SPECIAL REPAIR TO BLDG NO T-180 OF 237 TRANSIT CAMP AT RAIWALA MIL STN

Amount

Dismantling Asbestos Cement (Corrugated, Semi corrugated etc.) sheets in roof coverings.

S&F Pre-painted galvalume aluminium zinc coating AZ-150 GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall and gutter, fixed with self tapping screws complete all as specified and directed .

S&F Pre-painted galvalume aluminium zinc coating AZ-150 GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed .

Taking down roof trusses, coupled rafters or trussed beams trusses above 4 mtr & upto 8 mtr etc,for renewal of any defective members (timber renewed to be measured separately) and reassembling including Housing and fixing trusses etc. after repairs including tightening up wedges, cotters bolts etc.

M&L 2nd class hard wood in scantling wrought timber framed and fixed

M&L preparing surfaces of wood and wood based materials, new or old of any description and girth, not otherwise described and treated with one coats of creosote oil

Dismantling mild steel work of any description not otherwise provided for

S & F Rolled Mild Steel sections confirming to Fe 410 - W as in main and cross beams, hip and jack rafters; purlins where connected to common rafters fixed with angle cleats or other connecting plates

S & F Mild steel work in hand rails, wind ties, as directed, including all necessary drilling, bolting or riveting etc., and similar work confirming to Fe 410 - O or Fe 310 - O

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets.

S&F false ceiling 4 mm thick with GI framed work with main tee of size 24X28.5 mm made out of PGI sheet 0.3 mm thick doubled at web and single at flange, flange covered with powder coated sheet 0.25 mm thick and wall angle 24X24X0.45 mm powder coated for celing , ceiling board 60cmX60cmX4.0 mm thick , suspended with GI wire 2 mm dia & upto 2 M average length with adjustable device complete including plugging in brick /stone wall with steel rawal plugs@ 600 mm C/C . Ceiling board shall be pressed to the ceiling tee with staple clips at all four sides and painted with two coats of Acrylic distemper tint as approved by GE/AGE including making good all the disturbed portion , complete all as specified and directed.

Demolition of brick work built in cement mortar in any description and position complete all as specified and directed.

M & L for Brick work with sub class B bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 with old size bricks.

Taking down cement plaster, terrazzo dado in any thickness from brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc including removal of rubbish, vegetation etc outside complex (MOD land) complete all as specified and directed.

M&L Rendering 15 mm thick cement plaster on concrete solid block walls in two coats first coat of 10 mm in CM 1:4 & 2nd coat of 5mm in CM 1:4 mixed with integral water proofing compound finished to even & fair. Note :- Integral water proofing liquid will be measured and paid seperately.

Supply only water proofing compound

M&L Complete removal of existing treatment by mechanised system on walls internal or external surfaces in any height complete all as specified and directed.

M&L preparation of new or plastered or unplastered and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces

M&L preparation of old or plastered or unplastered and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces

M&L Rendering 15 mm thick on fair faces of brick work or concrete walls internal surfaces in CM 1:6 finished to even & fair.

M&L preparation of new or plastered or unplastered and applying two coat of distemper acrylic oil emulsion white or tinted over and incl of one coat of alkali resistance priming paint and 1mm thick wall care putty on wall surface.Complete all as specified and directed

M&L preparation of old plastered or unplastered and applying two coat of distemper acrylic emulsion white or tinted over and incl of one coat of alkali resistance priming paint and 1mm thick wall care putty on wall surface.Complete all as specified and directed

Demolition of cement concrete (un-reinforced) in Ground floors and paving n.exe 15cm thickness ( below or above ground level ) including removal of rubbish out side complex (MOD land), complete all as specified and directed.

M&L cement concrete 1:3:6 type C-1 (using 20mm graded aggregate) 75 mm thick as in plinth protection surface finished even and fair complete all as specified and directed.

Supply only 4mm thick glass dividing strip of figured glass, pin headed type, 73mm wide insereted in position completed all as specified and directed

M & L for 75 mm thick Cement concrete type D2, 1:4:8 (using 20 mm graded granite stone aggregate) in sub base of flooring/ hard standing /footpath

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish off the premises from MoD all as specified and directed.

M&L for Non- skid coloured ceramic tiles of any design and pattern, 7 to 8 mm thick (square/rectangular) area of each tile exe 0.18 sqm but not exe 0.36, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles . Tiles shall be confirming to IS-15622.2006, Group B II with average water absorption between 3% to 6%. Length, width and straightness of sides + 0.10% (Max deviation). Thickness + 5.0% (Max deviation). Centre & Edge curvature and warpage + 0.50% (Max deviation). Breaking strength 1000 N (Minimum) and minimum 95% tiles shall be free from visible defects. Note:- Shade of the tiles including Colour, design and pattern shall be approved by AGE (I)

M&L prepolished chequered cement concrete tiles(ISI MARKED) of size 30cmx30cm x25mm thick with rubberised polish , set jointed and pointed in neat cement slurry with grey cement and pigment over and including 20mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L screed bed or bedding layer of morter 15 mm thick cement plaster 1:6 for laying floor finished to receive floor tiles/granite.

M&L for coloured glazed ceramic tiles of any design and pattern, 300x450x 7 to 8 mm thick, as in dado etc, Set and jointed in neat cement slurry and pointed in white of coloured cement to match the shade of the tiles. Tiles shall be confirming to IS-15622:2017, Group B III with average water absorption between 10% to 15%. Length, width and straightness of sides + 0.20% (Max deviation). Thickness + 4.0% (Max deviation). Straightness of sides and Rectangularity +0.15% (Max Deviation). surface flatness + 0.22% (Max deviation). Breaking strength 500 N (Minimum) and minimum 95% tiles shall be free from visible defects. Note: Shade of the tiles including Colour, design and pattern shall be got approved by AGE (I)

M/L rendering 10mm thick in cement plaster 1:4 on brick work or concrete surfaces surfaces or surfaces other than fair face of brick work to receive glazed tiles/granite

Dismantaling water tanks and removing to store exc 500 but n. exc 1000 ltrs

S&F Rotational moulded polyethylene water storage tank 1000 liters capacity, white triple layer construction (cylindrical vertical closed top), hoisted & fixed in position including all fittings complete all as specified and as directed.

S&F 20mm dia ball valve high pressure PTMT with epoxy coated aluminium rod & high pressure plastic ball screwed for iron pipe and fixed.

Taking up or down steel water tubing and connections including cleaning for refixing or removing to store 15 mm dia .

Ditto as per item above but 20 mm dia .

M&L for Mild steel galvanized steel tubing of 15 mm bore (ISI Marked) with screwed socket joints as in concealed pipe work , medium grade, together with all fittings heavy duty (ISI Marked ) (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.) and fixed complete to walls and ceiling with clips, wall hooks, wooden plugs or laid in floors Complete all as specified and directed

M&L for Mild steel galvanized steel tubing of 20 mm bore (ISI Marked) with screwed socket joints, medium grade, together with all fittings heavy duty (ISI Marked ) (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.) and fixed complete to walls and ceiling with clips, wall hooks, wooden plugs or laid in floors Complete all as specified and directed

Refixing old steel tubing of 20 mm bore and connections in new or old position (walls, ceilings, floors etc.) together with all fittings heavy duty (ISI Marked ) (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.) and fixed complete to walls and ceiling with clips, wall hooks, wooden plugs or laid in floors Complete all as specified and directed

S & F 20 mm dia Gun Metal, globe or Gate Valve with Iron wheel head Screwed both ends for Iron Pipe and fixed in repairs.

S & F in repairs 15 mm bore Stop valves (angular stop cock), cast copper alloy, fancy type, chromium plated with long shank and cup screwed down high pressure with crutch or butterfly handle or concealed screwed both ends for iron pipe or for unions.

S & F in repairs 15 mm bore chromium plated bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule.

Demolition of Reinforced Cement Concrete of any description and in any position not otherwise specifically provided for

M & L for Plain/ Reinforced Cement Concrete Type C1 1:2:4 (using 20 mm graded stone aggregate) cast in situ in lintels up to 1.5 M span, cills and other similar bands, plinth courses, parapets, copings, bed plates and the like including weathering, slightly rounded or chamfered angles and throating, as directed.

M&L RCC 1:2:4 type B1 (using 20mm graded aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc.

M & L for Fair finished flat Form work to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exce 200 mm thick.

Fair finished flat Form work to edges of concrete flats, treads, breaks infloors, window cills, concrete railings, openings in concrete walls floor and roofs not exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or slopping and similar work

M&L precast cement concrete 1:2:4, type B1 (Using 20 mm graded stone aggregate) in landings, cover slabs (for manholes etc.) shelves and similar articles with plain faces and set in cement mortar 1:4

M&L for mild steel TMT bars10mm dia, cut to length, bent to shape required including cranking bending spirally & binding with and in including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required including cranking bending spirally & binding with and in including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Dismantling of Stone slabs and tiles of any description or thickness in floors, approns, kitchen plateform / shelves etc.Complete all as specified and directed

M & L of 18-20 mm thick pre polished udaipur green stone (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

M&L for post construction Anti termite treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors.

M&L for post construction Anti termite treatmentAlong the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron

Taking down shutters of any description exc 1 sqm and n.exc 2 sqm each and refixing of shutters in same opening of any descrption after easing and adjusting, repairing, tightening the joints of frame of shutter complete all as specified and directed

Taking down shutters of any description n.exc 1 sqm each and refixing of shutters in same opening of any descrption after easing and adjusting, repairing, tightening the joints of frame of shutter complete all as specified and directed

Taking down chowkhats or frames of any description with shutters (without taking off shutter from the frames) not exceeding 1.5 Sq.m each.

Taking down chowkhats or frames of any description with shutters (without taking off shutter from the frames) exe 1.5 Sqm but not exceeding 4.0 Sq.m each.

S & F Second class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints.

S&F 1.25 mm thick pressed steel frame for doors with one or more rebated including necessary fixing lungs, hinges, lock, strike plates etc complete all as specified and size of frame 105 x60 mm

S&F 1.25 mm thick pressed steel frame for doors with one or more rebated including necessary fixing lungs, hinges, lock, strike plates etc complete all as specified and size of frame 125 x60 mm

S & F 30 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., divided into squares with plain, chamfered or rounded mitred and rebated sash bars any numbers, edges of framing plain, chamferesd or rounded, fitted with cut and mitred beads for securing glass etc., for windows and ventilators, etc are provided with stiles and rails as specified in SSR Pt I Section 8, clause 8.24 (b)

S & F 35 mm thick second class hard wood, plain framed , panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers supplied and fixed to chowkhats.

S & F 35 mm thick second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars) chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in SSR Pt I Section 8, clause 8.24 (a)

S & F for Aluminium anodized barrel tower bolt of 12 mm dia and 300 mm length of extruded section .(ISI Marked). Complete all as specified and directed by Engineer in Charge .

S & F for Aluminium anodized barrel tower bolt of 12 mm dia and 150 mm length of extruded section .(ISI Marked). Complete all as specified and directed by Engineer in Charge .

S & F for Aluminium handles,cast type, anodised 150 mm long, all as specified and directed.

S & F for stainlees steel sliding door bolt, of size 300mm, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections of cast aluminium alloy.

S & f for Floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor over all length of cover plate 150 mm.

S&F 300 mm , MS ordinary rat tail rod pattern springs including roller and plate , door spring fixed to door shutter complete

S&F stainless steel non magnetic curtain rod 25 mm dia& 1.20mm thick with fixing brackets and decorative type brass knobs both side of each rod.

S&F Stainless steel (AISI 316 Grade) peg set of 5/6 pegs, 250-300 mm length of plate, complete all as specified and directed.

S & F for Stainless steel wire cloth of size 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanized wire staples, fixed in repairs.

S & F for Stainless steel wire cloth of size 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanized wire staples.

S & F Stainless steel kitchen plate rack 0.80mm thick sheet of over all size 31" x 30" x 10" fixed with steel screws and steel rawal plugs Complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames glazed with putty or fixed with beads or from metal frames including punching or drilling out old glazing pins /spring clips and providing and fixing new one.

S & F for Glazing with plain sheet glass, ordinary quality, 4 mm thick and glazing with oil putty or aluminium or PVC beading in squares not exceeding 0.5 Sq.m in each pane.

Preparation of New wood and wood based surfaces of any description not otherwise described over 10 cms width or girth and applying 2 coats of synthetic enamel paint over a coat of pink primer.

M&L preparation of old painted wooden surfaces of any descripton over 10cm width or girth and applying one coat of synthetic enamel paint First quality all as specified and directed .

Preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer.

Preparation of old or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer.

Dismantling and taking down U/S point wiring of any type (light, fan, socket, power) complete fitting such as switches, ceiling roses, pendants, lamp holder, light fitting etc including CI/Pressed steel terminals, switch box, and making good the disturbed surface of wall/floor etc, to match with the existing surfaces of wall/floor complete all as specified and directed. Note :- If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding.

Material & Labour for Point Wiring for one light Point/one fan point/ one call bell point, controlled by one switch with 1100 volts grade single core conforming to (IS:694 /1990) PVC insulated unsheathed 1.5 sqmm multi stranded copper conductor cable (FRLSH) with continious earth wire of 1.5 Sqmm stranded copper conductor cable (FRLSH) PVC insulated unsheathed , drawn in and including concealed PVC conduit,medium grade(ISImarked) ,duly concealed on wall/ceiling or above false ceiling with fittings not less than 20 mm dia medium grade (Color coding of wires shall be Phase, neutral and earth wire all as specified ) sunk Metal flush box with and incl decorative polycarbonate frame for housing Modular Switches, sockets , fan regulators etc including white cover plate complete all as specified and directed. Note:- i) Cost of cutting chases of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted rates ii) If the contractor fail to make good the disturbed surface of wall/ceiling etc and do not match with the existing surface of wall/ceiling to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding.

(a) One light point controlled by one no of one way switch

(b) One ceiling fan point controlled by one no of one way switch

(c) One Exhaust fan point controlled by one no of one way switch

(d ) One 5 pin 5/6 Amp socket outlet point on independent board controlled by one no of one way switch single pole 5/6 amps.

(e) One 3 pin socket outlet 5 amps on the same board with other switches, with cables 1.5 sqmm size

All as per item No -2 above but with 2.5 Sqmm PVC insulated FRLSH cable for 15 Amps power point complete all as specified & directed.

S & F switch Modular single pole, one way 6 Amps , 1 module, 230 volts, 50 hz complete all as specified and directed by Engr-in-Charge.Make: Legrand cat No: 6734 01/ Indoasian Cat No: 800000 or equivalent make of L&T/Havells

Supply and fixing switch modular , one-way 16Amps, 1 module 240 Volts AC complete all as specified and directed by Engr-in-Charge. Make: Legrand cat No: 673411/ Indoasian Cat No: 800002 or equivalent make of L&T/Havells

Supply and fix Modular Socket outlet, 6A - 2/3 pin combined, 2 module ISI marked, 230 volts, 50 hz complete all as specified and directed by Engr-in-Charge.Make: Legrand cat No: 6734 52 / Indoasian cat no: 800020 or equivalent make of L&T/Havells

Supply and fixing modular socket, 6A/16A -2/3 pin combined 2 module 230 volts, 50 hz complete all as specified and directed by Engr-in-Charge.Make: Legrand cat No: 6734 55 / Indoasian cat no: 800022 or equivalent make of L&T/Havells

Supply and fixing ceiling rose surface bakelite 65/25 mm dia having three terminals complete all as specified & directed.

S&F LED tube light batten 20 watts 4 fts polycarbonate housing, translucent diffuser with LED light source , 2200 lumen, natural white ,surge protection range 2KV, voltage protection range 120-280 VAC , 2 years warranty ,system efficacy not less than 110 Lm/watt for the fitting , power factor>0.95 total harmonic distortation<20% , colour rendering index >80, coefficient colour temp 6500 K, fixed on site with all accessories all as specified and directed. Make Shakti cat part No SZSLBMX020 or equivalent in Havells , wipro or bajaj LM79 and LM80 reports to be produced . BIS certification must .

Supply and fix LED street/security light fitting 20W housing made out of pressure die-cast aluminium alloy with toughned glass, IP-66 protection, working on 240 Volts AC, 50 HZ, consisting of reflective lens wired with approximate driver PF>0.98 having over voltage protection upto 440 volts, Surge protection level > 10 KV, thermal short circuit protection THD < 10% made up of long life LED chips (SMD) in modular with Ra>70, and LED lumen efficiency >140 lumen per watt, beam angle along the drive way, 120 degree, beam angle across the drive way, 80 degree luminior efficiency > 120 Lumens/watt power LED should be of more than 01 watt CCT should be between 5700 K- 6500 K including fixed on wall with 02 Nos MS clamp made out of 40 x 6 mm F1 and bracket made out of 40 mm dia light grade GI pipe not less than 1.0 mtr long bend to shape with use reducer for inner dia 38 mm for fix with inside light fitting including connecting with 1.5 sq mm, 3 core, PVC insulated Copper conductor cable 1100 Volta grade all as specified and as directed by Engr-in-Charge Make : shakti Cat Part No : SZPCLPM020/ ENDURAPEARLSL20W of HEVELLS/eauivalant Model in Bajaj/CROMPTON. Note :- (i) the firm has to give warranty for street light fittings including driver minimum for 03 years for any defects developed during the period. (ii) The contractor shall submit the third party LM 79 & LM 80 report from any NABL approved laboratory. (iii) The fitting should have BIS, CRS (iv) Connection to luminaire shall be done in suitable PVC connector within the bracket/luminaire end and are inclusive in above.

Supply & fix energy efficient ceiling fan with BLDC motor and blades, 1200 mm sweep, Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with operating voltage of 140 to 285 V, with metallic finish , accessories / remote toggle switches pre wired and connected through PVC connector complete all as specified and directed. Make: Havells/Atomberg/bajaj

S&F Exhaust fan AC single phase 230/240 Volt of size 300 mm sweep, metallic body powder coated painted finish, Power consumption- 50 W, Air deplacement -1290 Cum/Hr, RPM-900 complete with louvers including making whole and grouting of nut bolts etc and making good the disturbed sufaces of wall complete all as specified and directed. Make - Orient/Bajaj/Havells/Crompton

Supply and fixing sheet metal enclosure double door type for MCBs DB TPN 415V AC 4 way with 200 Amps rated bus bar complete all as specified and directed .Make- legrand / ABB/ Schnider/L&T/Siemens

S & F Double door sheet metal enclosure for DB, 8 way, SPN with 200 Amps rated bus bar, 240 Volts, ISI marked, 50 Hz suitable for housing MCBs and making good for distrubed surface with existing etc complete all as specified and directed.

S &F 415 V, 10 KA, 'B' curve minature circuit breaker (MCB) of TPN 20-32 amps fixing on MCB DB complete with connecting testing and complete use copper ferruel for connect cable through MCBs all as specified and directed by Engr-in-Charge.

S &F 230 V, 10 KA, 'C' curve minature circuit breaker (MCB) of SPN 10-32 amps fixing on MCB DB complete with connecting testing and complete use copper ferruel for connect cable through MCBs all as specified and directed by Engr-in-Charge.

Supply and fixing 10 KA 'B' curve miniature, circuit breaker (MCB) of single pole and current carrying capacity 5 to 32 AMP ISI marked, 230/240 volts, 50 Hz in the MCB DB Complete with connection testing and commissioning all as specified and directed by Engr-in-Charge.Make: Hager/L & T/ Havells

Supply and fixing 240 V, 10 KA 'C' curve miniature circuit breaker (MCB) of single pole and current carrying capacity 0.5 -4 Amps, in the MCB DB complete with connection testing and commissioniing.

M &L for sub main wiring with two run of 4 Sqmm (nominal cross sectional area) of single core unsheathed PVC insulated cables 1100 Volts grade multi stranded copper conductor drawn through & including non metallic rigid PVC conduit of size 19/20 mm or higher dia with & including necessary conduit accessories concealed/surface nly on roof & colomn) type including 4.0 Sqmm stranded copper conductor PVC insulated cable as earth wire connected to common earth dolly complete all as specified & directed

Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. ( earth pit not less than 2.25 mtr depth below ground level at any type of strata ) with top edge of the earth plate not less than 1.5mtr below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15cm all around the plate. connected by 4 mm GI wire as earth lead by means of brass nuts and bolt, thimbles check nuts, washers including concrete chamber of PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM 1:4 funnel with wire mesh, RCC pit cover of 320x320x80mm size (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI wire upto 7.5 mtrs long with 15 mm dia light grade GI pipe protection and watering pipe of GI 20 mm bore, medium grade, including all exavation and earth work and connecting the earthing wire to panel, including testing on completion complete all as specified and directed by Engr-in-charge. Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick rainforced with XPM weighing not less than 4kg/sqm in lieu of CI cover. (ii) Cost of additional GI wire more than 7.5 mtrs will be measured and paid seperately under relevant items.

complete all as specified and directed by Engr-in-charge. Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick rainforced with XPM weighing not less than 4kg/sqm in lieu of CI cover. (ii) Cost of additional GI wire more than 7.5 mtrs will be measured and paid seperately under relevant items.

Material and labour for fixing or passing through pipe, laid in trenches, fixed on wall, LT panel board, XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of size 16 sqmm 2 core with required aluminium cable lugs, lugs should properly crimp with crimpping tools, heat shrink joints, Colour code heat shrink sleeves at both cable ends , cable gland for cable safety when passing through panel holes, including laying cable route indicators of suitable size RCC or steel type as per site requirement all as specified and directed. by Engr-in-charge. Note:(i)GI tubing required shall be measured and paid separately under relevant item of sch as supply only,

Taking down old unserviceable service/UG cable of any size from building

Excavation in trenches for taking out/laying of cable and pipe line not exceeding 1.5 mtr deep and not exceeding 1.5 mtr wide in soft/loose soil. complete all as specified and directed.

Returning, filling including spreading levelling watering and well ramming in layers not exceeding 25 cm thick in each layer in any type of soil.complete all as specified and directed.

Removing excavated material to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above starting point. complete all as specified and directed.

M&L for fine dry sand cushioning for underground cable by providing layers of sand 8 cm before laying and 15 cm deep after laying the cable including streching the cable (measurement to be taken after punning down consolidated thickness). complete all as specified and directed.

M & L for cable protection bricks common burnt clay sub class 'B' designation 75 for protection of UG cable laid in trenches all as specified and directed at site complete all as specified and directed.

M&L for road cutting and making good with PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) of minium size 150mm X 100mm in respect of width and thickness complete all as specified and directed.

Supply, laying & joined Galvanised Tubing 50 mm bore, light grade as in sleeving etc laid in trenches/pole post/under culvert/under road etc for cable protection complete all as specified and directed. Make:Jindal/Indian Tubes Co.

TARUN ENGINEERING WORKS