mm long, Each 18 208.45 3752.1 166 weighing not less than 110 gms 18.59S AIR VALVE & WATER METER (BULK TYPE) Providing and fixing PTMT Ball cock of approved quality, colour and make 18.62 complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. 18.62.1 15 mm nominal bore, 105 mm long, Each 20 182.1 3642 167 weighing not less than 138 gms 18.62.3 25 mm nominal bore, 152mm long, Each 20 523.8 10476 168 weighing not less than 440 gms 18.63 Providing and fixing PTMT angle stop cock Each 20 156.9 3138

than 85 gms 18.65 Providing and fixing PTMT soap Dish Holder Each 20 111.45 2229 having length of 138mm, breadth 102mm, 170 height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming to JWWA G116 standard with V- 18.90 profile or M-profile and with O-ring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge. Elbow 90 degree 171 18.90.2 For 22.22 mm outer dia pipe Each 4 113.8 455.2 172 18.90.3 For 28.58 mm outer dia pipe Each 4 163.6 654.4 173 18.90.6 For 48.60 mm outer dia pipe Each 4 273.15 1092.6 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming to JWWA G116 standard with V- 18.92 profile or M-profile and with O-ring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge. Equal Tee 174 18.92.2 For 22.22 mm outer dia pipe Each 8 300.2 2401.6 BHAVNAGAR DIVISION-ENGG/WESTERN RLY 175 18.92.3 For 28.58 mm outer dia pipe Each 8 466.6 3732.8 176 18.92.6 For 48.60 mm outer dia pipe Each 8 1429.75 11438 19.0 DRAINAGE 19.1S STONE WARE PIPES AND FITTINGS Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff 19.1 mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 177 19.1.2 150 mm diameter Metre 120 695.8 83496 178 19.1.5 300 mm diameter Metre 18 2064.15 37154.7 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand :10 19.2 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : 179 19.2.2 150 mm diameter S.W. pipe Metre 20 1179.85 23597 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water 19.4 tight C.I. cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 19.4.2 150 x 100 mm size P type 19.4.2.1 With common burnt clay F.P.S. (non Each 30 2734.2 82026 180 modular) bricks of class designation 7.5 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed 19.6 with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 181 19.6.4 300 mm dia. R.C.C. pipe Metre 120 994.3 119316 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size),foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), 19.7 inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (heavy duty) 560 mm internal diameter, total weight of 19.7.3 cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg) : 182 19.7.3.2 With Sewer bricks conforming to IS : 4885 Each 4 32719.5 130878 Providing and fixing in position pre-cast 19.19 R.C.C. manhole cover and frame of required shape and approved quality 19.19.1 L D- 2.5 19.19.1.1 Rectangular shape 600x450 mm internal Each 12 1437.65 17251.8 183 dimensions 184 19.19.1.2 Square shape 450 mm internal dimensions Each 6 1155.45 6932.7 185 19.19.1.3 Circular shape 450 mm internal diameter Each 6 1169.65 7017.9 19.19.2 M D - 10 BHAVNAGAR DIVISION-ENGG/WESTERN RLY 186 19.19.2.2 Circular shape 500 mm internal diameter Each 48 1172.6 56284.8 19.20 Supplying and fixing C.I. cover 300x300 mm Each 36 787 28332 without frame for gully trap (standard 187 pattern) the weight of cover to be not less than 4.5 kg Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 19.21 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : 188 19.21.1 For pipes 100 to 250 mm diameter Each 8 810.45 6483.6 189 19.21.2 For pipes 250 to 300 mm diameter Each 8 922.4 7379.2 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb 19.32 shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. 19.32.1 With common burnt clay F.P.S. (non Each 2 26861.9 53723.8 190 modular) bricks of class designation 7.5 21.0 ALUMINIUM WORK 21.1S General Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required 21.1 EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) : 21.1.1 For fixed portion 21.1.1.1 Anodised aluminium (anodised transparent Kg 420 495.05 207921 or dyed to required shade according to IS: 191 1868, Minimum anodic coating of grade AC 15) 21.1.1.2 Powder coated aluminium (minimum Kg 20 530.9 10618 192 thickness of powder coating 50 micron) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings 21.1.2 wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) 21.1.2.1 Anodised aluminium (anodised transparent Kg 960 598.6 574656 or dyed to required shade according to IS: 193 1868, Minimum anodic coating of grade AC 15) 21.1.2.2 Powder coated aluminium (minimum Kg 20 634.45 12689 194 thickness of powder coating 50 micron) BHAVNAGAR DIVISION-ENGG/WESTERN RLY Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in 21.2 panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. 21.2.2 Pre-laminated particle board with Sqm 64 1115.4 71385.6 195 decorative lamination on both sides Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene 21.3 gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): 21.3.1 With float glass panes of 4.0 mm thickness Sqm 102 1176.8 120033.6 196 (weight not less than 10kg/sqm) 22.0 WATER PROOFING 22.1S General 22.6 Providing and laying water proofing Sqm 424 688.9 292093.6 treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) after surface preparation, first layer of slurry of cement @ 0.488kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement 197 @1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured. 23.0 RAIN WATER HARVESTING & TUBEWELLS 23.1S General Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore 23.2 log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. 23.2.1 All types of soil 198 23.2.1.1 300 mm dia Metre 240 825.7 198168 BHAVNAGAR DIVISION-ENGG/WESTERN RLY Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 23.4 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in- charge. 199 23.4.3 200 mm nominal size dia Metre 60 1255.7 75342 26.0 NEW TECHNOLOGIES AND MATERIALS 26.41S NEW TECHNOLOGY ITEMS Providing and laying factory made Precast concrete solid blocks of 200 mm thickness 26.68 of grade M10 made of C&D waste from approved manufacturer in foundation and plinth in: 26.68.1 Cement mortar 1:6 (1 cement : 6 coarse cum 260.69 7387.25 1925782.2 200 sand) Providing and laying factory made Precast concrete solid blocks of 200 mm thickness 26.69 of grade M10 made of C&D waste from approved manufacturer in superstructure above plinth level up to floor V level 26.69.1 Cement mortar 1:6 (1 cement : 6 coarse cum 599.12 9844.65 5898126.71 201 sand) Total 66233267.46

Item Breakup - B-Electrical items

NS/1:SETC of Concealed wiring of light / fan/ Numbers exhaust fan/Call bell point

NS/2 : Concealed wiring of sub-main with Metre 4mm² copper wire in PVC conduit.

NS/3: Providing existing board.

NS/4: Providing board with two switches Numbers and two sockets of 6 amp.

NS/5 :SETC of 1200 mm sweep BLDC type Numbers ceiling Fan as per specification.

NS/6: SETC of MCB single phase RCBO of 32 Numbers A capacity 30 MA with metal enclosure as ser specification

NS/7: SETC of plug point 20 Amp with 20 A Numbers DP MCB in metal enclosure as ser specification

NS/8 : SETC of PVC Switch board of suitable Numbers size having 16/6 A 5 pin plug socket with 16 A switch as per specification.

NS/9: SETC of musical electronic bell

NS/10: SETC of TV point as per Specification Numbers

NS/11: SETC of 25 ltr capacity instant type Numbers geyser as per technical specification

NS/12: SETC of 18/20w LED Tube light as Numbers per specification

NS/13: SETC of LED light fittings 9-10 W as Numbers per specification.

NS/14: SETC of 250 mm sweep, color Numbers white/Blue blades with white dome & white body. it should be suitable to work on 250 v AC 50 C/S complete with all accessories as per technical specification.

NS/15 : SETC of MCB DB with incoming 32 Numbers amp DP MCb & outgoing 4x16 amp DP MCP as per specification. BHAVNAGAR DIVISION-ENGG/WESTERN RLY

NS/16: SETC of 5 mtr long galvanized Numbers octagonal pole with 130 mm bottom & 70 mm top made up of 3 mm thick steel along with base pipe size of 200x200x 12mm with foundation.

NS/17: Supply of 4 core 16 sq mm armored Metre XLPE aluminum cable IS-7098.4 led lighting fittings.

NS/18: Digging gf cable trench of 450x Metre 1000mm size in PCC/RCC /hard soil & refiling as per specification

NS/19: SETC of LED street iight 35-45 W Numbers fitting complete with all accessories etc. as per specification:.

NS/20: Supply of material and providing Numbers pipe earthing as per 3043 - 1987 as amended latest and as per specification. Total 2901990.00