Repairs/Renovation of Building No.147/F-2 section in Filling Area at OFK.

Amount

Demolition of brickwork built in lime mortor or cement mortor including pillars etc. and remove debries as directed.

Demolition of cement concrete( unreinforced) in floors n. exc. 15 cm thick below or above ground level and dispose off debris as directed.

Dismantling of Asbestos cement ( corrugated or semi corrugated etc.) sheets in roof covering and shifting to store as directed

M&L hardcore(broken stone) of gauge n exc 63mm,deposited,spread and levelled in layers n exc. 15cm thick,watered and rammed to a true surface.

Dismantling of framed truss span exc. 10m but not exc. 15 m

M&L,shingle(stone bajri) filling in floors,laid in layers nexc. 15cm thick,spread,levelled,and blinded with earth and rammed including watering.

Dismanttling of timber scantling 40sqcm and over in section in framed work.

Dismantling of boardings, any discription , fixed in position with nails.

M&L,Reinforced cement concrete of type, M20,( 20mm graded aggregate) in foundations,footings floors, foundation beams,plinth beams,bases for columns,septic tank etc in pannels .

M&L,Reinforced cement concrete type M20(20mm graded aggregate) in beams,lintels over 1.5m span.

M&L,Brick work with sub class 'B"bricks,straight or curved on plan built in 1:6 cement mortar.

M&L,Form work to sides of concrete foundations,footings,bases of columns,sides and soffits of plinth beams,septic tank etc. for nflat rough finished surface .

M&L,Form work to sides and soffits of roof beams,lintels etc.including for rough finished surfaces.

S&F 2nd class hard wood(sal/sarai) plain,solid,straight chowkats and frames,wrought,framed rebated on the solid,rounded or chamfered,put together with glue pinned at joints.

S&F,2nd class HW ( Bija sal / Kasai)plain,framed panelled shutters (Four nos of panel) of 40mm thick with panels of timber flat on both faces(feather edged) fitted to chowkats.

S&F glazed and skeleton shutters of 2nd class hard wood(Bijasal/Kasai) of 35mm thick open rebated and prepared to receive glass gauge etc.divided into squares,with plain ,chamfered mitred and rebated sash bars ,fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified.

S&F,375mm length brass skelton tower bolt with cast brass plate and staple and rolled or drawn brass bolt.

Brass flush bolt type2 and fixed flush 100mm length.

S&F 300 mm length Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed.

S&F,100mm size butt hinges,cast brass with mild steel hinge pin , bright polished and fixed type B11.

S&F,100mm size butt hinges,extruded brass with steel hinge pin,type C21.

S&F,brass handles,cast type,of size 125mm.

Ditto but 100mm size.

S&F MS flat (50x5mm) for hold fasts including nut bolts and washers fitted, fliet plate , MS wind tie, gugget plate etc to wooden chowkats or frames. Fe290 gr. E165.

M&L,Mild steel TMT bars 10mm dia and over,cut to length,bent to shape required,including cranking,bending spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

Ditto but 6mm to 8mm dia.

M&L,rendering 15mm thick cement plastering of 1:4 cement mortar on fair faces of brick work or concrete surfaces and rendering is to be finished even and smooth (without using extra cement) after taking down cement plaster as directed.

S&F,mild steel rag or lewis bolts,screwed one end with hexagonal or square nuts and washer,the other end enlarged and jagged or lewised exc 15cm and n.exc 30cm long.(Diameter of neck 20mm).

M & L 2nd class clean swan hard wood ,wrought,timber framed and fixed in scantlings, truss, purlin and other roof members.

Cutting holes in brick walls (Superficial area exc. 150sq.cm but n.exc.400sq.cm) built in cement mortar .

S&Fpre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws.

S&F,pre painted galvalume aluminium zinc coating GI based plain sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering / cladding to wall, fixed with self tapping screws.

M & L two coat black bituminous paint in wood or steel surface of any discription n. exc. 10cm in girth or width

M&L,Plain fillets of 2nd class soft wood bull nosed,splayed or chamfered. in sections(sectional area exc 3 and n exc 6 sq.cm) secured with nails.

M&L, rough cast wired glass( n exc 0.5 sqm) 6.4mm thick and glazing with wooden beads in square.

S & F of Roof trusses of tubular trusses including special shape washer etc compete as per IS 1161 1979 grade 240 section as required ( Framed) , trussed, purline , tie and fastening and heavy braket freaming quality 'A' including distance pieces, cleat, Gazet plate nut bolts requred for connecting purlin to truss etc. after application of one shop coat of zinc cromate primer paint( including preparation of surface) at contractor's work shop before fabrication.use only.

M&L 3mm thick wall care putty on wall as per IS specification.

M&L,Preparation of new plastered wall surfaces of any description over 10 cm girth or width,not other-wise described and apply two coats of 1st Quality distemper oil emulsion after one coat of primer on plastered and other surfaces with alkali resistant priming paint wall surface.

M&L,Preparation of new plastered ceiling surfaces of any description over 10 cm girth or width,not other-wise described and apply two coats of 1st Quality distemper oil emulsion after one coat of primer on plastered and other surfaces with alkali resistant priming paint wall surface.

M&L,Preparation of old wall surfaces and applying two coats cement paint over a priming coat of cement wash with port land cement slurry to a smooth bodied opaque finish.

M&L,Preparation of new wood and wooden based surfaces of any description over 10 cm girth or width, not otherwise described and apply two coats of 1st Quality synthetic enamel paint after applying pink primet as directed .

M & L, preparing new steel surfaces and painting of steel surface of any description , over 10cm in width or girth , not otherwise described with two coat of synthetic emultion ( ordinary tint Ist quality ) as directed.

Removing of building material etc. to a distance of 1.5 km including loading, unloading and staking at the destination as directed

Credit to dismantled roof ACC/ steel sheets of any thickness .

S & F Flame Proof, Weather Proof Rotary action switch LM-6 type enclosure with threaded or socket head cover with rotary knob operated complete with and including double entries single pole capacity 16 A 250 Volt. Complete all as specified & directed. Note: Should be certified By CIMFR Dhanbad. MAKE: Sudhir / Baliga/FCG/Shyaam/Pluto or equivalent.

S & F of FLP Switch socket & Plug combined in LM 6 cable termination box 25 Amp. 250 Volts. 2P+ earth. Complete all as specified & directed. should be certified By CIMFR Dhanbad. MAKE: Sudhir / Baliga/FCG/Shyaam/Pluto or equivalent

Supply and fixing LED light fitting 2x16/2x20 Watt flame proof, CIMFR Dhanbad certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2, as per IS/IEC 60079- 1 (2007) and IP 65 protection with die cast aluminum hosing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size. Make : Sudhir/Baliga/Shyaam/CG/Pluto or equivalent for FLP enclosure and Osram/Phillips/Havells/CG/Bajaj/Wipro or equivalent for LED.

S & F LED light fitting 1x9W/1X10W, Industrial bulkhead luminaires including LED light IP 65 protection with die cast aluminum hosing with heat resistant toughened glass with LED light fixtures driver, holders, connector etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size. Make : Osram/Phillips/Havells/CG/Bajaj/Wipro or equivalent.

Taking down carefully existing Cu/ Al point wiring (light,Fan,socket,or power ) complete fixture & fittings such as switches ceiling roses,pendents,regulators,sockets, light fittings etc removing material to store for keeping safe custody and making good disturbed surfaces of walls floors etc.

Cross arm, bracings, supports,clamps and back plates fabricated from structural steel section including nuts & bolts, washers,welding,bending, cold or hot, drilling holes for bolts in any shape or size as indicated or directed & inclusive of one primer coat, one under coat & one finishing coat of paint with M & L complete all as specified & directed. Note: Iron angle size (35x35x5 mm) for fixing of fitting on wall. Complete all as specified & directed.

S&F Aluminium strip 25 x 3.15mm with insulated separetors of thickness not less than 2 cm at distance not more than every 40 cm, saddles and fixing screws etc. for roof conductors and down conductors above ground with material and labour.

S&F Distribution board Double Door TPN as per IS 8623, 8(8+24) ways, IP-54 protection, cosisting of following incoming & outgoing with cable end box with all connection with copper lugs. Incoming - 4 pole ISI marked RCBOs for earth leakage, overload & short circuit protection 415 Volt 63 -100 A, (Sensivity 100mA) - 1 nos. Out going- SP MCB(Isolator) 5-40A - 24Nos. Make: Legrand/SSK/HPL/Havells/Standard/C&S/Polycab or equivalent.

Excavating in trenches not exceeding 0.50 m wide and 0.75 m depth s and getting it out in soft/loose soil for laying of U/G cable. Complete all as specified & directed. Note: Digging by JCBs are not allowed.

Sand cushioning in cable trenches 15 cm thick including material & labour.

Supplying & laying unreinforced precast concrete cable cover class LV type 2 with Flat size 300mmx180mmx40mm with identification of cable cover with material & labour.

Returning filling in, including spreading,levelling,watering and well ramming in layers not exceeding 25 cm.

GI pipe medium grade 80mm dia with all fittings and fixed completely to poles & laid in trenches with material & labour.

Demolition & dismantling Cement concrete in ground floors & pavings not exceeding 15 cm thick below or above ground level.

M&L PCC Type B2, mixed by volume 1:2:4 with 40 mm normal size graded coarse aggregate.

Supply & laying XLPE insulated armoured Heavy Duty , electric cable with aluminium conductor, 1100 Volt grade cross- sectional area 70 sq.mm 3 1/2 core without joint including termination of both the ends with proper lugs with M & L. Complete all as specified & directed. Make of Cable : Fort Gloster/CCI/Havells/Finolex/Zenium/Polycab or equivalent.

Supply & laying XLPE insulated armoured Heavy Duty , electric cable with aluminium conductor, 1100 Volt grade cross- sectional area 150 sq.mm 3 1/2 core without joint including termination of both the ends with proper lugs with M & L. Complete all as specified & directed. Make of Cable : Fort Gloster/CCI/Havells/Finolex/Zenium/Polycab or equivalent.

S & F Switch fuse unit 100 Amp, 415 Volt, 3 Phase, with sheet steel enclosure, complete with neutral link of capacity 100 Amps. Make: English Electric/ SSK /C&S/Standard /Havell's or equivalent.

S & F Switch fuse unit 200 Amp, 415 Volt, 3 Phase, with sheet steel enclosure, complete with neutral link of capacity 200 Amps. Make: English Electric/ SSK /C&S/Standard /Havell's or equivalent.

Supply and fix cable jointing/termination kit for 1.1KV grade cable for straight through joint/termination complete with jointing material heat Shrink type and accessories suitable for 31/2 / 4 core XLPE, armoured, Al conductor cable of size 70 to 95 sq. mm indoor/outdoor type. Make: M seal/Raychem/Cabseal or equivalent.

Supply and fix cable jointing/termination kit for 1.1KV grade cable for straight through joint/termination complete with jointing material heat Shrink type and accessories suitable for 31/2 / 4 core XLPE, armoured, Al conductor cable of size 120 to 150 sq. mm indoor/outdoor type. Make: M seal/Raychem/Cabseal or equivalent.

M&L for Flame proof point wiring (One light /Fan/Exhaust fan point controlled by one switch) with 1100 volts grade PVC insulated sheathed, single core 1.5 sq.mm nominal area stranded copper wire drawn into and including surface rigid steel stove enamelled conduit (ERW) of suitable size but not less than 19 mm dia, 16 gauge with and including flame proof fitting such as bends, elbows, coupling and other accessories(duly approved by CIMFR Dhanbad) and as per IS fixed with spacers, saddles, screws etc. with 14 SWG continuous galvanized earth wire, mounting of switches on wall for sockets, fan regulators etc., max 4 point in each circuit complete all as specified and directed. Make of FLP accessories: Sudhir/Baliga/FCG/Shyaam/ pluto or its equivalent. Make of wire: Havells/Finolex/Polycab/sterlite or equivalent.

……..Ditto……….. as above but with 2.5 sqmm copper wire for One 3 pin socket out let 16 A point independent.

S & F Junction Box LM-6 type flame proof and weather proof suitable for explosive atmosphere flanged, cover with gasket size 100x6mm with and including connector bock, duly wired up (approved by CIMFR Dhanbad) suitable for 19mm steel conduit upto 4 way complete with spigotted cover and a dome cover having on the top. Complete all as specified & directed. MAKE: Sudhir / Baliga/FCG/Shyaam/Pluto or equivalent.

S&F flame proof flexible conduit 450mm with FLP gland for connection to FLP tube light fittings. Complete all as specified & directed. MAKE: Sudhir / Baliga/FCG/Shyaam/Pluto or equivalent.

S & F Distribution board factory fabricated made out of 2mm thick MS sheet with hinged cover & locking arrangement, outdoor type weather and vermin proof suitably ventilated duly powder coated with postman RED color painted & metal enameled RED & WHITE painted Danger board riveted etc suitable for housing incomming/outgoing cable/main switch/DB's etc (Min Approx size 600x450x300mm) complete with and including necessary fixing distribution box on wall complete all as specified and directed. Note:- For accommodation of complete MCB DB.

Supply and fixing of single pointed rod ( Al solid rod ) 20mm dia and 600mm long fixed with angle iron size 50mm X 50mmX 6mm thick, 1.5 meter long including binding with galvanized steel two strand barbed wire of 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and surrounded to the above angle with proper clamping both the end protection from the monkey nuisance. Complete bracket to be fixed on the wall of the building or existing truss/girder of the building with proper grouting bolts of nut bolts of 12mm dia with material Labour.

S & F of Earth pit marker of cast iron size 150mmx100mmx3mm thick embosing as "LP/ST/PE EARTH PIT" with nut & bolt , MS angle iron size 40mmx40mmx5mm length 1700mm buried 500mm near earth pit chamber into ground with cement concrete (1:3:6) size 200mm x 200mm x 300mm duly painted with all respect with M & L.

Earthing complete (including excavation of soil) with GI plate electrode 600x600x6.0mm thick burried directly in ground (earth plate not less than 2.25m below ground level) with top edge of the plate not less than 1.5m below normal ground level and duly filled with alternate layer of char coal & salt from 150mm below the plate to 150mm above the plate (total 900mm thick) connected to GI earth strip size 25x4mm in GI protection pipe of size 40mm dia upto 7.5m long by means of nuts, bolts, washers, check nuts of GI steel, fitted with funnel complete all as per procedure and as shown in SSR electrical plate No. 3 connected to earth test point/earth bus (to be provided near incoming mains) all as specified and testing including RCC earth pit chamber duly cement plaster finished and RCC pit cover 1mX1mX150mm, PCC hard standing surrounding the earth pit chamber, location of the earth pit marked on the nearest wall to be written with paint (for distance & value of earth pit) with material and labour. Earth pit chamber will be made 0.5m above the ground level.

R K SETHI (BID ID -755581)

SHRI KRISHNA CONSTRUCTION (BID ID -744364)