SPECIAL REPAIRS TO BUILDING NO P 42E AT NAVAL DOCKYARD VISAKHAPATNAM UNDER GE I DM VISAKHAPATNAM

Amount

[SCHEDULE 'A' PART-I [B/R WORKS]

Demoliton brick work or stone masonry built in cement mortar including all quoins, arches , pillars etc and removing the debries to a distance 5km away from the Dockyard premises all as specified and directed.

M&L for pre cast cement concrete type 1:3:6 type C-1 (20mm graded stone aggregate) block masonry with solid blocks exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for rubbish off the ND (V) complete all as specified and directed.

M&L for providing, cement concrete type B1 1:2:4 (Using 20mm graded stone aggregate) as in floors concrete and kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work rubbish off the ND (V) complete all as specified and directed.

M&L for Ready Mix concrete Design Mix M-35 as in foundation, including raft footings, foundation beams, plinth beams, bases for column etc., basement slabs, underreamed piles and mass concrete complete all as specified and directed.

M&L for form work to sides of concrete foundations, footings, bases of rough finishes surfaces of concrete columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate 100mm thick as in sub base for floors, hard standings etc complete all as specified and directed.

M&L for hardcore of gauge not exc. 63 mm, deposited, spread and levelled in layers not exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for Mild Steel TMT bars but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for light shade vitrified ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for coloured non skid ceramic tiles 7mm to 8mm thick (square or rectangular) of area exc 0.18 but n.exc 0.38 Sq.m in floor set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and directed.

M & L for coloured glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:3 on fair faces of brick work or concrete surfaces as in backing coat to skirting complete all as specified and directed.

Taking down cement plaster on walls/ceiling etc including racking out joints hacking for key, scrubbing down with water complete all as specified and directed.

M&L rendering 10 mm thick in CM (1:6) on fair faces of brick work or concrete surfaces and finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of distemper oil emulsion over a coat of primer with 3mm thick wall care putty on wall complete all as specified and directed.

M&L rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surfaces and finishing the surface even and smooth without using extra cement complete all as specified and directed.

Material & labour for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets all as specified and directed.

S&F anodised aluminium snap grid frame work of size 605x605mm using main and cross tee of size 15mm x 15mm 1.5mm ( weight not less than 0.12 kg / Rm) and wall angle of size 40mm x 25mm x 2mm ( weight not less than 0.36 kg / Rm) in ceiling with hanger 6mm dia GI (up to 1200mm length) adjusting level fixed to roof slab by means of ceilng cleats made out of GI flat 40x 3mm size 60mm long and expansion hold fastners 12.5mm dia 40mm long complete , including cover fillets complete all as specified and directed.

M&L for PVC insulation panels with EPS stuck to 1mm plain PVC sheet suitably placed in false ceiling grid made of Aluminium/G.I./M.S. as per specification and drawing complete all ass pecfied and directed.

Taking down chowkats or frames exc 1.5 Sqm but not exc 4 Sqm each (Without taking off shutters from the frame) complete all as specified and directed.

All as per item No. 1.25 above, but not exc 1.5 Sqm each

S&F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides and both face is covered with decorative face veneer with lipping/frame to match complete all as specified and directed.

M&L for preparation of new wooden surfaces and applying two coat of synthetic enamel paint over one coat of pink primer over 10 cm width or girth complete all as specified and directed.

Forming jambs etc, to opening in brick masonry, including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work complete new work, built in cement mortar 1:6 complete all as specified and directed.

M&L for PCC 1:3:6 type C1 usig 20mm graded crushed aggregates as in anchoring hold fast bed plates etc complete all as specified and directed.

S&F stainless steel hinges 100mm long, medium weight, cold rolled and fixed to wooden or steel framed complete all as specified and directed.

S&F 150mm stainless steel barrel tower bolt of extruded section complete all as specified and directed.

S&F 125mm stainless steel handles, medium weight, cold rolled and fixed to wooden or steel framed complete all as specified and directed.

S&F 250mm stainless steel sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts complete all as specified and directed.

M&L powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

M&L powder coated Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed.

M&L for sheet glass 4.8mm thick, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane complete all as specified and directed

M&L for 9mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

S&F aluminium extruded type body Door closer hydraulically regulated, Designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and directed.

M&L for Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S&F 150mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor all as specified and directed.

Providing and fixing factory made UPVC white colour sliding window exceeding 2.00 Sqm .Three tack made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mmx52mm), sliding sash (42mmx67mm). Sliding mesh sash (42mmx57mm) sliding interlock (One vertical length in each shutters) (45.5mmx28mm, Glzing bead (24.5mmx16mm) will be mitred cut and fusionwelded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware. EPDM gasket, 1.2+, -0.2mm thick galvanised steel frame (30mmx18mm) 2 Nos, sliding sash (30mmx18mm), sliding mesh sash(26mmx10mm) profile to be inserted in required profile,frame will be fixed to the wall with 8 mmx100mm long fasteners, Hardware (touch lock of zinc alloyed (white powder coated), steel roller system. Stainlesssteel wire cloth 0.36mm nominal dia of wire and average width of aprature 1.40mm and required accessories.Note :- The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose) including taking down existing one complete.

S&F anodised aluminium decorative grill (anodised transperent or dyed to require shade according to IS 1868 with minimum anodic coaing of grade AC -15) of approved design / pattern , with approved standered scetion and fixed to the existing window frame with CP brass /stainless steel screw @200 mm ceneter to center , including cutting the gril to propre opening size for fixig and operation of hanmdles and fixing approvedanodised aluminum stanedre scetion around the openings , all comete as per requirement and direction of Engr-in- Charge.

S&F 4.00mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S&F in repairs venatian Roller blinds type 100mm wide including hanging arrangement made up of anodised aluminium channel with acrylic mechanism with bottom weight type vista leveler all as per manufacturers instructions and as directed by engg in charge including taking down the worn out venetian blinds complete all as specified and directed.

S&F Providing and fixing Powder coated aluminium (minimum) thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and complete all as specified and directed.

S&F 5.50mm sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane complete all as specified and directed.

S&F 12mm thick Prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thicknes in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed.

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking plat forms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admix ture of pigment to match with shade of granite including round edging and marking anti skid cutting lines with cutters on treads, complete all as specified and directed.

M&L for 75mm thick in cement concrete type C2 1:3:6 (Using 40mm graded stone aggregate) as in plinth protection finished even and smooth with out using extra cement complete all as specified and directed.

M&L for forming construction joints 30mm deep and 10mm wide, filled with sealing compound grade 'A' complete all as specified and directed.

M&L for chipping & removal of existing damaged, cracked, spalled & loose portion of concrete of the RCC members (20mm to 50mm thick) completely till the reinforcement is exposed and sound concrete is observed by using mechanical means and manual chisels and further the surface is jetted with clean water for removal of dust and loose particles complete all as specified and directed.

M&L for preparation of exposed surafces of rusted steel reinforcement with metal wire brush,cleaning the rusted surfaces free from loose rust and applying rust remover cum passivator (Sika Rustoff 100 @ 0.20Kg / Sqm or any other equivalent approved make of E -in -C's branch) on surface of existing reinforcement with brush to the rusted reinforcement, removing rust with flex after 24 hours of application of rust remover with the help of wire brush, sand paper and throughly washed with water with the help of pressure jet and allowing surfaces of steel it to dry complete all as specified and directed. Note:- Area of cleaned reinforcement steel bar shall only be considered for payment.

M&L for preparation of surfaces or steel of reinforcement by cleaning throughly and providing , mixing and applying zinc anti-rust agent as per manufacturers method of application to rebar corrosion protection system to reinforcement ( Sika / Fosroc/BASF/ Dr sunanda) @3.75Kg/Sqm surface of steel reinforcement in two coats complete all as specified and directed.

M&L for applying a coat of Polymer modified cementious bonding coat on the concrete surfaces with one part of Styrene Butadiene Rubber latex emulsion (SBR latex) manufactured by M/s Fosroc chemicals or equivalent chemicals manufactured by Sika India Pvt Ltd / Choksey Chemicals Pvt. Lt with four parts of water and six parts of cement by weight. Coverage of SBR latex-0.25Ltr / sqm for one coat complete all as specified and directed.

M&L for applying polymer modified, cementitious mortar fibre reinforced, single component shrinkage controlled, (Renderoc SP40 of Fosroc Make or equivalent in Sika / Choksey) having a compressive strength of 40 MPA strength for reparing of RCC members like columns, Beams / Slab soffits etc. complete all as specified and directed.

M&L for application of polymer modified reinstatement mortar 20mm thick in isolated places of repair works of RCC members with Rendroc S2 of M/s Fosroc make or equivalent in Sika / Choksey having a compressive strength of M40 grade complete all as specified and directed.

Taking down GI tubing 15mm dia with all connection all as specified and directed.

Taking down GI tubing 20mm dia with all connection all as specified and directed.

S&F 15mm bore Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and directed.

S&F20mm bore Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and directed.

Cutting chases, pinning in stone, concrete block or slab wall, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth in brick walls complete all as specified and directed.

S & F in repair Vitreous China Ware Wash hand basin white, flat back, size 550 x 400 mm size (flat back or angle back type) in repairs including cutting for and pinning ends of brackets or erecting stand complete all as specified and directed.

M&L for 32mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

Supply fix in repairs Viterous China wash down water closet pan (pedestal pattern), white and trap, including connection to drain(or outgoing pipe) and to flushing pipe, anti-syphonage pipe etc, complete all as specified and directed.

S&F in repairs vitreous us china squatting pan `ORISSA` pattern size 580 x 440 mm with integral foot rests including connection to trap and to flushing pipe, anti-syphonage pipe and provision of concrete bedding complete making good floor all as specified and directed.

S&F in repairs of Vitreous China bowl urinal flat back size 465x355x265mm white (minimum) (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe all as specified and directed.

S&F in repairs urinal spreader of chromium plated push type with PVC pipe of 15mm bore as required complete all as specified and directed.

S & F in repairs Vitrous China urinal partition white of size 310 x 700mm complete all as specified and directed.

S&F in repairs brass chromium plated shower rose 125 mm size with or without swivel joints any size including fixing to steel pipe or union complete all as specified and directed.

S&F plastic water closet seat cover, white closed pattern with flat bottom and cover and mild steel C.P or aluminium hinging device all as specified and directed.

S&F PVC low level flushing cistern 10 ltrs capacity including all fittings and brackets bends flush pipe etc and fixed in repairs complete all as specified and directed.

S/F in repair PVC connection (high density) 15 mm dia 600 mm with PTMT nuts both ends with rubber washer all as specified and directed.

S & F for 1000 ltr capacity rotational moulded polye thylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling water tanks exc 500ltr but n exc 1000 ltr and removing to store complete all as specified and directed.

S & F in repairs Fancy type chromium plated 15 mm bore Stop valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S & F in repairs 15 mm bore pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S&F in repair 15 mm bore dia of pipe Bib taps, fancy type chromium plated, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S & F 25 mm dia Gun Metal, globe or Gate Valve with Iron wheel head Screwed both ends for Iron Pipe and fixed in repairs all as specified and directed.

S&F in repair 75mm bore PVC (SWR) soil, waste and vent pipes single socketed in any legth with rubber ring joints fixed to walls complete all as specfied and directed

S & F in repair 110 mm bore PVC (SWR) , waste and rain water pipes single socketed in any length with rubber ring joints complete all as specified and directed.

S & F in repair 75 mm bore PVC (SWR) bends of any radius all as specified and directed.

S & F in repair 110 mm bore PVC (SWR) bends of any radius all as specified and directed.

M & L for 75 mm bore PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed.

S & F in repair 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal With access door all as specified and directed.

S&F in repair Waste pipes 32 mm dia LDPE ,UPVC pipes of pressure rating 6 Kg/cm2 for wash basins and urinals all as specified and directed.

S&F in repairs grating round of size 75mm dia, chromium plate complete all as specified and directed.

S&F in repair health faucet chromium plated with CP pipe of 1.4m long with jet spray with PVC chord and connector complete all as specified and directed.

S&F in repair wall mounted stainless steel (gde 304) toilet paper holder with flap of weight not less 300 gms complete all as specified and directed.

S & F in repair soap dish vitreous china white of size 160x160x90 mm fixed to plug with chromium plated brass screw complete all as specified and directed.

S&F in repair chromium plated tubular towel rail D Type of 20mm dia bore and 600mm long comlete all as specified and directed.

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F 110mm bore PVC SWR 'P' trap complete all as specified and directed.

S&F 110mm bore PVC SWR 'S' trap complete all as specified and directed.

S&F Powder coated Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed.

S&F 5.0mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed.

[SCHEDULE 'A' PART-II [E/M WORKS]

Taking down old unsv copper /aluminium point wiring (light, fan.socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc removing materials to store for keeping or for taking credit (credit for above items should be made as per conditions separately ) and making good disturbed surfaces of walls,floors etc.., directed.

Taking down old unserviceable DB's and main switches along with MCB's and MCCB's all as specified and directed.

M&L for concealed point wiring with 1.5 sq mm (nominal area), PVC insulated, stranded single core unsheathed FRLS copper conductor cable drawn through with PVC conduit medium grade with all fittings and accessories of PVC conduit/ casing caping (like Tee, bend etc) complete fixed to walls etc with and including 1.5 sqmm (nominal area) PVC insulated stranded single core unsheathed FRLS copper cable as earth continity wire connecting to common earth point including supply & fixing of galvanized pressed mild steel Modular terminal boxes of suitable size as require for fixing modular switch socket regulator etc. complete all as specified and directed including necessary chase cutting for conduits to walls, floors and sinking boxes and making good to walls, floors complete all as specified and directed.

One light point controlled by one 5 Amps switch one way

One fan point controlled by one 5 Amps switch one way

One 3/5 pin 5 Amp switch socket outlet on independent board

One 3/5 pin 5 Amp socket outlet on same board.

Supply & fix modular type switch 6 Amp oneway single module all as specified and directed.

S&F modular socket outlet 2 in 1,3 pin 5 Amp all as specified and directed.

S&F modular coverplate with support plate for 3 and above modules with anodised metal boxes all as specified and directed.

S&F modular coverplate with support plate for 8 and above modules with anodised metal boxes all as specified and directed.

M&L for concealed point wiring with 2.5 sq mm (nominal area), PVC insulated, stranded single core unsheathed FRLS copper conductor cable drawn through with PVC conduit medium grade with all fittings and accessories of PVC conduit / casing caping (like Tee, bend etc) complete fixed to walls etc with and including 2.5 sqmm (nominal area) PVC insulated stranded single core unsheathed FRLS copper cable as earth continity wire connecting to common earth point including supply & fixing of galvanized pressed mild steel Modular terminal boxes of suitable size as require for 3/5 pin socket outlet 15 Amps complete all as specified and directed including necessary chase cutting for conduits to walls, floors and sinking boxes and making good to walls, floors complete all as specified and directed.

S&F 6/15 Amps modular switch socket combination 3 module all as specified and directed.

S&F fan step regulator, 120W - 2 module complete all as specified and directed

S&F ceiling rose,3 phase /PVC/polycarbonate, isolated body all as specified and directed.

Supply & fix LED recessed full open 2 x 2 feet with highly efficient light smoothy optics to deliver superior illuminous and energy saving of 36 watts complete all as directed.

Supply and fixing LED lights fitting 1 x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

S&F SP MCB 6 to 32 Amps C Curve complete all as specified and directed.

S&F TPN MCB 63 Amps C Curve complete all as specified and directed.

S&F TP MCB 63 Amps C Curve complete all as specified and directed.

S&F SPN MCB 32 Amps C Curve complete all as specified and directed.

S&F concealled vertical MCB distribution board suitable for MCCB incomer 125A, IP 43 protection, Double door, metal enclosure, TPN, 415 Volts, 8 way incl dismantling taking down unsv one all as specified and directed.

S&F MCCB, 25KA, 3 pole, with thermal magnetic trip unit, rated current 160amps complete with spider link incl dismentling taking down unsv one all as specified and directed (Suitable for MCCB incomer DB).

S&F doubledoor TPN DB 4 way double door with 200 amp rated bus bar all as specified and directed.

S&F SPN DB 8 Way double door with 200 amp rated bus bar all as specified and directed.

M & L for concealled type sub main wiring with 2 runs of 6 sqmm FRLS grade PVC insulated copper conductor wire single core multistrand for phase & neutral, 6 sqmm FRLS grade PVC insulated copper conductor wire for earth continuity drawn in and including non metallic FRLS ISI marked PVC conduit medium grade dia with conduit accessories , including necessary chase cutting for conduits to walls, floors and sinking boxes and making good to walls, floors complete all as specified and directed by Engr-in-Charge. Note:Cutting chases for DB &making good to wall shall be inclusive of quoted rate

M & L for wiring with 2 runs of 10 sqmm FRLS grade PVC insulated copper conductor wire single core multistrand for phase & neutral, 10 sqmm FRLS grade PVC insulated copper conductor wire for earch continuity drawn in and including non metallic FRLS ISI marked PVC conduit medium grade dia with conduit accessories including necessary chase cutting for conduits to walls, floors and sinking boxes and making good to walls, floors complete all as specified and directed by Engr-in-Charge. Note:Cutting chases for DB &making good to wall shall be inclusive of quoted rate

M & L for wiring with 4 runs of 10 sqmm FRLS grade PVC insulated copper conductor wire single core multistrand for phase & neutral, 2 runs of 10sqmm FRLS grade PVC insulated copper conductor wire for earch continuity drawn in and including non metallic FRLS ISI marked PVC conduit (heavy grade) with conduit accessories including necessary chase cutting for conduits to walls, floors and sinking boxes and making good to walls, floors complete all as specified and directed by Engr-in-Charge. Note : Cutting chases for DB &making good to wall shall be inclusive of quoted rate

M & L for wiring with 4 runs of 16 sqmm FRLS grade PVC insulated copper conductor wire single core multistrand for phase & neutral, 2 runs of 16 sqmm FRLS grade PVC insulated copper conductor wire for earch continuity drawn in and including non metallic FRLS ISI marked PVC conduit (heavy grade) with conduit accessories including necessary chase cutting for conduits to walls, floors and sinking boxes and making good to walls, floors complete all as specified and directed. Note:Cutting chases for DB &making good to wall shall be inclusive of quoted rate

S&F metal plug and socket board with MCB single pole 20 amps, 16KA incl dismantling taking down unserviceable one all as specified and as directed.

Supply and fix LED building security light 70W IP 66 rated including supply and fixing with 40mm dia medium grade GI pipe bracket 1.5 mtr long bent to shape, mounted on pole/wall with suitable clamps nuts and bolts and all accessories complete including connection with 3 core PVC insulated sheathed flexible cable with multistranded copper conductor cable from ceiling rose to fitting terminal including taking down old unsv one all as specified and directed

Material and labour for removing out split type AC upto 2.0 tonne capacity and to install at same location after civil work & electrical work and fixing including making necessary opening for suction and discharge and drain pipe line, brazing copper pipes after grouting of outdoor/indoor unit and making necessary electrical connection, recharging , testing and commissioning all as specified and directed. Note for item Nos. 2.31 & 2.32 :- (i) Before removing the split AC, operational status of split AC to be submitted to JE E/M and split AC to be made opertational to the same level as it was before removing. (ii) Copper pipe for suction and drain to be taken out carefully and stored at safe place, if any damage occurs, replacement cost to be borne by the Contractor.

M&L for disconnecting & taking down old burnt exhaust fan of any sweep and S&F wall mounted exhaust fan AC single phase 230/240V of size 450mm along with its louvers, shutters complete all as specified and directed. Make :- Havells/Orient/Atomberg Note :- Taking down the old exhaust fan & submit to AGE E/M store after dismantling all included.

M&L for disconnecting & taking down old burnt air circulator fan of any sweep and S&F air circulator fan 230V single phase oscillating of size 450mm suitable for wall mounting complete all as specified and directed. Make :- Havells/Orient/Atomberg Note :- Taking down the old air circulator fan & submit to AGE E/M store after dismantling all included.

M&L for disconnecting & taking down old ceiling fan of any sweep and S&F ceiling fans 230V, 1200mm sweep with electronic type regulator and accessories complete all as specified and directed. Make :- Havells/Orient/Atomberg Note :- Taking down the old ceiling fan & submit to AGE E/M store after dismantling all included.

Supply and fix AC stand as per existing AC Model and mounting the out door unit of the split AC or window AC all as specified and directed.

S&F LED tube light fitting with LED tube, 2'long, 10 watt, CDL, 230 Volts , complete with all accssories internally pre wired incl dismantling taking down unsv FTL/CFL fiitings all as specified and directed.

S&F LED engagement light Red & Green including dismantling taking down unserviceable one all as specified and directed.

S&F bell electric AC 240 volt, 50 Hz all as specified and as directed.

S&F bell push piano type one way 5Amp, 240 volt all as specified and as directed

M&L earthing with galvanised steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground earth pit not less than 2.25 m deep below ground level with top edge of the plate not less than 1.5 m below normal ground level connected to GI wire 4 mm by means of nuts, bolts check nuts, washers of galvanised iron or steel connected to earth test point including excavation work in any strata with precasted pcc chamber with precasted PCC cover slab with GI protection pipe 40 mm dia light gde upto 7.5 mtr/20 mm dia tunnel pipe med grade but all as specified and directed.

SOWRYA CONSTRUCTIONS (BID ID -3502378)

sai ganesh enterprises (BID ID -3501311)

SATYAMEGHA ENGINEERS (BID ID -3506256)

venkata sai constructions (BID ID -3508709)

SRI SIMHADRI COMPANY (BID ID -3506622)

MURALI KRISHNA ASSOCIATES (BID ID -3502435)

RAGHU RAMA PANDA (BID ID -3507863)

SSVR PROJECTS & INFRASTRUCTURE (BID ID -3508554)

P SRINIVASA RAO (BID ID -3508299)

UNITY PROJEKTZ (BID ID -3508288)