Provn of 02xtoilets near Bldg No. P-114 at Corps Camp, Construction of toilet block at Bldg No. P-33 Escort line and Provn of certain minor works at Yol Cantt

Amount

Excavation in trenches n exc 1.50 metre wide & n exc 1.50 metre in depth for foundation etc or for shafts, wells, cesspits manholes, pier holes etc n. exc 10 Sqm on plan n exc 1.50 metre in depth and getting out in any type of soil, complete all as specified and directed.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc. 25cm thick each layer of soil, complete all as specified and directed.

Removing excavated material not exc. 50m and depositing where directed at a level not exc. 1.50m above the starting point, complete all as specified and directed.

Plain cement concrete M-7.5, nominal mix, D-2, using 40mm graded mechanically crushed stone aggregate as in foundation, filling and mass concrete, complete all as specified and directed.

Reinforced cement concrete (nominal mix) M-15, type B-1 using 20mm graded crushed stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and directed. Note:- Reinforcement and form work shall be measured and paid separately.

Reinforced cement concrete (nominal mix) M-15, type B-1 using 20mm graded crushed stone aggregate as in columns, pillars, piers, posts and struts, complete all as specified and directed. Note:- Reinforcement and form work shall be measured and paid separately.

Reinforced cement concrete (nominal mix) M-15, type B-1 using 20mm graded crushed stone aggregate as in beams, cantilevers, bressummers, lintel over 1.50m span, complete all as specified and directed. Note:- Reinforcement and form work shall be measured and paid separately.

Reinforced cement concrete (nominal mix) M-15, type B-1 using 20mm graded crushed stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed. Note:- Reinforcement and form work shall be measured and paid separately.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) in rough finished flat surface of concrete, complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20cm wide and sides of RCC/ PCC bands in walls, sides of slab, horizontal or sloping and similar work exc 10cm but not exc 20cm wide for roughly finished flat surfaces of concrete, complete all as specified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, for roughly finished flat surfaces of concrete, complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions, for fair finished square, rectangular or polygonal surfaces of concrete, complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. For fair finished flat surfaces of concrete, complete all as specified and directed.

TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips, complete all as specified and directed.

TMT bars 5 to 10mm dia cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips as in stirrups, spacers and binders, complete all as specified and directed.

Fly ash brick work with old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified and directed.

Brick work with old size fly ash bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 (1 cement : 4 coarse sand), complete all as specified and directed.

Hard core of broken stone or boulders of gauge not exc. 63mm deposited, spread and levelled in layers not exc. 15cm thick, watered and rammed to a true surface, complete all as specified and directed.

Plain cement concrete M-7.5, nominal mix, type D-2, using 40mm graded mechanically crushed stone aggregate as in sub base, 75mm thick, surface finished even and fair, complete all as specified and directed.

Rendering cement plaster 15mm thick in two layers (first layer 10mm thick and second layer of 5mm thick) in cement mortar 1:6 (1 cement : 6 coarse sand) on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, complete all as specified and directed.

Rendering cement plaster 15mm thick in two layers (first layer 10mm thick and second layer of 5mm thick) in cement mortar 1:4 (1 cement : 4coarse sand) on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, complete all as specified and directed.

Rendering cement plaster 10mm thick in cement mortar 1:3 (1 cement : 3 coarse sand) on ceiling, surface finished even and smooth without using extra cement, complete all as specified and directed.

Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over a coat of chalk whitening primer including preparation of surface, complete all as specified and directed.

Preparation of newly plastered wall surfaces and appling two coats of cement base paint over a coat of primer, complete all as specified and directed.

Three coats of white wash on newly plastered ceiling surfaces including preparation of surfaces, complete all as specified and directed.

Plain cement concrete M-10, nominal mix, type C-2, using 40mm graded mechanically crushed stone aggregate, 75mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5cm deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), complete all as specified and directed. Note:- The unit rate include for use of form work (straight or curved).

Plain cement concrete M-15, nominal mix, type B-0, using 12.50mm graded mechanically crushed stone aggregate as in flooring/levelling course, 25mm thick, surface finished even and fair to receive floor finishes surface, complete all as specified and directed.

15mm thick screed bedding or bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand) for laying floor finishes/tiles, complete all as specified and directed.

Mat finish joint less (non skid), Premium class I grade, coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.18 Sqm but not exc. 0.38 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and directed.

Glazed ceramic coloured tiles joint free of size 350 x 250 / 450 x 300 x 7mm thick as in vertical surfaces jointed in neat cement slurry and pointed with coloured cement to match over and including 10mm thick plastering in cement mortar 1:4 (1 cement : 4 coarse sand), complete all as specified and directed.

Vitreous China wash down water closet (pedestal pattern), white including traps, connection to drain or outgoing pipe, anti-syphonage pipe complete including necessary fittings, fixed, complete all as specified and directed.

Supply and fixed PVC valveless, syphonic action type flushing cistern 10 litres capacity low level with inlet, ball valve, float and handle with brackets including 32mm dia PVC long bend flush pipe 90cm long and 15mm dia PVC connection 450mm with PTMT of nuts with coupling and PVC washers at both ends, fixed, complete all as specified and directed.

Wash basins, Vitreous China (Flat back) size 550mmx400mm, crystal white with and including cutting for and pinning on ends of brackets, 450mm long PVC connections 15mm size long with CP coupling nuts at both ends, waste pipe of polythylene of low or high density or PVC of 32mm dia, chain and plug, porcelain stopper, and fixed, complete all as specified and directed.

Bib taps, fancy type long body 15mm bore, cast copper alloy with crutch or butterfly handle, screwed down, chromium plated screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

Stop/Angle valve, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed, complete all as specified and directed.

Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed of 15mm bore and fixed, complete all as specified and directed.

Soap dish, vitreous China white, approximate size 160x160x90mm, chromium plated, fixed to plugs with chromium plated, brass screws, fixed, complete all as specified and directed.

Rotational moulded polyethylene water storage tank 500 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position including brass ball valve 20mm dia epoxy coated aluminium rod with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line, complete all as specified and directed.

Gun metal, globe or gate valves, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 20mm bore iron pipe or for unions and fixed, complete all as specified and directed.

Mild steel galvanized iron water tubing 15mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor, complete all as specified and directed.

Mild steel galvanized iron water tubing 20mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor, complete all as specified and directed.

Mild steel galvanized iron water tubing 25mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor, complete all as specified and directed.

PVC (SWR) bends any radius, 110mm bore any type with ovel access door and jointing with solvent cement, fixed, complete all as specified and directed.

PVC (SWR) bends any radius, 75mm bore any type, jointing with solvent cement, fixed, complete all as specified and directed.

PVC (SWR) floor trap, plain with grating including jointing to waste pipe with solvent cement, dia of outlet 75mm, fixed, complete all as specified and directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall with adjustable clamps of bore 110mm, complete all as specified and directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall with adjustable clamps of bore 75mm, complete all as specified and directed.

PVC connection 15mm size with PTMT nuts at boths end 450mm long and fixed, complete all as specified and directed.

Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms), complete all as specified and directed.

Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonary with top ring of M-25 concrete including intercepting chamber and screen chamber made of brick masonary in CM, RCC cover slab in M-25 SFRC cover, inter connecting pipes of RCC/DWC complete filled with brick bats of size 1.80m dia 3m depth, complete all as specified and directed by Engr-In-Charge. drg No CEPZ/C-TD/013/13 sheet No 1/5 to 5/5.

Damp proof course 25mm thick cement mortar 1:2 to horizontal or vertical surfaces including necessary formwork, complete all as specified and directed by Engr-In-Charge.

Factory made solid PVC Door/window/ventilator Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet and edges shall be painted to match with prelam sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 180 of MES SSR 2020 Part-II, complete all as specified and directed.

Factory made fully glazed PVC (frosted/ground/obscured) window/ventilator shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; complete all as specified and directed. Note:- Glass gauges inclusive of quoted rates.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain coloured PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site, Sheet No 1/1), complete all as specified and directed.

Butt hinges (ISI marked), medium weight, cold rolled, mild steel 100mm long, fixed, complete all as specified and directed.

Mild steel barrel tower bolt (ISI marked), stove enamelled black, with bright bolt and fixed of size 150mm and fixed, complete all as specified and directed.

Removing excavated material exc 250m but not exc. 500m and depositing where directed at a level not exc. 1.50m above the starting point, complete all as specified and directed.

M&L for 150mm reinforced concrete pipe, class NP2, drain pipes laid in tenches and joints, complete all as specified and directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors bore 110mm, complete all as specified and directed.

PVC (SWR) reducer 110mm bore, complete all as specified and directed.

Salt glazed stoneware gully traps, size 150x100mm square or round mouthed, type 'P', complete all as specified and directed.

Cutting into existing manholes for connecting new drains, any dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round 3/4 channel) in cement concrete M-15 type B-1 smooth, finished and reforming benching as required, complete all as specified and directed by Engr-In-Charge.

Precast cement M-15 nominal mix, type B-1, using 20mm graded crushed stone aggregate as in landings, cover slab (for manholes etc.), chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including chamfers, weatherings, throating etc. and setting in cement mortar 1:4 complete with joints to match, complete all as specified and directed.

RCC M-15, nominal mix, B-1 using 20mm graded mechanically crushed stone aggregate as, in lintels bend up to 1.50 metre clear span cuts, steps seismic and other similar bends, coping, bands plates for serving hold fasts etc. and the like including weathering slighting rounded or chamfered angles and throating, complete all as specified and directed. Note:- (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement shall be measured and paid separately.

Fly ash brick work with old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:4 (1 cement : 4 coarse sand), complete all as specified and directed.

Damp proof course 25mm thick In cement concrete 1:2:4, type B-0 to horizontal or vertical surfaces including necessary formwork, complete all as specified and directed by Engr-In-Charge.

Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over 2mm thick plaster of paris putty including preparation of surface, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of wall to prepare the surface even and smooth and applying finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm), complete all as specified and as directed.

S&F false ceiling of Non asbestos (Designer) 4mm fibre cement building boards, manufactured from homogeneous mixture of cement, quartz and cellulose and cured with high pressure steam using auto claving process confirming to IS-14862, of size 600 mm x 600 mm x 4 mm thick fixed over and including galvanise iron powder coated (minimum thickness of powder coating 50 micron) snap grid frame work of T section (main & cross member) of size 25 mm x 25 mm x 1.50 mm thick in square pattern of grid size 600mm X 600mm. The frame work will supported on side wall with the used of aluminium 'L' section of size 25 mm x 25 mm x 1.50 mm angles etc. Snap grid shall be supported with hangers of 4 mm dia galvanised iron wire adjusting level fixed to roof slabs / truss etc by means of ceiling cleats made out of galvanised iron flat of size 40 x 3 mm size 60 mm long and expansion hold fasteners 12.50 mm dia 40 mm long complete all as specified directed by the Engineer-in-Charge. Make : Everest or equivalent as approved by GE.

Rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to grade Fe.410-W Gde E-250, quality A, steel work, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall with two corrugations side lap, fixed with self tapping screws and washers, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws and washer, complete all as specified and directed.

WPC (Wood Polymer Composit) Double Prelam Door Frame (Chowkhat) of Size 120mm x 50mm with a wall thickness of 5mm(+/- 0.25), made out of extruded 5mm (=0.25) mm thick PVC Sheet of Density 600kg/cbm manufactured and ISO 9001-2015 certified company and by joining 3 Nos heat moulded PVC sections. The high section of size 35 x35 mm shall be made from plain colour PVC sheet of 5mm (=/- 0.25 mm) thickness. The inside section will be covered with 5mm thick PVC sheet 'C' shape covering section of size 120mm x 50mm. At centretop position 5mm (+0.25mm) thick 50 x50 x50 mm pattam section should be pasted with solvent cemen adhesive to make double pattam of frame. The frame shall be mitre cut at two corners & joined with 4 nos of 150mm long 'L' brackets of 19 x 19 mm M.S sq, tube or fusion heat welding process. The two vertical door frames are to be reinforced with 25 x 25 mm M.S sq tube of 19 gauge throughout the frame. The Door Frame shall be fixed to the wall using 8/100mm fischer screws. A minimum of 4 nos of screws to be provided for each vertical member & minimum 2 Nos. for horizontal member etc. complete as per manufacture's specification & direction of engineer-in charge.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of solid core single Leaf Flush Door of 25mm thickness, lipped with 15mm (5mm x 3) thick x 30 mm width on one stiles and top rails & 10mm (5mm x 2) thick x 30 mm width on the other stiles & bottom rails. The inner panel Laminated with 2mm thick termite proof, water proof & fire resistant moulded PVC sheet with 2,4,6 raised panel design in different plain & or prelam colors on one side after routing the mouldd design on flush door & 2mm plain and/or prelam PVC sheet on other side using rubber based adhesive on flush door & solvent cement adhesive on the lipping etc. complete as per direction of Engineer-in-charge, manufacture's specification and drawing.

Plain cement concrete M-10, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 50mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5cm deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), complete all as specified and directed. Note:- The unit rate include for use of form work (straight or curved).

2nd class hard wood (Sal/Hollock) plain, solid, straight chowkats and frames, wrought, framed, rebated on solid, rounded or chamfered, put together with glue, pinned at joints with one or more rebates, complete all as specified and directed.

Factory made 2nd class hard wood (Sal/ Hollock) plain, framed, panelled 35mm thick shutters without interlocking rail and with one panel and panels of 9mm BWP commercial plywood or 12mm veneered particle with commercial face veneers on both sides.The size of rail and style as per IS–1003 (Part-I), kiln seasoned and chemically pressure treated, complete all as specified and directed.

Applying two coats of synthetic enamel paint over a coat of pink primer on new wood or wood based surfaces of any description, exc. 10cm width or girth including preparation of surfaces, complete all as specified and directed.

Extruded aluminium alloy handles (ISI marked), fabricated type, anodised, of size 150mm, complete all as specified and directed.

Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 100mm, fixed, complete all as specified and directed.

Mat finish joint less (non skid), Premium class I grade, coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.18 Sqm but not exc. 0.38 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified and directed.

Mat finish, premium quality, coloured/ printed ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, as in skirting, dado etc. set and jointed in neat cement slurry and includingincluding 10mm thick rendering in cement mortar (1:3) including necessary cutting as per site requirement complete all as specified and directed. including necessary cutting and waste as per site requirement pointed in white or coloured cement to match, complete all as specified and directed.

Marble 16 to 18mm thick, green marble, (table rubbed and polished and moulding of outer edges) as in floor, kitchen cooking platform /shelf and verticle surfaces duly machine cut in skirting /dado and like laid over and including 15mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade green marble type, complete all as specified and directed.

Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors, complete all as specified and directed.

Wash basins, Vitreous China (flat back or angle back type) white, corner or flat of size 450mmx300mm, excluding taps, waste, chain and plug and porcelain stopper but including brackets, cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe, complete all as specified and directed.

Low density polyethylene (LDPE) pipes 32mm dia bore of pressure rating 6 kgf/sq. cm, complete all as specified and directed.

Bib taps, fancy type 15mm bore, cast copper alloy with crutch or butterfly handle, screwed down, chromium plated screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

PVC connection 15mm size with PTMT nuts at boths end 600mm long and fixed, complete all as specified and directed.

Vitreous china permium/1st quality wash down water closet wall hung EWC white/ivory/gel gasket etc. including fixing of plastic water closet seat cover, block/white closed pattern with flat bottom and cover and mild steel chromium plated hinging device, flushing cistern (excluding flushing cistern and flush pipe) and fixed, complete all as specified and directed.

Vitreous Chinaware squatting pan, ‘Orrisa pattern’ size 580 mm x 440 mm, snow white, with CI ‘P’ or ‘S’ trap, front or back inlet, integral foot rest with provision of plain cement concrete M-15, type B-1 using 20mm graded crushed stone aggregate, including making connections to trap and to flush pipe including CP jet etc complete all as specified, anti-syphonage pipe, fixed, complete all as specified and directed.

Urinal with automatic sensor, an automatic flush valve, sealed battery pack, a plastic chromed cover frame that can be attached to wall and other fixing materials for attaching the cover frame and box to the wall, complete all as specified and directed by Engr-In-Charge.

Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms), complete all as specified and directed by Engr-In-Charge.

Applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel or steel based surfaces of any description, exceeding 10cm width or girth including preparation of surfaces, complete all as specified and directed.

Rolled sections as in Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161- 1979 grade St.-240s, steel work, complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.50 cum, getting out in any type of soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, complete all as specified and directed.

Plain cement concrete M-15, nominal mix, B-2, using 40mm graded mechanically crushed stone aggregate as in foundation, filling and mass concrete, complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete including removal of debris to a distance exc 1.50 km but n.exc 2 km, complete all as specified and directed.

Cutting openings, through brick walls built in cement mortar or cement lime mortar for door, window and other openings or enlarging existing openings. converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc. to store and rubbish not exc. 50m, complete all as specified and directed.

Anodised aluminimum frame powder coated for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc., complete all specified and as directed by Engr-in-charge.

Anodised aluminium door shutters power coated, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc., complete all specified and as directed by Engr-in-charge.

Anodised aluminium powder coated window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.) hinges type B-21 100mm long (2 no.) suitable handle (1 no.), complete all specified and as directed by Engr-in-charge.

Sheet glass 4.80 mm to 5.50mm thick ordinary quality and glazing with oil putty/aluminium beads in squares, not exc. 0.50 sqm in each pane, complete all as specified and directed.

Mortice lock, brass, vertical type, size 100mm, 4 lever, fixed, complete all as specified and directed.

Taking down cement plaster on brick or stone walls, ceiling, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete including removal of debris to a distance exc 1.50 km but n.exc 2 km, complete all as specified and directed.

Rendering cement plaster 15mm thick in cement mortar 1:6 (1 cement : 6 coarse sand) on other than fair faces of brick wall or on stone masonry surfaces, surface finished even and smooth without using extra cement, complete all as specified and directed.

Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) on fair faces of brick wall or concrete surfaces, surface finished even and smooth without using extra cement with WPC @ 3% weight of cement, complete all as specified and directed. Note:- water proofing compound shall be included in quoted rates.

Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over a coat of primer over 1mm thick wall care putty including preparation of surface, complete all as specified and directed.

Preparation of old decorated plastered or unplastered surfaces including cleaning by brooming down or with steel wire brushing scraping down smoke soot, moulded moss and efflorescent salts and cleaning oil and greasy spots applying two coats of oil bound distemper including a coat of primer over 1mm thick wall care putty on walls, complete all as specified and directed.

Preparation of old decorated plastered or unplastered surfaces including cleaning by brooming down or with steel wire brushing scraping down smoke soot, moulded moss and efflorescent salts and cleaning oil and greasy spots and applying two coats of cement base paint over a coat of primer on walls including cleaning the floor / joinery surfaces, glass pans, complete all as specified and directed.

Stainless steel wire cloth 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with galvanised wire staples or tinned tacks, fixed, complete all as specified and directed.

Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions i.e at top, bottom and sides with required EPDM rubber/neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/panelling, CP brass/stainless steel screws, complete all as per architectural drawings and the direction of Engr-In-Charge.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in any type of soil, complete all as specified and directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

Plain cement concrete M-15, nominal mix, B-0 using 12.50mm graded mechanically crushed stone aggregate as in lintels upto 1.50 metre clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, chamfered angles and throating, complete all as specified and directed. Note :- (i) The unit rate include for use of form work (straight or curved).

Mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed ballusters walk ways; railings; framework of water tanks and similar work conforming to Fe.290. Gde-E-165, complete all as specified and directed.

Reinforced cement concrete (design mix) M-25 (using 20mm graded crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed. Note:- Reinforcement and form work shall be measured and paid separately.

Point wiring with 1.50 Sqmm copper conductor FRLS (Multi strand) PVC insulated ISI Marked unsheathed cable in and including concealed PVC conduit, ISI marked of suitable size with all fittings/ accessories such as bends, cross, elbow, tees etc. of suitable size and also including PVC insulated ISI marked unsheathed 1.50 Sqmm copper multistranded conductor FLRS as phase, neutral and earth wire connected to common earth dolly and including concealed MS pressed steel of suitable sizes (modular sunken box) terminal boxes made from 1.60 mm thick sheet for mounting of switches, sockets, fan regulators, light fittings etc. and modular cover plate as top cover for one light point/exhaust fan point, controlled by one way switch complete all as specified and directed. Note:- (i) Wiring colour code i.e Red/Yellow/Blue for phase, Black for neutral and Green for earth shall be maintained. (ii) Point wiring is considered for modular switches and sockets. Rate of metallic sunken box and other connected accessories required for modular point wiring included in quoted rates. (iii) Rate of modular switch and sockets will be paid seperately under relevant item. (iv) Rate of cutting chases, cement plaster, white wash and making good as existing surface included in quoted rates.

All as per serial item No '118' above, but for one 3 pin 5 Amps socket outlet on the independent board with 1.50 sqmm FRLS PVC copper conductor cable and FRLS PVC insulated, unsheathed 1.50 sqmm stranded copper conductor cable as continous earth wire, complete all as specified and directed.

All as per serial item No '118' above, but for one 3 pin 5 Amps socket outlet on the same board with 1.50 sqmm FRLS PVC copper conductor cable and FRLS PVC insulated, unsheathed 1.50 sqmm stranded copper conductor cable as continous earth wire, complete all as specified and directed.

All as per serial item No '118' above, but for 3 pin 15 amps socket out let on independent with 2.50 Sqmm FRLS PVC copper conductor cable and FRLS PVC insulated, unsheathed 2.50 Sqmm stranded copper conductor cable as continuous earth wire, complete all as specified and directed.

S & F for modular switch, 6A one way, single module, complete all as specified and directed.

S & F for modular switch 16A one way with indicator, single module, complete all as specified and directed.

S & F for modular socket for 6A 2/3 pin combined, 2 module, complete all as specified and directed.

S & F for modular socket for 6A/16A 3 pin combined, 2 module, complete all as specified and directed.

M & L for ceiling rose 65 x 50mm three terminals, fixed, complete all as specified and directed.

Supply and fixing of LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V, AC recessed/surface type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size, complete all as required at site and directed by Engr-in-Charge. Make:- Wipro LED 2x2 Cart Part No. CRCO10S038HP57GL1, Philips

Supply and fix exhaust fan, steel body AC single Phase, 230V of size 300m sweep with, blades, and frame and louvers, complete all as required at site and directed by Engr-in-Charge.

Hand dryer single phase 230V, 50Hz high speed brushed motor 15000 RPM, minimum air speed 90 m/s not less than 500W, iron/PVC body, complete all as required at site and directed by Engr-in-Charge.

Supply and fixing LED light fitting mirror type with high output diffuser 2 feet, 10 watt, 6000 K, 220 volts, AC decorative type with extruded polycarbonate having efficiency 120 lumens /watt with driver holder including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed. Make: Wipro, Philips

S & F for MCB SP 6 to 32 amps 240 Volt,10 KA, 'B' series, complete all as specified and as directed.

S & F for MCB SPN 40 amps 240 Volt,10 KA, 'B' series, complete all as specified and as directed.

Sheet metal enclosures factory made flush fixed for DBs when MCBs to be used, single pole and neutral (double Door powder coated), 8 way, 240 volts with 200 Amp rated bus bar, complete all as specified and directed.

Supply and installing of the electric water storage heater of ABS body type of 25 litre capacity with rated power 2 KW, BEE, 5 star rated, vertical type, thermally insulated Mild steel tank with glass line coating inside the tank alongwith glass lined incoloy heating element with anti corrosive magnesium anode, NRV, thermostate, indicators and temperature adjustable knob including steel braided flexible connection for pipe of size 15mm dia bore GI hexagonal adopters/Nuts on both side of inlet (cold water supply) and outlet (hot water supply) and including provision of wall mounting arrangement and mounting on wall with suitable size of anchor bolts with complete connection of water including testing after installation, complete all as specified and as directed by Engr-In-Charge.

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 10 sqmm 2 core nominal cross section in service connections, complete all as specified and directed.

Replacement of earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground to a depth not less than 2.25m below normal ground level with top edge of earth plate at a depth not less than 1.50m below ground level, earth plate surrounded by 15cm thick packed layer of charcoal and common salt alternatively upto 90cm and connected with and including galvanised iron strip 25mm X 4mm (as earth lead strip), by means of bolts, nuts, check nuts and washers of GI pipe 15mm bore light grade for protection from earth plate up to testing point for protection of strip, 20mm bore GI pipe medium grade for water with wire mesh and funnel for watering including necessary excavation and earh work, PCC chamber 1:3:6 type C-2 with 40mm thick cover of rainforced cement concrete M-15 reinforced with XPM (weight not less than 4 kg/Sqm) and frame of angle iron 40x40x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape and and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50m, complete all as shown in electrical plate No. 03 of MES Schedule Part-I, complete all as specified and directed. Note:- (i) RCC pit cover shall be precast of RCC 1:2:4 type B-1, reinforcement with 8mm TOR steel @ 100 c/c in lieu of CI cover and the rate includes in the unit rate of item. (ii) Earth electrodes shall be protected upto test point using necessary arrangement with suitable size GI pipe upto 7.50m and the rate includes in the unit rate of item. (iii) Earth pit chamber and RCC cover shall be painted with red paint over a primer coat and rate includes in the unit rate of item.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250m, complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of plate not less than 1.50m below ground level, connecting to galvanised iron wire 4.00mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15mm bore including provn of concrete pit in plain cement concrete M-20 type B-1 using 20mm graded crushed stone aggregates with 40mm thick cover of rainforced cement concrete M-20 reinforced with XPM (weight not less than 4 kg/Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50m, all as per electrical plate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion. NOTE :- Item of earthing includes the cost of 7.5 m long galvanised iron earth wire 4mm size and protection pipe of 15mm bore galvanised iron light grade and earth work.

Supply and fixing of LED street light fitting 35W 230V, AC, outdoor type with high pressure die cast aluminium housing with street optic lens and glass diffuser for uniform light distribution and inbuilt surage protection device (SPD) and heat resistant complete with driver, street light bracket made out of GI pipe 32/40mm dia medium grade GI pipe minimum 1.50m long including fixing with 02 Nos MS clamps made out of flat iron of size 30mmx5mm with nuts, bolts and washers including painting with impact and corrison resistant including thermal management in multiple optics complete with IP 65/66 protection complete K=6500K, complete all as specified and directed by Engr-In-Charge.

S & F for MCB SPN 32 amps 240 Volt,10 KA, 'B' series, complete all as specified and as directed.

Supply and fixing of wall mounted fan, AC single phase, 230V of size 400mm sweep heavy duty swing style, air flow capacity 500cc/sec etc., complete all as specified and directed by Engr-In-Charge.

Supply and fix switch piano flush type one way 6 Amps, 1 module, 230V, complete all as specified and directed.

Supply and fix switch piano flush type one way 16 Amps, 1 module, 230V, complete all as specified and directed.

KISHAN CONTRACTOR (BID ID -3284481)