SPECIAL REPAIR TO BLDG No. S-18 (OR Living) of 285 MED REGT AND CERTAIN REV WORK AND MINOR WORK AT MASIMPUR MIL STATION

B & R Division Items

Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified and directed.

Demolition of Concrete of any description and in any position not otherwise specifically provided complete all as specified and directed.

Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and as directed.

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles to stores and rubbish off the premises.

Dismantling stone slabs and tiles of any description or thickness in floors, apron etc including cement mortar bedding (but not backing) and disposing off complete all as specified and as directed.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings all as specified.

Dismantling mild steel work or wrought iron of any description and in any position complete all as specified and as directed.

Dismantling boarding any description fixed in any position with nails all as specified.

Dismantling wall and ceiling boards (AC, fibre, pulb, insulation etc) or insulation boards slabs/blankets any thickness including cover fillets all as specified and as directed.

Dismantling of timber scantling 40 Sqcm and over in section, in any position in unframed work.

Dismantling of rain water/sewage pipe of any type and any size including fitting complete all as specified and as directed.

Taking down cement plaster on brick or stone walls etc, including raking out joints, hacking for key scrubing down with water etc complete all as specified and as directed.

Taking down chokhats or frame with shutters (without taking off shutters from frame) each not exceeding 1.50 Sqm each complete all as specified.

Taking down Chowkats or frames with shutters exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutters from the frame) complete all as specified directed.

Taking up or down 15mm dia GI steel tubing and connections, including cleaning for refixing complete all as specified and as directed.

Taking up or down 20mm dia GI steel tubing and connections, including cleaning for refixing complete all as specified and as directed.

Surface dressing n.exc. 15 cm deep and getting out in soft/loose soil complete all as specified.

Excavation over areas not exceeding 1.5 mt deep in soft/loose soil complete all as specified.

Excavation in trenches not exc 1.50 mtr wide & not exc 1.50 mtr deep and getting out in soft/ loose soil complete all as specified.

Returning, filling in trenches including spreading, leveling watering and ramming in layers not exceeding 25cm all as specified.

Removing of surplus soil not exceeding 50 m and deposited where directed at a level not exceeding 1.50m above the starting point all as specified.

Earth filling under floor incl spreading ,levelling & well ramming includuing watering as required n exc . 25 cm thick complete all as specified. (Note :- Earth obtained from Excavation items are reused )

M&L for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified.

M&L for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified.

M&L for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified.

M&L for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified.

M&L for hardcore of broken stone gauge n exc 63mm, deposited, spread and leveled in layer n.exc 15cm thick, watered and rolled / rammed to a true surface all as specified and directed .

Use and waste Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished flat surfaces of concrete complete all as specified and as directed.

Use and waste of Form work to sides of pillars, posts, struts, piers, columns and stanchions for rough finished flat surfaces of concrete all as specified and directed.

Use and waste Formwork to sides and soffits of floor or roof beam, beam hunching, girder, lintels, cantilever, shelves including supports, etc for rough finished flat surfaces of concrete complete all as specified and as directed.

Use and waste Formwork to soffits of suspended slabs such as roof slabs, landings and similar work, not exceeding 200mm thick( Horizontal or Sloping ), for rough finished flat surface of concrete all as specified and as directed.

Use and waste Formwork to edges of concrete flats,slabs etc incl fair finished surfaces exe 5cm but n.exe 10cm wide all as specified nd directed.

Use and waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished flat surfaces of concrete complete all as specified and as directed.

M&L for PCC (1:4:8), D2 using 40 mm graded stone aggregate as in foundations, sub-base,filling and mass concrete complete all as specified and as directed.

Material and labour for 75 mm thick Plain Cement concrete type D2 1:4:8 (40mm graded crushed stone aggregates) for sub base in floor fair and rough for receiving tiles all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in plinth protection finished even and fair without using extra cement laid in alternate panels and joints filled with bituminous 1 part and 3 part of sand complete all as specified and directed.

Material and labour for providing Plain Cement Concrete (1:3:6) type C1 using 20mm graded stone aggregate as in surface channel and drain all as specified and directed.

M & L for providing 75 mm thick cement concrete (1:3:6) type C-2 using (40mm graded stone aggregate) as in Sub base of floor rough surface complete all as specified.

Material and labour for cement concrete 75 mm thick PCC type C2 1:3:6 (40 mm graded aggregate) as in path , plinth protection,finished even and smooth without using extra cement complete all as described.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends for etc complete all as specified and directed.

Add or deduct for each 25 mm girth or part thereof over or under 30cm (For adjustment in girth of item No mentioned Above )

M&L for providing 25 mm thick cement concrete (1:2:4) type B-1 using (20mm graded stone aggregate) as in flooring to receive the topping layers complete all as specified.

Material and labour for cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands,plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating , includiong necessary formworks, complete all as specified and directed.

Material and labour for providing Reinforced Cement Concrete M-25 (Design Mix) using 20 mm graded aggregate as in foundation including rafts, footings, foundation beams, plinth beams, bases for columns etc complete all as specified and directed.

Material and labour for providing Reinforced Cement Concrete M-25 (Design Mix) using 20 mm graded aggregate as in columns, pillars, piers, posts and struts complete all as specified and directed.

Material and labour for providing Reinforced Cement Concrete M-25 (Design Mix) using 20mm aggregate as in slab supported on walls , beams, and column in floors, roof, landing, balconies, canopies, deck slab and in shelves and like etc comlpete all as specified and directed.

Material and labour for providing Reinforced Cement Concrete(M-25 (Design Mix) using 20 mm graded aggregate as in beams, cantilever, lintels over 1.5 m complete all as specified and directed.

Material and labour for providing Reinforced Cement Concrete nominal mix 1:1.5:3 type A1 using 20mm aggregate as in slab supported on walls , beams, and column in floors, roof, landing, balconies, canopies, deck slab and in shelves and like etc comlpete all as specified and directed.

M&L for Brick work with sub-class `B' bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 Complete all as specified and as directed.

M & L for half brick work in cement mortar (1:4) straight or curved on plan to any radius with locally available Subclass ‘B’ old size best quality bricks all as specified.

Material and labour for 10mm dia and over TMT bars, cut to length bend to shape as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

S&F Mild steel bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Material and labour for Mild Steel TMT Bar 5mm dia and over up to 10 mm dia as in stirrups, spacers and binders as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed

M&L rendering 15 mm thick cement plaster in two layer Each of 10+5 mm thick on fair faces of brick wall or concrete surfaces in CM (1:4) & water proofing compound mixed with second layer @ 3% finished fair and even complete all as specified. ( Note -W.P.C. shall be measured and paid separetly).

Material and labour for Rendering/plastering, 15 mm thick (10mm+5mm) in two layers in cement mortar (1:4) on any face of brick walls or concrete surfaces, using WPC@3%, surfaces finished finished even and smooth without using extra cement complete all as specified. (WPC measured separately).

M&L for 10 mm thick rendering in cement mortar (1:6) on fair face of brick or concrete surface finished even and fair all as specified.

Material and labour 10mm thick rendering in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified.

M&L for 10 mm thick rendering in cement mortar (1:3) on Roof slab surface & water proofing compound mixed @ 3% finished fair and even complete all as specified. ( Note -W.P.C. shall be measured and paid separetly)

M&L for 5 mm thick rendering in cement mortar (1:3) of cieling surfaces finished even and smooth complete all as specified.

Supply only water proofing compound all as specified and as directed.

Erection & Fixing only Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates all as directed.

Supply and fix Framed work such as grills, gratings, etc.. with ends of bars or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con-forming to Fe-290.Gde-E-165 complete all as specified and directed.

S & F of mild steel rolled sections (Fe-290, Gde E-165) as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and other misc brackets ; fixed with angle cleats for fixing of eaves board or other connecting plates complete all as specified.

S & F mild steel works as in bands, straps, supports or stays for rainwater, framefor fixing of eaves board, ventilating pipes, including bolts, if required: hooks (stay), hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hanging fans; plain angle cleats for securing purlins to wood trusses or rafters, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

Supply and fix pre-painted galvatume aluminium zinc coating GI based corrugated/semi corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws and rubber washer as specified.

Supply and fix pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws and rubber washer as specified.

S & F Pressed steel frames made of 1.25mm thick MS sheet of profile 105x60mm for door and window frames with one or more rebates including hinges, lock strike plate, shock absorber, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified.

S & F Pressed steel frames made of 1.25mm thick MS sheet of profile 125x60mm for door and window frames with one or more rebates including hinges, lock strike plate, shock absorber, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified.

Material and labour Cement concrete (1:3:6), type C-0 using 12.5mm graded stone aggregate as in filling of pressed steel frame and concrete for fixing of holdfast including necessary form work complete all as specified.

Material and labour for suspended false ceiling using E-grid 2430, 180 GSM (exposed ceiling suspension system) of grid size 600mmx600mm with main runner 38 mm x 24 mm and wall angle 24mm x 24mm using 4mm thick high Pressure Non Asbestos Fiber Cement decorative Board (E-Board Classic) in a grid of GI systtem duly suspended with 4 mm dia GI bar hanger fixed with steel dash fasteners or iron purline from the roof with adjustment clip providing positions for light fixtures, air conditioning diffuser and ducts, sprinkler, smoke detectors etc. The main runners to be secured to structural soffits by hanger @ 1220 mm maximum c/c. The last hanger at the end of each main runner should not be interlocked between main runners @ 610mm c/c, as to form 600 mm x 600 mm grid all as specified and directed. Make : Everest Industries Ltd or equivalent as per IS 14862 all as specified and directed.

M&L Non-skid colour ceramic tiles 7 to 8 mm thick coloured ( square/ rectangular) area of each tiles exc 0.11 Sqm but not exc 0.18 Sqm including screed bed or bedding layers of 15 mm thick cement mortar (1:6) as in floors set and jointed in pointed in white or colour cement complete all as specified and directed .

M&L for Non skid ceramic paver tiles area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm floor set, jointed &pointed with neat cement slurry with white cement and pigment including 20mm thick screed bedding layer in cement mortar (1:6) all as specified and directed.

M&L Non-skid colour ceramic tiles 7 to 8 mm thick joint free coloured ( square/ rectangular) area of each tiles exc 0.18 Sqm but not exc 0.38 Sqm including screed bed or bedding layers of 15 mm thick cement mortar (1:6) as in floors set and jointed in pointed in white or colour cement to match the shade of tile complete all as specified and directed .

M&L Non-skid colour ceramic tiles 7 to 8 mm thick joint free coloured ( square/ rectangular) area of each tiles exc 0.18 Sqm but not exc 0.38 Sqm as in skirting, dados and risers to steps etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 10mm thick backing coat of rendering with CM 1:4 as specified.

M&L for non-skid ceramic tiles, coloured, area of tile exceeding 0.11sqm but not exceeding 0.18sqm each, 7 to 8mm thick of superior quality as in floors, etc. and jointed in neat cement slurry and pointed in white cement (mixed with colouring pigment to match the colour of tiles), laid over and including 15mm thick screed bed in CM 1:4 (rate shall be included) complete all as specified and as directed.

M & L glazed ceramic coloured tiles 450x350x7mm thick as in vertical surfaces such as skirting/dado etc over 10 mm thick cement mortar (1:4) set & jointed in neat cement slurry & pointed in white or coloured cement to match the shade of tile complete complete all as specified and directed.

M&L for 20 mm thick granite (any type) work (table rounded and polished) in steps, jambs pillars, windows-cills cooking plateforms, urinal partitions, stand for WHB and like over 15 mm thick backing coat of cement mortar (1:4) set & jointed in neat cement slurry & pointed in white or coloured cement to match the shade of granite all as specified.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for doors, windows & ventilators any pattern complete with frame including cost of providing and fixing hinges/side lock/rollers for sliding windows and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. Note: Supply of glass panes, wire mesh shall be measured and paid separately and balance fitting fixtures will be deemed included in the unit rate.

S & F 2nd class hard wood, 35 mm thick, plain framed panel shutter (any numbers of panel) with panels of timber flat on both sides (feather edged) or 12 mm thick veneered particle board medium density fitted to chowkats or frames complete all as specified and directed.

S & F 2nd class hard wood glazed and skeleton door shutters 35 mm thick open rebated and prepared to receive glass, guage etc (withoput sash bars), edge of framing plain chemfered ro rounded fitted with cut and mitred beds for securing glass etc size of members of shutter as specified in SSR Part I section 8 clause 8.20(a)

Supply and fix Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.0mm and fixed with stainless steel wire staples complete all as specified.

S&F 3.00 mm thick sheet glass ordinary quality and glazing with oil putting square nexc 0.5 sqm in each pane complete all as specified.

S & F 3 mm thick sheet glass frosted ordinary quality and glazing with oil putting square n. exc 0.5 sqm in each pane complete all as specified and directed.

S & F Steel ventilator with top hung shutter including hinges, steel peg stay, lugs as in hold fast with locking arrangements, complete all as specified.

S&F PVC door frame of size 50mm X 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube complete all as per specification and all as per drawing.

S & F factroy made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails MS frame shall be covered with neat moulded plain colour PVC channel having a PVC sheet strip of 20mm width stuct inside the solvent cement for styleand plain coloured PVC sheet for top rails, lock rails and bottom rails on either side and as gap insert for top rails and bottom rail panelling of plain colour PVC sheet to be fitted in the MS frame welded to the style and rails with suitable PVC sheet beading and jointed together with solvent cement supplying and fixing in the frame at site as per specification and as per drawing.

S&F 100 mm long butt hinges ,extruded aluminium alloy with Stainless steel hinges pin, anodised (ISI marked) fixed with stainless steel screw.

S&F 150 mm long aluminum anodised barrel tower bolts of extruded section .

S&F 125mm long aluminum anodised handles of extruded section .

S&F 300 mm length of Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified.

Supply and fix 150 mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed.

Supply and fix aluminium anodised alloy handles fabricated type 150 mm size of handle complete all as specified & directed.

S&F 100 mm long butt hinges ,extruded aluminium alloy with Stainless steel hinges pin, anodised (ISI marked) fixed with stainless steel screw.

S&F double action spring hinges, mild steel with steel wire spring, stove enamelled, black, size of spring hinge 150mm complete all as specified and as directed.

S&F Door stopper of aluminium alloy body and tongue, anodised with hard drawn steel springs, fixed to door with over all length 150mm with rubber bush complete all as specified and directed.

S&F as in repairs 25 mm dia and 1mm thick MS chromium plated curtain rods with fixing side fancy type brackets end knobs fixed with steel screws etc all as specified and directed .

S & F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 500 Ltr capacity hoisted and fixed in position all as specified in SSR Part I .

Supply & Fixed Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/ 40mm- 690 gms) for 20 mm bore pipe .

Supply & Fixed as in repair Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/ 40mm- 690 gms) for 25 mm bore pipe.

Supply, lay and fix 15 mm bore galvanised iron water tubing medium grade including all fittings and fixed complete to wall and ceiling or laid in floors all as specified and directed

Supply, lay and fix 20 mm bore galvanized iron water tubing medium grade including all fittings and fixed complete to walls and ceiling or laid in floors. all as specified and directed.

Cutting grooves or rebates not exceeding 15 cm girth, and trimming with or without reinforced surfaces complete all as specified and directed.

Supply and fix swivel shower of PTMT (minimum wt 40 grams) any colour for fixing with 15mm bore pipe complete all as specified and as directed.

Supply and fix shower arm of PTMT 195mm long with bend of 45 degree with flange any colour for fixing with 15mm bore pipe complete all as specified and as directed.

Supply and fix as in repair 20 mm bore dia, Gun-metal, gate valves, with iron wheel head, screwed both ends on GI pipes with GI union fixed in existing/ new location including removing old unserviceable ones complete all as specified and directed.

Cutting grooves or rebates not exceeding 15 cm girth, and trimming with or without reinforced surfaces complete all as specified and directed.

Supply and fix in repair vitreous china wash basin, white, under counter, size 565mm X 465mm X 185mm oval shape including waste coupling and excluding taps, waste ,chain and plug and porcelain stopper complete all as specified. (Make: Parryware Catalouge No- C0483 and Equivalent)

Supply & Fixed in repairs Vitreous china wash down water closet pan ( pedestal pattern ) , white with P or S trap incl. seat cover, fixing bolts but excluding flushing cistern and flush pipe complete all as specified and as directed.

Supply and fix in repair vitreous china Squatting pan, 'Orissa' pattern, Size 580 X 440mm ,with integral foot rests (excluding flushing ciestern and flush pipe) complete all as specified & as directed .

Supply and fix in repair Vitreous China urinals, bowl type urinal flat back large size of 37.5cm x 39cm x 59cm white (Hindware CAT No. -60002 or equivalent), with urinal spreader grating and union for discharge pipe (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe)

Supply and fix vitreous china wash down water closet pan pedestal pattern white with P or S trap incl seat cover but excluding fixing bolts flushing cistern and flush pipe complete all as specified & as directed .

Supply and fix vitreous china wash basin, white flat back size 550 x 400 mm, excluding taps, waste chain, plug and porcelain stopper but including brackets, cutting for and pinning in ends of bracket or erecting stand complete all as specified

S & F PVC valve less syphonic action type of capacity 10 ltrs , low level flushing cistern, white with inlet, ball valve float and handle including brackets complete.

S & F in repairs PVC valveless, syphonic action type, low level PVC flushing cistren 10 ltr capacity white with flush pipe &all fitting and flush pipe complete all as specified

S & F Soap Dish chromium Plated complete all as specified & as directed.

S & F PVC connections 15mm dia size with PTMT nuts of length 450mm. complete all as specified

S&F brass chromium plated tubular towel rail 20 mm dia 60 cm long, with fancy type brass chromium plated bracket on both sides and fixed with steel screws and wooden/ rawl plugs as in repairs complete all as specified .

S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified

Supply and fix, as in repairs, 32 mm dia and 800mm long PVC flexible corrugated waste pipe for wash basin/sink complete all as specified and as directed. Make :(Prayag CAT No. 327)

Supply and fix 15 mm bore bib taps,chromium plated, cast copper alloy with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule all as specified.

Supply and fix as in repair, 15 mm bore bib taps fancy type, chromium plated, cast copper alloy with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule all as specified.

Supply and fix 15 mm bore pillar tap, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without letter Hot or Cold with long screwed shanuls and fly nuts, screwed for iron pipe .

S&F as in repairs, 15 mm bore, Pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified.

Supply and fix 15 mm bore stop valve, cast copper alloy, ,screwed down high pressure, with crutch or butterfly handles for 15 mm bore pipe or for unions all as specified.

Supply and fix as in repair 15mm bore stop valve/angle valve, cast copper alloy cromium plated fancy type screwed down high pressure, with crutch or butterfly handle for 15 mm bore pipe or for unions all as specified.

Supply and fix 15 mm bore angle valve, cast copper alloy, ,screwed down high pressure, with crutch or butterfly handles for 15 mm bore pipe or for unions all as specified.

Supply and fix 15mm bore stop valves/angle valve of cast copper alloy, screwed down, high pressure with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) complete all as specified.

Supply & Fixed in repair Brass Chromium Plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified.

Supply and fix 125mm dia CP brass shower rose with swivel joints, any colour including shower arm 15mm dia, 195mm long with bend of 45 degree with flange of CP brass complete all as specified. Make : Parryware of CAT No-T9809A1 or Equivalent

S & F in repair PVC connections 15 mm size with PTMT nuts of length 450 m complete all as specified.

S & F in repair Soap Dish chromium Plated complete all as specified& as directed.

S&F as in repair Corner glass shelf of radius 225mm and railing height 70mm including fixing arrangements complete all as specified and directed.

Supply and fix in repair Towel rail, 20mm dia brass chromium plated, 600mm long with fancy type brass chromium plated brackets on both sides and fixed with steel screws and wooden/rawl plugs as in repair complete all as specified.

S & F as in repair bevelled edge mirror complete all as specified and directed. (Make : Modiguard, Saint Gobain or equivalent)

S&F 110mm dia PVC (SWR) pipes single socketed, in any length, laid in trenches or in floors / fixed to walls complete all as specified.

S&F 75 mm dia PVC (SWR) pipes single socked in any length with rubber joints, in floor or fixed to walls all as specified & directed.

Supply & Fixed in repairs PVC (SWR) bends 110 mm bore any radius. all as specified & directed.

Supply & Fixed in repairs PVC (SWR) bends 75 mm bore any radius. all as specified & directed.

Supply & Fixed in repairs PVC (SWR) junction single , ( single T) 110 mm bore equal or unequal. all as specified & directed.

Supply & Fixed PVC (SWR) vent cowl (110 mm) all as specified & directed.

Supply & Fixed PVC (SWR) vent cowl (75 mm) all as specified & directed.

M & L for 75mm PVC(SWR) floor trap, plain with chromium plated grating incl jointing with solvent all as specified & directed.all as specified & directed.

S & F PVC (SWR) junction single , ( single T) 110 mm bore equal or unequal. all as specified & directed.

M & L for preparation of newly plastered surfaces and applying three coats of white wash on wall complete all as specified and directed.

M & L for preparation of newly plastered surfaces and applying three coats of white wash on Ceiling surfaces complete all as specified and directed.

Material & Labour for preparation of new plastered surface applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed.

Material & Labour for preparation of new plastered surface applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm.

Material and labour preparation of new plastered surface of walls and applying two coat of oil emulsion distemper over one coat of primer on wall complete all as specified.

M & L for providing and applying wall care putty 1 mm thick in two layers over plastered surface to prepare the surface even and smooth all as specified & directed.

Material and labour preparation of new steel surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed.

Material and labour preparation of old steel surface of any description over 10 cm width or grith and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed.

Material and labour for preparation of new wooden surfaces of any description not other wise described over 10 cm width or girth and applying two coat of Synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M & L applying one coat of cold bituminous primer (as approved by GE) @ 0.25 ltr/ Sqm over dried up surface of concrete / plastered including cleaning surface confirming to IS 3384-1986 complete all as specified.

Supply & laying 3 mm thick(minimum) APP based polymeric membrane weighing not less than 3.0 kg/Sqm reinforced with polyester non woven fabric (weighing not less than160 gms/sqm) with minimum 100 mm transverse laps and 75 mm longitudinal lap over RCC and application shall be according to manufactures's instructions over cold solvent Bituminious primer @ 0.25 ltr/Sqm. Application of polymeric membrane shall be by torching etc as per manufacturer's instruction and complete all as directed

E & M Division Items

Taking down carefully copper/aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc including removing from site for taking credit and making good to disturbed surface of walls, floors etc as per existing specification complete all as specified and as directed.

Taking down carefully submain wiring including all accessories without disturbing existing wiring fittings fixtures etc and making good to the disturbed surfaces all as directed and as specified in any type and size all as directed.

Dismantling old unserviceable main switches, sheet metal enclosures DB including MCBs etc and removing from site for taking credit incl making good to disturbed surface of wall as per existing specification complete all as specified and as directed.

Taking out old U/s XLPE cable of any size/type taking out of olf bricks/cable cover complete all as specified and directed. (Excavation and earth work will be measured and paid separately under respective items)

Dismantling of U/s GI pipe of size 40 mm bore complete all as specified and directed.

M&L for point wiring with FRLS stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, PVC casing caping including all accessories etc ISI marked, with PVC surface boxes suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One light point controlled by one switch.

M&L for point wiring with FRLS stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, PVC casing caping including all accessories etc ISI marked, with PVC surface boxes suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One fan point/exhaust fan point controlled by one, one way switch 5 Amp.

M&L for point wiring with FRLS stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, PVC casing caping including all accessories etc ISI marked, with PVC surface boxes suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One 3 pin 5 Amp socket outlet point controlled by one switch on the same board.

M&L for point wiring with FRLS stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, PVC casing caping including all accessories etc ISI marked, with PVC surface boxes suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One 3 pin 5 Amp socket outlet point controlled by one switch on independent board.

M&L for point wiring with FRLS stranded copper conductor 2.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, PVC casing caping including all accessories etc ISI marked, with PVC surface boxes suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 2.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for for 3 pin, 15 Amp socket outlet, independent

M&L for point wiring with FRLS stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One light point controlled by one switch.

M&L for point wiring with FRLS stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One fan point/exhaust fan point controlled by one, one way switch 5 Amp.

M&L for point wiring with FRLS stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One 3 pin 5 Amp socket outlet point controlled by one switch on independent board.

M&L for point wiring with FRLS stranded copper conductor 2.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 2.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for 3 pin, 15 Amp socket outlet, independent

S&F switch piano flush type button single pole one way 5 Amps all as specified and directed.

S&F socket outlet 2 in 1, 3 pin 5 Amp flush type all as specified and directed.

S&F switch piano flush type button single pole one way 15 Amps all as specified and directed.

S&F Socket outlet 2 in 1, 3 pin, 5 and 15amp flush type all as specified and directed.

S&F ceiling rose surface bakelite with three terminals all as specified and directed

S&F ceiling fan regulator socketed, step type, flush type heavy duty suitable to work on 230 volts Ac supply complete all as specified.

M&L for submain wiring with two single core 1.5 sqmm PVC insulated unsheathed cable multi-strand copper conductor FRLSH drawn through and including PVC non metallic rigid PVC casing caping with all fittings and fixing accessories on roof, walls, ceiling etc including 1 x 1.0 sqmm PVC insulated unsheathed multi strand copper conductor earth wire FRLS connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar and finishes to match existing complete all as specified and directed. Note: Two run of single core cable, one run earth wire and one run PVC casing caping will be measured as one length.

M&L for submain wiring with two single core 6 sqmm PVC insulated unsheathed cable multi-strand copper conductor FRLSH drawn through and including PVC non metallic rigid PVC casing caping with all fittings and fixing accessories on roof, walls, ceiling etc including 1 x 4 sqmm PVC insulated unsheathed multi strand copper conductor earth wire FRLS connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar and finishes to match existing complete all as specified and directed. Note: Two run of single core cable, one run earth wire and one run PVC casing caping will be measured as one length.

M&L for submain wiring with two single core 6.0 sqmm PVC insulated unsheathed cable multi-strand copper conductor FRLSH drawn through and including PVC non metallic rigid Conduit conceled with all fittings and fixing accessories on roof, walls, ceiling etc including 1 x 4.0 sqmm PVC insulated unsheathed multi strand copper conductor earth wire FRLS connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar and finishes to match existing complete all as specified and directed. Note: Two run of single core cable, one run earth wire and one run PVC Conduit will be measured as one length.

S&F wall mounted, compact LED batten 20 watt having 30 mins backup (working as regular 20 watt in normal mode and 4 watt in backup mode) and connecting with three core flexible copper conductor cable of suitable size from ceiling rose including taking down of old unserviceable one complete all as specified and directed. Cat No: LDLL20-BK4-CDL of Crompton or equivalent make of Havells/M/S Jaquar & Company Pvt Ltd.

S&F wall mounted, compact LED batten 20 watt, 220 V, Efficacy: 125 lm/W alluminium housing AC decorative box type with driver and connecting with three core flexible copper conductor cable of suitable size from ceiling rose including taking down of old unserviceable one complete all as specified and directed. Make - Crompton or equivalent make of Havells/M/S Jaquar & Company Pvt Ltd.

S&F bldg security light, LED luminaire 25 watt IP 66 LED lamp, driver etc with all accessories complete all as specified and directed. Cat No. TRP-415-25-57-SL-LM-NBK of Crompton or equivalent make of Havells/M/S Jaquar & Company Pvt Ltd.

S&F bldg security light, LED luminaire 20 watt IP 66 LED lamp, driver etc with all accessories and service Bracket with clamps complete all as specified and directed. Cat No. LSTS-25-CDL/NL-M of Crompton or equivalent make of Havells/M/S Jaquar & Company Pvt Ltd.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp of suitable size complete all as specified and directed..

S & F Angle bracket 40mm dia for fixing building security light of 40mm dia of 1 mtr long bent to shape 45 degree for fixing of security light including MS clamps of suitable size including nuts, bolts complete all as specified and directed

S&F plastic body exhaust fan 300mm sweep complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding and connecting to ceiling rose with flexible copper cable including making holes on the wall and making good to the disturbed surfaces complete all as specified and as directed.

S & F Steel body exhaust fan 300 mm sweep complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding and connecting to ceiling rose with flexible copper cable including making holes on the wall and making good to the disturbed surfaces including taking down of old UNSV one and depositing to MES store yard complete all as specified and as directed.

S & F BLDC ceiling fan 1200mm sweep complete with blades, down rods and accessories, 230 V, min air delivery 210 CFM with service value 6.00 BEE 5 star rated & provn of ‘S’ type fan hook including including taking down of old UNSV one and depositing to MES storeyard for keeping in safe custody complete all as specified and directed. Make- Crompton,Bajaj,Usha.

S & F sheet metal enclosure powder coated TPN three phase and neutral DB for fixing of MCBs, 4 way double door with bus bar including grouting on the wall by means of screws and rawal plugs and making good disturbed surfaces complete all as specified and directed.

S & F sheet metal enclosure powder coated SP single phase DB for fixing of MCBs, 8 way double door with bus bar including grouting on the wall by means of screws and rawal plugs and making good disturbed surfaces complete all as specified and directed.

S&F sheet metal enclosure powder coated single phase DB for fixing of MCBs, 4 way double door with 200 Amps rated bus bar including grouting on the wall by means of screws and rawal plugs and making good disturbed surfaces complete all as specified and directed.

S & F MCB SPN of capacity 40-63 Amps, 240 V, 10 KA 'C' curve complete all as specified and directed.

S & F MCB TPN of capacity 63 Amps 4 pole, 240 V, 10 KA 'B' curve complete all as specified and directed.

S & F MCB SP of capacity 5-32 Amps, 240 V, 10 KA 'C' curve complete all as specified and directed.

M & L in replacement for earthing with galvanised steel earth plate electrode 600mmX600mmX6mm thick burried directly in ground (earth pit not less than 2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below ground level connected to 4mm dia GI wire protected by 20 mm bore light grade galvanised iron pipe and other end connected to test point as directed including funnel with wire mesh and watering pipe 20 mm bore medium grade galvanised iron pipe with charcoal and common salt in alternaterlayers of 15 cm thickness all around the GI plate electrode with concrete pit in PCC 1:3:6 type C-1 with cast iron frame including cast iron cover 10mm thick hinged to CI frame and 6mm MS rod for handle, necessary excavation and earth wok in hard/dense soil and disposal of spoil to a distance n exc 50 m and necessary testing complete all as shown in electrical plate No 3 of SSR part-I complete all as specified and directed.

Supply, fixing, commissioning & testing of XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, Electric power cable (heavy duty) with aluminium conductors, 1100 volts, grade cross sectional area 25 sqmm 3.5 core laid in trenches/fixed to wall/under road/pipe etc with copper cable glands & copper thimbles complete all as specified and directed.

Excavation in trenches not exceeding 1.50 m wide and n.exc 1.5 m in depth for foundation of poles, cable etc, not exc 10 sqm on plan and getting out in soft/loose soil including taking out brick protection etc complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25cm thick complete all as specified and directed.

Removing of surplus soil to a distance not exceeding 50 meter and deposited where directed at a level not exceeding 1.50 meter above the starting point complete all as specified and directed.

M & L for sand cushioning by spreading in trenches crushed sand by gently by punning down manually as in cable protection all as specified and as directed by Engineer-in-charge.

Supply and laying un-reinforced precast concrete cable cover class LV, type-I, flat size 250 mm x 150 mm x 40 mm laid in trenches all as specified.

M&L PCC 1:3:6 type C2 using 40mm graded crushed stone aggregate with 100mm thick for flooring complete all as specified and directed.

S&F gun metal gate valve 25mm dia, cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe complete all as specified and directed.

M&L for steel water tubing 25mm dia, medium grade galvanised with new fitting laid in trenches or on wall complete all as specified and directed.

Material & labour GI tube light grade 40 mm bore for protection of cable complete all as specified and directed.

M&L for cutting of existing GI pipe line 25mm dia for inserting Tee and reducer etc for taking 25mm dia branch pipe including fittings complete.

Taking out old existing earthing and M & L in replacement for earthing with galvanised steel earth plate electrode 600mmX600mmX6mm thick burried directly in ground (earth pit not less than 2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below ground level connected to 4mm dia GI wire protected by 20 mm bore light grade galvanised iron pipe and other end connected to test point as directed including funnel with wire mesh and watering pipe 20 mm bore medium grade galvanised iron pipe with charcoal and common salt in alternaterlayers of 15 cm thickness all around the GI plate electrode with concrete pit in PCC 1:3:6 type C-1 with cast iron frame including cast iron cover 10mm thick hinged to CI frame and 6mm MS rod for handle, necessary excavation and earth wok in hard/dense soil and disposal of spoil to a distance n exc 50 m and necessary testing complete all as shown in electrical plate No 3 of SSR part-I complete all as specified and directed.

Please Enable Macros to View BoQ information