PROVN OF FIRE POINT WITH SHED QTY 06 AND FIRE POINT WITH METALIC BOARD PLATFORM QTY 14 AT KUDDANKULAM AND MUKKUNNIMALA UNDER GE AF TRIVANDRUM

Amount

Schedule A

M&Lfor Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep in any type of soil complete all as specified and directed.

M&L for excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out hard/ dense soil complete all as specified and directed.

M&L for volumetric and nominal mix concrete pcc 1:2:4 type B-2 M-15 as in foundation complete all as specified and directed.

M&L for Pre-cast cement concrete block masonry C1 (1:3:6) using 20mm graded stone aggregate with solid blocks, exc. 10 cm in width and setting in mortar 1: 6 , complete all as specified and directed.

M&Lfor Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

Mild for steel TMT bars 8 mm dia and over, cut to length, bent to shape reqd, incl cranking, bending spirally for hooping for columns, hooling ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for B1 1:2:4 (20mm graded stone aggregate)for Foundations, including rafts, footings; bases for columns, etc.; basement slabs, under reamed piles and mass concrete Tcomplete all as specified and directed.

M&L Hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface (stone boulder) complete all as specified and directed.

M&L for Removing of Rock,soil excavated material n exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

M&L for Cement concrete type B-2, 1:2:4 (40mm graded stone aggregate)100mm thick as in sub base,sub floor , floors and pavings etc complete all as specified and directed.

M&L for Cement concrete type B-1, 1:2:4 (20mm graded stone aggregate)25mm thick as in sub base,sub floor , floors and pavings etc and finished with red coloured cement mortar 1:2 topping including finishing complete all as specified and directed.

M&L for Rendering 10mm thick on fair faces of brick/concrete surfaces or in CM 1:4 finished even & smooth without using extra cement complete all as specified and directed.

M&L for painting fire resisting paint single coat on surfaces of any description wood, steel, iron, concrete, brick, stone, etc., exceeding 10cm in width or girth complete all as specified and directed by Engr in charge

S&F 0.50mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed.

S&F 0.50mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screw and washers, in roofs, walls etc with grade of zinc coating 275 if fixed with L-type or J-type or cranked hook bolts in lieu of screws complete all as specified and directed.

S&F Fe 410 Gde E-250 Quality A Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and directed.

S&F Fe 410 Gde E-250 Quality A Plain sheet, girder or single stanchions, built up of one beam of channel section with flange plates, caps, bases, splices, angle brackets, cleats and other connections complete all as specified and directed.

M&L for welding , exc 2.5cm but n exc 5cm in length and thickness of metal to be welded not exc 6 mm complete all as specified and directed.

M&L for two coats of synthetics enamel paint on steel surfaces over one coat of red oxide primer incl preparation of new steel surfaces complete all as specified and directed.

M&L for Writing letters or figures (Block, Roman, Italic or Indian) n exc 30 cm high complete all as specified and directed.

M&L for Cutting in edges to line, to paint work of different tints (last coat only), where not otherwise provided complete all as specified and directed.

M&L for writing Index hands (natural size) or arrows (upto 40cm long) complete all as specified and directed.

M&L for writing Stops, commons, short lines, dashes, hyphens, brackets, etc.complete all as specified and directed.

M&L Chequered cement concrete tiles 30cm x 30cm x 25mm thick, powder coated colour set, jointed and pointed in neat cement slurry with grey cement and no pigment in floors complete all as specified and directed .

M&L screed bed or bedding layer of mortar 20 mm thick for laying floor finishes in CM 1:4 complete all as specified and directed.

M&L for PCC 1:4:8 type D-2, 40 mm graded stone aggregate Cement concrete in foundations, exc 100mm thikness filling complete all as specified and directed. (M-7.5 graded)

M&L Providing Cement concrete Type B1 1:2:4 (20mm graded stone aggregate) as in,bed block, copings and levelling concrete slightly rounded or chamfered angles and throating complete all as specified and directed.

DJ GROUP

KENZ CONSTRUCTIONS

DEFT GROUP ELECTROMECHANICAL