Annual Plan-PR.NO. 616/25-26-New drinking water project near Aiswarya Anganvadi in ward 17

construction of bore well

OD436954/2025-2026:Drilling 150 mm dia DTH bore well vertically suitable to accommodate well pipe of 180 mm dia PVC Pipe 6 kg/ cm2 for various depth up to150 m below ground level, having over burden 20 m or more in all classes of soil and rock inclusive of hire charge for machinery and all other accessories and stores putting up temporary sheds, conveying , lowering the casing pipe,jointing with coupling , developing and flushing continuously for 3 hours testing the discharge, , lowering dummy of the proposed Submersible motor pump set in the drilled bore well assuring the free movement of the same ceiling the casing pipe in the rock with cement grout, providing temporary cap if necessary as per the direction of departmental officers, including cost of fuel ,oil and other stores and all items incidental to the completion of work, including conveyance of casing pipe,coupling and dummy etc. but excluding the cost of casing pipe and specials etc. complete

OD436951/2025-2026:Supplying and fixing 180mm dia PVC pipe 6kg/cm2 (casing pipe)

OD436957/2025-2026:Supplying 180mm PVC well cap

OD436950/2025-2026:Water quality test charges

OD436956/2025-2026:Charges for Yield test

OD447396/2025-2026: Supplying and erection of electrically driven best quality reputed makeISI marked , open well/bore well submerssible pump set having bronze impeller stainless steel shaft capable of discharging required lpm against a total required head including all accessories such aspanel board, main wsitch, suitable starter , suitable size of flat submerssible cable, wiring materials delivery pipe for open wellelectrification charges etc.complete.The warranty shall be for a minimum period of two years including all fittings. (delivery pipe up to 10m cable , foot valve, , panel board, with main switch , fuses,ELCB, starter, earthpipe etc. (As per KWA /HO/SP/333/2011/pumps/ tvm dated 20.12.2011)A-1 HP .Details for 1HP

OD447403/2025-2026:Supplying and fixing 63 mm dia UPVC column pipe incuding all cost and conveyance Material

OD447404/2025-2026:Supply and providing good quality garware make nylon marine rope 16 mm size with required PVC tie-bad ad tieing the pump set with required outside the well

OD447405/2025-2026:Supplying and fixing4mm 3 core cable including all cost and conveyance

Pump House

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

50.6.2.1:Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15cm in: CM 1:6 ( 1 cement :6 coarse sand) etc complete

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.43.1:Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.1.3:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

10.5.2:Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.Using flats 30x6 mm for diagonal braces and central cross piece

13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work