Construction of New Collector Office at Himmatnagar Dist. Sabarkantha

Name of work :-

Construction of New Collector Office at

Himmatnagar Dist. Sabarkantha.

Bill of Quantities

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

1 Demolition including stacking of serviceable materilas and 29.00 Cum 1081.84

disposal of unserviceable materials with all lead and lift.

2 Demolition of Brick work and stone masonry including 26.00 Cum 562.85

stacking of serviceable materilas and disposal of

unserviceable materials with all lead and lift.(ii) In Cement

3 Dismentling steel work including distempering and 117.00 Kg 3.81

stacking the materials with all lead and lift.

4 Excavation for foundation upto 1.5 m depth including 3216.70 Cum 122.99

sorting out and stacking of useful materials and disposing

off the excavated stuff upto 50 Meter lead.(A) Loose or

5 Excavation for foundation upto 1.5 m depth including 4895.00 Cum 157.08

sorting out and stacking of useful materials and disposing

off the excavated stuff upto 50 Meter lead.(B) Dense or

6 Excavation for foundation for depth from 1.5 m to 3.0 m 3944.20 Cum 170.40

including sorting out and stacking of useful materials and

disposing off the excavated stuff upto 50 Meter lead.(B)

Dense or Hard soil

7 Excavation for foundation for depth from 3.0 m to 5.0 m 2041.00 Cum 183.75

including sorting out and stacking of useful materials and

disposing off the excavated stuff upto 50 Meter lead.(B)

Dense or Hard soil

8 Excavation for foundation for depth from 3.0 m to 5.0 m 1275.00 Cum 300.80

including sorting out and stacking of useful materials

and disposing of the excavated stuff upto 50 Meter

Lead.(C) Hard Murrum

9 Filling available excavated earth (excluding rock) in 17428.00 Cum 136.92

trenches. plinth, sides of foundations etc. in layers not

exceeding 20 cm. in depth consolidating each disposited

layer by ramming and watering.

10 Filling in plinth with sand under floors including watering 513.00 Cum 481.81

ramming, consolidating and dressing complete

11 Filling in foundation and plinth with murrum or selected 1535.00 Cum 294.39

soil in layers of 20cm. thickness including watering,

ramming and consolidating etc. complete.

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

12 Providing and laying controlled cement concrete M.150 3326.00 Cum 4183.42

for curing complete including cost of formwork but

excluding the cost of reinforcement for reinforced concrete

work in (A) Foundations, footings,Base of columns and

13 Providing and laying controlled cement concrete M.250 4522.00 Cum 4573.08

and curing complete including cost of formwork but

excluding the cost of reinforcement for reinforced concrete

work in (A) Foundations, footings, Base of columns and

14 Providing and laying controlled cement concrete M250 210.00 Cum 7682.06

and curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced concrete

work in Columns, pillars posts and struts Column Up to

15 Providing and laying cement concrete 1:4:8 (1- Cement : 4- 144.00 Cum 2844.57

coarse sand : 8- Machine Crushed stone aggregates

mm nominal size) and curing complete excluding cost of

formwork in (A) Foundation and Plinth

16 Providing and laying controlled cement concrete M.250 586.00 Cum 5998.39

and curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced concrete

work for Ground and Plinth Beams

17 Providing and laying controlled cement concrete M.200 634.00 Cum 7636.57

and curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced concrete

work in Columns, Pillars posts and struts, For All Floors.

18 Providing and laying controlled cement concrete M.200 80.00 Cum 7899.07

and curing complete including the cost of formwork

(Vertical fins and vertical sun breakers.) and

reinforcement for reinforced concrete work in (B) Walls,

for all floor level

19 Providing and laying controlled cement concrete M.200 571.00 Cum 5989.51

and curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced concrete

work in Beams For All Floors.

20 Providing and laying controlled cement concrete M.200 1000.20 Cum 6813.23

and curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced concrete

work in Slab for All Floors.

21 Providing and laying controlled cement concrete M.200 89.00 Cum 6395.80

and curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced concrete

work in Lintels For All Floors.

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

22 Providing and laying controlled cement concrete M.200 54.00 Cum 6978.73

and curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced concrete

work in Chajja For All Floors.

23 Providing and laying controlled cement concrete M.200 72.00 Cum 6887.38

and curing complete excluding the cost of formwork and

reinforcement for reinforced concrete work in (E)

Staircases For All Floors

24 Providing TMT Bar FE 500D reinforcement for R.C.C. 1205083.00 Kg. 77.29

work including bending, binding and placing in position

complete for All Floor

25 Providing and laying and fixing 50 mm thick expansion 226.00 Sqmt 1491.04

joint by hydro cell semi rigid UV resistance with high

performance laminated closed cell polythene foam joint

filler in sheet foam as directed, etc. complete.

26 Providing and filling the expansion joint by polymer 426.00 Sqmt 515.40

confirm to BS 4254-1983 as per required shade and

specifi-cation by making groove of 50 mm x 12.5 mm

lather by cutting or by repairing groove and removing

mortar drop or any other foreign materials including

applying primer and filling required size (oversize of joint

PU foam etc. complete.

27 Providing and fixing 25 cm Wide & 3mm thick exterior 26.00 Sqmt 1054.34

composite panel on existing expansion joint horizontally

&vertically with all material, hardware, acessories &

fittings etc completed.

28 Providing & Fixing to covering of expansion joint on 31.00 Sqmt 2162.41

terrace pre meta coated Galvalume Colour GCI (PPGL

sheet) 0.8mm thick including RCC. Wall having thickness

0.10x 0.30 mt. as per detail drawings using S.S. nut, bolts,

stud, washer and required all necessary material etc

complete as directed by Engineer in Charge.

29 Providing throating or plaster drip and moulding to R.C.C. 972.00 Rmt 43.08

Chhajja by making 5mm to 15mm wide grove as per

design etc. complete

30 Brick work using Common Burnt Clay building bricks 2111.00 Cum 4518.36

having crushing strength not less than 35 kg./Sq.Cm. in

Super structure Above plinth level up to All Floor levels in

Cement Mortar 1:6 (1- Cement : 6 -fine sand)

31 Half brick masonry in common burnt clay building bricks 1200.00 Sqmt 688.93

having crushing strength not less than 35 Kg/Sq.Cm. in

Superstructure above plinth level upto All Floor level in

Cement mortar 1:4 (1- Cement : 4 -coarse sand )

(Conventional).

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

32 Providing & Fixing Chicken mesh for joint between brick 2153.00 Sqmt 173.72

work & RCC work fixing with nail & GI washer as per

director in charge

33 Providing 15mm thick cement mala plaster in single coat 15845.00 Sqmt 256.58

on Rough (Similar)side of single or half brick walls for

interior plastering and finished even and smooth fininshing

with a floating coat of neat cement slurry in (i) Cement

mortar 1:3 (1-cement:3-sand), 10x10 mm groves etc.

Complete for All Floors.

34 Providing 10mm thick cement mala plaster in single coat 9436.00 Sqmt 231.58

on brick/concrete walls for interior plastering and finished

even and smooth fininshing with a floating coat of neat

cement slurry in (i)Cement mortar 1:3 (1-cement:3-sand).

Complete for All Floors.

35 20mm thick sand faced cement plaster with Gutka Finish 7603.00 Sqmt 321.10

on walls upto height 15 metres above ground level

consisting of 12mm thick backing coat of C.M. 1:3 (1-

cement : 3-sand) and 8mm thick finishing coat of C.M. 1:1

(1-cement : 1-sand) with 5mm grooves, etc. complete.

36 Providing Water Proofing Treatment on Sunk Slab 227.00 Sqmt 370.67

including cement concrete flooring 1:2:4 (1-cement : 2-

coarse sand : 4-graded stone aggregate 20mm nominal

size) laid in one layer and finished with a floating coat of

neat cement average 50mm thick to prepare slope

including water proofing chemical etc. Complete for Sunk

Slab for All Floor.

37 Masonary work using Aerated light weight concrete block 78.00 Cum 4598.93

having crushing strength not less than 35 kg/sqcm for

super structure above plinth level upto floor two level in

cement mortar 1:5 ( 1 cement : 5 fine sand ) complete as

per Technical Specification

38 Applying two coats of putty & one coats of primer of 22016.00 Sqmt 40.60

approved brand and manufacture on new wall surface to

give an even shade including thoroughly brushing the

surface free from mortar dropping and other foreign matter

and sand papered smooth.

39 Wall painting (three coats) with plastic emulsion paint of 12701.00 Sqmt 125.53

approved brand and manufacture on undecorated wall

surface to give an even shade including throughly brushing

the surface free from mortar droppings and other foreign

matter and sand papered smooth.

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

40 Ceiling painting (three coats) with plastic emulsion paint 9420.00 Sqmt 131.02

of approved brand and manufacture on ceiling and soffits

of slab surface to give an even shade including throughly

brushing the surface free from mortar droppings and other

foreign matter and sand papered smooth.

41 Finishing wall with weather proof exterior emulsion paint 10574.00 Sqmt 93.93

(two coats) with Damp Proof Coating (one coat) on wall

surface to give an required shape even shade after

thoroughly brushing the surface to remove all dirt, and

remains of loose powdered materials.etc complete

42 Providing and fixing pre-cast Rubber Dye / steel Dye inter 5105.00 Sqmt 706.93

locking concrete block 60mm thick with grade of concrete

M300 pnumatic compressed / vibrated mechanically and as

per approved design Confirming to IS 15658 :

including 35 mm Sand layer for levelling and filling the

joint with sand in proper line and level as per guidlines of

IRC : SP 63-2018 etc. Complete.

43 Providing and laying polished Granite stone slab flooring 327.00 Sqmt 2179.58

over 20mm (Average) thick base of cement mortar 1:6 (1-

cement : 6-coarse sand) or L.M. 1.1.5 (1-Lime putty :1.5 -

coarse sand) laid over and jointed with grey cement slurry

mixed with pigment to match the shade of slab including

rubbing and polishing etc. complete. (A) 25mm thick

44 Providing and fixing Machine cut & Polished Granite 10.00 Sqmt 2515.91

stone in 7.5 cm width Strip flooring for Ramp even grade

over 20mm (Average) thick base of cement mortar 1:6 (1-

cement : 6-coarse sand) laid over and jointed with grey

cement slurry mixed with pigment to match the shade of

slab including rubbing and polishing etc. complete. (A)

45 P & L 60 x 60 cm Soluble Salt vitrified 8 mm thick tile 2940.00 Sqmt 1324.11

flooring over 20 mm (average) base of cement mortar 1:6 (

1 cement: 6 coarse sand) on new surface or fixing on

existing flooring by adhesive material including

dismentaling of existing flooring and jointed with color

cement slurry including finised with flush pointing &

cleaning the surface etc. complete for Light shade

46 P & L 60 x 60 cm Soluble Salt vitrified 8 mm thick tile 327.00 Sqmt 1345.32

flooring over 20 mm (average) base of cement mortar 1:6 (

1 cement: 6 coarse sand) on new surface or fixing on

existing flooring by adhesive material including

dismentaling of existing flooring and jointed with color

cement slurry including finised with flush pointing &

cleaning the surface etc. complete for Dark shade

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

47 P & L 60 x 60 cm GVT vitrified 8 mm thick tile flooring 2586.00 Sqmt 1378.65

over 20 mm (average) base of cement mortar 1:6 (

cement: 6 coarse sand) on new surface or fixing on

existing flooring by adhesive material including

dismentaling of existing flooring and jointed with color

cement slurry including finised with flush pointing &

cleaning the surface etc. complete for Light shade

48 P & L 40 x 40 cm Full Body vitrified 8 mm thick tile 299.00 Sqmt 1432.18

flooring over 20 mm (average) base of cement mortar 1:6 (

1 cement: 6 coarse sand) on new surface or fixing on

existing flooring by adhesive material including

dismentaling of existing flooring and jointed with color

cement slurry including finised with flush pointing &

cleaning the surface etc. complete

49 Providing and laying Soluble Salt Vitrified tiles 8 to 10 165.00 Sqmt 1207.96

mm thick , 60 x 60 cm in skrting risers of steps and dedo

on 10mm thick cement plaster 1:3 (1-cement : 3-coarse

sand) and jointed with white cement slurry

50 Providing and laying GVT Vitrified tiles 8 to 10 mm thick 84.00 Sqmt 1262.50

, 60 x 60 cm in skrting risers of steps and dedo on 10mm

thick cement plaster 1:3 (1-cement : 3-coarse sand) and

jointed with white cement slurry

51 P & L 60 x 60 cm Matt Finished Antiskid Ceramic 10 mm 232.00 Sqmt 1378.65

thick tile flooring over 20 mm (average) base of cement

mortar 1:6 ( 1 cement: 6 coarse sand) on new surface or

fixing on existing flooring by adhesive material including

dismentaling of existing flooring and jointed with color

cement slurry including finised with flush pointing &

cleaning the surface etc. complete

52 P & L 30 x 30 cm Matt Finished Antiskid Ceramic 10 mm 116.00 Sqmt 1269.57

thick tile flooring over 20 mm (average) base of cement

mortar 1:6 ( 1 cement: 6 coarse sand) on new surface or

fixing on existing flooring by adhesive material including

dismentaling of existing flooring and jointed with color

cement slurry including finised with flush pointing &

cleaning the surface etc. complete

53 Providing and laying coloured glazed tiles of the size 300 2137.00 Sqmt 1487.89

mm x 450 mm x 8 mm in skirting, risers of steps and dedo

on 10 mm. thick cement plaster 1:3 (1 cement : 3 coarse

sand) & jointed with white cement slurry.

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

54 Providing and Fixing 15mm thick 300mm x 300mm 108.00 Sqmt 1058.48

Tactile Warning Tiles (Attention Tiles i.e. Tactile Warning

Surface Indicator {TWSI}) of Johnson Endura Tac Button

Yellow Plus or equvqlent make in flooring laid on 20mm

thick cement mortar 1:6 (1 cement: 6 coarse sand) on new

surface and jointed with cement slurry including finished

with flush pointing & cleaning the surface for all floors as

per detailed drawing etc. complete as directed by Architect

or Engineer in charge. These tiles shall be Antiskid,

Chemical Resistant, Fade Proof, Frost- Heat & weather

Proof, High Flexural Strength, Highly Durable, Stain

Resistance. All Tactile Warning Tiles meet the specific

size and Dimension standards as required by ISO/FDIS

55 Providing and fixing Machine cut, Free edges, Mirror 410.00 Sqmt 2464.40

Polished Granite stone slab flooring 18mm thick laid on

20mm (Average) thick base of cement mortar 1:6 (1-

cement : 6-coarse sand) for Trade & Riser including Half

Round moulding front edge of trade jointed with grey

cement slurry mixed with pigment to match the shade of

slab including rubbing and polishing etc. complete.

56 Providing and fixing Machine cut, Free edges, Polished 2154.00 Sqmt 2510.86

Green Granite stone slab flooring 18mm thick for vertical

wall/Doors/Windows Sill, Jams for cladding as per design

including full moulded round inside edge and laid

on10mm thick base of cement mortar 1:3 (1-cement : 3-

coarse sand) jointed with grey cement slurry mixed with

pigment to match the shade of slab including rubbing and

polishing etc. complete.

57 Providing and laying water prooofing treatment with china 2553.00 Sqmt 1132.21

mosaic tiles flooring over avg 50 mm C.C. 1:2:4 bedding

maintaining slope for plain and curve surface & 12 mm to

20 mm broken pieces not more than 2.5 cm of ceramic/ of

glazed tiles to be laid over cement mortar 1:3 to plain or

slope and to be tempered to bring mortar creme out upto

surface using white cement including rounding off

junctions and extending them upto 15 cm along the

wall,clearing with water and oxalic acid etc. as directed.

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

58 Constructing Sandwich Platform of 18mm thick polished 25.00 Sqmt 2760.33

black or selected granite at top and 25 mm thick kota stone

with 75cm height with necessary support using 20mm

thick cement mortar 1:3 for sandwich and fitting at bottom

& edges with waterproof rigid adhesive including making

necessary grooves in walls with vertical support of double

kota stonr sandwich every 60cm centre to centre including

all labour material of approved quality including full

moulded round front edge fixed in wall for partition.

59 Providing and fixing eco-friendly light weight calcium silicate false ceiling 5034.00 Sqmt 1807.40

tiles having Tegular edges & 15mm thick Densified edges on the Tile

Periphery for Extra Strength the Light weight calcium silicate ceiling tiles

shall have, light reflection 85% non-combustible as per B.S. 476 part IV,

100% humdity resistance and also having thermal conductivity 0.043° w/m

KC. for the best thermal insulation. The Light weight calcium silicate tile shall

be of approved texture Fine fissured/Spintone/Cosmos having NRC value of

0.5 & Globe having NRC value of 0.75 NRC or equivalent of size 595 x

mm to be laid on true horizontal level suspended inter locking metal grid of

hot dipped Galvanized Steel sections (Galvanized @120 grams per sqm

including both side) consisting of main 'T' runner suitably spaced at joints to

get required length and size of 24 x 38 mm made for 0.30 mm thick

(minimum) sheet, 1200mm centre to centre, amd cross 'T' of size 24 x 28mm

made of 0.33mm (minimum) sheet spaced 1200mm along spaced between

main 'T' at 600mm centre to centre to form agrid of 1200 x 600 mm and

secondary cross 'T' of length 600mm and size 24 x 28mm made 0.30mm thick

(minimum) sheet to be interlocked at middle of the 1200 x 600mm panel to

form grid of size 600 x 600mm resting on periphery wall/ partition on

parameter wall angle pre-coated steel of size (24 x 24 x 3000mm wide of

0.40mm thick (minimum) sheet with help of rawl plugs at 450mm c/c with

25mm long dry wall screw @230 mm interval and laying 15mm densified

edges light weight calcium silicate ceiling tiles of approved texture (Fine

Fissured/Cosmos/Spintones) in the grid including, cutting /making opening for

services like diffusers, grills, light fittings, fixtures, smoke detectors etc.,

wherever required, Main 'T' runners to be suspended from ceilings using G.I.

slotted cleats of size 25 x 35 x 1.6mm fixed to ceiling with 12.5mm dia and

50mm long dash fastners, 4mm G.I. adjustable rods with galvanized steel level

clips of size 85 x 30 x 0.8mm, spaced at 1200mm centre to centre long main

'T' bottom exposed with 24mm of all T-sections shall be pre-painted with

polyster baked paint, for all heights, as per specifications, drawings and as

directed by Engineer in-charges.

60 Providing and fixing flush door with Single shutters, solid 416.00 Sqmt 5153.02

core construction with frame of first class hardwood with

cross board and finished with 1 mm thick laminate on both

side of shutter, machine glued PVC beading on periphery

including 30cm long Stainless Steel Pipe handle on both

side SS ASIS 304 grade, SS Stopper 20cm, SS Aldrop

30cm both side, anodised alluminium butt hinges with

necessary screws. (B) Non-decorative type and block

board core anodised alluminium butt hinges in flush door

shutters (2) 38 mm thick.

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

61 Providing and fixing WPC (Wood Plastic Composite) with 70.00 Sqmt 5465.11

Single shutters, solid core construction with frame of first

class hardwood with cross board and finished with 1 mm

thick laminate on both side of shutter, machine glued PVC

beading on periphery including 30cm long Stainless Steel

Pipe handle on both side SS ASIS 304 grade, SS Stopper

20cm, SS Aldrop 30cm both side, anodised alluminium

butt hinges with necessary screws. (B) Non-decorative

type and block board core anodised alluminium butt hinges

in flush door shutters (2) 28 mm thick.

62 Providing and fixing flush door with Double shutters, solid 100.00 Sqmt 5197.46

core construction with frame of first class hardwood with

cross board and finished with 1 mm thick laminate on both

side of shutter, machine glued PVC beading on periphery,

including 30cm long Stainless Steel Pipe handle on both

side SS ASIS 304 grade, heavy duty Floor Spring each

side, SS Stopper 20cm, SS Aldrop 30cm both side,

anodised alluminium butt hinges with necessary screws.

(B) Non-decorative type and block board core anodised

alluminium butt hinges in flush door shutters (2) 38 mm

63 Providing and fixing window having extruded aluminum 881.00 Sqmt 1713.70

Colour anodized section frame main outer size 63.50 x

38.10 x 1.95 mm,@ Wt 1.094 Kg / Rmt, horizontal two

track member size 61.85 mm x 31.75 mm x 1.20mm @

wt.of 0.695 Kg/mt, vertical member of size 61.85 mm x

31.75mm x 1.30 mm @ wt.of 0.659 Kg/mt with sliding

shutters of horizontal member size 40mm x 18mm x

1.29mm @ wt.of 0.456Kg/mt, vertical member of size

0.457 Kg/mt with 5 mm thick transparent bronze colour

tinted float glass with powder coated aluminum fittings

and fixtures and transparent silicon sealant glass fixing to

frame as per details etc complete for window.

64 Providing and fixing aluminium extruded casement 25.00 Sqmt 6520.56

window frame equivalent to Jindal Series-B, using

aluminium sections Nos. 20558, 20559, 20560 &

including 5 mm thick transparent float glass, fixed with

approved transparent silicone sealant, complete with all

necessary fittings, fixtures, hardware, screws, and

accessories, finished with aluminium powder coating, and

fixed glass at top as per elevation, including all labour,

materials, and workmanship, complete in all respects as

per drawings, specifications, and direction of Engineer-in-

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

65 Providing, supplying and fixing partially openable 176.00 Sqmt 8694.08

structural glass panels using approved toughened safety

glass of specified thickness, complete with structural

support system, SS / aluminium fittings, hinges, patch

fittings, locking arrangement, handles, gaskets, EPDM

rubber, silicone sealant, nuts, bolts, anchor fasteners and

all other required fixtures, including cutting, drilling, edge

polishing, alignment and fixing to RCC / steel structure,

inclusive of all labour, materials, tools, scaffolding,

transportation, lifting arrangements, installation

machinery, safety measures and all incidental works,

complete in all respects as per approved drawings,

specifications and directions of Engineer-in-Charge.

66 Providing and fixing Standard extruded colour anodized 30.00 Sqmt 1368.55

alluminium section frame weight 1.094 kg/Rmt.with

Adjectable Glass Louvers of 5 mm thick transparent glass

colour tinted float glass with transparent silicon gasket

with allu. Powder coated fittings & fixtures.

67 SIGNAGES ON DOOR :Providing and fixing 304 grade 233.00 Nos. 1262.50

stainless steel 1.5mm thick brushed steel finish plate fixed

on a door using S.S studs and with punched (laser cut)

lettering carried out on S.S plate of required size and text

as directed by engineer etc. complete. Size 30 cm x 15 cm

68 Providing erecting and fixing double coated ISI water tank 21500.00 Litre 3.95

of required capacity each with all necessary fittings and

connection etc. complete on terrace

69 Providing, laying and jointing in true line and level 110 969.00 Rmt 876.12

diameter U.P.V.C (Type B) conforming to IS 13592-1992

with one end plain and other end socketed with rubber

ring, & fittings conforming to ISI 14735-1999 of approved

make for drainage system pipe line, pipe shall be jointed

with each other with rubber lubricant, pipe shall be fixed

on wall using of PVC clamp of the size 110 mm diametre

x 149 mm length x 145 mm heigh at every 2000 mm

center to center or shall be concealed in walls as directed

including necessary fittings such as bends, shoes etc.

including testing of pipes and joints and jointed with

adhesive solvent cement including cost of all materials.

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

70 Providing, laying and jointing in true line and level 160 165.00 Rmt 834.39

diameter U.P.V.C (Type B) conforming to IS 13592-1992

with one end plain and other end socketed with rubber

ring, & fittings conforming to ISI 14735-1999 of approved

make for drainage system pipe line, pipe shall be jointed

with each other with rubber lubricant, pipe shall be fixed

on wall using of PVC clamp of the size 160 mm diametre

x 210 mm length x 196 mm heigh at every 2000 mm

center to center or shall be concealed in walls as directed

including necessary fittings such as bends, shoes etc.

including testing of pipes and joints and jointed with

adhesive solvent cement including cost of all materials.

71 Providing laying and jointing in true line and level 50mm 330.00 Rmt 195.67

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every two metre

C/C or shall be concealed as directed including necessary

fittings etc. including testing of pipe and joints and fixing

the same with adhesive solvent, including cost of all

72 Providing laying and jointing in true line and level 40mm 892.00 Rmt 148.12

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every two metre

C/C or shall be concealed as directed including necessary

fittings etc. including testing of pipe and joints and fixing

the same with adhesive solvent, including cost of all

73 Providing laying and jointing in true line and level 25mm 825.00 Rmt 91.84

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every two metre

C/C or shall be concealed as directed including necessary

fittings etc. including testing of pipe and joints and fixing

the same with adhesive solvent, including cost of all

74 Providing laying and jointing in true line and level 15mm 560.00 Rmt 72.65

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every two metre

C/C or shall be concealed as directed including necessary

fittings etc. including testing of pipe and joints and fixing

the same with adhesive solvent, including cost of all

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

75 Providing and fixing concealed center point to wall ceiling 30.00 Rmt 253.83

& floor CPVC (SDR 13.5) PIPE having National

Sanitation Foundation (NSF) seal for potable water of

following dia. nominal bore tube fittings and clamps

including making good the wall, ceiling and floor etc.

complete. 25 mm.

76 Providing and fixing Gun metal check or non-return 28.00 Nos. 663.43

fullway wheel valve.(E) 40mm dia.

77 Providing and fixing Gun metal check or non-return 59.00 Nos. 420.64

fullway wheel valve.(C) 25mm dia.

78 Providing and fixing ball cock of approved. quality as 4.00 Nos. 189.84

directed.(A) Copper Metal (ii) 50mm dia.

79 Providing and fixing wash down water closet (Wall Hung 33.00 Nos. 9212.52

type, W.C. Pan) with integral P or S trap, Health Fauset

Heavy Duty with hook and PVC dual flush tank with

complete fittings including jointing the trap with soil pipe

in Cement Mortar 1:1 (1-Cement : 1-fine sand) (Seal and

cover to be measured and paid for separately)(A) vitreous

China Pattern :(i) in white colour

80 Providing and fixing water closet squatting Pan (Indian 24.00 Nos. 1637.51

type W.C. Pan) size 580mm (Earthwork, bed concrete,

foot reste and trap to be measured and paid for separately)

(A) Vitreous China.(I) Long pattern = White colour

including 100mm size P or S trap for water closet

squatting pan including jointing the trap with the pan and

soil pipe in cement Mortar 1:1 (1-Cement : 1-Fine sand)

with 25mm dia. chromium plated brass half trun flush

cock of approved quality including fixing in pipe line xing

G.I. inlet connection for flush pipe with W.C. Pan etc.

81 Providing and fixing Urinal or approved quality including 30.00 Nos. 1074.87

conecting the Urinal with waste pipe , tap etc.

complete.(A) White earthenware flat back or corner type

size 430mm x 260mm x 350mm.

82 Providing and fixing washbasin (ii) Flat Back washbasin 41.00 Nos. 2180.73

550 mm x v 400mm size. (i) In white colour including

with approved sanitary grade material with CP waste

coupling, waste pipe, 15mm dia Pillar & Stop Cock of

approved brand with connection 15mm dia flexiable pvc

pipe etc. complete

83 Providing and fixing Kitchen sink with C.I. or M.S. 33.00 Nos. 2987.88

brackets, painted white including cutting holes in walls (C)

Vitreous China Sink.(i) 600mm x 450mm x 150mm size

including approved sanitary grade material with CP waste

coupling, waste pipe, 15mm dia Pillar & Stop Cock of

approved brand with connection 15mm dia flexiable pvc

pipe etc. complete

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

84 Providing and fixing screw down bib taps of following 80.00 Nos. 186.83

size.(A) Brass screw down bib tap polished bright. (i)

85 Providing and fixing PVC SWR Nahni trap IS 14735 for 60.00 Nos. 586.60

drain - 100 mm diameter with jali of the following

nominal diameter of self cleansing design with C.I scread

down or hinged grating including the cost of cutting and

making good the walls.

86 Providing and fixing S.W. gully trap with C.I. grating 57.00 Nos. 1246.92

brick masonry chamber and water tight C.I. cover with

frame of 300mm x 300mm size (inside) with standard

weight.(i) Square mouth traps.(B) 150mm x 100mm size P

87 Providing and fixing C.P. brass towel rail comlete with 41.00 Nos. 616.43

C.P. brass brackets fixed to wooden plugs with C.P. brass

scews.(B) 600mm x 20mm size.

88 Providing and fixing 600mm x 450mm bevelled edge 40.00 Nos. 859.41

mirror of superior glass mounted on 6mm thick A.C. sheet

or plywood sheet and fixing to wooden pluge with C.P.

brass screws and washers.

89 Providing and fixing in position PVC cowel went to pipes 23.00 Nos. 75.75

90 Constructing brick masonry chamber for underground C.I. 51.00 Nos. 3660.76

Inspection chamber and bends with bricks having crushing

strength not less than 35Kg/Cm2 in C.M. 1:5 C.I. cover

with frame (Light duty) 455mm x 610mm intenal

dimensions total weight of cover with frame to be not less

than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. )

(R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand

:4-graded stone aggregate 20mm size) foundation concrete

1:5:10 inside plaster 15mm thick with cement mortar 1:3

finished smooth with a floating coat of neat cement on

walls and bed concrete etc. complete.(ii) Inside dimensions

500mm x 700 mm and 450mm deep for pipe line with one

91 Providing and laying (to level or slopes) and jointing with 200.00 Rmt 531.18

stiff mixture of Cement Mortar in proportion 1:1 Salt

glazed stoneware pipes including testing of pipes and

joints complete and Providing and laying Cement concrete

1:5:10 (1-Cement : 5-Fine sand :10-Graded stone

aggregate 40mm nominal size) bedding for stoneware

pipes of following internal diameters with necessary

formwork and curing complete.(B) 150mm dia.

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

92 Providing sock pit of 5.00 Cu.M. Volume including 2.00 Nos. 3445.19

excavating and filling brickbats with dry masonry work at

top for 45cm. height including covering the top with stone

including providing vatas in C.M. 1:3 with finishing

curing etc. complete as directed.

93 Applying general insecticide pest control treatment to 6942.00 Sqmt 80.62

floors, cupboards etc including labour materials etc.

complete. Using Imidacloprid 30.5 SCas Per IS 6313 part -

II( (0.075% concentration by mass) is recommended

10.5ml chemical diluted with 5 liters of water application

0.5 litre chemical /Sqm of surface is recommended as per

94 Anti-Termite System:Providing and laying of permanent 12827.00 Sqmt 80.62

piping technology anti-termite treatment before flooring

work by installing LLDP (Low linear density polyethylene)

tube of 8 mm O.D. & 6.4 mm 1.D. with inbuilt pressure

compensation chip every 30 cm interval in the tube, having

working pressure of 2 Kg/cm2 and release rate of

ltr/hour fixed by P-clips and nails. The LLDP pipe shall be

installed at the entire periphery of the building and at

internal network of building at a depth of 20 to 200 mm

under floor at every 2 to 3 mtr. c/c distance (adjusted as

per building layout ) & Ends of loop pass through a PVC

elbow of minimum 32 mm ID at junction box of wall and

floor level,entering into a steel reinforced grooved flexible

pipe of minimum 22 mm ID leading into junction box and

the loops shall terminate in junction boxes & test every

junction during injecting chemicals for termite control

treatment. The anti termite chemical Imidacloprid 30.5%

SC mix as per IS-6313 (part III) shall be injected by the

pressure pump diluted with water @ 10.5 ml/5 ltr of water

at the rate of 2 Kg/sq.cm @ 5 Ltr/SMT. The contractor

shall submit approved line plan for piping system and

junction boxes dully approved by Engineer-in-Charge with

bond of 5 year warranty.(i)Anti Termite chemical injected

area (Chemical injecting incl. labour cost)

95 Providing and fixing Safety Grills of required pattern for 45413.00 Kg 108.88

windows/door using MS polished bars, Rectangular CRS

Pipes of size 50mm x 30mm x 2mm or Required at

required spacing as per design and hold fast with coach

bolts including one coat of and two coats of matt finished

oil painting etc. complete

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

96 Providing upto floor two level precast cement concrete jali 71.00 Sqmt. 842.30

or grill 1:2:4 mix (1- Cement : 2- coarse sand : 4-graded

stone aggregate 6mm nominal size) reinforced with

mm dia. mild steel wire including roughening,cleaning,

fixing and finishing in cement mortar 1:3 and curing

complete.(E)100mm thick

97 Providing and fixing a set of wall mounted 38mm dia. U 56.00 Nos. 2323.00

shaped horizontal stainless steel collapsible grab bar,

38mm vertical stainless steel fixed grab rail of grade SS

304 from round pipe supported and 75mm dia 8mm thick

SS 304 base flange on wall including anchor fastners, nuts,

accessories as per detailed drawing etc. complete as

directed by architect or engineer in charge.

98 Providing and fixing 120 cm high Stainless Steel railing 302.00 Rmt 3586.41

made from anticorrosive 304 grade S.S. pipe of 50 mm

dia. (16 gauge) as hand rail with S.S.304 grade baluster of

32 mm dia (16 gauge) as a vertical support fixed in RCC

Slab/ steps of stair at 1.2 mt. c/c including three horizontal

S.S. pipes of 16 mm dia (16 gauge) at equal distance fixed

by 16 mm dia (16 gauge) S.S. pipe with baluster including

accessories as per detailed drawing as directwed etc.

99 Providing and fixing Aluminium Composite Panel (ACP) 383.00 Sqmt. 2716.90

cladding of approved shade and finish on front elevation

around structural glass panels, made from minimum 3–4

mm thick ACP sheets with aluminium skins, fixed on

MS/Aluminium framework comprising RHS / cleats /

brackets, duly anchored to RCC / masonry surface with

anchor fasteners, including cutting, bending, edge folding,

grooves, stiffeners, provision of necessary spacers, gaskets,

sealants, jointing with aluminium trims, weather-proof

silicone sealant, complete in all respects as per approved

design, drawings and direction of Engineer-in-Charge,

including labour, scaffolding, lifting, tools, transportation,

wastage, and all incidental charges.

100 Providing & Fixing in position 300 to 150mm high 50.00 Nos. 757.50

English/Gujarati letters made from 1.0mm thick stainless

steel sheet as directed by the Engineer in charge with all

material, hardware, accessories and fittings etc. complete.

101 Steel work, welded in built up sections framed work 540.00 Quintal 9108.49

including cutting, hoisting, fixing in position and applying

a priming coat of red lead paint. (A)In beams and joists,

channels angles Tees, flats, with connecting plates or angle

cleats as in main and cross beams. Hip and jack rafters,

purlins conneted to common rafters and the like

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

102 Painting two coats (excluding priming coat) on external 279.00 Sqmt 22.75

surface of new rain water, soil, waste and vent pipes and

fittings with ready mixed bituminous brushing, black,

anticorrosive to give an even shade including cleaning of

all dirt, dust and other foreign matter. (B) 75mm dia.

103 Providing and fixing Proflex type self supported roof 1243.40 Sqmt. 4560.15

(Arch type) using Cold rolled, Galvalume Steel colour

coated sheet 1.2 mm thick confirming to ASTMA

A792 DIN, Alu Zinc Coating : AZ150 and Regular

modified polyester painting with epoxy primer service coat

at bottom, including necessary fixtures & fastenings for

lighting arrangement and turbo ventilator with skylight.

104 Providing and Fixing Tactile Layout Plan of size 900mm x 3.00 Nos. 38380.00

600mm as approved design, made of 3.0mm thick acrylic

non glare base plate and non glare cut out symbols with

Braille on which individual facility points, like inquiry,

reception, restrooms, medical room/ first aid, cafeteria or

breakout area, lounge, meeting room, conference room etc.

present the respective floors with pictograph wherever

needed all in tactile raised by minimum of 1.0mm to 2mm

in various colours to make it legible for seniors, partial

vision impaired etc. All the facility names should be in

Braille, along with English or Hindi. The entire block of

tactile signs should be mounted on wall for easy reading.

The maps to be installed at specified locations and

installed at a height of 800mm from ground level complete

in all respect as per Harmonized guideline & satisfaction

of Engineer in Charge.

105 Providing and Fixing of acrylic, non-glare, tactile audio 3.00 Nos. 50500.00

pictorial building layout as per the approved size, design

and make, having 3mm thick acrylic non glare base plate

of approved colour and non-glare cut out symbols raised

3mm above base plate and Grade 2/ Grade 1 Braille to be

integral with the sign face and be raised 0.5mm above base

plate. The map to be installed at the specified location as

per accessibility standards, shall be oriented to the position

of the viewer and to be installed at the height of 800mm

from the finished ground/ floor level and using the

necessary hardware specified by the manufacturer and to

be installed complete as per design/specifications and

guidelines as per the entire satisfaction of the Engineer in

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

106 Providing and Fixing ACP Sheet Overhead Gantry Sign 3.00 Sqmt. 2525.00

Board Material used 4mm thick ACP sheet 2mm thick

aluminum sheet Reflective sheeting HIP (Type-IV)

Engineering grade High-Inensity grade Diamond Grade or

as required by customer size of board as per client's

required shape rectangle board with 3D Letter Cut-outs.

107 Providing and fixing braille dot and text Sign plate as per 11.00 Sqmt. 34239.00

standard ADA basis on wall / door made out of avg. 2mm

alluminum sheet/4mm ACP of Required size coated with

one coat of epoxy primer and two coat of best quality

epoxy paint reflectorised with High Itensity Primastic

Grade retro reflective sheeting. The details of symbols for

each board shall be as per the instruction, The fixing on

wall/ Door at site shall be done with necessary screw etc

108 Excavation for foundation for depth from 1.5 m to 3.0 m 1383.00 Cum 287.47

including sorting out and stacking of useful materials and

disposing off the excavated stuff upto 50 Meter lead.(C)

109 Excavation for foundation for depth from 3.0 m to 5.0 m 817.00 Cum 324.52

including sorting out and stacking of useful materials

and disposing off the excavated stuff upto 50 Meter

lead.(D) Soft rock not requiring Blasting

110 Providing and laying in position Ready Mixed M-300 2446.00 Cum 5226.82

grade concrete for reinforced cement conctere work , using

cement content as per approved Design Mix manufactured

in fully automatic batching plant and transported to site of

work in transit mixer for a lead up to 10 kms having

continuous agitated mixer, manufactured as per mix design

of specified grade for reinforced cement concrete work

including pumping of R.M.C. from transit mixer to site of

laying, excluding the cost of centering shuttering finishing

and reinforcement including cost of admixtures in

recommended proportions as per IS: 9103 to accelerate/

retard setting of concrete, improve workability without

impairing strength and durability as per direction of the

Engineer - in - charge. Without Fly Ash (Min cement

level as per latest IS 456 shall be maintained) (Cement

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

111 Providing formwork with sheathing steel sheet so as to 239.00 Sqmt. 280.69

give a finished surface including centering shuttering

strutting and propping etc. Height of propping and

centering below supporting floor to ceiling not exceeding

4 M. and removal of the same for in situ reinforced

concrete and plain concrete work in (Upto 10 ton) (A)

Foundations Footings Bases of Columns etc. and Mass

112 Providing formwork with sheathing steel sheet so as to 1325.00 Sqmt. 357.12

give a finished surface including centering shuttering

strutting and propping etc. Height of propping and

centering below supporting floor to ceiling not exceeding

4 M. and removal of the same for in situ reinforced

concrete and plain concrete work in (Upto 10 ton)

(C)Vertical surface such as walls (any thickness) partitions

& lime including attached pilasters buttresses plinth &

string course & like.

113 Brick work using common burnt clay building bricks 203.00 Cum 4214.33

having crushing strength not less than 35 kg./Sq.Cm. in

foundation and plinth in Cement Mortar 1:6 (1- Cement :

-fine sand) (Conventional)

114 Providing and laying controlled cement concrete M.150 68.00 Cum 7426.53

and curing complete excluding the cost of formwork and

reinforcement for reinforced concrete work for Coping

115 Providing & laying weep hole in Aburtments, and returns 2886.00 Each 86.73

by using A.C. pipe of 100mm including laying in proper

grede and jointing the completed as per detailed

116 Providing and laying - Filter Media 600mm thick directed 500.00 Sqmt 1238.93

at the back of abutments, returns and wing walls as per

detailed specifications.

117 Provding and applying Exterior grade Exposed concrete 6801.00 Sqmt 2716.90

texture finish (concrete design wall texture) of approved

make and shade over prepared surface, including surface

cleaning, primer application, base coat, texture coat

application to achieve exposed texture concrete panel

appearance with groove/joint pattern as shown in drawing,

curing, scaffolding, labour, materials, tools and all

incidental charges complete as directed by the Engineer-in-

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

118 Providing and fixing concertina coil fencing with punched 1293.00 Rmt. 565.60

tape concertina coil 600 mm dia 10 mt openable length

having 50 no rounds per 6 mt length, upto 3mt height of

wall with existing angle iron (50mm x50mm x5mm

)requird shaped As per Directed Engeenier in charge.

placed 2.4mt or 3.00mt apart and with 4 horizontal R.B.T.

reinforced barbed wire(3 mm) , stud tied with G.I. staples

and G.I. clips to retain horizontal, including necessary

bolts or G.I.barbed wire tied to angle iron, all complete as

per direction of Engineer-in-charge, with reinforced barbed

tape (R.B.T.)/Spring core (2.5 mm thick) and weight

43.478 gm/meter at compound wall for ESR

119 Supplying and fixing reinforced concrete heavy duty non- 650.00 Rmt. 1190.06

pressure pipes with collars for culverts carrying heavy

traffic as per IS 458-1991 specifications including setting

the pipes in C.M. 1:2 watering and laying (to level or

slopes) of class NP3 of following internal daimeters.(ii)

120 Constructing brick masonry road gully chamber 1100mm x 10.00 Nos. 8767.26

775mm including 500mm x 450mm (C.I. horizontal

grating with frame and vertical grating complete.)

121 Drilling of pilot bore hole of size 250/300 mm diameter at 850.00 Rmt 1544.29

above site by mud finish direct rotary rig etc. complete

122 Reaming of 250/300 mm diameter pilot bore hole to size 600.00 Rmt 742.35

450 mm diameter including assembling, lowering housing,

casing strainer pipes with gravel packing and clay ball

packing etc. complete.

123 Providing 600 CFM / 150 PSI capacity air compressor 2.00 Job 25118.70

upto available of sand free discharge ( Minimum

124 Supply of reducer made frim 6 mm thick plate (M.S.) for 2.00 Nos. 2009.90

ERW pipe of size (ii) 200 mm dia. x 250 mm dia. X

125 Supply of 200 mm diameter V-wire screen pipe of slot size 200.00 Rmt 1401.88

1.0 mm nominal hole etc. complete.

126 Supply of M.S. Bore clamps with 3 holes on either side 2.00 Pair 1753.36

with nuts and bolts of standard make and suitable size (g)

750 mm x 75 mm x 16 mm flat to 200 mm dia. Pipe.

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

127 Supply of Bore Plug having 100 mm height made from 2.00 Nos. 834.26

M.S. plate with 3 holes at equal distance on circumference

for nuts-bolts type, locking arrangement with nut-bolts &

lock nuts of standard make complete. (b) from 5 mm thick

M.S. plate (for top also) (ii) suitable for 200 mm dia. pipe.

128 Supply of M.S. Bail Plug having length of 0.45 mtr from 2.00 Nos. 907.99

medium class pipe as per I.S.S. suitable for (b) 200 mm

diameter pipe etc. complete.

129 Supply of Steel Bent plates suitable to ERW pipe for (b) 16.00 Nos. 71.71

200 mm diameter and 150 x 150 x 6 mm size etc.

130 Supply of Gravel of size selected size up to 4mm to 6 mm, 24.00 Cmt 2295.73

including stacking and filing etc. complete.

131 Charges for uptron make Electrologger (with carting ) of 2.00 Job 12120.00

pilot bore hole etc. complete.

132 Charges for Geo Hydrological ground water investigation 10.00 Job 16160.00

including water sample chemical analysis etc. complete.

133 S.I.T.C. submersible pump set suitable for bore of 150 mm 2.00 Each 49148.62

dia or more having 3 phase motor capacity not less than

HP with following capacity. Lifting and Lowering taken

extra. [C] 25 stage 160 to 100 LPM discharge at 185 to

220 mtr head for 50 mm dia delivery pipe

134 Providing and erecting PVC corrugated Flexible conduit 550.00 Rmt 26.26

with required numbers of coupling, PVC bushes, Check-

nuts etc. complete of following sizes. (3) 32 mm diameter

135 Lowering of submersible motor pump set complete with 2.00 Job 2568.43

required. Nos. and size of casing pipes erected by means of

proper chain pulley block & pipe wrenches after checking

of threads of each pipe with coupling to take the load of

the pump set and pipe assembly filled up with water. (B)

Above 60 mtr and up to 120 mtr

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

136 Supplying and erecting approved make motor control 2.00 Each 8710.24

cubical panel (Direct - on - line) made from 16 G. CRCA

sheet duly epoxy powder painted inside and outside with

hinged doors and locking, arrangement consisting of

suitable size of ON-OFF isolator (AC - 3/23 duty) main

fuses, single phasing preventer, indicating lamps for R-Y-

B phases, overload relay, automatic water level controller,

Ammeter, Voltmeter each with two way selector switch

incoming, wires duly socket crimped, main contactor &

overload relay, start-stop push buttons, to be erected on

angle iron frame grouted on wall as directed. The isolator,

overload relay & contactors will be of L&T, Seimens or

BCH make only (a) DOL upto 7.50 H.P.

137 Supplying and erecting XLPE (IS:7098) (I)-88 ISI 600.00 Rmt 136.35

unarmoured copper cable 1.1 KV grade to be erected as

directed of following size. (E) 3 core 2.5 Sq. mm

138 Providing laying and jointing in true line and level 50mm 700.00 Rmt 195.67

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every two metre

C/C or shall be concealed as directed including necessary

fittings etc. including testing of pipe and joints and fixing

the same with adhesive solvent, including cost of all

139 Providing and fixing butterfly valve of IS approved brand 4.00 Nos. 1595.80

140 Providing and laying polished Kota stone slab flooring 24.00 Sqmt 1019.00

over 20mm (Average) thick base of cement mortar 1:6 (1-

cement : 6-coarse sand) or L.M. 1.1.5 (1-Lime putty :1.5 -

coarse sand) laid over and jointed with grey cement slurry

mixed with pigment to match the shade of slab including

rubbing and polishing etc. complete. (A) 25mm thick

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

141 Providing and fixing window having extruded aluminum 5.00 Sqmt 1583.96

Colour anodized section frame main outer size 95mm x

24mm x 1.17mm @ wt.of 0.738 Kg/mt , horizontal Three

track member size 92mm x 31.75mm x 1.30mm,@

Wt.1.07 Kg/mt , vertical member of size 92mm x

31.75mm x 1.50mm @ Wt. 1.06 Kg/mt with sliding

shutters of horizontal member size 40 mmx18mm

x1.29mm @ wt.of 0.456 Kg/mt, vertical member of size

40mm x 18mm x 1.29 mm @ wt.of 0.456Kg/mt/ with

mm thick transparent bronze colour tinted float glass with

rubber gasket and airlock strip anodiazed aluminum

fittings and fixtures and transparent silicon sealant glass

fixing to frame as per details etc.

142 Providing and fixing C.I. Manhole cover 0.60 M. x 0.45M. 7.00 Nos 958.17

size having weight not less than 35Kg.

143 Clearing and grubbing road land including uprooting rank 4.00 Hectare 34889.38

vegetation grass bushes,shrubs,sapling and trees girth up to

300 mm removal of stumps of trees cut earlier and

disposal of unserviceable materials(D) By mechanical

means in area of thorny jungle

144 Earthwork in cuting in all sorts of soil and soft murrum 23717.00 Cum 134.20

including conveying and spreading the stuff, embankment

as and where directed within 200meters from the end of

the cutting with all required lead and lift.

145 Earthwork in cutting including preparing the slope and 71150.00 Cum 260.57

camber and stacking or utilising the cutting stuff in bank as

directed upto 200 Meters from the end of cutting with all

lead and lift.(i) Hard murrum.

146 Earthwork for embankment including breaking clods, 50907.23 Cum 131.93

dressing with all lead and lift (including watering and

consolidation)(A) From Borrow pits within land width

147 Rolling and consolidation of soling including filling in 43950.00 Sqmt. 22.75

depression which occur during the process, with power

roler 8 tonne to 12 tonne..

148 Box cutting the road surface to proper slope and camber 4350.00 Cum 109.05

for making a base for road work including removing the

excavated stuff and depositing on the road side slope as

directed upto 50Mt.lead.

149 Construction of B.I.T.C. granular sub base by providing 6299.00 Cum 1132.02

granular material of Grading II, spreading in uniform

layers with motor grader on prepared surface , mixing by

mix in place method with front end loader at OMC , and

compacting with vibratory roller to achieve the desired

density ,complete as per Clause

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

150 Providing, laying, spreading and compacting stone 1865.00 Cum 1473.75

aggregates of specific sizes to water bound macadam

(Grade-II) (B.T. Metal of size 45 to 63 mm) specification

including spreading in uniform thickness, hand packing,

rolling with 3 wheeled steel/ vibratory roller in stages to

proper grade and camber, applying and brooming requisite

type of screening/ binding Materials to fill up the

interstices of coarse aggregate, watering and compacting to

the required density.

151 Compaction and finishing of cement concrete road by 8193.00 Sqmt. 72.72

trimix process providing extra labour charges for the

trimix vaccum dewatering service process on cement

concrete road surface by using vaccum dewatering pump

floater surface vibrator including making rough finish to

surface as per in including levelling the complete.

152 Road marking with hot applied thermoplastic paints with 288.00 Sqmt. 367.73

reflectorising glass beads on Concrete surface providing

and laying a hot applied thermoplastic compound 2.5 mm

thick including reflectorising glass beads @ 250gms per

sqm area,thickness of 2.5mm is excluding of surface

applied glass beds as per IRC:35-2015. The finished

surface to be level, uniform and free from streaks and

holes. zebra patta /bump patta lane/center line/ edge

line/cut patta. The white color marking should provide

liminance coefficinet on cemend road shalll be min

mcd/m2/lux and Asphalt road shall be min

mcd/m2/lux during the service life during the day time.

The marking should meet the performance criteria for

night time reflectivity, wet reflectivity and skid resistance

as mentioned in the section-15 of IRC 35-2015. Warranty

for the Retro reflectivity should be two years.

153 Supplying and fixing reinforced concrete heavy duty non- 130.00 Rmt. 660.00

pressure pipes with collars for culverts carrying heavy

traffic as per IS 458-1991 specifications including setting

the pipes in C.M. 1:2 watering and laying (to level or

slopes) of class NP3 of following internal daimeters.(i)

154 Construction of Cattle trap made from ISMC 100 border 36.00 Sqmt. 6146.86

and G.I. pipe 50 mm dia. Heavy duty at 12cm spacing by

welding and for supports 2 nos. I.S.M.C. 100x75x6 section

fixing in prepared chamber as per drawing.

155 Constructing Brick masonry road gully chamber 500mm x 52.00 Nos. 2017.20

450mm x 600mm including 500mm x 450mm C.I.

horizontal grating wih frame complete.

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

156 Providing and fixing pre-cast concrete kerb stone of gray 1500.00 Rmt 404.06

cement based concrete block 30cm length,30cm height and

15cm thick of M200 grade concret as per approved design

and including excavation for fixing in proper line and

Level,filling the joint with C:M 1:3 (1cement:3fine sand)

157 Facility Informatory Sign :-Providing and fixing sign 5.00 Nos. 3990.65

boards made out of 2mm aluminium sheet / 4mm ACP

(Aluminum composite Panel); size 80 x 60 cms.

rectangular as per design of IRC-67-2012. Pre treated with

phospheting process & acid etching; coated with one coat

of epoxy primer and two coats of best quality epoxy paint ;

reflectorised with High Intensity Prismatic Grade retro

refiectivesheeting of Type-4 as per ASTM D-4956 and

latest M.O.S.T.Specifications; 3.6mtr long stand post of

Iron Angle 75 x 75 x 6mm / 65NB Circular MS Pipe as

required and frame fabricated from suitable size iron angle

of 35 x 35 x 3mm; painted with bestquality epoxy coatings

in black and white bends. The details of symbol for each

board shall be as per the instruction of engineer in charge.

The fixing at site shall be in 1:2:4 CC blockof size 45 x

x 60 Cms. for each leg including excavation, curing

etc.complete under the supervision of engineer in charge.

A warranty for 7 years for the Retro reflective sheeting

from original manufacturer & a certified copy of 3 year

outdoor exposure test report from third party test lab for

the product offered shall be submitted by contractor. (B)

Class-B Type-4 Retro Reflective sheeting.

158 Supplying of yellow or Goradu soil with all lead and lift 1975.00 Cum 505.00

including spreading watering dressing and rolling with

hand roller etc complete selected soil

159 Supplying of well rotted FYM manure with all lead and lift 99.00 Cum 378.75

including spreading mixing dressing and rolling with hand

roller etc. complete

160 Scarifying the surface of soil including spreading of DAP 3950.00 Sqmt. 26.26

fertilizer mixing with soil properly leveling ground

dressing of the plot

161 Supplying and planting Dibbling semi carpet lawn at 3950.00 Sqmt. 90.90

distance of about 15 cm x 15 cm after proper anti termite

treatment and rolling the same by hand roller and watering

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

162 Bowling and developing flowering plants grown in nursery 200.00 Nos. 1010.00

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer

pesticides, fungicides, hormones & maintaining the plants

up to three months as Deserted Arrica Palm

163 Bowling and developing flowering plants grown in nursery 200.00 Nos. 1313.00

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer

pesticides, fungicides, hormones & maintaining the plants

up to three months as Deserted Triangle Palm

164 Bowling and developing flowering plants grown in nursery 200.00 Nos. 161.60

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer

pesticides, fungicides, hormones & maintaining the plants

up to three months as Jasud

165 Bowling and developing flowering plants grown in nursery 100.00 Nos. 171.70

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer

pesticides, fungicides, hormones & maintaining the plants

up to three months as Croton

166 Bowling and developing flowering plants grown in nursery 120.00 Nos. 171.70

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer

pesticides, fungicides, hormones & maintaining the plants

up to three months as Deserted Croton

167 Bowling and developing flowering plants grown in nursery 100.00 Nos. 141.40

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer

pesticides, fungicides, hormones & maintaining the plants

up to three months as Deserted Croton Petra

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

168 Bowling and developing flowering plants grown in nursery 130.00 Nos. 80.80

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer

pesticides, fungicides, hormones & maintaining the plants

up to three months as Deserted Croton Petra Live Plant

169 Bowling and developing flowering plants grown in nursery 180.00 Nos. 202.00

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer

pesticides, fungicides, hormones & maintaining the plants

up to three months as Deserted Golden Durenta Varigated

170 Bowling and developing flowering plants grown in nursery 100.00 Nos. 171.70

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer

pesticides, fungicides, hormones & maintaining the plants

up to three months as Deserted Crotons Variety

171 Bowling and developing flowering plants grown in nursery 500.00 Nos. 70.70

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer

pesticides, fungicides, hormones & maintaining the plants

up to three months as Deserted Green Mahindi

172 Bowling and developing flowering plants grown in nursery 150.00 Nos. 171.70

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer

pesticides, fungicides, hormones & maintaining the plants

up to three months as Deserted Varigated Ficus

173 Bowling and developing flowering plants grown in nursery 140.00 Nos. 141.40

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer

pesticides, fungicides, hormones & maintaining the plants

up to three months as Deserted New Black Ficus

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

174 Bowling and developing flowering plants grown in nursery 690.00 Nos. 90.90

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer

pesticides, fungicides, hormones & maintaining the plants

up to three months as Deserted White Ribbon Plants

175 Bowling and developing flowering plants grown in nursery 600.00 Nos. 121.20

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer

pesticides, fungicides, hormones & maintaining the plants

up to three months as Deserted Green Mahendi border

176 Bowling and developing flowering plants grown in nursery 200.00 Nos. 191.90

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer

pesticides, fungicides, hormones & maintaining the plants

up to three months as Deserted Pendulla Asopalav

177 Bowling and developing flowering plants grown in nursery 100.00 Nos. 242.40

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer

pesticides, fungicides, hormones & maintaining the plants

up to three months as Deserted Potted Plants

178 Labour charges for planting various plantsafler proper anti- 3710.00 Nos. 70.70

termite treatment in pits including placing properly and

filling the pits with required prepared mix soil and

watering and dispporting etc. complete

179 Maintance of the garden for 60 days after Complition of 3 1.00 Job 25250.00

month stipulated period is completed for plantation of

lawn and plants including applying second round of proper

anti-termite treatment

180 Providing and fixing brass screw down stop cock (A) 15 20.00 Nos. 205.83

181 Rubber Hose Pipe 15 mm dia of approved brand and make 300.00 Rmt 90.90

182 Providing and fixing G.I. Nipple as directed 300.00 Nos. 101.00

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

183 Providing & Laying Rain Water Junction Chamber of 30.00 Nos. 6241.80

Clear Internal Size 0.60 x 0.60 x 0.75m with excavation of

size 1.36 x 1.36m & 0.15m thick M200 Bed Concrete

Including brick masonary 0.23 thick wall in C.M. 1:6 of

0.75m height with 15mm thick Cement Plaster inside &

outside (1:4), 1.06 x 1.06 RCC M200 top slab of thickness

0.15m with TMT steel and 455mm x 610mm cast iron

manhole cover with frame weight not less than 35 kg as

per directed by Engineer-in-charge.

184 Providing & Laying Filter chamber of brickwork 0.23 30.00 Nos. 22067.49

thick in C.M. 1:6 of clear internal size 2.04m x 1.20m x

1.20m and excavation dimension of 2.80m x 1.96m x

1.35m including C.C. M200 Bed Concrete 0.15m thick

and RCC M200 Top slab of thickness 0.15m with TMT

steel, Including 15mm (1:4) thick cement plaster inside &

outside with Cement slurry & top cover with frame of

minimum weight of 35kg, including filling filter material

of 200mm thick each layer of 25-40mm, 10-20mm of BT

metal and sand as per directed by engineer-in-charge

185 Providing & Laying Water Harvesting Pit of clear size 1.00 Nos. 32558.36

2.00 mt x 2.00 mt x 4.00 mt. For water logging with

excavation in any strata upto four meter depth, Brick work

0.23 thick in C.M. 1:6 of clear internal size 2.00m x 2.00m

x 1.20m with 15mm thick C.M. 1:4 plaster, filling the pit

with B.T. metal 40mm in 0.60 mt. depth with 25-40mm

kaptchi, 0.30 mt. depth and 2mt. depth with coarse sand in

layers including makng P.V.C. line for water inlet etc. as

directed with 250mm dia bore 15mt. depth amd 150mm

dia PVC pipe of 10 Kg.f/cm2 casing wih gravel packing or

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

186 Electric Motor Driven Hydrant Pump Location - Plant Room 1.00 Nos. 555500.00

Providing, Installing, testing and commissioning of Fire authority approved

Electrical driven fire pump suitable for automatic/manual operation consisting

of the following-Rates for erection of pump only (i) End Suction, high

pressure, single/ multistage centrifugal type fire pump having cast iron body,

bronze impeller, stainless steel shaft & capable of delivering 1620 LPM (27

LPS) against a total head of 70Mtr while running at 2900 RPM complete with

proper connection to suction and delivery line, and including bypass

arrangement for testing of pumps as per the requirement. Suitable mechanical

seal with mounting aggangement shall be included, having a name plate

indicating suction, delivery, head, discharge, stages, RPM and direction of

rotation. Pump shall be capable of furnishing not less than 150% of rated

capacity at a head not less than 65% of rated head. The shut off head shall not

exceed 120% of rated head. (ii) Squirrel cage, induction motor, TEFC type

suitable for 415 + 10%V, 3 phase, 50 Hz, AC supply, of suitable HP rating for

the above pump with synchronous speed of 2900 RPM conforming to IP

protection & class 'F' insulation. The motor shall conform to IS 325 1978 (up

to date) with flexible coupling and coupling guard. (iii) Factory Fabricated

Common base plate for mounting pump and motor fabricated of mild steel

channel as per manufacturer's recommendation with heavy duty Anti Vibration

pads (4 Nos., heavy duty). Grouting bolts to be provided and installed by

vendor at his cost. (iv) Flexible Coupling and coupling guard for direct

coupling of pump and motor. (v) Drain Pipe with Valve.

Discharge : 1620 LPM (27 LPS)/97 m3/hr

Pumping Head : 70 M

(vii) Rate should included interconnection cables and Cable box if reqd for

cable conn. to motor.

187 Electric Motor Driven Sprinkler Pump Location - Plant Room 1.00 Nos. 555500.00

Providing, Installing, testing and commissioning of Fire authority approved

Electrical driven fire pump suitable for automatic/manual operation consisting

of the following-Rates for erection of pump only (i) End Suction, high

pressure, single/ multistage centrifugal type fire pump having cast iron body,

bronze impeller, stainless steel shaft & capable of delivering 1620 LPM (27

LPS) against a total head of 70Mtr while running at 2900 RPM complete with

proper connection to suction and delivery line, and including bypass

arrangement for testing of pumps as per the requirement. Suitable mechanical

seal with mounting aggangement shall be included, having a name plate

indicating suction, delivery, head, discharge, stages, RPM and direction of

rotation. Pump shall be capable of furnishing not less than 150% of rated

capacity at a head not less than 65% of rated head. The shut off head shall not

exceed 120% of rated head. (ii). Squirrel cage, induction motor, TEFC type

suitable for 415 + 10%V, 3 phase, 50 Hz, AC supply, of suitable HP rating for

the above pump with synchronous speed of 2900 RPM conforming to IP

protection & class 'F' insulation. The motor shall conform to IS 325 1978 (up

to date) with flexible coupling and coupling guard. (iii) Factory Fabricated

Common base plate for mounting pump and motor fabricated of mild steel

channel as per manufacturer's recommendation with heavy duty Anti Vibration

pads (4 Nos., heavy duty). Grouting bolts to be provided and installed by

vendor at his cost. (iv) Flexible Coupling and coupling guard for direct

coupling of pump and motor. (v) Drain Pipe with Valve.

Discharge : 1620 LPM (27 LPS)/97 m3/hr

Pumping Head : 70 M

(vii) Rate should included interconnection cables and Cable box if reqd for

cable conn. to motor.

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

188 Electrical Motor Driven Jockey Pump For Hydrant and Sprinkler System 1.00 Nos. 95950.00

Location - Plant Room Providing, Installing, testing & commissioning of fire

authority approved electrically driven Jockey pump suitable for

automatic/manual operation consisting of the following: (i) Horizontal

mounted multistage jockey pump having cast iron body, S.S. impeller,

stainless shaft with mechanical seal capable of delivering 180 LPM against

total head of 70 Mtr while running at 2900 RPM complete. The system shall

be complete with necessary pressure gauge with gun metal shut off cock on

delivery side including bypass arrangement for testing of working of the

pumping set as required. The pump should meet the requirement of IS

15105:2002 and must be approved by the local fire authority.(ii) Squirrel cage

induction motor suitable for 415 + 10%V, 3 phase, 50 Hz, AC supply of

suitable HP rating for the above pump with synchronous speed of 2900 RPM

T.E.F.C type connected to pump with flexible coupling and coupling guard.

(iii) Factory fabricated Common base plate for mounting pump and motor

fabricated of mild steel channel as per manufacturer's recommendation with

heavy duty 4 Nos. Anti Vibration pads. (Cushy foot). grouting bolts to be

provided and installed by the vendor at his cost (iv) Suitable reinforced cement

concrete pump foundations as per manufacturer's design including foundation

bolts, washers as required. (v) Drain pipe with valve (25 mm dia)

(vi) Jockey Pump :-

Discharge 180 LPM (3 LPS) / 10.8 M3/hr

Pumping Head : 70 M

(vii) Rate shall include inter connecting cables and cable box if reqd for cable

189 Diesel Engine Driven Fire Pump For Hydrant & Sprinkler System [Stand by pump) 1.00 Nos. 883750.00

Location - Plant Room

Providing, Installing, testing & commissioning of fire authority approved Diesel

Engine driven fire pump suitable for automatic/manual operations consisting of the

following: (i) Horizontal split casing, high pressure single/ multistage centrifugal

type fire pump having cast iron body, bronze impeller, stainless steel shaft &

capable of delivering 1620 LPM (27 LPS) against a total head of 70 M while

running at 2300 RPM complete with proper connection to suction and delivery line,

and including bypass arrangement for testing of pumps as per the requirement.

Mechanical seal shall be included, having a name plate indicating suction, delivery,

head, discharge, stages, RPM and direction of rotation. Stainers at pump input shall

be provided as per manufacturer requirements. Pump shall be capable of furnishing

not less than 150% of rated capacity at a head not less than 65% of the rated head.

The shut off head shall not exceed 120% of rated head.(ii) Water cooled heat

exchanger type diesel engine of required BHP or as per manufacturer at 1500 RPM

for the above pump complete with standard accessories & suitable cooling system

as described in specifications. (iii) Common base plate for mounting pump &

engine of required strength manufactured out of M.S. channels as per manufacture's

recommendation with heavy duty Anti Vibration pads. (Cushy foot) (6 nos., heavy

duty). (iv) Flexible Coupling & coupling guard for direct coupling of engine &

pump. (v) Suitable reinforced cement concrete pump foundations as per

manufacturer design including foundation bolts, washer as required. (vi) The

capacity of day oil tank shall be such that to allow the diesel engine to run on full

load for 2 hour storage tank of welded construction confirming to IS-2552. Tank

shall be provided with inlet, outlet, overflow, air vent, drain connections, filling

connection & magnetic level indicator. Tank shall be mounted on a suitable steel

structure (Painted with 2 coats of red oxide paint). Tank shall be provided with

epoxy coat from inside & two or more coats of synthetic enamel paint outside over

two coats of red oxide primer. Diesel storage tank shall be double skin. (vii)

valts 180 AH lead acid battery (12 volts - 2 Nos) with boost/Trickle charger for

starting the engine automatically complete as required.

Diesel Engine driven pump of Hydrant & Sprinkler System

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

190 Fire Pump panel (Combined for all Pumps) and electrical 1.00 Nos. 454500.00

works - starter panel with star delta or as per CFO

approved Starters rated to suite pump HP with necessary

protection features like SSP/ELR/OL/SC/ phase and on off

indicating lamps. The busbars shall be of AI - 0.8 A /

sqmm size. Panel shall be fabriated from 14G sheet steel

with svene tank process powder coated and shall be min IP

52. Panel shall have ammeter/Voltameter and KWh meter.

Cabling / Earthing from panel to pump shall be scope of

vendor without any extra cost. Cabling - supply / laying

and terminating the cables. Panel shall be rated min for

25KA fault level. Cable trays - hot dip GI ladder type

gauge with required supports shall be used for cabling.

Panel shall have one incomer MCCB/ACB of required

rating where by incoming supply and earthing shall be

terminated by electric colour.

191 Fire Pumps & Accessories, Yard Hydrant, Internal 1.00 Nos. 153924.00

Hydrant, Hose Reel & Sprinkler System Supply,

Installation, Testing & Commisioning of Main Fire Pump

Of Capacity 20 H.P. with 55 mtr. Head, Pump

192 Supply, Installation, Testing & Commisioning of control 1.00 Nos. 90900.00

Panel suitable for automatic operation of fire fighting

pumps consisting (a) Necessary cabling, wiring, earthing

from panel to individual equipment shall be included in the

quoted price. (b) Facility for more selection i.e. auto or

manual. (c) Protection failure and control cabling. (d)

Interlocking of pressure switch with pumps.

193 Supply, Installation, Testing & Commisioning of 150mm 1.00 Nos. 3535.00

dia. Pressure Gauge of range 0 - 15 kg/cm3 confirming to

as per specification complete as required.

194 Supply, Installation, Testing & Commisioning of Pressure 1.00 Nos. 4545.00

Switches for automation of fire pumps, Pressure switches

shall be double pole, single throw type suitable for 3 phase

supply with diaphragm. Alluminium Enclosure with IP

protection as required.

195 Supply, Installation, Testing & Commisioning of the 150.00 meter 2390.67

following sizes of flanges jointed / screwed / welded, M.S.

Pipes of Class C ISI marked including accessories such as

MS bracket, U clamps with Anchor Fasteners, tees /

elbows / reducers / couplings / unions / bends / flanges etc.

and laying on the surface including painting with two coats

of anticorrosive primer and two coats of approved red

enamel paint after laying and testing after installation etc.

as per specifications complete as required. a) 150 mm dia.

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

196 Supply, Installation, Testing & Commisioning of the 300.00 meter 1711.95

following sizes of flanges jointed / screwed / welded, M.S.

Pipes of Class C ISI marked including accessories such as

MS bracket, U clamps with Anchor Fasteners, tees /

elbows / reducers / couplings / unions / bends / flanges etc.

and laying on the surface including painting with two coats

of anticorrosive primer and two coats of approved red

enamel paint after laying and testing after installation etc.

as per specifications complete as required. a) 100 mm dia.

197 Supply, Installation, Testing & Commisioning of the 200.00 meter 1277.65

following sizes of flanges jointed / screwed / welded, M.S.

Pipes of Class C ISI marked including accessories such as

MS bracket, U clamps with Anchor Fasteners, tees /

elbows / reducers / couplings / unions / bends / flanges etc.

and laying on the surface including painting with two coats

of anticorrosive primer and two coats of approved red

enamel paint after laying and testing after installation etc.

as per specifications complete as required. c) 80 mm dia.

198 Supply, Installation, Testing & Commisioning of the 150.00 meter 1100.90

following sizes of flanges jointed / screwed / welded, M.S.

Pipes of Class C ISI marked including accessories such as

MS bracket, U clamps with Anchor Fasteners, tees /

elbows / reducers / couplings / unions / bends / flanges etc.

and laying on the surface including painting with two coats

of anticorrosive primer and two coats of approved red

enamel paint after laying and testing after installation etc.

as per specifications complete as required. d) 65 mm dia.

199 Supply, Installation, Testing & Commisioning of the 250.00 meter 989.80

following sizes of flanges jointed / screwed / welded, M.S.

Pipes of Class C ISI marked including accessories such as

MS bracket, U clamps with Anchor Fasteners, tees /

elbows / reducers / couplings / unions / bends / flanges etc.

and laying on the surface including painting with two coats

of anticorrosive primer and two coats of approved red

enamel paint after laying and testing after installation etc.

as per specifications complete as required. e) 50 mm dia.

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

200 Supply, Installation, Testing & Commisioning of the 200.00 meter 858.50

following sizes of flanges jointed / screwed / welded, M.S.

Pipes of Class C ISI marked including accessories such as

MS bracket, U clamps with Anchor Fasteners, tees /

elbows / reducers / couplings / unions / bends / flanges etc.

and laying on the surface including painting with two coats

of anticorrosive primer and two coats of approved red

enamel paint after laying and testing after installation etc.

as per specifications complete as required. f) 32 mm dia.

201 Supply, Installation, Testing & Commisioning of the 300.00 meter 555.50

following sizes of flanges jointed / screwed / welded, M.S.

Pipes of Class C ISI marked including accessories such as

MS bracket, U clamps with Anchor Fasteners, tees /

elbows / reducers / couplings / unions / bends / flanges etc.

and laying on the surface including painting with two coats

of anticorrosive primer and two coats of approved red

enamel paint after laying and testing after installation etc.

as per specifications complete as required. g) 25 mm dia.

202 Supply, Installation, Testing & Commisioning of C.I. 15.00 Nos. 9738.42

Butterfly valve (PN 1.6) with flanges, nut bolts, gaskets

complete as required. a) 150 mm dia.

203 Supply, Installation, Testing & Commisioning of C.I. 30.00 Nos. 8932.44

Butterfly valve (PN 1.6) with flanges, nut bolts, gaskets

complete as required. b) 100 mm dia.

204 Supply, Installation, Testing & Commisioning of C.I. 20.00 Nos. 5555.00

Butterfly valve (PN 1.6) with flanges, nut bolts, gaskets

complete as required. d) 50 mm dia.

205 Supply, Installation, Testing & Commisioning of Cast iron 20.00 Nos. 9090.00

Dual plate Check valve (PN 1.6) a) 150 mm dia.

206 Supply, Installation, Testing & Commisioning of Cast iron 25.00 Nos. 7564.90

Dual plate Check valve (PN 1.6) b) 100 mm dia.

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

207 Supply, Installation, Testing & Commisioning S.S. Single 12.00 Nos. 5656.00

Headed Fire Hydrant Valve with 80mm N.B. Flanged

inlet, 63 mm dia. Female instantaneous outlet type S.S.

coupling, blank cap, chain, twist release type lug & all

accessories Confirming to IS:5290. Including fixing with

supports, flanged tapping from wet riser, orifice plate.

208 Supply, Installation, Testing & Commisioning of Weather 15.00 Nos. 4595.50

proof standard M.S. Fire Hose Cabinet wall mounting type

(450mm x 450mm x 250mm deep) having single or double

opening with necessary locking arrangement by allan key

suitable for housing 1 nos. hose pipe, 1 nos. Branch pipe &

nozzle spanner.

209 Supply, Installation, Testing & Commisioning non 15.00 Nos. 5641.86

percolating rubber reinforced lined Fire Hose pipe (as per

IS:636) of 63mm dia and 15 mtr. Long. The hose shall be

rated for burst pressure pf 35.7kg/sqcm. Hose shall be

complete with ISI marked SS male & female coupling

(IS:903) bound & riveted to hose pipe with copper rivets &

1.5mm copper wire.

210 Supply, Installation, Testing & Commisioning of 63mm 6.00 Nos. 5641.86

dia. Instantaneous pattern SS 304, short branch pipe,

20mm dia nozzle confirming to IS

211 Supply, Installation, Testing & Commisioning of First Aid 6.00 Nos. 6565.00

Hose Reel equipment conforming to 15:884 comprising of

hose reel drum, 8 mm shut off noz:z.le, Ru bber hose of

mm dia x 30 mtr. long, painting, swinging type fixing

bracket, anchor fastener, bolts & nuts etc.

212 Supply, Installation, Testing & Commisioning of SS Ball 30.00 Nos. 858.50

Valve. A) 25mm dia.

213 Supply, Installation, Testing & Commisioning of Cast Iron 2.00 Nos. 8585.00

2 Way Fire Brigade Inlet as per 1S: 904 having 63 mm dia

in/et with blank cap and chain with necessary fit ti ngs,

flanges, nut bolts etc. complete as required. (For Hydrant

214 Supply, Installation, Testing & Commisioning of Gun 2.00 Nos. 959.50

Metal Air Release Valve with necessary fittings. Size:

25mm (For Riser)

215 Supply, Installation, Testing & Commisioning of 575.00 Nos. 454.50

Quartzoid Bulb type Sprinkler Heads. A) Pendent

216 Providing, Installation, testing and commissioning of 4 3.00 Nos. 378750.00

loop addressale type fire alarm panel which shall be

operated on 230 V, 50 Hz with battery charger & Battery.-

(Fire alarm repeater panel)

217 Manual Call Point 10.00 Nos. 454.50

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

218 2 core x 1.5 sqmm wire with pvc conduct and required 250.00 Rmt. 166.65

219 Providing, Installation, testing and commissioning of 250.00 Nos. 3787.50

addressable smoke detectors, it shall support base

mounted isolator modules and the detectors shall have led

for indication and output for response indicator complete

220 Getting Approval of Fire Hydrant System from local fire 1.00 Job 404000.00

authority and any other relevant statutary authority at intial

and various other stages of work, including preparation of

report/drawings as per fire authority. Contractor shall

include cost of all liason workwhich are not explicity

mentioned above but are mandatory to have fire authority

221 II) Fire Extinguisher and Exit Signages Supply, 30.00 Nos. 6447.84

installlation, testing and commissioning of Carbon

Dioxide (CO2) type Fire Extinguisher of 4.5 kg confirm to

IS:15683, with ISI marked / TAC approved fitted with

required accessories including wall suspension brakets.

222 Supply, Installation, Testing & Commisioning of ABC 30.00 Nos. 2222.00

type 6kg confirm IS:15683, with ISI marked / TAC

approved fitted with required accessories including wall

suspension brackets.

223 Providing AUTOGLOW Signages in block/ small letters 20.00 Nos. 858.50

of specified size (a) Fire Lift Size: 4" x 12"

224 Providing AUTOGLOW Signages in block/ small letters 20.00 Nos. 858.50

of specified size (b) Fire Hydrant : 4" x 12"

225 Providing AUTOGLOW Signages in block/ small letters 20.00 Nos. 858.50

of specified size (c) "DCP" Extingusher : 4" x 12"

226 Providing AUTOGLOW Signages in block/ small letters 20.00 Nos. 858.50

of specified size (c) "CO2" Extingusher : 4" x 12"

227 Providing, Installation, testing and commissioning of 15.00 Nos. 5504.50

addressable Looped power type manual break glass unit

with ressettable key

228 Providing, Installation, testing and commissioning of 10.00 Nos. 6565.00

addressable Looped power type Strobe combined hooters

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

229 P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 16.00 Sqmt 1311.19

mm (average) base of cement mortar 1:6 ( 1 cement:

coarse sand) on new surface or fixing on existing flooring

by adhesive material including dismentaling of existing

flooring and jointed with color cement slurry including

finised with flush pointing & cleaning the surface etc.

complete for light shade

230 Providing and laying Ceramic tiles 6mm thick in skrting 2.00 Sqmt 1090.32

risers of steps and dedo on 10mm thick cement plaster 1:3

(1-cement : 3-coarse sand) and jointed with white cement

231 Providing and fixing standared extruded of alluminium 1.00 Sqmt 1175.56

section of size 63mm x 38.10mm x 1.2mm @ Wt.

Kg/mt with colour anodized alluminium frame for

ventilation with 5 mm thick frosted glass as details etc

complete for Ventilation

232 Providing and fixing wash down water closet (European 1.00 Nos. 4864.35

type, W.C. Pan) with integral P or S trap, Health Fauset

Heavy Duty with hook and PVC dual flush tank with

complete fittings including jointing the trap with soil pipe

in Cement Mortar 1:1 (1-Cement : 1-fine sand) (Seal and

cover to be measured and paid for separately)(A) vitreous

China Pattern :(i) in white colour

233 Excavation for foundation upto 1.5 m depth including 477.00 Cum 212.53

sorting out and stacking of useful materials and

disposing off the excavated stuff upto 50 Meter lead.(A)

Loose or soft soil (Excavated by Manual Labour)

234 Excavation for foundation for depth from 1.5 m to 3.0 m 158.00 Cum 235.05

including sorting out and stacking of useful materials

and disposing off the excavated stuff upto

Meter lead.(A) Loose or soft soil (Excavated by

235 (i) Half brick masonry in common brunt clay building 33.00 Sqmt. 629.84

bricks having crushing strength not less than

Kg/Sq.Cm. in Cement mortar 1:4 (1- Cement : 4 -coarse

sand ) in foundation and plinth (B) Conventional

236 Providing and laying (to level or slopes) and jointing with 25.00 Rmt 317.48

stiff mixture of Cement Mortar in proportion 1:1 Salt

glazed stoneware pipes including testing of pipes and

joints complete.(B) 150mm dia.

237 Providing and Constructing sock pit of 4.46 mt. dia outside 4.00 Nos 177748.89

and 12 mt depth with honey combed masonary 6.50 mt.

from bottom and 0.60 mt. brick masonary in C.M. 1:6 top

with RCC slab cover of M200 vent pipe 1.8mt. Long

75mm dia & C.I. cover and cowel vent etc. comp

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

238 Constructing Manhole with R.C.C. top slab in 1:2:4 mix 5.00 Nos 23470.49

(1-cement :2-coarse sand : 4-graded stone aggregate 20mm

nominal size) foundation concrete 1:3:6 mix (1-cement : 3-

coarse sand :6-Brick bats 40 + 50mm size) inside

plastering 15mm thick with Cement Mortar 1:5 (1-Cement

: 5-coarse sand) finished with a floating coat of neat

cement and making channels in cement concrete 1:2:4 mix

(1-Cement :2-Coarse sand :4-stone aggregate 20mm

nominal size) finished smooth complete including curing

and festing (i) Inside size 900mm x 1200mm and 1.5M.

deep including C.I. cover with frame size 560mm diameter

total weight of cover and frame to be not less than 128 kgs.

(Wt. of cover 64 Kg. and Wt. of frame 64 Kg.)(A) With

230mm thick walls of brick msonry using brick having

crushing strength not less than 35Kg. / sq.cm. in Cement

Mortar 1:5 (1- Cement: 5-Coarse sand) (3) C type

depth 2.25 Metre for 150mm diameter sewer.

239 Providing corrugated G.I. sheet of class-3 roofing fixed 2332.00 Sqmt. 734.19

with glavanished iron J or L Hooks, Bolts and nuts 8mm

diameter with bitumen and G.I. limpet washer or G.I.

limpet washer. filled with white lead complete excluding

the cost of purlins, Rafters and Trusses.(1) 0.80 mm thick

240 Point wiring for Light / Bell with 2-1.5 sq.mm & earth 1193.00 Pts 485.81

wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires up to

10 mtr length , in below type of pipe erected with 6A

Modular type switch / bell push & accessories and earth

continuity of following type, erected on PVC /

Metallic/Wooden box, single mounting base frame

covered with textured/metallic/white front plate modules

erected on / in wall / ceiling as per pipe erected, with

necessary Lamp holder/ceiling rose / H.D.Connector as

directed.(f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling

complete.Cat-III (Make:- Anchor, Indoasian, L&T / LK,

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

241 Point wiring for Tissino / Modular secondary light point 823.00 Pts 167.66

with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (green) both

are of ISI marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires, in below type of pipe to be erected

complete with earth continuity and necessary connection

with primary light with accessories erected on Metal /

PVC / wooden box covered with 3 mm thick

PC(Polycarbonate) / Acrylic sheet for open / concealed

wiring. with necessary Lamp holder / ceiling rose /

H.D.Connector as directed.Note:- Maximum up to 6 mtrs

length, excess will be considered as Mains for Secondary

Point. (f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling complete

242 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 628.00 Pts 674.68

1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade

FRLS PVC insulated multi strand copper wires up to

mtr length, in below type of pipe erected with 6A

Modular type switch and hum free EME step type

electronic fan regulator mounted and accessories with

earth continuity of following type erected on PVC /

Metallic/Wooden box, single mounting base frame

covered with textured/metallic/white front plate modules

erected on / in wall / ceiling as per pipe erected. with

necessary ceiling rose / H.D.Connector as directed..(f) with

medium class Rigid PVC pipe and accessories erected

concealed in wall/ceiling complete.Cat-III (Make:-

Anchor, Indoasian, L&T / LK, Great-white )

243 Point wiring for Individual Plug with & earth wire of 1.5 222.00 Pts 510.05

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS

PVC insulated multi strand copper wires up to 10 mtr

length, in below type of pipe erected complete with

Modular type switch & 5 pin Plug erected on PVC /

Metallic/Wooden box covered with appropriate front plate

modules erected on / in wall / ceiling as per pipe erected

with following type of accessories. [I] For 6A Plug and 6 a

switch with 2-1.5 sq.mm Cu. Wire from nearby

switchboard/mcb db board (f) with medium class Rigid

PVC pipe and accessories erected concealed in

wall/ceiling completeCat-III (Make:- Anchor, Indoasian,

L&T / LK, Great-white )

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

244 Point wiring for on board Looped Plug with 6A Modular 484.00 Pts 257.55

type switch & 5 pin socket erected on PVC /

Metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate modules

erected on / in wall / ceiling with following type

accessories.Cat-III (Make:- Anchor, Indoasian, L&T / LK,

245 Providing following type of Modular Type Accessories 103.00 Nos. 160.59

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (3) Two Pin/RJ-11 Telephone

Socket[A] For One Gang Cat.III (Make:- Anchor,

Indoasian, L&T / LK, Great-white )

246 Providing following type of Modular Type Accessories 11.00 Nos. 160.59

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (4) TV Co-axial Socket outlet Cat-

III (Make:- Anchor, Indoasian, L&T / LK, Great-white )

247 Providing following type of Modular Type Accessories 482.00 Nos. 25.25

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (7) Blank Plate Single Cat.III

(Make:- Anchor, Indoasian, L&T / LK, Great-white )

248 Providing following type of Modular Type Accessories 271.00 Nos. 160.59

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (8) Computer RJ-45 socket Cat-III

(Make:- Anchor, Indoasian, L&T / LK, Great-white )

249 Providing following type of Modular Type Accessories 222.00 Nos. 180.79

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (9) 16 Amp. SP one way switch Cat-

III (Make:- Anchor, Indoasian, L&T / LK, Great-white )

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

250 Providing following type of Modular Type Accessories 222.00 Nos. 199.98

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (10) 6/16Amp. Universal socket Cat-

III (Make:- Anchor, Indoasian, L&T / LK, Great-white )

251 Providing and erecting ISI mark Medium class RIGID 13145.00 Mtrs. 33.33

PVC PIPES of following size complete to be erected on/in

wall or ceiling erected with necessary PVC fittings &

Junction boxes fixed with adhesive solution & Clamps

with following dia of pipes, in approved manner as

directed (b) 25 mm (Make:- Nihir, Vraj, BLP, Precision )

252 Providing and erecting ISI mark Medium class RIGID 295.00 Mtrs. 54.54

PVC PIPES of following size complete to be erected on/in

wall or ceiling erected with necessary PVC fittings &

Junction boxes fixed with adhesive solution & Clamps

with following dia of pipes, in approved manner as

directed (c) 32 mm (Make:- Nihir, Vraj, BLP, Precision )

253 Providing & erecting PVC Corrugated Flexible Conduit 225.00 Mtrs. 21.21

with required nos. of coupling, PVC bushes, Check-nuts

etc. complete of following sizes. (2) 25 mm

254 Providing & erecting PVC Corrugated Flexible Conduit 155.00 Mtrs. 27.27

with required nos. of coupling, PVC bushes, Check-nuts

etc. complete of following sizes.(3) 32 mm

255 Supplying and laying UPVC cable trunking system 270.00 Mtrs. 428.24

comprising unplasticised polyvinyl, chloride rigid material

with ignition free and flame proof confirming BS with

necessary end caps Internal and external bend, flat bends,

coupler, tee etc..All necessary accessories and measuring

of following sizes (2) 100 mm x 50 mm trunking (Make:-

Nihir, Vraj, BLP, Precision )

256 Providing and erecting Mains with 1.1 KV grade FRLS 16238.00 Mtrs. 82.82

PVC insulated ISI marked stranded Copper conductor wire

in following type of pipe to be erected concealed in

/flushed on wall/ceiling, with 1.5 sq. mm copper conductor

FRLS PVC insulated stranded wire of green colour for

earth continuity of following size (A) with medium class

Rigid PVC pipe and accessories (b) 2 wire 2.5 sq. mm

(Make:- Finolex, KEI, RR, Avocab)

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

257 Providing and erecting Mains with 1.1 KV grade FRLS 11856.00 Mtrs. 112.11

PVC insulated ISI marked stranded Copper conductor wire

in following type of pipe to be erected in / on wall / ceiling

with 2.5 sq. mm copper conductor FRLS PVC insulated

stranded wire of green colour for earth continuity of

following size (A) with medium class Rigid PVC pipe and

accessories (a) 2 wire 4 sq. mm (Make:- Finolex, KEI,

258 Providing and erecting Mains with 1.1 KV grade FRLS 3066.00 Mtrs. 180.79

PVC insulated ISI marked stranded Copper conductor wire

in following type of pipe to be erected in / on wall / ceiling

with 2.5 sq. mm copper conductor FRLS PVC insulated

stranded wire of green colour for earth continuity of

following size (A) with medium class Rigid PVC pipe and

accessories (g) 4 wire 4 sq. mm (Make:- Finolex, KEI,

259 providing and erecting Mains with ISI marked, 1.5KV 320.00 Mtrs. 91.91

grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms to

IS 694, IEC - 227 erected in existing pipe of following

size (Specifically for control panel, relays, power

switchgears, motor starters & control wiring) with required

size of copper lugs, nuts and bolts if required. (f) One wire

260 providing and erecting Mains with ISI marked, 1.5KV 460.00 Mtrs. 236.34

grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms to

IS 694, IEC - 227 erected in existing pipe of following

size (Specifically for control panel, relays, power

switchgears, motor starters & control wiring) with required

size of copper lugs, nuts and bolts if required. (h) One wire

261 providing and erecting Mains with ISI marked, 1.5KV 160.00 Mtrs. 300.98

grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms to

IS 694, IEC - 227 erected in existing pipe of following

size (Specifically for control panel, relays, power

switchgears, motor starters & control wiring) with required

size of copper lugs, nuts and bolts if required.(i) One wire

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

262 providing and erecting Mains with ISI marked, 1.5KV 56.00 Mtrs. 470.66

grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms to

IS 694, IEC - 227 erected in existing pipe of following

size (Specifically for control panel, relays, power

switchgears, motor starters & control wiring) with required

size of copper lugs, nuts and bolts if required. (j) One wire

263 Supplying and erecting Flexible PVC insulated multi 1426.00 Mtrs. 46.46

strand multi core 1.1 kv grade ISI marked copper wires of

following size to be erected as directed. e) 1.50 Sq.mm

core round PVC sheathed (Make:- Finolex, KEI, RR,

264 Providing & Erecting approved make following size of TV 495.00 Mtrs. 62.62

Co-axial flexible cable comprising inner conductor of solid

bare copper insulated with Foam PE & Secondary

conductor made of poly - Aluminium film bonded Al.

Braids @ suitable coverage overall sheathed with black

PVC insulation. e).RG-11

265 Supplying & erecting approved make Telephone Cable 2575.00 Mtrs. 20.20

electrolytic copper conductor PE insulation twisted in two

pairs, & wrapped with FRLS PVC tape & sheathed with

FRLS PVC or HFFR outer Jacket suitable for telephone

wiring & confirming to C-DOT erected in existing pipe. of

following size of conductors & nos.of pairs. With

necessary connections. [A] Conductor Size 0.5 mm (a)

Unarmoured 2) Two Pairs (Make:- Finolex, D-Link )

266 Supplying & erecting approved make Telephone Cable 240.00 Mtrs. 125.24

electrolytic copper conductor PE insulation twisted in two

pairs, & wrapped with FRLS PVC tape & sheathed with

FRLS PVC or HFFR outer Jacket suitable for telephone

wiring & confirming to C-DOT erected in existing pipe. of

following size of conductors & nos.of pairs. With

necessary connections. [A] Conductor Size 0.5 mm (b)

Armoured [Jelly Filled] (1) Ten Pairs (Make:- Finolex, D-

267 Supplying & erecting approved make LAN cable of 8672.00 Mtrs. 47.47

following size in existing pipe as per direction [C] CAT -

6 (Make:- Finolex, D-Link )

268 Providing & erecting main Distribution (MDF) indoor 9.00 Nos. 994.85

type, back mounted frame as per DoT standard approved

with krone strips (a) Suitable for 10 pair

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

269 Supplying & erecting M.S. Box having 16 Gauge painted 74.00 Nos. 88.88

with red oxide or Heavy duty PVC box erected flushed on

wall or concealed in wall with necessary plastering &

finishing as directed of following size. (c) 200 mm x

270 Providing & erecting Switch board for Computer or 271.00 Nos. 1133.22

electric apparatus consisting of following modular type

accessories mounted with PVC / Metallic concealed/open

box with single mounting base frame covered with

textured/metallic /white front plate,modules erected with

necessary connections as directed

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug For Modular Type

Accessories.Cat-III (Make:- Anchor, Indoasian, L&T / LK,

271 Decorative call bell Ting-tong box type 250 volts complete 93.00 Nos. 71.71

272 Supplying under floor pregalvanised corrosion proof 540.00 Mtrs. 765.58

rectangular sheet steel cable trunking of 1.6 mm thick

having with stand point load up to 1.33 Ton & free from

seepage of concrete of screed water with all

accessories,Junction Box,Joints as required and demanded

by engineer-incharge and laying/erecting as per OEM

guidelines and as per instruction of engineer incharge

having following size of dimensions and No of

compartments (W x D x T) Cat-III [10] 150mm x 38mm x

1.6mm with Three Compartments

273 Supplying under floor pregalvanised corrosion proof 270.00 Mtrs. 1342.29

rectangular sheet steel cable trunking of 1.6 mm thick

having with stand point load up to 1.33 Ton & free from

seepage of concrete of screed water with all

accessories,Junction Box,Joints as required and demanded

by engineer-incharge and laying/erecting as per OEM

guidelines and as per instruction of engineer incharge

having following size of dimensions and No of

compartments (W x D x T) Cat-III[13] 300mm x 38mm x

1.6 mm with Three Compartments

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

274 Supplying and erecting LED indoor fittings with LEDs of 86.00 Nos. 373.70

wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made

of thick sheet Steel conforming to IS: 513/CRCA/

aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company

mark/name 160V to 270V, Power Factor more than 0.95,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage capacity

of LED fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.) (A) Tube

Light with integral/ non-integral driver . (iv) 22-24 Watts,

Surge - 2KV,IP-20, conventional 4 feet Cat III (Make:-

Wipro,Havells, Philiphs,LT )

275 Supplying and erecting led lamps with following wattage 47.00 Nos. 112.11

capacity of 220 to 240 voltage, minimum 15000 burning

hours life, 500 V in built-surge protection,Polycarbonate

diffuser, mounting suitable for E14 / E27 / B22 lamp

holders, pf >= 0.5 (A) LED Lamps integral type, with PC

diffuser suitable LAMP holder (i) 5 to 8 watts Cat-III

(Make:- Wipro,Havells, Philiphs,LT )

276 Supplying and erecting LED indoor fittings with LEDs of 264.00 Nos. 589.84

wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made

of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder coated

and high U.V. & corrosion resistance with diffuser

housed in aluminium casted body with company

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage capacity

of LED fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.) (A) Square/

Circular shaped Surface/Recessed Mount Downlight with

provision for spring loaded mounting clips complete.IP20

(iii) 16-20 watts, Surge-2 KV Cat-III (Make:-

Wipro,Havells, Philiphs,LT )

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

277 Supplying and erecting LED indoor fittings with LEDs of 1450.00 Nos. 1794.77

wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made

of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder coated

and high U.V. & corrosion resistance with diffuser

housed in aluminium casted body with company

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage capacity

of LED fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.) (B) LED

Panel Light with provision for Plane front frame with

translucent cover fixed to housing complete.IP20 (vi)

watts, 24" x 24", Surge- 2KV Cat-III (Make:-

Wipro,Havells, Philiphs,LT )

278 Supplying and erecting LED street light / Flood light 25.00 Nos. 3345.12

fittings with High power White LEDs wattage of 3 Watt

and above assembled on single MCPCB, efficiency more

than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated and

heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened glass with

company mark/name engraved or embossed 160 to

V,Power Factor more than 0.95, THD < 10 %, CCT

K to 5700K,Uniformity ratio >0.45, Luminaire efficacy>

100 lumens/watt . LED driver efficiency > 85 %.( fittings

required LM-79 & LM-80 certificates)(NOTE: Below

description have shown ranges of Wattage capacity of

LED fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.) (A) Street

Light (IP-65), Surge protection -4KV integral and ,Light

must have 440VAC line supply with over-voltage

protection. (i) above 36 to 48 watts Cat-III (Make:-

Wipro,Havells, Philiphs,LT )

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

279 Supplying and erecting LED street light / Flood light 15.00 Nos. 6088.28

fittings with High power White LEDs wattage of 3 Watt

and above assembled on single MCPCB, efficiency more

than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated and

heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened glass with

company mark/name engraved or embossed 160 to

V,Power Factor more than 0.95, THD < 10 %, CCT

K to 5700K,Uniformity ratio >0.45, Luminaire efficacy>

100 lumens/watt . LED driver efficiency > 85 %.( fittings

required LM-79 & LM-80 certificates)(NOTE: Below

description have shown ranges of Wattage capacity of

LED fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.) (B) Flood

Light (IP-65), Surge protection -4KV integral and ,Light

must have 440VAC line supply with over-voltage

protection. (iii) Above 60 to 90 watts Cat-III (Make:-

Wipro,Havells, Philiphs,LT )

280 Supplying and erecting LED street light / Flood light 16.00 Nos. 8453.70

fittings with High power White LEDs wattage of 3 Watt

and above assembled on single MCPCB, efficiency more

than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated and

heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened glass with

company mark/name engraved or embossed 160 to

V,Power Factor more than 0.95, THD < 10 %, CCT

K to 5700K,Uniformity ratio >0.45, Luminaire efficacy>

100 lumens/watt . LED driver efficiency > 85 %.( fittings

required LM-79 & LM-80 certificates)(NOTE: Below

description have shown ranges of Wattage capacity of

LED fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.) (B) Flood

Light (IP-65), Surge protection -4KV integral and ,Light

must have 440VAC line supply with over-voltage

protection. (v) above 120 to 160 watts Cat-III (Make:-

Wipro,Havells, Philiphs,LT )

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

281 Supplying and erecting LED street light / Flood light 16.00 Nos. 4819.72

fittings with High power White LEDs wattage of 3 Watt

and above assembled on single MCPCB, efficiency more

than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated and

heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened glass with

company mark/name engraved or embossed 160 to

V,Power Factor more than 0.95, THD < 10 %, CCT

K to 5700K,Uniformity ratio >0.45, Luminaire efficacy>

100 lumens/watt . LED driver efficiency > 85 %.( fittings

required LM-79 & LM-80 certificates)(NOTE: Below

description have shown ranges of Wattage capacity of

LED fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.) (C) Post Top

Lantern LED fitting comprises of finish cast aluminum

spigot and spun aluminum canopy fixed with opal

polycarbonate, pipe arrangement for vertical mounting

driver and accessories wired upto terminal block.IP

(ii)32-40W Cat-III (Make:- Wipro,Havells, Philiphs,LT )

282 Providing and erecting Approved make Four pole moulded 115.00 Nos. 6173.12

case circuit breaker having breaking capacity ICU of

KA. at 415 V,having normal current rating up to 25 A to

100A. with Fixed thermal & magnetic release suitable to

work on A.C. supply 50 c/s. with all internal connections,

spreader tinned copper & complete erected in existing

G.M.S. housing. ICS=100% of ICU only Cat

III (Make:- Indoasian, L&T (LK), ABB, Schneider)

283 Providing and erecting Approved make Four pole moulded 51.00 Nos. 8055.76

case circuit breaker having breaking capacity ICU of

KA. at 415 V. having normal current rating 125A. with

Fixed thermal & magnetic release suitable to work on

A.C.supply 50 c/s. with all internal connections, spreader

tinned copper & complete erected in existing 16 G.M.S.

housing. ICS=100% of ICU only Cat III (Make:-

Indoasian, L&T (LK), ABB, Schneider)

284 Providing and erecting Approved make Four pole 27.00 Nos. 16221.61

moulded case circuit breaker having breaking capacity ICU

of 35 KA. at 415 V. having Normal current rating

200A.with variable Thermal & magnetic release suitable to

work on A.C.supply 50 c/s. with all internal connections,

spreader tinned copper & complete erected in existing

G.M.S.housing ICS=100% of ICU only Cat III

(Make:- Indoasian, L&T (LK), ABB, Schneider)

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

285 Providing and erecting Approved make Four pole moulded 18.00 Nos. 20946.39

case circuit breaker having breaking capacity ICU of

KA. and above at 415 V . having normal current rating

250A. with variable thermal & magnetic release suitable to

work on A.C.supply 50 c/s. with all internal connections,

spreader tinned copper & complete erected in existing

G.M.S. housing. ICS=100% of ICU only Cat III

(Make:- Indoasian, L&T (LK), ABB, Schneider)

286 Providing and erecting Approved make Four pole moulded 3.00 Nos. 25228.79

case circuit breaker having breaking capacity ICU of

KA and above at 415 V having Normal current rating

400A. with variable Thermal & magnetic release suitable

to work on A.C.supply 50 c/s. With all internal

connections, spreader tinned copper & complete erected in

existing 16 G.M.S. housing. ICS=100% of ICU only

Cat III (Make:- Indoasian, L&T (LK), ABB, Schneider)

287 Replaced old & U/S ACB Switch by Providing and erecting Approved 4.00 Nos. 178748.79

make standard EDO type Breaker with LSIG Ekip Touch, MP Rlease,

Modbus TCP Commmunication fixed type 4 Pole Air circuit breaker.

Having following kA breaking capacity with ICU=ICS=ICW (1

sec),Vsr=690 v, Ui=1kv with following type of relay and

accessories.(2) with microprocessor Release with over load, short

circuit, earth fault protection (L.S.I.G.) and metering display in

modular design with LED display and Test Trip button facility, CTs

and auxiliary contacts, of following current ratings. The MP release

shall have wide touch screen display with possibility to view the

maximum parameters. It shall also have bar graph with touch screen to

indicate individual phase loading and identify whether all phases are

evenly loaded. The protection release shall be suitable for

communication via Modbus TCP for incomer breaker and Modbus

TCP/RTU for outgoing breaker, without using any additional external

device or protocol converter. The Release should having Last 30 trips

and last 200 events. The protection release shall be suitable for

communication between LV & MV breaker as per IEC 61850.Note:-

ACB shall Have LSING basic protection in addition to it ACB shall

have power metering , modbus communication module as in- built part

of ACB release. ACB shall have Microswitch for indication. Price of

ACB included all necessary indication lamp like phase indication,

breaker on-off and trip indication etc. TNC Switch and other necessary

control wiring. (a) 800 Amp 50kA Cat III (Make:- Indoasian, L&T

(LK), ABB, Schneider)

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

288 Providing and erecting Approved make Earth fault Relay 30.00 Nos. 4983.34

suitable to mount with inter connection suitable to

following size of moulded case circuit breaker having CT

ratio & MCCB rating as following along with shunt trip

220V AC. with all internal connections & complete

erected in existing M.S.housing.(2) 125 A -200 A , CT

Ratio 1/200 (Make:- Indoasian, L&T (LK), ABB,

289 Providing and erecting Approved make Earth fault Relay 11.00 Nos. 5415.62

suitable to mount with inter connection suitable to

following size of moulded case circuit breaker having CT

ratio & MCCB rating as following along with shunt trip

220V AC. with all internal connections & complete

erected in existing M.S.housing. (3) 250 A -400 A , CT

Ratio 1/400 (Make:- Indoasian, L&T (LK), ABB,

290 Supplying and erecting triple pole & neutral 440V / 500V 148.00 Rn.Mtrs 1961.42

panel mounting Copper Busbars with four equal Nos. of

electrolyte bus having current density not more than

Amp. / sq.mm (Rated current / cross section area) duly

wrapped with colour insulating tape for phase sequence of

following current carrying capacity, erected with necessary

bus bar supports /insulators, main cable socket to each bar,

erected in existing cubical panel with necessary

connections. (A) Suitable for 100 Amp. Capacity

291 Supplying and erecting triple pole & neutral 440V / 500V 31.00 Rn.Mtrs 3202.71

panel mounting Copper Busbars with four equal Nos. of

electrolyte bus having current density not more than

Amp. / sq.mm (Rated current / cross section area) duly

wrapped with colour insulating tape for phase sequence of

following current carrying capacity, erected with necessary

bus bar supports /insulators, main cable socket to each bar,

erected in existing cubical panel with necessary

connections. (B) Suitable for 200 Amp. capacity

292 Supplying and erecting triple pole & neutral 440V / 500V 18.00 Rn.Mtrs 4909.61

panel mounting Copper Busbars with four equal Nos. of

electrolyte bus having current density not more than

Amp. / sq.mm (Rated current / cross section area) duly

wrapped with colour insulating tape for phase sequence of

following current carrying capacity, erected with necessary

bus bar supports /insulators, main cable socket to each bar,

erected in existing cubical panel with necessary

connections. (C) Suitable for 300 Amp. capacity

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

293 Supplying and erecting triple pole & neutral 440V / 500V 3.00 Rn.Mtrs 7319.47

panel mounting Copper Busbars with four equal Nos. of

electrolyte bus having current density not more than

Amp. / sq.mm (Rated current / cross section area) duly

wrapped with colour insulating tape for phase sequence of

following current carrying capacity, erected with necessary

bus bar supports /insulators, main cable socket to each bar,

erected in existing cubical panel with necessary

connections. (D) Suitable for 400 Amp. capacity

294 Supplying and erecting triple pole & neutral 440V / 500V 10.00 Rn.Mtrs 13199.69

panel mounting Copper Busbars with four equal Nos. of

electrolyte bus having current density not more than

Amp. / sq.mm (Rated current / cross section area) duly

wrapped with colour insulating tape for phase sequence of

following current carrying capacity, erected with necessary

bus bar supports /insulators, main cable socket to each bar,

erected in existing cubical panel with necessary

connections. (F) Suitable for 800 Amp. capacity

295 providing and erecting Miniature circuit breaker single 72.00 Nos. 270.68

pole 0.5A to 2A system and having breaking capacity

KA to be erected in existing box. confirming to IS

8828/1996 with ISI Mark Cat.III (Make:- Indoasian,

L&T (LK), ABB, Schneider)

296 Providing and erecting Miniature circuit breaker single 1362.00 Nos. 112.11

pole 6A to 25A suitable to operate on 240 V A.C. system

and having breaking capacity 10 KA to be erected in

existing box. confirming to IS 8828/1996 with ISI Mark

Cat-III (Make:- Indoasian, L&T (LK), ABB, Schneider)

297 Providing & erecting 240 V MCB double pole switch for 58.00 Nos. 295.93

lighting Load (B Curve) having 10 KA breaking capacity

& confirms to IS : 8828 in existing box having following

capacity (B) 40 Amp. Cat-III (Make:- Indoasian, L&T

(LK), ABB, Schneider)

298 Providing & erecting 415 V MCB Four Pole for Motor & 102.00 Nos. 737.30

Inductive Load (C Curve) having 10KA breaking capacity

& confirms to IS :8828 in existing box having following

capacity (B.) for 63 Amp. Cat-III (Make:- Indoasian,

L&T (LK), ABB, Schneider)

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

299 Providing and erecting Sheet Steel powder coated MCB 7.00 Nos. 1492.78

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to IS

8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of

same company of MCB to be used) suitable for(A) single

phase incoming and horizontal single phase outgoing (b)

sheet steel double door (IP-43) (iv)12 way (Make:-

Indoasian, L&T (LK), ABB, Schneider)

300 Providing and erecting Sheet Steel powder coated MCB 73.00 Nos. 3412.79

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to IS

8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of

same company of MCB to be used) suitable for (B) three

phase incoming and single phase horizontal type outgoing

Per phase isolation type (PPI) (b) sheet steel double door

(iii)8 way (Make:- Indoasian, L&T (LK), ABB, Schneider)

301 Providing and erecting Approved make RCCBs 226.00 Nos. 2235.13

conforming to IS: 12640 and having sensitivity of 30 mA

and Short Circuit withstand capacity of 10 KA and suitable

for operation on single phase 240 V,50Hz. having

characteristic of quick action & tripping with all advance

feature & do not incorporate any electronic component. for

following Max. rating erected as directed (iI) 40 Amps.DP

Cat. III (Make:- Indoasian, L&T (LK), ABB, Schneider)

302 Providing and erecting metallic vitrified danger notice 17.00 Nos. 69.69

board as per language suggested by engineer incharge for

MEDIUM VOLTAGE installation to be erected as per IS-

303 Providing and erecting Annealed bare Copper wire 8 to 16 130.00 Kgs. 794.87

304 Providing and erecting Pipe type earthing having 150 41.00 Nos. 368.65

cms.long and 2.5 cms. dia. galvanised iron pipe with

coupling and buch buried in specially prepared earth pit

complete with necessary 8 SWG earth wire.

305 For using salt and charcoal / coke as required for pipe type 41.00 Nos. 171.70

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

306 Supplying & erecting earth pit of minimum bore 42.00 Nos. 4591.46

dia.150mm size approved make Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-1987

made of corrosion free hot dipped G.I.Pipes having Outer

pipe dia of 50mm having 80-200 Micron galvanising,

Inner pipe dia of 25 mm having 200-250 Micron

galvanising, connection terminal dia of 12mm with

constant ohmic value surrounded by highly conductive

compound with high charge dissipation suitable for

following type of applications with chamber and heavy

duty cover. (A)(approved make OEM has to submit test

certificate including value of earth resistance of

installation duly stamped and signed by agency and officer

Incharge has to ensure the value of earthing resistane

mentioned in test Certificate) & having back filling

compound of (B) Inner chemical (CCM Compound)-

Resistivity:- 0.2 ohm / meter testing as per IEC 62561-

2017, Voltage drop:- < 1 volt at no load & dry form,

Sulphar content:- <2%(C) Back fill Compound :- Earthing

compound should be capable to retain moisture for long

time Necessary test report must be submitted by Agency.

(a) For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

307 Providing & erecting weather proof, dust & vermin proof, floor 20.50 Sq.Mtrs. 14902.55

mounted front operated indoor type cubical panel board

necessary IP-42 and above protection as per approval from

engineer incharge made from 14 SWG thick CRC M.S. sheet

for outer body & doors, 16 SWG thick CRC M.S.sheet for

internal partitions with necessary accesories , supporting

angles/ flats channel including cutting, bending, drilling,

welding, riveting with internal partitions & cable alley as per

requirements & instruction of engineer-in-charge with erection

of supplied switch gears, BUSBARS, suitable size of inter

connecting PVC copper wire / copper-aluminium strips, rubber

grommets, rib, bakelite control fuses/MCB for measuring

instruments, earth bus & earth bolts, foundation flange - bolts-

base Plates, sufficient nos. of hinged doors, handles with

locking arrangement and rubber gasket,heavy duty end terminal

connection,danger notice board,necessary ventilation,earthing

strip complete. The Panel shall be painted with epoxy powder

coating. (The rates excludes the cost of switchgears, bus bars,

inter connecting mains & Copper Aluminium strips, meters,

Fuses etc. The dimension shall be measured excluding base

beams) The panel shall be supplied with following approved

manufacturers with following size.(B) The standard companies

switch gear shall be used and only manufacturers at CPRI

approved factory (i) with 350mm depth

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

308 Providing & erecting weather proof, dust & vermin proof, floor 8.00 Sq.Mtrs. 40999.94

mounted front operated indoor type cubical panel board

necessary IP-42 and above protection as per approval from

engineer incharge made from 14 SWG thick CRC M.S. sheet

for outer body & doors, 16 SWG thick CRC M.S.sheet for

internal partitions with necessary accesories , supporting

angles/ flats channel including cutting, bending, drilling,

welding, riveting with internal partitions & cable alley as per

requirements & instruction of engineer-in-charge with erection

of supplied switch gears, BUSBARS, suitable size of inter

connecting PVC copper wire / copper-aluminium strips, rubber

grommets, rib, bakelite control fuses/MCB for measuring

instruments, earth bus & earth bolts, foundation flange - bolts-

base Plates, sufficient nos. of hinged doors, handles with

locking arrangement and rubber gasket,heavy duty end terminal

connection,danger notice board,necessary ventilation,earthing

strip complete. The Panel shall be painted with epoxy powder

coating. (The rates excludes the cost of switchgears, bus bars,

inter connecting mains & Copper Aluminium strips, meters,

Fuses etc. The dimension shall be measured excluding base

beams) The panel shall be supplied with following approved

manufacturers with following size.(B) The standard companies

switch gear shall be used and only manufacturers at CPRI

approved factory (iv) with 1000 mm. depth

309 Providing , erecting , fabricating the M.S. structure as per 695.00 Kgs. 77.77

requirement on site incorporating proper size of M.S.

angles,square,round, flats, bars, channels, sections

complete with cutting, welding, grinding & finishing duly

painted with one coat of red oxide with erection on site as

per direction of engineer in charge with necessary

grouting, cementing, plastering & finishing complete.

310 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured 460.00 Mtrs. 79.79

cable Aluminium conductor for 1.1 KV. to be laid on

wall with necessary clamps or in existing trench / pipe of

following size of cables. (A) 2 core 4 Sq. mm (Make:-

Finolex, KEI, RR, Avocab)

311 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured 280.00 Mtrs. 220.18

cable multistrand Aluminium conductor for 1.1 KV. to be

laid on wall with necessary clamps or in existing trench /

pipe of following size of cables (B) 3 1/2 core 35 Sq. mm

( 16 Sq. mm 1/2 core) (Make:- Finolex, KEI, RR,

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

312 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured 450.00 Mtrs. 284.82

cable multistrand Aluminium conductor for 1.1 KV. to be

laid on wall with necessary clamps or in existing trench /

pipe of following size of cables (C) 3 1/2 core 50 Sq.

mm ( 25 Sq.1/2 mm core) (Make:- Finolex, KEI, RR,

313 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured 990.00 Mtrs. 490.86

cable multistrand Aluminium conductor for 1.1 KV. to be

laid on wall with necessary clamps or in existing trench /

pipe of following size of cables (E) 3 1/2 core 95 Sq. mm

( 50 Sq. mm 1/2 core) (Make:- Finolex, KEI, RR,

314 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured 2520.00 Mtrs. 540.35

cable multistrand Aluminium conductor for 1.1 KV. to be

laid on wall with necessary clamps or in existing trench /

pipe of following size of cables (F) 3 1/2 core 120 Sq. mm

( 70 Sq. mm 1/2 core) (Make:- Finolex, KEI, RR,

315 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured 1295.00 Mtrs. 904.96

cable multistrand Aluminium conductor for 1.1 KV. to be

laid on wall with necessary clamps or in existing trench /

pipe of following size of cables (H) 3 1/2 core 185 Sq.

mm ( 95 Sq. mm 1/2 core) (Make:- Finolex, KEI, RR,

316 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured 1025.00 Mtrs. 117.16

cable multistrand / Solid Aluminium conductor for

KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables (A)

core 4 Sq. mm (Make:- Finolex, KEI, RR, Avocab)

317 Making trench in soft soil of suitable width of 90 cm deep 3105.00 Mtrs. 55.55

for laying cable or locating the fault all over the run and

back filling the same and making the surface as normal

318 Making trench in Hard Murrum / Tar Road of suitable 1552.00 Mtrs. 74.74

width of 90 cm or required depth for laying any size of

cable or locating the fault all over the run and back filling

the same and making the surface as normal ground.

319 Making trench in Hard Murrum / Tar Road of suitable 621.00 Mtrs. 357.54

width of 90 cm or required depth for laying any size of

cable or locating the fault all over the run and back filling

the same and making the surface as normal ground.(B) If

additional machinery like hammer driller or JCB use [Add]

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

320 Providing & laying. R.C.C. Hume pipe for cable to be laid 938.00 Mtrs. 263.61

90 cm. below ground across the road crossing or on floor

with necessary material in an approved manner and

making the ground as per original. (E)150 mm dia

321 Providing & laying approved make Double walled 1585.00 Mtrs. 62.62

corrugated pipes (DWC) of polyethylene(conforming to IS

14930 II )with necessary connecting accessories of same

material at required depth in existing trench for laying of

cable. below ground / road surface for enclosing cable

(A) 50 mm Outer Dia

322 Providing & laying approved make Double walled 2983.00 Mtrs. 137.36

corrugated pipes (DWC) of polyethylene(conforming to IS

14930 II )with necessary connecting accessories of same

material at required depth in existing trench for laying of

cable. below ground / road surface for enclosing cable

(D) 120 mm Outer Dia

323 Providing & laying approved make ISI marked Rigid 200.00 Mtrs. 236.34

PVC pipe having 6Kg / cm2 (Class-3) to be erected at road

crossing on or floor as directed for laying of cable. The

pipes as following size of dia & weight per 6 mtr. (F)

mm inner Dia. (11.63 Kg/6 RMT)

324 Providing and, fixing heavy duty flange type brass cable 114.00 Nos. 33.33

gland with rubber ring for PVC insulated armoured cable

complete with out going tails, insulating tape etc for

following size of cables. (A) 2 to 4 core 2.5 / 4 Sq. mm

325 Providing and, fixing heavy duty flange type brass double 6.00 Nos. 75.75

compression type cable gland with rubber ring for PVC

insulated armoured cable complete with out going tails,

insulating tape etc for following size of cables. (B) 3 & 1/2

326 Providing and, fixing heavy duty flange type brass double 8.00 Nos. 75.75

compression type cable gland with rubber ring for PVC

insulated armoured cable complete with out going tails,

insulating tape etc for following size of cables. (B) 3 & 1/2

327 Providing and, fixing heavy duty flange type brass double 40.00 Nos. 131.30

compression type cable gland with rubber ring for PVC

insulated armoured cable complete with out going tails,

insulating tape etc for following size of cables. (D) 3 & 1/2

328 Providing and, fixing heavy duty flange type brass double 37.00 Nos. 140.39

compression type cable gland with rubber ring for PVC

insulated armoured cable complete with out going tails,

insulating tape etc for following size of cables. (E) 3 &

1/2 core 120 Sq. mm

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

329 Providing and, fixing heavy duty flange type brass double 17.00 Nos. 238.36

compression type cable gland with rubber ring for PVC

insulated armoured cable complete with out going tails,

insulating tape etc for following size of cables. (G) 3 & 1/2

core 185 Sq. mm

330 Solder less crimping type Aluminium lugs conforming to 456.00 Nos. 6.06

IS suitable for cable of following size evenly crimped with

high pressure tool & connected to switchgear terminals

with brass/cadmium plated nut bolts in an approved

manner. (A) 1.5/ 2.5/4/6 Sq.mm

331 Solder less crimping type Aluminium lugs conforming to 24.00 Nos. 20.20

IS suitable for cable of following size evenly crimped with

high pressure tool & connected to switchgear terminals

with brass/cadmium plated nut bolts in an approved

manner. (D) 35 Sq.mm.

332 Solder less crimping type Aluminium lugs conforming to 32.00 Nos. 20.20

IS suitable for cable of following size evenly crimped with

high pressure tool & connected to switchgear terminals

with brass/cadmium plated nut bolts in an approved

manner. (D) 50 Sq.mm.

333 Solder less crimping type Aluminium lugs conforming to 160.00 Nos. 40.40

IS suitable for cable of following size evenly crimped with

high pressure tool & connected to switchgear terminals

with brass/cadmium plated nut bolts in an approved

manner. (F) 95 Sq.mm.

334 Solder less crimping type Aluminium lugs conforming to 148.00 Nos. 45.45

IS suitable for cable of following size evenly crimped with

high pressure tool & connected to switchgear terminals

with brass/cadmium plated nut bolts in an approved

manner. (G) 120 Sq.mm.

335 Solder less crimping type Aluminium lugs conforming to 68.00 Nos. 80.80

IS suitable for cable of following size evenly crimped with

high pressure tool & connected to switchgear terminals

with brass/cadmium plated nut bolts in an approved

manner. ( I ) 185 Sq.mm.

336 Providing and fixing approved make Perforated C type 110.00 RMtrs. 622.16

cable tray. Made from sheet steel. The cable tray should

be single or double bended as per required and as per IS

2062/1079 and shall be coated with hot dip galvanizing as

per IS 2629/4759. with max 17.5% perforation with

coupler plate / Fish plate and GI hardware like nut - bolt

and washers etc. erection with necessary support(

included) as per Specification and as per instruction of

engineer in charge..(5) 300 X 50 X 2.0 mm Thick

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

337 Providing and erecting Approved make Ceiling fan with 628.00 Nos. 1596.81

double ball bearing ISI mark with condenser A.C.

23OV.50 c/s.1200 mm. sweep complete, canopy erected

on existing hook or clamp with earthing. [Make shall be

approved by Engineer in charge] (Make:- Crompton,Orient

338 Supplying and erecting 19 / 20 mm. nominal bore Medium 628.00 Mtrs. 108.07

Class M.S. Pipe down rod erected duly painted for fan

complete with proper insulation without leckage and

339 Supplying & erecting fan hook box of 10 mm M.S. round 628.00 Nos. 108.07

bar bounded to the RCC bars up to 50mm length each side

and pierced through a 16 Gauge M.S. box / Heavy Duty

PVC box complete erected concealed in Ceiling with

necessary finishing.

340 Supplying & erecting approved make low noise decorative 76.00 Nos. 1366.53

exhaust fan having square frame ABS body with inbuilt

lowers & square frame. 250mm with 1350 RPM Cat.II

(Make:- Crompton,Orient )

341 Supplying and erecting approved make Octagonal pole 16.00 Nos. 4237.96

made from HR sheet steel. The pole should be made as per

IS. and shall be coated with hot dip galvanizing as per IS

2629/2633/4759, suitable suspend local wind speed with

integral Junction box consist of terminal plate of min 6mm

Hylam sheet, standard profile 35mmX7.5mm Din-Rail for

MCB Mounting, stud type terminal and arrangement for

cable termination to be erected With Suitable foundation

(Included) as per details given by manufacturer

considering site requirement. (A) 3 Mtr. Long 70 mm Top

X 130 mm bottom dia.3 mm thickness with

200mmX200mmX12mm base plate, 4-M16 Bolts and

450mm long with necessary G.I. J Bolts .Approx weight

29 kg (Make:-Ambica, Translend, Bajaj)

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit to estimated

342 Supplying and erecting approved make Octagonal pole 25.00 Nos. 8192.11

made from HR sheet steel. The pole should be made as per

IS. and shall be coated with hot dip galvanizing as per IS

2629/2633/4759, suitable suspend local wind speed with

integral Junction box consist of terminal plate of min 6mm

Hylam sheet, standard profile 35mmX7.5mm Din-Rail for

MCB Mounting, stud type terminal and arrangement for

cable termination to be erected With Suitable foundation

(Included) as per details given by manufacturer

considering site requirement. (D) 6 Mtr. Long 70 mm Top

X 135 mm bottom dia, 3 mm thickness with

200mmX200mmX12mm base plate, 4-M20 Bolts and

600mm long with necessary G.I. J Bolts .Approx Pole

weight 59 kg (Make:-Ambica, Translend, Bajaj)

343 Supplying & erecting approved make SMC press 4.00 Nos. 515.10

moulded composite FRP. loop-in, loop-out approx. 2mm

thick box complete with Bakelite connector strip

5way(3P+N+E),DIN rail for mounting mob & hinged

doors as per requirement having locking arrangements

with mounting clamp with nuts, bolts & washers suitable

for erection on pole with cable clamps& earth bolt of

following size of box. (b) 250mm x 200mm x 100mm

344 Providing street light pole bracket comprising main B 25.00 Nos. 561.56

Class MS pipe of 4.2 cm/require outside dia. complete

with suitable B Class M.S. sleeve tubing of approx.

45cms.length and suitable for 76.5 mm / 80mm. / require

size pole top having sufficient fastners for fixing the

brackets and having spread of 1 mtr. length with suitable

rise as per site condition & suitable welded stiffener