WD/2025-26/3T-1/915

Renovation of Three no Faculty rooms in the Department of Rural Development Studies, K.U.

Page No-203 Item no - 1 Removing loose scales blisters etc from old painted surface and throughly smoothening the surface to make the same suitable for receiving fresh coat of paint

Page No-201 Item no - 4 Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) : (Two coats) ii) Luxary quality

Page No-195 Item no - 7-a-i Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (In Ground Floor) a) two coat. i) Water based interior grade Acrylic primer.

Page- 303 Item- 3 Labour for taking out almirah, wood shelves for tiling work and reshifting this

Page-152 Item no-31 Taking out shutter of door and window, dismantling by parts (for repair or replacement of damaged parts), reassembling and refitting and rehanging same with old fittings but with new screws as necessary. (Where different parts of same shutter are renewed under different item, payment under item 73 will be made once only).

Page-69 Item no-41 Supplying and laying true to line and level Double Charge Vitrified Tiles of approved brand conforming to IS 15622: 2006 (Group B I a) and tested as per IS 13630:2006 (relevant parts) [Non-modular sizes for tiles with Water Absorption (av.) ≤ 0.08 %] in floor, skirting etc. using polymerised adhesive of 6mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course and joints grouted with admixture of white epoxy grout materials of approved brand including spacer -2mm as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials,Iabour and all other incidental charges complete as per direction of Engineerin-Charge.(Note: This work should not be executed without specific permission of Superintending Engineer) (a) ln Ground FIoor:(size not Iess than 600mmX 600 mm X 9.5 mm thick)

Page 200 Item 1-b Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc

Page - 200 Item no-2-A-a Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : b) On wooden surface. iv) Two Coats.

Page 200 Item 1-a (a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc

Page - 200 Item no-2-A-2 Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary On steel or other metak surface with super gloss (hi gloss ) b)Two coat ( with any shade except white )

Page- 143 Item- 23 Hydraulic door closer of approved quality as per ISI standerd fiited and fixed complete - Medium ISI size 2

Supplying fitting fixing vanishing blind curtain (Local Market Rate)

Page 204 Item No=5-b Rendering the surface of walls and ceiling with white cement based wall putty of approved make and brand ( 1.5 mm thick)

Page 16 Item No=16 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor. (II)In Gr. Floor level

Page 189 Item 1 Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] i) With 1:6 cement mortar b) 20mm thick plaster

Page-303 Item 5 Carpentar for Door cutting for looking space

Page-147 Item 38-a Supplying wooden moulding slanting beat of size 37mm X 18mm (finished) of approved design to finish the joint between wooden frame of door/window with masonary in true line and level fitted & fixed with adhesive and head less pins complete as per direction of Engineer -in-charge. a) Teak wood beat