PROVN OF COVERED SHED FOR 06 X VEHS AND 02 X STN STORES (EQPT STORE) AND OTHER LBW/SPL REP WORKS AT NAA UNDER GE (N) TEZPUR

Amount

Note 1: (Applicable for all parts/items) : The biidders/contractors are advised to read tender document, all drawings & all corrigendum/amendments and general condition of contracts before entry/quoting the rates. Note 2:- Attention to bidder is hereby invited to upload revised BOQ if published during their bid submission. Uploading of incorrect/ pre-revised BOQ shall be treated as non bonafide and rejected. Fixed credit has been given in technical documents which shall be taken into account during acceptance of bid/tender.

Dismantling mild steel sheets (corrugated, semicorrugated, plain etc. of any type) in roof coverings, walls, ridges etc. or of similar types complete in all respect as specified and directed.

Taking down cement plaster on brick/stone/concrete surfaces of wall, ceiling etc. or of similar type, including raking out joints, hacking for key & scrubbing down with water complete in all respect as specified and directed.

Taking down chowkats and shutters (without taking off shutters from the frame) exc 1.5Sqm and not exc. 4Sqm each complete in all respect as specified and directed.

Dismantling of timber scanttlings of size 40 Sqcm & over in section, in any position for framed work complete in all respect as specified and directed.

Surface dressing not exceeding 15cm deep in soft/loose soil including necessary tools and plants complete in all respect as specified and directed.

Excavation in trenches in soft/loose soil, not exceeding 1.50m wide and not exceeding 1.50m in depth for foundations, man holes or similar items etc. and getting out, complete in all respect as specified and directed.

Labour only for returning and filling in layers not exceeding 25cm thick and well ramming including watering as required (Note: Excavated soil as retreived against excavation item to be used) complete in all respect as specified and directed.

Labour only soil filling under floors or in foundations including watering and consolidation not exceeding 25cm thick and well ramming including watering as required (Note: Excavated soil as retreived against excavation item to be used) complete in all respect as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete in all respect as specified and directed.

Providing and laying cement concrete in foundations, filling and mass concrete using 1:4:8 nominal mix type D-2 (using 40mm nominal size crushed and graded stone aggregate) complete in all respect as specifified and directed.

Providing and laying for reinforced cement concrete type B-1, 1:2:4 (using 20mm nominal size crushed and graded stone aggregate) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; complete in all respect as specifified and directed.

Providing and laying for reinforced cement concrete type B-1, 1:2:4 (using 20mm nominal size crushed and graded stone aggregate) in columns, posts, struts etc. complete in all respect as specifified and directed.

Providing and laying for reinforced cement concrete type B-1, 1:2:4 (using 20mm nominal size crushed and graded stone aggregate) in sun-shade, chajja, cantilever section or similar type etc. complete in all respect as specifified and directed.

Providing and laying cement concrete 1:2:4 type B-1 (using 20mm nominal size crushed and graded stone aggregate) in beams, lintels or of similar types complete in all respect as specified and directed.

Providing pre-cast reinforced cement concrete cover etc. in cement concrete 1:2:4 type B-1 (using 20mm nominal size crushed and graded stone aggregate) or of similar type of work including necessary form work complete in all respect as specified and directed.

M & L PCC (1:2:4) type B-1 using 20 mm nominal size crushed and graded stone aggregate in coping, hold fasts or of similar items including necessary cutting, form work etc.cement complete in all respect as specified and directed.

M & L for 75mm thick PCC (1:3:6) type C2 (using 40mm crushed and graded stone aggregate) as in plinth protection and finished surface even and smooth without using extra cement including necessary expansion joints and filling with bituminious compound in it, complete in all respect as specifified and directed.

M & L for 75mm thick PCC (1:3:6) type C2 (using 40mm crushed and graded stone aggregate) as in sub base/lean concrete and finished the surface fair and even complete in all respect as specifified and directed.

M & L for 100mm thick PCC (1:3:6) type C2 (using 40mm crushed and graded stone aggregate) as in sub base/lean concreten and finished the surface fair and even complete in all respect as specifified and directed.

Material and labour for 40mm thick PCC (1:2:4) type B1 (using 20mm nominal size, crushed and graded stone aggregate) as in hardstanding/flooring, finished the surface even and smooth without using extra cement complete in all respect as specifified and directed.

Providing and laying 40mm thick damp proof course to horizontal or vertical surfaces including necessary formwork using type B-0, 1:2:4 concrete (using 12.5mm nominal size crushed and graded stone aggregate) mixed with water proofing compound complete in all respect as specifified and directed. (Water proofing compound shall be measured & paid separately under supply only item)

Supply only liquid water proofing compound complete in all respect as specified and directed.

M & L for cement concrete Type C-2, 1:3:6 (using 40mm nominal size crushed and graded stone aggregate) in foundations filling and mass concrete as in manhole etc. complete in all respect as specified and directed.

M&L for PCC 1:2:4 type B 1 (using 20mm nominal size crushed and graded stone aggregate) as in surface channels & drains complete in all respect as specified and directed.

M & L for brick work with old size sub-class 'B' bricks, class designation 75, straight or curved on plan exc. 6 mtr mean radius built in cement mortar 1:6 complete in all respect as specifified and directed.

M & L for half brick work with old size sub-class 'B' bricks, class designation 75, built in cement mortar 1:4 complete in all respect as specifified and directed.

M & L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter in rough finished flat concrete surface complete in all respect as specifified and directed.

M & L for formwork to sides of pillars, posts, struts, piers, columns and stanchions of square/rectangular in shape and in rough finished concrete surface complete in all respect as specifified and directed.

M & L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping or in similar work in rough finished flat surface of concrete complete in all respect as specifified and directed.

Material and labour for preparation of newly undecorated plastered surface of wall and applying three coats of cement based paint over one coat of alkali resistant primer paint including filling of voids/surface with wall care putty on plastered surface complete in all respect as specified and directed.

S & F coloured 0.50mm thick pre-painted galvalume aluminium zinc coating, GI based trapezoid profile mild steel sheet, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws with bitumen washer to truss members of any material complete in all respect as specifified and directed.

S & F coloured pre-painted galvalume aluminium zinc coating GI based mild steel sheet 0.50mm thick having tensile strength of 550 Mpa as in ridge or valley gutter or of similar type used in roofs fixed with self tapping screws with bitumen washers complete in all respect as specified and directed.

S & F colour pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick having tensile strength of 550 Mpa as in eves covering or of similar type, fixed with self tapping screws with bitumen washers complete in all respect as specified and directed.

S & F 10mm dia and over TMT bar cut to length bent to shape required, including cranking, bending spiarlly for hooping for colums, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete in all respect as specified and directed.

S & F upto 10mm dia TMT bar cut to length bent to shape required, including cranking, bending spiarlly for hooping for colums, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips for stirrups, spacers and binders complete in all respect as specified and directed.

S & F mild steel sections (Beam, hollow sections, tee, angle, channel or flat sections) in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing, independent fixing with welding etc. including distance pieces, cleats etc. using Fe 410-W (Gde E-250) quality A complete in all respect as specifified and directed.

Supply and Fix exposed GI powder coated snap grid frame work for false ceiling in flat or in sloping, of grid size 600x600mm comprising of wall/cleat angle of size 25x25x0.35mm and cross tee of size 24x38x0.70mm with minimum 2mm dia GI wire as suspender and including 4mm thick decorative, pre -painted non asbestos board (E-Board) in false ceiling including fixing arrangement from steel/wooden truss of any type complete in all respect as specifified and directed.

S & F Plate girder or single stanchions, built up of one beam or channel section with flange plates, caps, bases, splices, angle brackets, cleats and other connections using Fe 410 -W (GdeE- 250) quality A complete in all respect as specified and directed.

S & F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment using Fe 410 -W (GdeE- 250) quality A complete in all respect as specified and directed.

S & F Mild steel screw bolts (purpose made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, of 12 to 20mm dia and , length of bolt n. exc 30cm long complete in all respect as specified and directed.

S & F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290, Gde-E-165 using square bars complete in all respect as specified and directed.

M & L for mild steel iron frame for door , window using joist, channel, angle, tee, tubes, flat sections, fixed independently, without connecting plates, etc. conforming to Fe. 290., Gde-E-165 complete in all respect as specifified and directed.

S & F 1.25 mm thick, mild steel, plain, black sheet in wall cladding, steel door/gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up,complete in all respect as specified and directed.

S & F steel windows with side hung shutters including projecting type hinges, steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete in all respect as specifified and directed.

S & F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete in all respect as specifified and directed.

M & L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. in flat position of rough finished complete in all respect as specified and directed.

M & L for glazed ceramic coloured wall tiles of size area exc. 0.09Sqm and not exc. 0.16Sqm set and jointed in neat cement slurry and pointed with white cement with pigment to match the tile colour including 15mm thick screed bedding in cement mortar 1:4 complete in all respect as specified and directed.

M & L for ceramic coloured digital printed floor tiles of size area exc. 0.09Sqm and not exc 0.16Sqm set and jointed in neat cement slurry and pointed with white cement with pigment to match the tile colour including 15mm thick screed bedding in cement mortar 1:6 complete in all respect as specified and directed.

M & L for rendering/plastering 15 mm thick in cement mortar 1:4 on faces of brick or concrete surfaces and finished the surface even and smooth without using extra cement complete in all respect as specifified and directed.

M & L for rendering/plastering 15 mm thick in cement mortar 1:6 on faces of brick or concrete surfaces and finished the surface even and smooth without using extra cement complete in all respect as specifified and directed.

M & L for preparation of old decorated plastered or unplastered surface of wall and apply two coats of white wash complete in all respect as specified and directed.

M & L for preparation of new unplastered surface of wall and apply two coats of white wash complete in all respect as specified and directed.

S & F 35mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass gauge etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass/gauze etc.; sizes of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a), complete in all respect as specified and directed.

S & F stainless steel wire cloth, 0.32 mm nominal dia of wire and average width aperture 1.80 mm and fixed with stainless steel wire staples fixing with beads etc., complete in all respect as specified and directed.

Supplied and fixed in openings, solid PVC door frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube, as per specification & drawing complete in all respect as specified and directed.

Supplied and fixed factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of mild steel tubes for top & bottom rails. mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete in all respect as specified and directed.

Supplied and fixed 10 liter capacity, PVC valveless, syphonic action type, low level cistern, capacity, white, with inlet ball valve, float and handle including brackets & flush pipe of polyethylene complete in all respect as specified and directed.

S & F 15mm bore GI tubes medium grade, galvanised with all fittings fixed complete to walls and ceiling or laid in floors including necessary cutting chauging in concealed nature complete in all respect as specified and directed

S & F 20mm bore GI tubes medium grade, galvanished with all fittings fixed complete to walls and ceiling or laid in floors including necessary cutting chauging in concealed nature complete in all respect as specified and directed

S & F PVC (SWR) nahani trap of 75mm outlet dia fixed with PVC 150X150mm size openable at center grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

Supply and fixed 75mm size of butt hinges stainless steel complete in all respect as specified and directed.

Supply and fixed 100mm size of butt hinges, mild steel medium weight complete in all respect as specified and directed.

Supplied and fixed Aluminium handle cast type anodised 125 mm size complete in all respect as specified and directed.

Supplied and fixed Aluminium anodised, barrel tower bolts of extruded section and fixed 200mm complete in all respect as specified and directed.

M & L for hardcore of broken stone or boulders of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding watered and rammed to a true surface using broken stone or boulders complete in all respect as specifified and directed.

Material and labour for river bed fine sand filling under floor or below paver blocks incl. watering and consolidation complete in all respect as specified and directed.

S & F 38mmX1.5mm thick PVC dividing strips, for flooring complete in all respect as specified and directed.

Providing and laying 20-22mm thick machine cut kota stone slab flooring/treads etc. over 15mm thick cement screed base in cement mortar 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete in all respect as specifified and directed.

Providing and laying 20-22mm thick machine cut kota stone slab in skirting/dado/riser etc. over 15mm thick cement screed base in cement mortar 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete in all respect as specifified and directed.

Providing and laying heavy duty non-skid coloured floor tiles of size 0.09 Sqm/0.16Sqm set and jointed in neat cement slurry and pointed with white cement with pigment to match the tile colour over including 15mm thick screed bedding in CM 1:6 complete in all respect as specified and directed. Make: Somany (Heavy duty), Johnson (Endura), Bell Orient

Supply and fixed PTMT ball valve high pressure 20mm bore dia with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe complete in all respect as specified and directed. Make: Prayag, Symet, Shakti

Supply and fixed three layered white in colour rotational moulded water storage tanks of capacity 1000 ltr (cylindrical vertical with closed top) including two tank nipples of 20mm dia, hoisted and fixed in position complete in all respect as specified and directed. Make:- Sheetal (Virat),Supreme (Siltank), Sintex, Oriplast

Supplied and fixed aluminium anodised sliding door bolts with hasp and staple (bolt type) 12mm dia bolt 250mm long complete in all respect as specified and directed.

M & L for painting two coats with synthetic enamel paint on new un-decorated wooden surface over 10cm width or girth, including one coat of pink primer & preparation of surface complete in all respect as specified and directed.

Material and labour for preparation of new un-decorated steel surface of any description not otherwise described, and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete in all respect as specified and directed.

M & L for three coats white wash over new plastered surface of wall including necessary preparation of surface complete in all respect as specified and directed.

Supply and fixed 15mm bore, cast ABS body, CP finish, shower rose of size 100 mm dia and shower arm of cast copper alloy CP finished, fixed to iron pipe/fiitings complete in all respect as specified and directed.

S & F vitreous china urinal flat back large of size 37.5X39X59cm white, including CP finish cast copper alloy waste coupling, urinal spreader fixing arrangement to walls, PVC waste pipe etc. complete in all respect as specified and directed. Make: Hindware Cat No. 60002 (urinal), or equivalent make of Cera, Perryware

S & F 20mm dia bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete in all respect as specified and directed.

S & F PVC (SWR) bends any radius 75mm bore complete in all respect as specified and directed.

S & F PVC (SWR) bends any radius 110mm bore complete in all respect as specified and directed.

S & F PVC (SWR) junction single, (single T) equal or unequal 110mm bore pipe with access door complete in all respect as specified and directed.

S & F PVC (SWR) junction single, (single T) equal or unequal 75mm bore pipe with access door complete in all respect as specified and directed.

S & F PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches 75mm bore complete in all respect as specified and directed.

S & F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed over wall 75mm bore including necessary pipe clamps complete in all respect as specified and directed.

S & F PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches 110mm bore complete in all respect as specified and directed.

S & F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed over wall 110mm bore including necessary pipe clamps complete in all respect as specified and directed.

S & F PVC (SWR) 110mm internal bore cowl complete in all respect as specified and directed.

S & F PVC (SWR) 75mm internal bore cowl complete in all respect as specified and directed.

S & F steel ventilator with top hung shutter including hinges, steel peg stay complete in all respect as specified and directed.

S & F for 4mm thick sheet glass ordinary quality and glazing with oil putty in square complete in all respect as specified and directed.

S & F for 4mm thick frosted sheet glass ordinary quality and glazing with oil putty in square complete in all respect as specified and directed.

S & F for 5.5mm thick black tinted sheet glass ordinary quality and glazing with oil putty in square complete in all respect as specified and directed.

Supply and fixed Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with brass chromium plated bracket guard and railing 60cm long complete in all respect as specified and directed. Make- Prayag, Cera, Hindware, Jaquar

S & F Bib taps of 15mm bore, fancy type CP finish cast copper alloy with crutch handle screwed down for iron pipes complete all as specified and directed.

Material and labour for preparation of newly plastered surface of walls and applying two coat of weather coat over 2mm thick wall care putty and a coat of primer including rubbing and all necessary preperation complete in all respect as specified and directed.

Material & labour for preparation of newly undecorated plastered surface of wall and applying two coats of oil bound distemper including one coat finished with spunge roller over a coat of alkali resistant priming paint over 2mm thick (in two layers), wall care putty complete in all respect as specifified and directed.

Supply and fixed 15 mm bore male/female threaded fancy type CP finished angle valves, cast copper alloy, screwed down, high pressure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions including CP finish cup washer/wall flange complete in all respect as specified and directed. (Note:- if small piece of pipe required for connection with fittings beyond socket/elbow etc. CP finish copper alloy exten nipple will be used without any extra cost)

S & F Wash hand basins, vitreous China of size 550 x400mm(flat back or angle back type), including cutting for and pinning in ends of brackets over new angle iron erecting stand embedded in PCC (1:2:4) block including 32mm dia bore waste fitings cast copper alloy chromium plated with long screwed shanks and flynuts flange and beded in redlead cement, PVC waste pipe including 15mm bore dia fancy type CP finish Pillar tap, cast copper alloy with capstan heads, screwed down high presuure, with or without lettered hot or cold with long screwed shanks and fly nuts, screwed for iron pipes complete all as specified and directed.

Supply and fixed vitreous china wash down water closet Pan (pedastal pattern) white including plastic water closet seat, white, closed pattern with flat bottom, new CI/UPVC 'P' or 'S' type trap and mild steel chromium plated hinging device (exclusive flushing cistern and flush pipe) complete in all respect as specified and directed.

Supply and fixed toilet paper holder of cast copper alloy chromium plated fixed to walls with chromium plated (CP) brass screws complete in all respect as specified and directed. Make:- Jaquar Cat Part No. AEC-1151, Hindware, Cat Part No. F450027 or equivalent make in Cera

S & F Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats complete in all respect as specified and directed. Make: Prayag, Shakti, Hindware, Cera

Material and labour for any colour of granite stone 17-19mm thick, as in floor, dado, steps, laid over and including screed bed 15mm thick in cement mortar (1:6), jointed and pointed with white cement mixed with pigment to match the shade of stone including cutting, rubbing and polishing surface, including cutting for wash hand basin, sink, gas pipe hole etc., to the entire satisfaction of the Engineer-in-Charge complete in all respect as specified and directed.

Providing and laying coloured, glazed, pre coated chequered cement concrete tiles of any shape and size, 20-25mm thick with grey cement and pigment,; set jointed and pointed in neat cement slurry with pigment to match the colour of tile, in flooring including over 15mm thick screed bed in cement mortar 1:4 complete in all respect as specified and directed.

M & L for writing letters or figures (block roman, Italic or Indian) using synthetic enamel paintof 30cm high over byuilding on square or round base painting complete in all respect as specified and directed.

S & F tubular towel rail, 20mm dia, D type, 60cm long between flanges cast copper alloy, CP finished complete in all respect as specified and directed.

M & L for Septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, brick work in CM 1:4 in Walls , RCC M15 in Base Slab , Baffle walls and Roof Slab including beams etc with Vent shaft , manhole openings with cover connection etc., complete with effective depth of 1.5 meter and overall depth of 3 meter for Septic Tank 50 users complete in all respect as specified and directed. Ref Drg No.TD/SZ/504 Sheet No 1/1

Material & labour for 1.2m dia and 3m effective depth Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size complete in all respect as specified and directed. Ref Drg No. TD/SZ/502 Sheet No 1/1

M & L for 150mm bore pipe for concrete bed in PCC 1:4:8 type D 2 using 40mm nominal size crushed and graded stone aggregate to drain pipes including packing under and completely surrounding pipes with concrete after they are laid and tested in complete in all respect as specified and directed.

M & L for 150mm internal dia of Salt-glazed stoneware drain pipes laid in trenches and jointed complete in all respect as specified and directed.

M & L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mitred/stopped ends etc. .complete in all respect as specified and directed.

S & F 5mm thick Solid PVC Wall Lining consisting of wood grain printed colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing and dismatalling of existing complete all as specified and directed.

S & F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing

S&F 2nd class Hard wood scanttlings, wrought in any position for framed work jointing wirh nails, screws, nut bolt etc. including necessary supports to existing truss complete in all respect as specified and directed.

S & F second class hard wood plain fillets. square, rectangular or triangular in section, clean sawn, secured with nails or brads of size size exc 13Sqcm but n. exc 25Sqcm complete in all respect as specified and directed.

S & F anodized aluminium sliding windows shutters without sash bars, aluminium sections weighing (side and top section not less than @ 0.634Kg/m, bottom @ 0.606 Kg/m, locking section @ 0.734 Kg/m) including necessary jointing cleats, galzing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings like locking arrangments and suitable handles for sliding purpose, 4mm thick plain glass and stainless steel wire mesh of dia 0.36mm and average width of aperature 1.40mm, wheels etc. including three track 2mm thick anodized aluminium frame complete in all respect as specified and directed.

Supply and fixed 12mm thick toughned glass door including edge grinding and polishing, holes for door handle, dedicating hinges two nos( SS premium patch fittings, fixed in wall/wooden post, floor door hydraulic floor spring to bear upto 1200mm wide and 2100mm, 12mm thick glass door, stainless steel handle (two Nos), one SS patch lock arrangement for glass door with necessary fittings and fixtures complete in all respect as specified and directed. (Make of fitting OZONE, HETTICH, AXIS INTERNATIONAL, BRICON ENGLAND)

S & F PVC connections 15mm size with PTMT nuts of length 4500mm complete in all respect as specified and directed.

E/M PORTION

Material and labour for point wiring with 1.5 Sqmm PVC insulated FRLSH unsheathed multi stranded copper conductor cable 1100 Volts grade single core conforming to IS-694-1990 and one run of continous earth wire with 1.50 Sqmm stranded core PVC insulated unsheathed copper conductor cable draw in & including PVC surface casing ‘N’ capping not less than 20mm wide double lock type to be fixed with the help of rawal plugs & screws including necessary fittings & fixtures and including PVC terminal box and PVC board making good disturbed surface with CM (1:4) to match with the existing surface for the following:-

(a) One light/fan/exhaust fan point controlled by one, one way switch, with cable 1.5 sqmm.

(b) All as per item No. 121 here-in- before but for 3 pin 5 Amps switch socket combination on independent board with 1.5 sq mm copper cable.

(c) All as per item No. 121 here-in- before but for 3 pin 15 Amps switch socket combination on independent board with 4.0 sq mm copper cable.

M&L for switch piano (flush button type) single pole, one way, 5 Amps.

M&L for switch socket out let 2 in one, 5 Amps, 240 Volts flush type, all as specified.

M&L for switch socket combination 2 in One , 6 pin 5 Amps & 15 Amps flush type, universal.

Supply and fix in replacement of lamp holder, PVC/Polycarbonate type for bracket fittings complete all as specified.

S&F ceiling rose surface backelite Polycarbonate type two to three terminals.

M&L for sheet metal enclosure for DBs SPN 8 way with rated bus bar, 240 V, Double door, complete flush mounted all as specified and as directed.

M&L for MCB single pole 240 volts 5 to 32 Amps.B Curve

M&L for MCB single pole & neutral 240 volts 32 Amps.

Supply and fix LED BALL LAMP of 10W with lumen output not less than 900 lm and colour temp 6500K complete all as specified and directed.

Supply and fixing LED luminaires, 20 watts, lumen output not lessthan 2000 (4 feet), made of anodised extruded aluminium housng, wit high transmissivity diffuser, high lumen output, with suitable electronic driver, and operated in single phase, 230 volts, 50HZ, all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable of size 23/0.0076, from conector and ceiling rose, complete all as specified and directed.

Supply & Fix LED wall security lights 15W with necessary brackets (made out of 25mm bore GI pipe light grade appx 0.6 meter long bend to shape) nuts, bolts, etc fixed on walls complete all as specified and directed.

Supply & fix non decorative ceiling fans 1200 mm sweep, 230 V, BEE 5 star rated complete and accessories including fan hooks complete all as specified and directed.

Supply and fix 300mm sweep 900 RPM, with metal blade and louver complete fixed in wall with fastener and including making hole in wall of suitable size and plastering finishing of surfaces complete all as specifed .

M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6mm thick buried directly in ground (earth pit not less than 2.25 metre below ground level) with top edge of the earth plate not less than 1.5 metre below ground level, connected to GI earth wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of SSR Part I connected to earth test point all as specified or indicated including excavation and connected earth work, in soft/loose soil, removing soil upto 50m, PCC 1:3:6 type C1 as in pit, 20mm dia GI pipe medium grade for watering pipe, 40mm bore GI medium grade earth lead protection pipe, 50mm thick RCC 1:2:4 type B1 cover slab of earth pit reinforced with 8 mm dia TMT Bars @ 10cm C/C both ways and with handle made out of 20mm dia bars, funnel, strainer, alternate layer of charcoal dust and common salt and testing on completion , complete all as specified and directed.

Supply and fix in repairs 380mm sweep 1400 RPM, with metal blade and louver complete fixed in wall with fastener and including making hole in wall of suitable size and plastering finishing of surfaces complete all as specifed

Excavation in trenches, in soft / loose soil not exceeding 1.5m wide and not exceeding 1.5m in depth loose soil and getting out for removing/laying of cable complete all as specified and directed.

Returning, filling in excavated soil, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick all as complete all as specified and directed.

Removing of surplus excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed

Material and labour for sand cushioning with a layer of sand 80mm thick before laying of cable and 150mm thick after laying of cable in trenches for protection of cables complete all as specified and directed.

Material & Labour for sub class 'B' bricks laid flat in trenches for the protection of under ground cable complete all as specified and in SSR Part-1

Supply & fixing GI Pipe light grade 40 mm dia, ISI marked, of required length for protection of cables complete including necessary MS clamps, nuts, bolts and washers etc fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Supply, laying, jointing and testing LT cable in trenches or on poles / walls, XLPE Insulated screened, PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sqmm 2 core for laying in trenches and poles /walls complete all as specified and directed.

Supply & fixing GI Pipe Medium grade 25 mm dia, ISI marked, complete with all fittings fixed complete to walls, ceilings, floors laid in trenches complete all as specified and directed.

Supply and fixing Gun metal Gate Valve with iron wheel head, screwed both ends for iron pipe and fixed of size 25mm , ISI Marked , complete with all fitting accessories complete as specified and directed

Cutting and insertion of Tee/ ferrule for taking branch connection complete all as specified and directed.

M/S Inder SINGH SABARWALL

Anil Kumar Sarmah

D G Corporation

MD. LATIFUL AHMED HUSSAIN

M/S S.K. Sharma

M/S M N ENTERPRISE

M/S Deep-Jeet