Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹16.0 LAccepted-AOC | ₹16.0 L | L1 | Accepted-AOC Agreement Executed |
| 2 | L2₹16.0 LRejected-AOC | ₹16.0 L | L2 | Rejected-AOC L2 |
| Sl No | Description | Qty | Unit | LAIJU.P.VARGHESE L2 | BINCE GEORGE L1 |
|---|---|---|---|---|---|
| 1.00Pump set new rate | |||||
| 1.00 | OD165239/2024-2025:Supply of pump:-
Supply of KWA pre- qualified reputed make slow speed, split case Centrifugal pump with bronze/SS impeller, SS shaft and CI pump casing with suitable type base plate with coupling, coupling guard foundation bolt & nuts etc.complete suitable for coupling the pump and motor above the base plate etc. complete.
The duty condition as follows. Discharge -9.5LPS
Total head -125 mtrs Suction head - 4 mtrs
Length of suction pipe- 4 mtr | 1 | no | 6,65,000 ₹6.7 L | 5,70,000 ₹5.7 L |
| 1.00 | OD165238/2024-2025:Supply of KWA prequalified reputed make horizontal solid shaft foot mounted TEFC squirrel cage induction motor suitable for the above pump working 3 phase 50 Hz. AC supply, working voltage 415 V (suitable for the pumpset). The motor shall confirm to IE2/IE3 as per IS12615- 2018 digital motor protection relay shall be included in starter as per present CEA regulations 2010. Flexible coupling shall be used for coupling of pump and motors" 4 poles(1440rpm) | 1 | no | 50,000 ₹50,000 | 35,734 ₹35,734 |
| 1.00 | OD165233/2024-2025:Supply suitable rating (Fully automatic ATS starter with air break contact for less than 50 HP and for above 50 HP FCMA starters to be used) starter suitable for the above motor with over voltage and under voltage protection, single phase preventer, over load relay with motor protection relay with main contactor and bypass contactor as per IE rules and code of practice etc. Complete" | 1 | no | 65,000 ₹65,000 | 25,000 ₹25,000 |
| 1.00 | OD165230/2024-2025:Capacitor:-
Supply, erection, testing and commissioning heavy duty APP capacitor for the motor to get a power factor above 0.95. The capacitor shall confirm to IS 2834. " | 1 | no | 12,500 ₹12,500 | 30,000 ₹30,000 |
| 1.00 | OD165236/2024-2025:1)Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of
2.7 metre long etc. with charcoal/ coke and salt as required .
2)Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)-10metre | 1 | no | 18,000 ₹18,000 | 18,000 ₹18,000 |
| 1.01 | OD165234/2024-2025:Suction and delivery pipe connections :-
Supply and fitting of suitable size best quality CI/DI pipe . Suitable for the above pump set and suitable size foot valve and connecting the suction pipe and valve with suitable flanges, nut and bolts, IR sheet etc. complete with bypass arrangements, supply and fitting pressure guage of suitable rating with main cock and connecting the delivery side of the pump with the valves and suitable specials to connect with the pumping main. If the dia. of suction pipe is above 200 mm CI/DI pipes & specials shall be provided " | 1 | no | 22,000 ₹22,000 | 16,000 ₹16,000 |
| 1.01 | OD165231/2024-2025:Valves:-
Supply of suitable size best quality heavy duty ISI marked CI double flanged sluice valve and Non return valve with suitable pressure rating. Fitting of valves shall include proper RCC support especially for Non return valves. In case of positive suction pump sets sluice valve should be in suction as well as delivery sides for easy repair works. " | 1 | no | 16,000 ₹16,000 | 15,000 ₹15,000 |
| 1.01 | OD165235/2024-2025:Cabling work:-
Supply, laying, testing and commissioning of suitable size 3 core XLPE Alluminium cables for the above pump set from bus bar to panel board , panel board to starter and from starter to motor considering energy conservation." | 10 | metre | 2,000 ₹20,000 | 820 ₹8,200 |
| 1.01 | OD165232/2024-2025:Panel board (suitable for operating two pump sets but one pumps set at a time):-
Supply, erection, testing and commissioning of cubical type floor mounted MS fabricated dust and vermin proof common control panel board consisting of 1 no. suitable capacity MCCB as incomer and 2 Nos. of suitable capacity MCCB as outgoing, (the 2 MCCBs are interlocking with each other) providing suitable size Aluminium bus bar, inter connect the above MCCBs and fitted with 3 Nos. of indicator lamps, 1 no Volt meter with selector switch, 1 no Ammeter with selector switch etc. complete and provided with a common earth bus for the entire panel and inter connect with the MCCBs as per IE rules and code of practice. The panel shall be fitted on a common base frame on suitable foundation & quot; | 1 | no | 35,000 ₹35,000 | 60,000 ₹60,000 |
Tender Value
₹17.0 L
EMD Value
₹42,472
Closing Date
17 Oct 2025, 3:00 pmClosed
ExecutiveEngineer
ExecutiveEngineer PHDivisionMuvattupuzha
DEPOSIT Palakkuzha GP RWSS Palakkuzha Arakkuzha Supply installation commissioning of 9.5 LPS centrifugal pumpset 126m head with DI pumping line to Illikunnu Chelappuzha tanks and allied works
2025_KWA_807525_1
09/2025-26/EE/PHDN/MVPA
Open Tender
Civil Works - Water Works
Palakkuzha Panchayath
Please refer Tender documents.
8 documents required · 8 mandatory
₹2,760
₹42,472
24 Jan 2026
9 Oct 2025
21 Oct 2025
9 Oct 2025
17 Oct 2025
9 Oct 2025
Amount
Pump set new rate
OD165239/2024-2025:Supply of pump:- Supply of KWA pre- qualified reputed make slow speed, split case Centrifugal pump with bronze/SS impeller, SS shaft and CI pump casing with suitable type base plate with coupling, coupling guard foundation bolt & nuts etc.complete suitable for coupling the pump and motor above the base plate etc. complete. The duty condition as follows. Discharge -9.5LPS Total head -125 mtrs Suction head - 4 mtrs Length of suction pipe- 4 mtr
OD165238/2024-2025:Supply of KWA prequalified reputed make horizontal solid shaft foot mounted TEFC squirrel cage induction motor suitable for the above pump working 3 phase 50 Hz. AC supply, working voltage 415 V (suitable for the pumpset). The motor shall confirm to IE2/IE3 as per IS12615- 2018 digital motor protection relay shall be included in starter as per present CEA regulations 2010. Flexible coupling shall be used for coupling of pump and motors" 4 poles(1440rpm)
OD165233/2024-2025:Supply suitable rating (Fully automatic ATS starter with air break contact for less than 50 HP and for above 50 HP FCMA starters to be used) starter suitable for the above motor with over voltage and under voltage protection, single phase preventer, over load relay with motor protection relay with main contactor and bypass contactor as per IE rules and code of practice etc. Complete"
OD165230/2024-2025:Capacitor:- Supply, erection, testing and commissioning heavy duty APP capacitor for the motor to get a power factor above 0.95. The capacitor shall confirm to IS 2834. "
OD165236/2024-2025:1)Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required . 2)Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)-10metre
OD165234/2024-2025:Suction and delivery pipe connections :- Supply and fitting of suitable size best quality CI/DI pipe . Suitable for the above pump set and suitable size foot valve and connecting the suction pipe and valve with suitable flanges, nut and bolts, IR sheet etc. complete with bypass arrangements, supply and fitting pressure guage of suitable rating with main cock and connecting the delivery side of the pump with the valves and suitable specials to connect with the pumping main. If the dia. of suction pipe is above 200 mm CI/DI pipes & specials shall be provided "
OD165231/2024-2025:Valves:- Supply of suitable size best quality heavy duty ISI marked CI double flanged sluice valve and Non return valve with suitable pressure rating. Fitting of valves shall include proper RCC support especially for Non return valves. In case of positive suction pump sets sluice valve should be in suction as well as delivery sides for easy repair works. "
OD165235/2024-2025:Cabling work:- Supply, laying, testing and commissioning of suitable size 3 core XLPE Alluminium cables for the above pump set from bus bar to panel board , panel board to starter and from starter to motor considering energy conservation."
OD165237/2024-2025:Erection, testing and commissioning :- Erection of pump ,motor, starter on suitable concrete foundation with base, plate, coupling the motor and pump using flexible coupling, fitting coupling guard, trial run and commissioning "
Pumping Line interconnection work to 15KL OH tank at ILLIKKUNNU
100.1.1:Excavating trenches of required width for pipes, cables, etc., including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering, etc., and disposing of surplus excavated soil as directed, within a lead of 50m, in all kinds of soil.
100.59.1:Cutting the bituminous / concrete roads with cutting machine for a minimum depth of 200mm along the sides of proposed alignment of the pipe to be laid without causing any damage to other utilities, including the charges for hire and conveyance of tools and plant, cost of consumables and charges for lighting, watching, ribbon fencing, caution boards, traffic diversion, and as per the direction of departmental officers etc. complete, before carrying out the demolition of bituminous / concrete road by mechanical means and carrying out the excavation.
100.14.1:Conveying and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS: 8329 excluding cost of pipes and specials: 100mm diameter Ductile Iron Class K-9 Pipes.
18.70.1:Providing push - on-joints to Centrifugally (Spun) Cast Iron Pipes or Ductile Iron Pipes including testing of joints and including the cost of rubber gasket:100 mm dia pipes
OD139271/2025-2026:Labour for cutting and grinding DI pipe with steel saw
18.68.1:Providing and laying D.I specials of class K - 12 suitable for push - on jointing as per IS : 9523 :Upt 600 mm dia
OD140242/2025-2026:Conveying and fixing G.I. pipes complete with G.I. fittings excluding trenching and refilling etc., but excluding cost of pipes and fittings for External work: 100mm diameter nominal bore.
100.31.1.2:Conveying and fixing C.I. sluice valves (with cap) by providing bolts, nuts, rubber insertions etc., complete, but excluding the cost of the valve (tail pieces, if required, will be paid separately): 100mm diameter, Class I.
100.32.1:Conveying and fixing C. I. Single Acting Air Valve of approved quality with bolts, nuts, rubber insertions etc., complete, but excluding the cost of air valve (tail pieces, if required, will be paid separately): 25mm Single Acting Air Valve.
OD148074/2025-2026:construction of valve chamber of inner size 1.1m X1 .1mx 1.1m in M 25 grade cement concrete for reinforced cement concrete work and 10mm TMT steel rod (Fe 500 or above) (330Kg) for foundation, side wall and cover slab platform 1.6mx1.6mx0.2M, side wall 20cm thick, in 1:3:6 using 20mm broken stone, plastering inside the valve chamber and cover slab in CM 1:3, 6mm thick including cost and conveyance of all materials as per direction of deptl. officers
18.12.6:Providing and fixing G.I. pipes complete with G.I fittings including trenching and refilling etc. External work50 mm dia nominal bore
18.12.8:Providing and fixing G.I. pipes complete with G.I fittings including trenching and refilling etc. External work80 mm dia nominal bore
OD140262/2025-2026:Welding with 50mm GI pipes including all charges for cutting, cleaning, aligning and welding the pipe, conveyance of welding machine, cost of welding rods, hire charges for tools, generator, welding machine etc. and all cost of labour charges etc. complete
OD148073/2025-2026:Welding with 80mm GI pipes including all charges for cutting,cleaning,aligning and welding the pipe,conveyance of welding machine,cost of welding rods,hire charges for tools,generator,welding machine etc and all cost of labour charges etc complete.
OD140243/2025-2026:Welding with 100mm GI pipes including all charges for cutting, cleaning, aligning and welding the pipe, conveyance of welding machine, cost of welding rods, hire charges for tools, generator, welding machine etc. and all cost of labour charges etc. complete
OD140259/2025-2026:Interconnection the existing line with new line using contractors own specials including cost of materials , labour charges earth work excavation etc. complete (Up to 150 mm Diameter main line)
OD140251/2025-2026:Interconnecting the existing 100mm DI/GI pipe line with 100mm DI/GI laid line using contractor's own specials including the cost of specials , excluding the cost of EWE. etc all complete
100.35.1:Testing 100mm DI/CI pipeline with potable water to the required test pressure 100 mm dia
4.3.1:Centering and shuttering including strutting, propping etc. and removal of form work for:Foundations, footings, bases for columns
4.1.5:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)
100.60.1.4.2: Providing 15mm (1/2 inch) house connection with 15mm (1/2 inch) water meter from existing AC / GI mains up to 125 mm dia., up to a length of 5 m using 20mm Indian Standard Class 6 uPVC pipe and uPVC / GM / Brass specials viz. brass ferrule, GM full way wheel valve, Elbow, MTA, FTA, couplers, GI / MS / SS Service Saddle of suitable size etc. and connecting with the mains, testing the joints etc. complete including trenching and refilling in all kinds of soil up to a depth of 1.50m for main line tracing and trench of average cross section 0.3m x 0.75m for laying connection pipe and service pipe, fixing water meter, lighting, watching, providing caution boards, traffic control etc. complete including cost of materials, hire for tools, cost of consumables and labour charges, including the cost of tested Class B Multijet water meter with ISI mark and weather resistant PP / PE meter box of minimum size 300mm x 200mm x 150mm, but excluding charges for cutting the concrete / tarred / bituminous roads etc, and as per the direction of the departmental officers.
100.60.3.1.1:Providing additional length of house connection pipe using 20mm Indian Standard Class 6 uPVC pipe and specials and testing the joints etc., by trenching and refilling in all kinds of soil with trench of average cross section 0.3m x 0.75m for laying of connection pipe and service pipe, lighting, watching, providing caution boards, traffic control etc., including cost of materials, hire for tools, cost of consumables and labour charges etc. complete, but excluding the cost of cutting of concrete / tarred / bituminous roads etc., and as per the directions of the department officers
100.60.12.3.2:Providing 15mm PVC Tap in the water meter assembly for 15mm connection, using 20mm Indian Standard Class 6 uPVC pipes and specials including cost of consumables, hire charges for tools and labour charges etc. complete, but excluding cost of materials and as per the direction of departmental officers.
100.60.10.3.2:Providing 15mm (1/2 inch) GM Air Valve in the water meter assembly for 20mm connection, using 25mm Indian Standard Class 6 uPVC pipes and specials including cost of consumables, hire for tools and labour charges etc., complete but excluding cost of materials and as per the directions of the department officers.
13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work
13.71:Lettering with black Japan pint of approved brand and manufacture
Supply of material
100.98.115:Supply of DI K9 Pipe Conforming to IS 8329/2000, 100mm Dia.
OD140265/2025-2026:Supply of 100mm dia GI pipe (M)
100.98.440:Supply of CI Air Valve, Conforming to IS 14848 - 2000, Single Orifice, Small Orifice Type S1, Size 25mm.
100.98.482:Supply of CI Double Flanged Sluice Valve Conforming to IS 14846 - 2000, Sluice Valve with Hand Wheel PN 1.6, Size 100mm.
LAIJU.P.VARGHESE (BID ID -2394996)
Bidder Name
LAIJU.P.VARGHESE
BINCE GEORGE
stage.html
html • 0.04 MB
tech_eval.pdf
fin_eval.pdf
aoc.pdf
finance_1345888.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid