Recovery and Reconstruction of SPT Bridge No. 2/1 on Lakhipur Tulshibari road along with approaches protection under NDRF (PDNA 2022) for the year 2025-26 of Goalpara District (13-Goalpara West LAC) under Goalpara West and Dudhnoi TR Division.

Labour for dismantling all members of the timber bridge (excluding piles) with necessary scaffolding, jati bamboos, jumper ropes etc, complete and stacking them at suitable places as directed (all members will be under custody of the contractor till taken over by the department)

Supplying and driving timber piles of 25cm to 30cm diameter, dressed to heart wood including making length in every 30 cm interval, coal tarring two (2) coats with best tar applied hot (Rate inclusive of the cost of the required quantity of tar.) (A) Using Sal Timber (a) Mechanically with Rod monkey and crab winch (i) Portion of pile actually driven underground.

Supplying and driving timber piles of 25cm to 30cm diameter, dressed to heart wood including making length in every 30 cm interval, coal tarring two (2) coats with best tar applied hot (Rate inclusive of the cost of the required quantity of tar.) (A) Using Sal Timber (a) Mechanically with Rod monkey and crab winch (i) Portion of pile remaining above ground.

Scarfing and joining piles 25 cm to 30 cm diameter, dressed to heartwood of 90 cm in length includng supplying, fitting and fixing with 2 nos. of 50mm x 10mm MS FI clamps and 16 mm dia MS bolts and nuts etc. complete as directed. (Timber for piles and coal tarring shall be measured and paid separately.)

Supplying, fitting and fixing timber beam and bearing beam rectangular in size fitted with M.S. etc. supplying spikes etc. as necessary and coal tarring two (2) coats with best tar applied hot as directed (Rate inclusive of cost of the required quantity of tar) (a) Using Sal Timber

Supplying fitting and fixing "U" shaped flat iron strap making 0.5m x 0.3m size from 150mm x 12mm size MS flat including providing 10 bolts holes and fitting with 0.35m long 20mm dia MS bolts including fitting tightly with bearing beam, pile and RSJ beams etc. complete as directed.

Wood work including supplying , fitting and fixing complete with necessary M.S. bolts, nuts, nails, screw etc. and coal tarring two (2) coats with best tar applied hot (Rate is inclusive of the cost of the required quantity of tar.) Using Sal Wood (a) Underssed in floor planks, collars, bracing, standards, wheel guards, struts and railings, runner belts, rail, posts etc.

Wood work including supplying , fitting and fixing complete with necessary M.S. bolts, nuts, nails, screw etc. and coal tarring two (2) coats with best tar applied hot (Rate is inclusive of the cost of the required quantity of tar.) Using Sal Wood (b) In track way planks (alternate nailing to be done with decking in a seggragate way.)

Wood work including supplying , fitting and fixing complete with necessary M.S. bolts, nuts, nails, screw etc. and coal tarring two (2) coats with best tar applied hot (Rate is inclusive of the cost of the required quantity of tar.) B. Using Azar/ Nahar/ Nageswar/ Zarul Wood (a) Undressed in floor planks, collars, bracing, standards, wheel guards, struts and railings, runner belts, rail, posts etc

Construction of Embankment with Material Obtained from Borrow Pits Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and comp g actin to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5. (I) Private Land

Construction of Subgrade and Earthen Shoulders Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1.

Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508. Case - I: By Manual Means (i) Bitumen (S-90)

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510 By Manual Means (i) Bitumen (S-90)

Single bamboo palasiding / walling of whole 2nd class bamboo (Jati or Bethua) 75mm dia and closely packed & driven including fitting fixing with half bamboo kamis horizontally in three rows with cane or tying with wire complete and struts 1.5 m apart longitudinally and providing brush wood as per drawing and technical specifications Clause 1302.5

Providing and dumping of Sand filled cement bags including at proper place and position as directed by the Department

Restoration of SPT Br. No. 2/1 on Lakhipur Tulshibari road by clearing the debrises like water hyacinth, uprooted banaba tree and uprooted bamboo trees floating away from upstean side which stuck at bridge piles causing distruption to floe the water by cutting with suitable tools and pulling the debrises and water hyacinth to the bank of river, binding with coir string from the floating boat.

Geo Bag : Supplying, filling and laying in loose with Geo-textile bags of Type-A (1.30m x 0.70m) made of Geo textile non woven fabric sheets of 400 GSM manufactured from polyster/ polypropylene conforming to relevant ISO standard filled with specified sand/ silt from flood plain or adjacent char within a distance of 90 m of the work site including excavation, filling Geo bags with sand weighing 126.00 kg after filling, stitching the mouth of the filled bags with polypropylene or polyster complete as per technical specifications and as directed. (b) Without boat

Supply, Stitching and Laying of Non wooven Geo textile Fabric sheet of 400 gsm

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801 (iv) 800 X 600mm rectengular

Please Enable Macros to View BoQ information