Alappuzha District Panchayath Punnapra divn Punnapra thekku GP ward 5 Parappil padamConstruction of Motortharashed

Amount

Motorshed and parakkuzhy

OD3719/2023-2024:Ring bund type1 putting up ringbund as per approved shape 2.5m bottomwidth,1m top width using empty gunny/polythene bags filled with earth placed in 2 rows at 0.6 m apart and filled in between with puddle clay to form bund for an average height 2m including labour dismantling the bund after completion of the work etc

50.2.3.1:Pumping or Bailing out water and removing slush etc by using pump set including cost of labour, oil hire charges of pumpset, etc complete

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

OD3720/2023-2024:Modified old data 60.64.1 Coconut Plie- Supply and stacking well matured straightcoconut post for driving down through various strata bellow bed level including cost conveyance labour charges etc complete

OD3721/2023-2024:Modified old 60.64.4 Coconut Pile -Driving down coconut pile lines and levels through various strata including all hire charges and labour for fixing ,staging platform and all other appliances necessary for pile drivingdown afterpointing the bottom end

4.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

OD3722/2023-2024:Modified old 60.7.2 DR PACKING under foundation -dry stone packing under foundation with good quality blasted rubble including conveyance of material and labour charges etc complete as per direction of department officers at site .

OD3723/2023-2024:DRY RUBBLE MASONRY -Dry rubble witout concrete levelling course masonry with good quality blasted rubble including packing to compactness to line and level cost and conveyance of all material ,labourcharge etc complete as per directions of departmental officers at site ( boat load upto 3 KM)

4.1.5:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

5.1.3:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

10.2:Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

50.6.2.1:Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15cm in: CM 1:6 ( 1 cement :6 coarse sand) etc complete

50.10.1:Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

13.4.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 coarse sand)

12.50:Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

12.51.1:Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05%) total coated thickness, zinc coating 120 grams per sqm as per IS:mm(+0.05%) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws complete:Ridges plain (500-600 mm)

13.37.1:White washing with lime to give an even shade:New work (three or more coats)

50.9.15.2:Supplying and fixing 300 mm Aluminium aldrop

OD3844/2023-2024:FIlling with red earth (excluding rock) in trenches,plinth,sides of foundation etc in layers not exceeding 20cm in depth,consolidating each deposited layer by ramming and watering,lead upto 50m and liftupto 1.5m as per direction of site Engineer-in-charge

Bidder Name

BAIJU V