SPL REPAIR REPLACEMENT OF LT OH LINE CONVERTED TO UG CABLE AND PROVN OF DRAINAGE LINE WITH RETAINING WALL ALONGSIDE CONNECTING RAMP AT PALAMPUR MIL STN

Amount

Dismantling and ACSR & AAC onductor from LT pole any type and size complete all specified and directed.

Dismantling and removal of Stay Assy /stay wire complete all specified and directed

Dismantling of insulators any type, any size complete all as specified

Dismantling U/S any size of cross arms from pole /structures and fencing post,struts etc. complete all as specified and directed.

Excavation in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for foundation, shafts, man holes,for under ground cable / erection of poles, stays etc not exceeding 10 Square metre on plan and getting out in soft and loose soil including dressing/trimming of sides and leveling, grading and ramming of bottom of excavation complete all as specified and as directed

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in any type of soil complete all as specified & directed.

Removing excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified & directed.

M&L sand cushioning to under ground cables 8 cm thick before laying the cable and 15 cm, thick after laying, stretching and testing the cable complete all as specified and directed by Engr-in-Charge.

M&L laying in trenches burnt brick sub class 'B' for cable protection laid adjacent to each other length wise perpendicular to the central axis of cable complete all as specified.

Supply & laying of UG cable XLPE insulated armoured heavy duty elect cable with stranded aluminium conductor 1100 volts grade cross section area 70 Sqmm 3.5 core laid in trenches/ fixing on panels/walls/poles or passing through pipe including connecting with suitable lugs, glands, nuts and bolts and testing complete all as specified and directed. Make: Havells/CCI/Gloster (Note: (i) Cable joint shall be measured and paid separately.)

All as per item No. 10 above but of cross sectional area 50 Sqmm, 3.5 core.

All as per item No. 10 above but of cross sectional area 35 Sqmm, 3.5 core.

All as per item No. 10 above but of cross sectional area 10 Sqmm, 4 core.

Supply, install, testing & commissioning of CPRI approved LT panel board, outdoor type, floor mounted, factory made suitable for 415 volt, 3 PH, 4 wire , 50 Hz , AC supply system having busbar chamber with Aluminium bus bars duly insulated by insulation of RYB colour 200 Amps rating mounted on porcelain insulators. The panel shall be factory made, double door, made out of 3.15 mm thick MS Sheet (CRCA) totally enclosed dust, vermin & rust proof front operated, front & rear opening with locking arrangement fixed with MS angle iron frame of sie 40X40X6 mm and duly painted with two coats of synthetic enamel paint over a coat of red oxide primer with colour as directed including internal wiring with multistranded copper conductor cable of suitable size incl lugs and cable gland to incoming and outgoing cable etc all as directed at site and comprising of the following:- (a) MCCB 250 A, 4P, 415 Volts AC supply , thermal magnetic release type 36 KA-01 No (b) MCCB 125A, 4P, 415 Volt 25 KA thermal magnetic relase type -01 Nos. ( c) MCCB 63A, 4P, 415 Volt 25 KA thermal magnetic relase type -03 Nos. (d) Timelite -110 A 3 Pole, 230 V Digital time switch Make : indoasian 01 Nos (e ) On load change over switch 250Amp inbuilt with panel -01 Nos (f) Panel mounted multi function meter for measuring Voltage (0-500 Volts), Current (0- 100 Amps) and frequency-01 No (g) RYB neon indicating lamp panel mounting type (Set of three ) - 01 No (h) Internal wiring of the panel board with single core copper cable PVC insulated of suitable size and control fuses (j) Cable entry gland and two no earthing terminal

Supply,install,testing and commissioning of CPRI approved factory made LT feeder piller box outdoor type with double doors provided with locking arrangements dust, vermin and water proof made out of 3.15 mm thick CRCA sheet duly compartmentalized inside panel with 2mm thick CRCA sheet powder coated with back door detachable fixed with nuts, bolts and washers and front doors openable type fitted with hinges and knobs/locks. Panel is to be placed on angle (size 50x50x6mm) frame duly painted with two coats of synthetic enamel paint over a coat of primer to the portion visible to eye supported on 04 legs 750mm long each duly 450 mm grouted in PCC blocks of type 1:2:4 type B-1and 300mm above ground level for entry of cables suitable for 3-phase, 4-wire, 50Hz,415 volts,with and including necessary incoming and out going cable connection with proper size aluminium lugs, nut bolts etc including the folowing complete all as specified and as directed:- (a) MCCB 400 Amp,4P, 36KA (I/C for Main Supply) - 01 Nos (b) MCCB, 100A, 25 KA, 4 Pole (OG) 03Nos (c) MCCB, 63A, 25 KA, 3 Pole 02Nos (d) MCB, SPN 32A, 25 KA, - 01No (e) LED type AC 220V Phase Indicators RYB, Make : C&S/Schnieder/BCH - 02 Set (f ) Aluminium strip bus bars with heat shrinkable type colour code PVC insulation sleeves 600 Amps capacity TPN mounted on epoxy insulators - 02Set Voltmeter, Amper meter,indicator lamps , CT coi 100/5-01 set. (v) Aluminium Bus bar 4 strip -600 Amps capacity. (vi)Internal wiring of panel board with copper cable single core of sutable size and incl 03 Nos bakelite control fuses. [g] Danger notice plate for LT with conventional skull and bones duly rivetted/pasted to the panel board door Note :- The contractor will approved the panel drawing before incorporate in the work and should be CPRI approved

Material and Labour earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of plate not less than 1.5 metre below ground level, connecting to galvanised iron strip 32X6 mm size (as earth lead strip), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 40 mm bore including provn of concrete pit in plain cement concrete M-15 type B-1 using 20mm graded crushed stone aggregates with 40mm thick cover of rainforced cement concrete M-15 reinforced with XPM (weight not less than 4 kg/Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electrical plate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion including taking down the U/S earthing.

All as per item No 16 above here in before but using 4 mm GI wire complete

Supply and fix cable jointing kit for 1.1 KV grade cable for straight through joint complete with Jointing material (Epoxy Based) and accessories suitable for 3½/ 4 core XLPE armoured Al conductor cable of size 25 to 50 sq mm complete all as specified and as directed.Make : Denson/M-seal

Supply and fix cable jointing kit for 1.1 KV grade cable for straight through joint complete with Jointing material (Epoxy Based) and accessories suitable for 3½/ 4 core XLPE armoured Al conductor cable of size 70 to 150 sq mm complete all as specified and as directed.Make : Denson/M-seal

M&L laying GI Tubing light grade 80mm dia for cable potection in road/floor complete all as specified .

M&L laying GI Tubing light grade 50mm dia for cable potection in road/floor complete all as specified.

M&L laying GI Tubing light grade 40mm dia for cable potection in road/floor complete all as specified .

Supply , fixing, testing and commissioning of factory made LT panel board made out of CRCA sheet 3.15mm thick outdoor type totally enclosed with front opening hinged doors with canopy sloped top projected and floor mounted , weather and water proof as per IS-8623 with necessary locking arrangement all as specified and directed including painting with two coats of synthetic enamel paint over a coat of red oxide primer , internal electric connections as required suitable to accommodate the following :- (i) MCCB 100 Amp TPN -01 No( I/C), (ii) MCCB 63A -02 Nos (O/G) , Al bus bar 400Amp indication lamps -03 Nos complete all as specified and directed

M&L Plain Cement Concrete 1:2:4 type B-1 using 20mm graded stone aggregate for coping around poles,earth pit ,including provision of necessary form work, finishing even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge.

M & L Plain Cement Concrete 1:3:6 type C2 using 40mm graded stone aggregate as in road cutting filling, foundation, fencing post , struts etc. complete all as specified and directed by Engr - in Charge.

Supply and fixing in replacement of MCCB 200 Amp rating,4-pole 415V, 50 Hz breaking capacity 25 KA, Adjustable & fixed magnetic setting type.

Supply and fixing in replacement of MCCB 160 Amp rating,4-pole 415V, 50 Hz breaking capacity 25 KA, Adjustable & fixed magnetic setting type.

Supply and fixing in replacement of MCCB 125 Amp rating,4-pole 415V, 50 Hz breaking capacity 16 KA, Adjustable & fixed magnetic setting type.

Supply and fixing in replacement of MCCB 100Amp rating,4-pole 415V, breaking capacity 16KA. Make, Havells/C&S/Schneider

M&L PVC copper wire of size 1.5 Sqmm incliding PVC conduit with clamp for connetion to security light fitting complete all as specified and directed

M&L HDPE Double Wall Corrugated pipe of size 90mm outer dia and 75mm inner dia confirming to IS:14930 Part-II including necessary pipe fittings such as couplers, end caps, bend etc. including fixed to wall/roof /pole/trench as required with suitable clamps for cable protection complete all as specified and directed.

M&L HDPE Double Wall Corrugated pipe of size 65mm outer dia and 50mm inner dia confirming to IS:14930 Part-II including necessary pipe fittings such as couplers, end caps, bend etc. including fixed to wall/roof /pole/trench as required with suitable clamps for cable protection complete all as specified and directed.

M&L work as in cross arms, support, bracings, stiffeners, clamps channels fabricated from structural steel including nuts, bolts and washers welding, bending cold or hot drilling holes for bolts in any shape or size all as directed including two coats of aluminium paint over a coating of red oxide primer all as directed by Engr-In-Charge.

Supplying and fixing of Off-load type Changeover switch 400 Amp, 4-pole, 415 volt, with enclosure type complete all as specified and as directed.

S&F in repairs cable junction box made of thermoplastic, halogen free, weather proof with metric Knock outs for cable entry including four/five pole terminals and cable entry glands for incomming, out going and connection cable with protection grade IP-66/67 of size 205x255x112 mm and suitable for LT under ground cable any size/capacity including bracing clamp,bolts,nuts & washers. (Make Hensel/ Sintex or equivalent as approved)

S&F Busbar chamber alongwith MCCB 250 Amp including bus bar 400Amp complete with all accessories as specified and directed by Engr in charge

S&F Busbar chamber alongwith MCCB 400 Amp including 400 Amp bus barcomplete with all accessories as specified and directed by Engr in charge

M&L stay assembly complete with accessories as shown in electrical plate No. 1 (loop type insulator, stay clamps, excavation and concrete measured separately)

M&L boring of holes under road, pavement, hard standing by trenchless technology using ultra sounding technique and necessary machine including HDPE pipe of 100 mm dia suitable for 0.4 mpa working pressure all as specified and directed by Engr in charge.

S&F Astronomical time switch 100A , TPN copper busbar, with 4 outgoing complete as specified and direced by Engr in charge

M&L PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L brick work with sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in Cement mortar 1:6, complete all as specified and directed.

M&L plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate cast in situ in lintels up to 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, water through and the like including weathering, slightly rounded or chamfered angles and throating including use of form work (straight or curved) complete all as specified & directed.

M&L rendering 15mm thick plaster in CM 1:4 on fair faces of brick/concrete surfaces and finished the surface even and smooth without using extra cement with WPC @ 3% by Wt. of cement (external surfaces) complete all as specified and directed. Note: WPC shall be measured and paid separately.

S&F rolled mild steel sections like angle, channel, flat etc as inframed work such as grills, gratings,etc,with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars; barred iron doors; ladders ; framed balusters; walk ways; railings; framed work of water tanks and similar work confirming toFe-290Gde E-165 complete all as specified & directed by Engineer-in-charge.

Demolition of stone slabs and tiles of any description of thickness in floors, aprons etc complete all as specified and directed.

M&L 75mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in sub base etc, finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L laying coloured tiles of size 400x400x12mm laid in floors or wall over 15mm screed bed in CM 1:4 with grey cement and pigment any shape and size complete all as specified and directed.

S&F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L pre-cast cement concrete type B-1 1:2:4 (20mm graded crushed stone aggregate) as in landings, cover slabs for man holes,chullah hoods,chajjas,water troughs,mangers,shelves and similar articles with plain faces, set in CM 1:4 complete all as specified and directed.

M/s Sheetal Associates (BID ID -3402427)

M/S SAI CONSTRUCTION (BID ID -3406778)