Construction of Nabapur Market at Mazgaon, Tezpur under CIDF

Amount

EARTHWORK IN EXCAVATION: Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00m below the existing ground level a) In ordinary soil (a) In ordinary soil

Earth/ sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary. (b) With hill sand obtained by truck carriage loading and unloading, and carriage to the site of work.

PLAIN CEMENT CONCRETE WORKS: Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1cement: 4 sand :8 coarse aggregate by volume

Providing and laying 25mm thick damp proof course with cement concrete in prop 1:1.5:3 with graded stone agg. of 10mm down nominal size including providing approved damp proof admixture in proportion as recommended by the manufacturer including curing etc. complete as directed.

REINFORCED CEMENT CONCRETE WORKS: Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) (I) Using Mixer Machine (A) In substructure up to plinth level Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. N) Without using admixture, plasticiser c) M25 grade concrete

(B) In super structure from plinth level up to 1st floor level. ii) Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing ) including preparing the top surface and finishing of nosing. N) Without using admixture, plasticiser c) M25 grade concrete

Extra over item Nos. 2.2.1 (I) (B), above for each subsequent floor or part thereof above the 1st floor level. (B) In super structure from 1st Floor to 2nd Floor. ii) Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing ) including preparing the top surface and finishing of nosing. N) Without using admixture, plasticiser c) M25 grade concrete

(B) In super structure from 2nd Floor to 3rd Floor.

(B) In super structure from 3rd Floor to Roof Floor.

(B) In super structure from Roof Floor to Mumty Level.

TIMBER SHUTTERING (FORMWORK): Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc. (b) Using 25mm thick plank

Sides of tie beams, grade beams etc. at or below ground level. (b) Using 25mm thick plank

PLYBOARD SHUTTERING (FORMWORK): Plinth level to 1st floor level Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in: Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face

Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. (a) For depth not exceeding 1.0M.

Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. (a) Floors etc. upto 200mm in thickness.

Staircase with sloping or stepped soffits including risers and stringers but excluding Landing.

Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in: Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face

Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. (a) For depth not exceeding 1.0M.

Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. (a) Floors etc. upto 200mm in thickness.

Staircase with sloping or stepped soffits including risers and stringers but excluding Landing.

Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in: Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face

Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. (a) For depth not exceeding 1.0M.

Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. (a) Floors etc. upto 200mm in thickness.

Staircase with sloping or stepped soffits including risers and stringers but excluding Landing.

Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in: Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face

Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. (a) For depth not exceeding 1.0M.

Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. (a) Floors etc. upto 200mm in thickness.

Staircase with sloping or stepped soffits including risers and stringers but excluding Landing.

Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in: Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face

Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties.(a) For depth not exceeding 1.0M.

Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. (a) Floors etc. upto 200mm in thickness.

MASONARY WORK : Providing soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. (a).Brick on flat soiling

100mm thick wall using Cellular Light Weight concrete block of Size 500x200x100mm conforming to IS-2185 Pt-3 or pt-4 in cement mortar of proportion 1: 5 including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding rod is to be provided at every 3 course interval and will be measured and paid separately)

Extra for CC block walling on item no 4.3.5 for each subsequent floor or part thereof above the 1st floor level. 1st Floor to 2nd Floor.

2nd Floor to 3rd Floor.

3rd Floor to Roof Floor.

Roof floor level to Mumty level

FLOORING AND FLOOR FINISH: Cement concrete works in topping 1:1:2 (1cement :1sand :2 graded aggregates on R.C.C floor, tread and rise of steps finished with a floating coat of neat cement using cement slurry for bond @ 2.75 kg.of cement per sq. m. of floor to be laid in panels including curing complete as directed. (a) 15 mm thick

CERAMIC TILES: A) ON FLOOR Providing Ceramic Tiles of approved quality, size, shape and thickness not less than 8 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with fix-A Tile Choksey/ Sika/ Pedelite/ Rouf/ White cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed (coloured pigment should be in conformity with colour of slab and as approved and directed by the Department). b)Executive range Somany/ Orient/Nitco/Asian Make ii) Of size 400x400 mm and above

B) ON WALLS: Providing polished ceramic wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (Walls means both interior and exterior walls). b) Executive range Somany/ Orient/Nitco/Asian Make ii) Of size 250mmx350mm and above

VITRIFIED TILES: A) ON FLOOR Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) a) Normal range Somany/ Orient/Nitco /Varmora/VITA/ Marbito/ Make ii) Of size 600mmx600mm and above

GRANITE FLOORING: Providing 18mm thick Granite slab on vertical face of pedestal laid over 10 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete as directed with approved quality of shade.

CEMENT PLASTERING: 15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A) On rough side c) In cement mortar 1:5

B) On fair side c) In cement mortar 1:5

celling and soffits of stairs up to 1st floor level B) On fair side c) In cement mortar 1:5

15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A) On rough side c) In cement mortar 1:5

B) On fair side c) In cement mortar 1:5

celling and soffits of stairs up to 1st floor level B) On fair side c) In cement mortar 1:5

2nd Floor to 3rd Floor.: 15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A) On rough side c) In cement mortar 1:5

B) On fair side c) In cement mortar 1:5

B) On fair side c) In cement mortar 1:5

15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A) On rough side c) In cement mortar 1:5

B) On fair side c) In cement mortar 1:5

celling and soffits of stairs up to 1st floor level B) On fair side c) In cement mortar 1:5

15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A) On rough side c) In cement mortar 1:5

B) On fair side c) In cement mortar 1:5

celling and soffits of stairs up to 1st floor level B) On fair side c) In cement mortar 1:5

CHOWKATHS: Providing wood work in frame (chowkaths) of doors, windows, clerestory windows and other similar works wrought, framed and fixed in position in contact with C.C or brick masonry wall including supplying, fitting and fixing with M.S. hold fast (40mmx3mmx250mm) as per design embeded in cement concrete block in proportion 1:2:4 and with two coats of kiricide oiling to the timber faces in contact with C.C and masonry as directed and specified. (a) With sal wood

Providing, fitting and fixing factory made Santro Flush door shutters having core & cross bands fabricated from seasoned 1st class timber, 25mm core battens, 2.5mm to 3.5mm uniformly thick cross bands, styles & rails made from hardwood timber of width not less than 50mm, fixed to the door frames (chowkath) with necessary hinges, screws, bolts etc. as specified and directed at all levels (Door fixtures and fittings to be measured and paid seperately.) (b) 35mm thick

GRILL: Providing, fitting and fixing M.S. grill of required pattern for windows/ clerestory windows/ openingwith M.S. flats at required spacing in frame all round, squre or round M.S. bars with round headed bolts and nuts or screws. I . Plain grill (c) Fixed to Brickwork/P.C.C/R.C.C.

Supplying and installing uPVC- Fixed Windows made out of Lead free green profile having "GREENLINE" mark of BIS standard uPVC multichambered sections of wall thickness 2.4mm with corners fusion welded, fully reinforced with galvanized steel 1.5/2mm including glazing bead , grooving bead, drain cap, fisher screws, packing pieces, necessary stainless steel screws etc. complete as directed. The windows must be installed complete with all kinds of ironmongery including EPDM gaskets, bridging wedges and glass packers and with suitable water draining system. Application of Silicon sealant from inside / outside of dowcorning / GE or equivalent. With 5mm clear glass (a) Fixed window using uPVC sections of size 58mm x 52mm x 2.4mm thick wall for frame and 58mm x 68mm having 2.4mm thick wall for glass sash having reinforcement of 1.5mm thick in both frame & sash. (WINSTA KOMMERLING/ FINESTA/ ENCRAFT)

Applying one self-priming coat of Unicem "Shakti" brand of required shade over freshly plastered wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth as specified and directed by the department.

Finishing wall with two coats of waterproofing cement coatings of Unicem "Shakti" brand of required shade by thinning 1 part of paint with 1 part of water to give an even shade after throughly brooming the surfaces to remove all dirt and remains of loose powdered materials as specified and directed by the department.

Applying priming coat over new wood and wood based surfaces over 100mm in girth/width after and including preparing the surface by throughly cleaning oil, grease, dirt snd other foreign matter , sand papering and knotting. (a). With ready mixed paint , Wood primer (pink)

Painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matter sand papering and stopping. (i).Surfaces over 100mm in width or girth. b). High gloss (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).

DOOR AND WINDOW FITTINGS: Supplying, fitting, fixing brass fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary c.p. brass screws etc. complete.(bright natural matt & satin finished ). a) Sliding door bolts i) 300mm x 16mm

b) Tower bolts iii) 200mm x 10mm

c) Door handles iii) 150mm

STEEL AND IRON WORKS: Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reiforcement bar

1st Floor to 2nd Floor.

2nd Floor to 3rd Floor.

3rd Floor to Roof Floor.

Roof floor level to Mumty level

PILING WORKS: Providing cast in-situ manually driven reinforced cement concrete piles of using required grade of cement concrete of required bore-diameter, bulb diameter, lengths and with reinforcement as per specifications and drawings. Reinforcement to be measured and paid seperately as per item no. 21.4.1 C) UNIFORM PILE f) Pile Dia 500 mm i) Upto 10 M

REINFORCEMENT: Supplying, fitting and fixing in position reinforcement bars conforming to relevent IS code, for reinforced cement concrete works in piles including straightening, cleaning, cutting and bending to proper shapes and length as per specifications and drawings. The rings should be welded with vertical reinforcements as per specified IS codes of practice. (Inclusive of lap length, hook, chair, bend, anchor...etc) (A) TMT bar made of Primary producer (From Primary producer)

Routine test for test loading to 1.5 times the specified safe working load including construction of any test pile cap and dismantling the same after completion of test. (Rate for Safe working Load)

Initial test for test loading to 2 times the specified safe working load including construction of any test pile cap and dismantling the same after completion of test. (Rate for Safe working Load)

Intigrity testing of Pile using Low Strain/Sonic Integrity Test/ Sonic Echo Test method in accordance with IS 14893 including surface preparation of pile top by removing soil, mud, dust & chipping lean concrete lumps etc. and use of computerised equipment and high skill trained personal for conducting the test & submission of results, all complete as per direction of Engineer-in-charge.

(A) Supplying, mixing, laying and applying the following waterproofing systems over Raft slabs, Roof slabs, Terraces etc. including curing complete as specified and directed by the Department at all levels.: (i) 1mm thick single coat of Master Crete M-81 of Choksey Chemicals /Dr. Sealkit Sealcrete (Asian Chemicals)/ mixed with cement in the ratio 1:2 as a prime coat. (ii) 3mm thick Polymer modified mortar - Cement sand mortar (in prop 1:3) mixed with Master Crete M-81/Dr. Sealkit Sealcrete (Asian Chemicals) @ 15% by weight of cement. (iii) 1mm thick coat of Master Crete M-81 /Dr. Sealkit Sealcrete (Asian Chemicals) mixed with cement in the ratio 1:2 as final coat. (B) Using RHEOMIX 131 OF BASF

Pre construction anti - termite treatment at the bottom of foundation pits and walls on either side up to a height of 300mm from bottom of the excavation made for column plinth beam, wall, trenches etc. by applying the emulsion @ 5 (five) litres per square meter of the surface area before starting construction work (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete. a) with aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or euivalent) and water, i.e. 1% solution.

FIRE EXTINGUISHER: Supply, Installation, Fixing of DRY CHEMICAL POWDER Fire Extinguisher confirming to IS: 2171 with ISI mark and CO2 cartridge will be confirming to IS: 4947 with ISI mark, Powder will be confirming to IS: 4308 with ISI Mark (5 KG) BRAND : FIRESTOP / FIREND / FIRE SHIELD

Providing and fixing of wall cladding stones along the walls made of concrete & other recycled materials with high compressive strength around 22.5 N/SQ.MM and abrasion resistent, exterior grade applied with polymer based adhesive with good adhesion strength and fast curing. Chisel stone with dimensions 23.5"X8.5" (LXH), thickness 26 MM and weight 4.09Kg/Sq ft. to be applied with the adhesive applied as a uniform scratch coat first and individual pieces over it. The protective transparent sealer coat to be done overall with the help of a brush in the final stage for a maintainance free cladding altogether. Fixing and cutting of the stones to be done as per the drawings specifications and instructions of the engineer in charge.

CONCEALED CISTERN: Supplying, fiting and fixing concealed cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately) (C) Jaquar Make Concealed Cistern (Cat.No.CIB-WHT-31801011X) with Control Plate (CP) (Cat. No. CIS-CHR-31191510X)

URINAL: Supplying, fiting and fixing automatic flushing cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately) ii) Hindware make a) White Auto Cister 10 litre (Cat. No.C61002)

WASH BASIN: Providing 12mm 100% Acralic Merino Hanex Solid surface counter tops with Wash basin (480x400mm) with jaguar mak CI/MS Brackets C.P Brass chain with Plug

TOILET CUBICLES: BESCO CUBICLE TITAN SS 1980MM Thickness of Compact Laminate : 12 mm Color of HPL Boards: Single Standard Compact Color Size of Cubicle : As per Drgawing (W) x (D) x 1980mm (H) Door Size : 1765mm (H) X 610mm (W) Divider Size: 1775mm (H) Overall Height Of Cubicle : 1980mm (Including bottom Gap of 150mm) Accessories: Standard – Merino Make Stainless Steel - 304 Grade accessories) a) SS “U” Channel b) SS “F” channel c) SS Top Rail d) SS Coat Hook e) SS Privacy Thumb turn c/w Occupancy Indicator f) SS Door Knob g) SS Hinges with Cover h) SS Adjustable Foot - 316 Grade i) Rubber Lining for Groove j) S.S.Screws 304 G & P.V.C Wall Plugs

DIVISION PLATE - Urinal Modesty SS FMRSUMPPNLZZSS00001 URINAL MODESTY SS Thickness of Compact Laminate : 12mm Color of HPL Boards: Single Standard and Plain Compact Color Size of UMP : 500mm (W) X 1200mm (H) Overall Height Of UMP : 1850mm (Including botom Gap of 650mm) Accessories: Standard - Merino Make Stainless Steel - 304 Grade accessories) - SS a) Right Angle Brackets b) S.S.Screws 304 G & P.V.C Wall Plugs SPECIAL NOTE - Warpage Criteria is 3.0 mm/1000mm for MRS panels as per EN standard- 438.

Providing fitting and fixing Decorative Mirror complete as directed and specified. (B) Jaquar Make (a) Double Arm Wall Mounted reversible plain / Magnifying (3X) Pivotal Mirror (Cat. No.ACN-1193N)

Providing fitting and fixing Glass Shelf complete as directed and specified. (iii) Jaquar make (c) Kubix 600mm long (Cat. No.AKB-35771)

Providing, fitting and fixing CP soap tray / soap dish complete as directed and specified. (i) Jaquar Make (d) Kubix (Cat. No.AKB-35731)

Providing, fitting and fixing Liquid soap dispenser and liquid soap container complete as directed and specified. (i) Jaquar Make (c) Kubix with glass bottle (Cat. No.AKB-35735)

TOWEL RAIL,TOWEL RACK & TOWEL RING: Providing, fitting and fixing CP towel rail complete as directed and specified. (a) Jaquar make (vii) Kubix (600mm long) (Cat.No.AKB-35711)

TOILET PAPER HOLDER: Providing, fitting and fixing Chrome Plated TOILET PAPER holder complete as directed and specified. (a) Jaquar make (vi) Kubix toilet roll holder (Cat.No.AKB-35751)

WASTE COUPLING: Providing, fitting and fixing Chrome Plated waste coupling complete as directed and specified. (a) Jaquar Make (i) 32mm (HT/FT) (Cat.No.ALD-705 / 709)

BOTTLE TRAP: Providing, fitting and fixing Chrome Plated bottle trap complete as directed and specified. (a) Jaquar make (i) Bottle trap (with internal partition) 32mm size with 250mm long wall connection pipe (Cat.No. ALD-769)

Supplying fiting and fixing 87.5 degree PVC bend with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

(iv) 75 mm dia.

Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

(iv) 75 mm dia.

Supplying fiting and fixing PVC coupler of (Supreme / Prince)or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 110 mm dia

(iii) 75 mm dia

COWEL: Providing fitting and fixing PVC cowel of ISI make complete as directed and specified. (ii) 110mm dia. PVC cowel of ISI make

Providing fiting & fixing C.I. Grating to the floors complete as directed and specified. (a) 110mm dia

(b) 75mm dia

Providing fitting and fixing 450mm dia. 90mm thick C.I. Man hole cover and frame of 38 Kg. weight complete as directed and specified

Providing fitting and fixing (600x600)mm 90mm thick C.I. Man hole cover and frame of 25 Kg. weight complete as directed and specified

Construction of inspection pit inside measurement 450mm x450mm x450mm flush with 100mm diameter HCI/PVC pipes and cement concrete base in proportion 1:3:6 over flat brick soling, 12cm brick wall in cement mortar in proportion 1:4 finished with 13mm cement plaster in proportion 1:2 in side wall and floor. 450mm x450mm air tight C.I. inspection pit cover and frame complete including supplying of materials, necessary excavation of pit as directed.

Single phase Submersible motor pump set (texmo/ Crompton Greaves/ Aquatic/ CRI/ V-Guar suitable for 100mm bore well and above. 1 HP STAGE 5 to 18 with control panel.

Supplying fitting and fixing including necessary connection as approved by the deptt. Of starter ( Crompton Greaves/ control & Switch Gear/ BCH/ L&T/ Siemens make) of the following type and capacity as specified and directed by the Department.( Crompton Greaves/ control & Switch Gear/ BCH/ L&T/ Siemens make) D.O.L starter ( Crompton Greaves/ control & Switch Gear/ BCH/ L&T/ Siemens make)0.5 to 10 HP, 0.72 to 20A.

(A)) Exposed or in trenches c) 25 mm nominal outer dia pipe

e) 40 mm nominal outer dia pipe

(B) Concealed pipe with cutting chases & making good the walls b) 20 mm nominal outer dia pipe

BIB COCK: Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand directed and specified. (G.I. & C.P pipes will be measured separately) (i)Standard

ANGULAR STOP COCK: Supplying fitting and fixing chrome plated (C.P.) stop-cock of approved brand and size as mentioned below as directed and specified.(G.I. & C.P pipes will be measured and paid separately) (I)Jaquar (ii)15mm dia( Angular stop cock )

PILLAR COCK: Supplying and fitting fixing C.P. pillar cock of 15mm dia of approved brand as specified and directed (II) Jaguar make . (a) Continental

Supplying fitting and fixing Pipes with all necessary fittings in exposed or in trenches including trenching and refilling the same etc complete as directed C) CPVC pipe with CPVC fittings (Using SUPREME/ PRINCE/ SFMC/ FUSION brand pipe) v) 40 mm (OD) diameter

Tube Well: Labour for boring hole for inserting tube well pipes through different soil/ rock media including hire charges of drill pipes, scaffolding, tools and plants as necessary and taking out the same and lowering pipes, fittings complete as directed by the Department. iv) Bore hole of 150mm diameter

WATER TANK: Supplying and placing plastic cylindrical vertical claused top (PCVC) tank of Sintex / Polycon / Patton make over the stagging with manhole cover with locking and cleaning arrangement including providing pads of size as required for inlet and outlet pipes (III)1000 litre capacity (a) Sintex make

SEPTIC TANK: Supplying and placing ferrocement septic tanks of rectangular shape in to pit with manhole cover with cleaning arrangement over single brick flat soling and 75mm 1:3:6 P.C.C. Baffle wall, inlet and outlet etc are provided at suitable points complete as directed. 200 Users

IRON REMOVAL WATER FILTER: Supplying fitting and fixing iron removal filter filling with treated sand, pebbles, manganishdioxide and other required materials of various filtration rate per hour of DOLPHIN make with all necessary fittings such as valve,bib cock,pipe connection etc.with a free maintanance period of six monthhs (A) With Zoloto fittings (I) 1000 liters capacity (a) 4 mm thick Vessel

Wiring for light/ fan/ call bell point with 2x1.5 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable HFFR/ZHFR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system with 2 mm thick 20mm dia rigid low halogen SFT PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including 6 Amp flush type switch/ bell push (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) in GI/ MS switch board (ISI marked) with phenolic laminated sheet cover ,ceiling rose (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) etc. complete Short point up to 3.00 metre. length.

Medium point up to 6.00 metre. Length.

Long point up to 10.00 metre. Length.

Wiring to 5 a pin 6 Amps plug point with 1.5 sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable HFFR/ZHFR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco or Equivalent Make as approved by the Deptt.) in surface/ recessed 2 mm thick rigid low halogen SFT PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system including 5 pin 6 Amps flush type plug socket and 6 Amps F/T switch (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.), GI/ MS switch board (ISI marked) with phenolic laminated sheet cover including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete, when placed elsewhere. Medium point up to 6.00 metre. Length.

Long point up to 10.00 metre. Length.

Wiring for 5 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable HFFR/ZHFR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system including and fixing 5 pin 16 Amps flush type socket outlets and 16 Amps flush type switch ( Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.),GI/ MS switch board (ISI marked) with phenolic laminated sheet cover earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete with 2 mm thick 20 mm. dia. rigid low halogen SFT PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) 2.3.2) Medium point up to 6.00 metre. Length.

Long point up to 10.00 metre. Length.

Extra long point up to 15.00 metre. length.

Extra long point up to 20.00 metre. Length.

Extra long pont upto 25mtr length

Wiring for circuit wiring with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system. With 2 x 1.5 sq. mm. cable in 20 mm dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

With 3 x 1.5 sq. mm. cable in 20 mm dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including earth continuity in surface/ recessed 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit wiring system. With 2 x 2.5 sq. mm. + earth continuity with 1x1.5 sq. mm. in 20 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

With 2 x 4 sq. mm. + earth continuity with 1x2.5 sq. mm. cable in 20 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

With 2 x 6 sq. mm. + earth continuity with 1x 4 sq. mm. cable in 25 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

Supplying with fitting fixing of blank plate single in modular switch system MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE complete as per direction of department.

Supplying including installation of socket outlet 6/16 Amps 3/5 pin combine shuttered complete , MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE including making necessary connection as per direction of department.

Supplying including installation of socket outlet 6 Amps 3 pin universal combine shuttered complete , MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE including making necessary connection as per direction of department.

Supplying with fitting fixing of 16 amp one way modular clip in switch with LED, MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE including making necessary connection as per direction of department.

Supplying with fitting fixing of 6 amp one way modular clip in switch, MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE including making necessary connection as per direction of department.

Supplying including and fixing of following Metal boxes for MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE in surface/ recessed system complete as per direction of department. 3 module type Metal

4-5 module type Metal

6-8 module type Metal

10 module type Metal

12-16 module type Metal

Supplying including fitting fixing of following front plate of suitable colour MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE as per direction of department. 1 Module

3 Module

4 Module

5 Module

6 Module

8 Module

10 module

16 Module

Supplying with fitting and fixing of electronic modular fan speed controller 2 - module type MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE including making necessary connection as per direction of department. 100 watt electronic modular 4 step speed control 2 - module type

Supplying with fitting and fixing of Single Phase Modular Motor Starter switch MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE including making necessary connection as per direction of department. Modular Motor Starter switch Relay Range 16 - 25 Amps in 3 Module

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door IP-43 surface mounting SPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. ABB, Schneider MG, legrand, Hager make) 8 way SPN double door

Supplying with fitting and fixing MCCB income and MCB outgoing sheet steel, phosphatised, powder painted double door IP-43 surface mounting vertical TPN MCB DB incorporated with bas-bar up to 125 A , Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. ABB, Schneider MG, legrand, Hager make) 4 way TPN (4+12) single door

8 way TPN (4+24) single door

Supplying with fitting and fixing single Pole 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. C Series (Schneider MG, legrand, Hager make) 1.Single pole 10KA 240/415V 50Hz MCB 6 to 32A

Supplying with fitting and fixing DP 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. C Series (ABB, Schneider MG, legrand, Hager make) 40A

Supplying with fitting and fixing panel mounting open execution 25KA 415V 50Hz 4P MCCB (Ics=Icu, adjustable Ir setting 0.7) without enclosure) of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. 25 KA 415V 50 Hz 4P MCCB (Schneider, legrand, Siemens, Indo Asian make) 63A

Supplying with fitting and fixing panel mounting open execution 35/36KA 415V 50Hz 4P MCCB (Ics=Icu, adjustable Ir setting 0.7) without enclosure) of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. 35/36 KA 415V 50 Hz 4P MCCB (Schneider, legrand, Siemens make) 250 A

Supply, installation & testing of Copper Plate earth station with 600 mmx600 mmx3 mm copper earth plate with necessary 40 mm dia. G.I. medium duty watering pipe with G.I. Fittings such as Socket, Tee, elbow, nipple and 50 mmx40 mm G.I. reducing socket for funnel including locking arrangement with 300 mmx300 mmx6 mm C.I. hinged cover plate complete with digging of earth pit, construction of brick chamber and plastering of both inner & outer surface of wall as specified and directed by the deptt .

Extra for using salt (5 K and Charcoal (64 K in pipe Earth Station pit to provide low impedance ground in location of high soil resistivity as and when required and specified by the Deptt.

Supplying & laying of 8 SWG Copper. earth from Earth Electrode (below G.L.) to electrical switch gears or electrical machineries including making necessary connection as approved, specified and directed by the deptt.

Supply and laying of following size Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988, LT armoured U.G. cable laid in pucca flooring, road crossing, drain crossing as per site requirement and partially in air to connection as approved by the Depts. the control switch, through medium duty G.I. pipe (Tata/ Nezone make or equivalent as approved by the Deptt) bend and socket including excavation and refilling the trench and making good damage done as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) Core - 3 & 1/2 A2XWY A2XFY 35.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

150.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

185.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

Supplying including fitting fixing of following A.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department [Without regulator]. Standard model 1200 mm Sweep Usha make)/ Standard model 1050 / 1200 mm Sweep Havells make)/ High speed 1200 mm sweep (ORIENT PSPO make)

Supplying including fitting fixing of following A.C. Wall fan in the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department. SDX 12(CROMPTON /ORIENT/Havells/USHA or equivalent make) 0 with metal body metal blade 400 mm sweep

Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department. Domestic Ventil Air DB 300 mm sweep (Havells make)

Supplying with installation testing and commissioning of Hi -- wall 3 STAR rating non ducted split type air conditioner of the following capacity with cordless remote complete with indoor and outdoor unit, copper pipe and electrical connection up to 5 m between the room unit and out door unit as approved by the Deptt.) and as directed by the department. 1 Ton Capacity Voltas make) Model gold 3S

1.5 Ton Capacity Voltas make) Model gold 3S

2 Ton Capacity Voltas make) Model gold 3S

Supplying with fitting and fixing Voltage stabilizer of the following specification complete including making necessary connection as approved, specified and directed by the deptt. (SKYLAND / Vee-Dee / V GUARD / VERTEX/ INDO/ VENUS make) 2.0 KVA Automatic Input 90-280 V Out put 200-240 V

4.0 KVA Automatic Input 90-280 V Out put 200-240 V

5.0 KVA Automatic Input 90-280 V Out put 200-240 V

ILLUMINATION :- Supply and installation at all locations, heights and levels as directed ceiling and wall mounted luminaires inclusive of all accessories,lamps,fixing in ceilings,on slab soffits or wall as required etc. complete as per specification and laid out as per detailed drawing and directions (wiring work to be paid for separately) Sample of all fixtures shall be approved of prrior to installation Supply of following luminaires :- LED recessed downlighters round of Phillips make cat no.DN195B LED 20S 4000PSU WH S2 18/20W

Installlation

Supply LED recessed downlighters round of Phillips make cat no.DN193B LED 12S 6500PSU WH S2 b) 12W

Installlation

LED surface downlighters round of Phillips make cat no.SM250LED 12S 6500PSU WH a) 12W

Installlation

LED downlighters square of Phillips make cat no.RC380B LED 25S 6500 G4 L60 W60 PSU OD a) 25W

Installlation

LED downlighters square of Phillips make cat no.RC365B LED 33 6500 PSU OD WH a) 33W

Installlation

LED batten of Phillips make cat no.BN308C LED40S-6500 L12O PSU WH a) 35W

Installlation

LED 18W wall bracket light Phillips make cat no. BN 021 LED 10S 6500PSU GR S1

Installlation

FURNITURES - Workstation: Edge Workstation Table Size: 1200 x 600 x 750 Ht Specification: Table Top: 25mm pre lam particle board with 2mm PVC edge lipping. Understructure: Powder coated 50 x 50 perform legs & 40 x20 cross beam support. Front Modesty. Main Screen: 12 mm fabric magnetic screen Return Screen : 12 mm fabric magnetic screen Wire management: 125ht metal raceway cover for easy wiring /maitenance. Pre punched slots are provided on raceway for one 8 module (Ancor Roma) & one data port for mounting the switch /sockets. 2 wire manager grommets on table top for access. Wire entry cover included. MOBILE PEDESTAL 2D+1F Pedestal : Pedestal are made of 18mm thick PLB with 2 drawer units and 1 filling folder unit. The Drawer units are made mobile with the use of castors. The drawer units are provided fingergroved handle and suitable locks. CPU TROLLEY AND KEYBOARD TRAY Make: Featherlite/Steller

Director's Cabin Table Model: HT 528 Main table Size: 1800 x 750 x 780 H Side Unit Size: 905 x 440 x 750 H Material used MDF + Particle board of 50 mm thickness. Surface melamine finished. Wire manager included. Colour: Dark walnut. Make: Featherlite/Steller

Director's Cabin Office Cabinet Model: HT 325 Size: 1800 x 400 x 2000 H Material used MDF + Particle board of 25 mm thickness. Surface melamine finished. Colour: Dark walnut. Make: Featherlite/Steller

Cabin 1, 2 & 3 Tables Model: VMT 1575 Main Table Size: 1500 W x 750 D x 750ht Specification: TABLE TOP- 25mm Thick Pre-Laminated Particle Board(PLPB) finished with 2mm thick PVC Edge Banding. SUPPORTS- Supported on 25mm thick Pre-Laminated Particle Board(PLPB) Gable Ends &18mm thick Pre-Laminated Particle Board Modesty panel, with suitable spacers & levellers. Side Storage Unit Size: 900 x 450 x 750 HT structure is made out of 18mm Thick Pre-Laminated Particle Board. The shelves are adjustable in height. The shutters are fitted with auto-closing hinges.Recessed Aluminium handles, central locking system, levellers & other necessary hardware are provided. PEDESTAL UNITS Made of 18mm Thick Pre-Laminated Particle Board board with 2 Equal Drawer + 1 Filing Drawer arrangement. Castors are provided for easy mobility of the pedestal. Recessed Aluminium handles, central locking system & other necessary hardware are provided. Keyboard tray without mousepad and cpu trolley. Make: Featherlite/Steller

Reception Table Model: Edge Table Size: 1500 x 600 x 750 Ht Specification: Table Top: 25mm pre lam particle board with 2mm PVC edge lipping. Understructure: Powder coated 50 x 50 perform legs & 40 x20 cross beam support. Front Modesty. Wire management: 125ht metal raceway cover for easy wiring /maitenance. Pre punched slots are provided on raceway for one 8 module (Ancor Roma) & one data port for mounting the switch/sockets. 2 wire manager grommets on table top for access. Wire entry cover included. MOBILE PEDESTAL 2D+1F Pedestal : Pedestal are made of 18mm thick PLB with 2 drawer units and 1 filling folder unit. The Drawer units are made mobile with the use of castors. The drawer units are provided finger groved handle and suitable locks. CPU TROLLEY AND KEYBOARD TRAY Make: Featherlite

Conference Table Model: FSCT Board Room Table MAIN TABLE : 1500W X 600D X 750HT (02 NOS) SIDE TABLE : 1350W X 600D X 750HT (4 NOS) SIDE TABLE : 2100W X 600D X 750HT (2 NOS) Table Top : Table top 25mm thick pre laminated particle board finished with 2mm edge lipping. Support : Supported on 25 mm thick PLB Gable Ends with necessary cross beams. Modesty Panel : 18mm thick PLT Modesty Panel of 450 mm ht is considered. Wire Management - 10 nos. 300mm Flip up with cable dump and 3 No. wire entry cover. Make: Featherlite/steller

Director's Main Chair Model: FP Optima HB Base: The 640mm dia (26 inches) five pronged base is made out of GF nylon – Reinforced with bottom ribbing for additional buttress and strength. Tested prudently and rigorously as per ANSI/BIFMA X5.1-2011 General Purpose Office Chair Standards Gaslift - Class 4 tested -ANSI BIFMA performance standards Seat and back is made out of 12mm molded hot pressed plywood in ergonomic shape fitted with Imported T-nuts and revited in to the wood Upholstery: Cushion with pre moulded foam of 50 - 60 density in the shape of plywood. Density -- 52 kg/m3 Hardness -- 12.6kgf at 25% Distinctively and characteristically designed tilt mechanism offering a very smooth and fluidic reclining motion with tension adjust knob and importantly offering seat to back recline ratio of 3:7, optimal for good back support . Multilock mechanism is fabricated from CR Sheets,undergo through CO2 welding process imparting uniform surface finish and tensile strength. The components are processed with high degree of precision and care so as to assemble with other parts in perfect harmony to give smooth and effortless reclining experience Tension springs are made out Grade II material conforming to Indian Standards. Also provided with release levers for locking mechanism and height adjustment of seat. Mechanism aides to operate the height adjustment, and has been equipped with 4 locking positions, back rest “ Return Prevention” function Adjustable Lumbar Support Allows you to adjust the lumbar support position for good back support and blood circulation Tension control is below Seat Moulded polyurethene Arms confirming to IS 7078 with steel inserts for long life. 2 way adjustable - Height & Swivel Adjustable. Seat is duly upholstered with approved with approved Fabric Make: Featherlite/Steller

Cabin 1, 2 & 3 Main Chair Model: Liberate HB Base: The 640mm dia (26 inches) five pronged base is made out of GF nylon – Reinforced with bottom ribbing for additional buttress and strength. Tested prudently and rigorously as per Castors - Twin Castors 50mm dia castors compling to ANSI / BIFMA X 5.1 – 2002 Gaslift: Class 4 tested -ANSI BIFMA performance standards Seating Structure: Seat and back is made out of 12mm molded hot pressed plywood in ergonomic shape fitted with Imported T-nuts and revited in to the wood Upholstery: Upholstery: Cushion with pre moulded foam of 50 - 60 density in the shape of plywood. Density -- 52 kg/m3 Hardness -- 12.6kgf at 25% Mechanism: Distinctively and characteristically designed tilt mechanism offering a very smooth and fluidic reclining motion with tension adjust knob and importantly offering seat to back recline ratio of 3:7, optimal for good back support.Multilock mechanism is fabricated from Sheets, undergo through CO2 welding process imparting uniform surface finish and tensile Sheets, undergo through CO2 welding process imparting uniform surface finish and strength. The components are processed with high degree of precision and care so as to assemble with other parts in perfect harmony to give smooth and effortless reclining experience. Tension springs are made out Grade II material conforming to Indian Standards. Also provided with release levers for locking mechanism and height adjustment of seat. Mechanism aides to operate the height adjustment, and has been equipped with 4 locking positions, back rest “ Return Prevention” function Back: Mesh fabric used for back upholstery With Unique Dynaflex Two Piece Back Construction , Dya Flex provides a comfotable cushioning that stimulates the spine & abdominal muscles to promote a healthy posture & back .Inbuilt body flex lumbar support that synchronises perfectly with your back in all positions of recline. Tension Control : Tension control is below Seat Armrest: Moulded polyurethene Arms confirming to IS 7078with steel inserts for long life. One way adjustable - Height Adjustable. Fabric: Seat is duly upholstered with approved fabric Make: Featherlite

Director's, Cabin 1, Cabin2 & Cabin 3 Visistor's Chair Model: Astro VA Frame: The frame is made out of 25.4mm tube of 16 gauge tube confirming to IS-7138-1973, Welded by Co2 welding process for uniform surface finish and higher tensile strength perforation on the sheet is of uniform 2.5mm dimension and gives good ventilation. Powdercoating: Thermo set powder coating epoxy polyester hybrids of harness (pencil) H.B.74 and impact resistant (in lab) 60-160 kgs cm and to a thickness of 40-50 microns is carried out of 7 step pretreatment process. Fasters: High quality metal screws and tension fasteners conforming to Hardness 38-44 and tensile strength – 1300 n/mm. IS 1363-196 Seating Structure: Seat is made out of 12mm molded hot pressed plywood in ergonomic shape fitted with Japanese Nagayama-nuts and revited in to the wood Upholstery: Cushion with pre moulded foam of 50 - 60 density in the shape of plywood. Density -- 52 kg/m3 Hardness -- 12.6kgf at 25% Armrest: This arms are made out of polypropylene injection moulding component which offers the smooth finishes and Scratch resistance Back: Mesh Back on Frames Fabric: Seat are duly upholstered with approved fabric Make: Featherlite/Steller

Conference Head Chair Model: Liberate HB Base: The 640mm dia (26 inches) five pronged base ismade out of GF nylon – Reinforced with bottom ribbing for additional buttress and strength. Tested prudently and rigorously as per Castors - Twin Castors 50mm dia castors compling to ANSI / BIFMA X 5.1 – 2002 Gaslift: Class 4 tested -ANSI BIFMA performance standards Seating Structure: Seat and back is made out of 12mm molded hot pressed plywood in ergonomic shape fitted with Imported T-nuts and revited in to the wood Upholstery: Upholstery: Cushion with pre moulded foam of 50 - 60 density in the shape of plywood. Density -- 52 kg/m3 Hardness -- 12.6kgf at 25% Mechanism: Distinctively and characteristically designed tilt mechanism offering a very smooth and fluidic reclining motion with tension adjust knob and importantly offering seat to back recline ratio of 3:7, optimal for good back support.Multilock mechanism is fabricated from Sheets,undergo through CO2 welding process imparting uniform surface finish and tensile Sheets, undergo through CO2 welding process imparting uniform surface finish and strength. The components are processed with high degree of precision and care so as to assemble with other parts in perfect harmony to give smooth and effortless reclining experience. Tension springs are made out Grade II material conforming to Indian Standards. Also provided with release levers for locking mechanism and height adjustment of seat. Mechanism aides to operate the height adjustment, and has been equipped with 4 locking positions, back rest “ Return Prevention” function Back: Mesh fabric used for back upholstery With Unique Dynaflex Two Piece Back Construction , Dya Flex provides a comfotable cushioning that stimulates the spine & abdominal muscles to promote a healthy posture & back . Inbuilt body flex lumbar support that synchronises perfectly with your back in all positions of recline. Tension Control : Tension control is below SeatArmrest: Moulded polyurethene Arms confirming to IS 7078 with steel inserts for long life. One way adjustable - Height Adjustable. Fabric: Seat is duly upholstered with approved fabric Make: Featherlite

Conference , Workstation & Reception Chair Model: Opus MB A-FUR-CHR-M-01 High back revolving chair Medium revolving chair back for support. Back : Netted backrest for air circulation which can mould Adjustable lumber support Automatic backtilt tension adjustment based on user's body weight. Seat : Cushioned seat with soft PU (Poly Urethane) foam with best quality sweat absorbing cover. Aluminium metal 5 pronged pedestals Multi position locking with anti shock feature Adjustable seat height with Gas Lift Hydraluic system Armrest : Soft PU ( Poly Urethane) top with Saddle support & Height adjustment approx. dimesions : Width x Depth x Height: 76 cm x 76 cm x 100 - 109 cm Seat Height : 45 - 54 cm Overall Ergonomic design for office use. Make: Featherlite/Steller

Center Table Model: Ambassador center table Size: 1000 x 500mm Teak wood rectangular wooden table - Glass top of 8 mm thickness. Make: Featherlite/Steller

Sofa Model: Interact Sofa 902 Specification: Made off: The sofa is made of fine quality leatherette. (3s = 8.0 mtr, 2s = 6.8 mtr, 1s= 5.3 mtr), the structure is made from silver wood & pine wood, 32 & 40 density foam is used which is covered with roll poy filling for giving comfort and extra softness to sofa. Extra material used for 902 sofa e elastic nevar belt, stapler pins (Kangaro company) Legs are made of stainless steel. Make: Featherlite/Steller Two seater sofa 1275 W X 710 D X 780 H

Storage Model: KD 034 Size: 900WX400DX 1850H Metal storage with two door Color: Grey Make: Featherlite/Steller

Khitish Ojha

Sri Ravi Kumar Gupta