Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹18.2 LAccepted-AOC KALLOORKAD GRAMA PANCHAYATH | KOLLAM | KERALA | 689694 | L1 | Accepted-AOC L1 | |
| 2 | L2₹19.1 L+₹91,270.72 (5.02%)Rejected-Finance | L2 | Rejected-Finance L2 | |
| 3 | L3₹19.3 L+₹1.1 L (6.20%)Rejected-Finance | L3 | Rejected-Finance L3 | |
| 4 | L4₹19.7 L+₹1.5 L (8.27%)Rejected-Finance | L4 | Rejected-Finance L4 | |
| 5 | L5₹20.9 L+₹2.7 L (14.8%)Rejected-Finance | L5 | Rejected-Finance L5 |
Tender Value
₹24.7 L
EMD Value
₹50,000
Closing Date
7 Apr 2025, 3:00 pmClosed
EXECUTIVE ENGINEER, PWD BUILDINGS DIVISION OFFICE,
EXECUTIVE ENGINEER, PWD BUILDINGS DIVISION OFFICE, TSR
DEPOSIT-Truss Roofing Over the Main building of Paramedical Ladies Hostel in Govt. Medical college, Thrissur-Truss Roofing Over the Main building of Paramedical Ladies Hostel-General Civil Work
2025_PWD_754705_1
79/2024-25/EE
Open Tender
Civil Works - Buildings
Item Rate
240 days
GMCH Thrissur
Please refer Tender documents.
10 documents required · 10 mandatory
₹2,760
Yes
₹50,000
Yes
4 Jun 2025
25 Mar 2025
10 Apr 2025
25 Mar 2025
7 Apr 2025
25 Mar 2025
Amount
Construction
50.10.1:Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete
50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete
12.50:Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
12.4.2:Providing ridges or hips width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.0.63 mm thick with zinc coating not less than 275 gm/m2
4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)
4.3.3:Centering and shuttering including strutting, propping etc. and removal of form work for:Columns, piers, abutments, pillars, posts and struts
13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work
OD280795/2024-2025:Providing and fixing UPVC Rain water gutter of 6" size to the galvanized sheet roofing to collect rain water firmly fixed to the truss member with all fittings to suit collect rain water such as center drop, end drop, joint, M S clamp, end cap etc complete.
50.18.9.19.2:Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 m dia 4 Kgf/cm2 - External work - Exposed on wall
OD269509/2024-2025:Providing and fixing Stainless steel wire mesh for Mosquito net door, window, ventilator shutters and partitions etc.. with EPDM rubber / neoprene gasket etc.. complete as per the architectural drawings and the directions of Engineer- in - charge ( coast of aluminium snap beading shall be paid in basic item) with stainless steel wire mesh Mosquito net.
21.5:Providing and fixing powder coated aluminium work ( minimum thickness of powder coating 50 micron) consisting of tee /angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-Charge ( level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately ).
14.43:Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.
13.48.1:Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm
OD270164/2024-2025:Removing the blocked materials from the sullage water drain around the building and depositing the dirty matters to a safe distant place within a distance of 150m etc.. complete, including cleaning the drain uprooting the vegetation and all labour charges etc.. complete, as per the direction of department officers at site.
OD226325/2023-2024:Engaging Coolie
OD280863/2024-2025:Engaging carpenter
OD280867/2024-2025:Engaging plumber
V M AZEEZ (BID ID -2189340)
IJAS C (BID ID -2189581)
EMMANUAL JOSE MANJALY (BID ID -2189286)
Binu MG (BID ID -2189810)
NIDHIN JOHN (BID ID -2188476)
Bidder Name
Binu MG
V M AZEEZ
Praveen Varghese
NIDHIN JOHN
IJAS C
EMMANUAL JOSE MANJALY
tech_eval.pdf
fin_eval.pdf
aoc.pdf
finance_1225476.pdf
boq_comp_chart.xlsx
xlsx
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .