C/o link road from GPS Ghamrota Balanan Bhont Ardi Km 0/000 to 7/485 i/c Bridge over Lingti Nallah in Distt. Kangra (HP) under RIDF- XXXI NABARD

Excavation in hilly area in all heights and depths and in all kind of soil by manual/mechanical means including saturated soil comprising of ordinary soil, soft rock, hard rock, chiseling, wedging out of rock (where blasting is prohibited) and their intermediate classification of soil, setting out true to the required lines, grades, cutting and trimming of side slopes and level as shown in the drawing and as directed by engineer-In-Charge at site according to the MORD technical specification section 300 and 1600 and sorting out useful materials and stacking the same in all leads and lifts in acquired width of road and transportation of useful material for filling in road ways, camber, embankments for grade improvements and disposal of all surplus material to the approved dumping sites through all modes of transportation including head load or animal transport or mechanical means along with its leveling, fine dressing and carriage of machineries, materials, tools, equipments and safety measures and incidentals necessary to complete the work by mechanical means and labour if required. All useful material such as stones shungle, aggregate and slates etcetra shall be sorted out and stacked in proper stack. Recovery of stone to the tune of 2898.17 per cubic metre at the rate of Rs. 300/-(Rupees Three hundred) per cubic metre shall be effected from the contractor's running bills on pro-rata basis as per actual quantity executed. Any loss to the public, private / property during the course of execution shall be the absolute responsibility of the contractor, which shall have to be compensated by him in all cases including carriage of matereials within all leads and lifts and other incidentals The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Earth work in excavation for all type of road structure such as retaining walls, breast walls, culverts, drain and Parapets etcetra in all type of classification of soil comprising of ordinary soil, ordinary rock, hard rock chiseling /wedging out rocks (Where blasting is prohibited) as per drawings and M.O.R.D. technical specification section 300 and 1600 and as per direction of the Engineer- In – Charge including setting out, construction of shoring and bracing, removal of stumps and other deleterious materials and disposal of materials upto any lead and lift including dressing of sides, bottom and back filling in trenches with excavated suitable approved material to the original surface in layer not executing 150 mm (one hundred fifty millimetre) compacted thickness including shoring and strutting and pumping and bailing out water (surface and sub soil water ) upto any depth any quantam of water including cleaning of slush which may arise out during dewatering complete as per direction of Engineer-In-Charge. Including carriage of materials within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Earth work in excavation for all type of bridge structure in all type of classification of soil comprising of ordinary soil, ordinary rock, hard rock chiseling/wedging out rocks (Where blasting is prohibited) as per drawings and MORTH technical specification clause section 300, 304 and as per direction of the Engineer- In–Charge including setting out, construction of shoring and bracing , removal of stumps and other deleterious materials and disposal of materials upto any lead and upto any lift including dressing of sides and bottom and back filling in trenches with excavated suitable approved material to the original surface in layers not exceeding 150mm (One hundred fiffty millimetres) compacted thickness including shoring and strutting and pumping and bailing out water (surface and sub soil water) upto any depth and any quantam of water including cleaning of slush which may arrise out during dewatering as per direction of Engineer-In-Charge. Including carriage of materials within all leads and lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and laying mechanically mixed and virbrated plain cement concrete in open foundation for all type of road structure using of plain cement concrete grade M-10 (M Ten) nominal mix 1: 3: 6 ( One cement : Three sand : Six graded crushed/broken stone aggregate 40mm (forty millimeter) nominal size on ground or under water and curing complete including pumping or bailing out water, dewatering removal of slush as required at site which may arrise at the time of laying concrete complete for all heights/ depths including the cost of form work in road work as per drawings and MORTH technical specification section 1500, 1700 and 2100 as per the direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and laying plain/reinforced cement concrete in sub structure gradeM-20 (M-Twenty) designed mix with minimum cement contents not less than @344 Kg (Three hundred forty four kilograms) per cubic metres with 40mm (forty millimeters) nomonal size crushed stone aggregate (extra cement as per design mix above the minimum cement contents specified shall not be paid extra) in abutment etcetra as per drawings and MORTH technical specification clause 1500, 1700 and 2200 including the cost of form work and curing complete and as directed by the Engineer-In-Charge including carriage of material within all leads, lifts, height and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and laying mechanically mixed and vibrated reinforced cement concrete in sub structure grade M-30 ( M-Thirty) for design mix with cement contents not less than 407 Kg (Four hundred seven kilograms) per cubic metres with 20mm (Twenty millimeters) nominal size crushed stone aggregate (extra cement as per design mix above the minimum cement contents specified shall not be paid extra) and curing complete in Bed Block Dirt wall etcetra including cost of form work as per drawings and MORTH technical specification section 1500, 1700 and 2200 as directed by the Engineer-In-Charge including carriage of material within all leads, lifts, height and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Supplying fitting and placing HYSD bar reinforcement in sub structure of bridge work complete as per drawing and MORTH technical specifications section 1600 and 2200 including cutting, bending, binding, straightening and placing in position complete in all respect including cost of binding wire upto all height and depth as directed by the Engineer-In-Charge including carriage of material within all leads, lifts, height and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing weep holes in brick masonry / stone masonry, plain/ reinforced concrete abutment, wing walls, return walls, retaining walls with 100mm (one hundred millimetre) diameters, A.C. pipe extending through the full width of the structures with a slope of 1 (opne) vertical : 20 (isto twenty) horizontal toward drawing face complete as per drawing and MORTH technical specification section 2700 and as per direction of Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Supplying, fitting and fixing in position true to line and level POT-PTFE bearing consisting of a metal piston supported by a disc or unreinforced elastomer confined within a metal cylinder, sealing rings, dust seals, PTFE surface sliding against stainless steel mating surface, complete assembly to be of cast steel/fabricated structural steel, metal and elastomer elements to be as per IRC: 83 part-I & II respectively and other parts conforming to BS: 5400, section 9.1 & 9.2 and section 2200 of MoRTH Specifications complete as per drawing and approved Technical Specifications.and as per direction of Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing and laying mechanically mixed and vibrated reinforced cement concrete in super structure as per drawing and MORTH technical specification section 1500, 1700 and 2300 using Reinforced Cement Concrete grade M-35 (M-thirty five) designed mix with cement contents not less than 422 Kgs (Four hundred twenty two kilograms) per cubic metre with 20mm (Twenty milimetres) nominal size graded crushed stone aggregate and curing complete including the cost of form work but excluding the cost of reinforcement for reinforced concrete work in deck slab etcetera including carriage of material within all leads, lifts and other incidental, as per the directions of the Engineer-In-Charge. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and laying mechanically mixed and vibrated plain cement concrete M-15 (M-Fifteen) grade design mix with cement contents not less than 275 Kgs(two hundred seventy five kilogram) per cubic metre with 40mm ( forty milimetre) nominal size graded crushed stone aggregate in levelling course below approach slab complete including cost of form work and curing complete as per drawing and MORTH technical specifications section 1700 and 2700 as per the directions of the Engineer-In-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and laying mechanically mixed and vibrated reinforced cement concrete grade M-30 (M-thirty) designed mix with cement contents not less than 407 Kgs(Four hundred seven kilograms) per cubic metre with 20mm(Twenty milimetres) nominal size graded crushed stone aggregate (extra cement as per design mix above the minimum cement contents specified shall not be paid extra) in approach slab including cost of form work and reinforcement complete as per drawings and MORD technical specifications section 1500, 1600, 1700 & 2700 and as directed by the Engineer-In-charge including carriage of material within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and laying mechanically mixed and vibrated reinforced cement concrete Grade-M-30 (M-Thirty) designed mix with cement contents not less than 407 kgs. (four hundred seven kilograms) per cubic meter with 20mm (twenty millimeter) nominal size graded crushed stone aggregate in Wearing Coat including cost of reinforcement for reinforced concrete work form work and curing complete as per drawing and MORTH technical specification section 1500, 1600, 1700 and 2700 and as per the direction and entire satisfaction of Engineer-In-Charge including carriage of materials with in all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Supplying fitting and placing HYSD bar reinforcement in super structure of bridge work complete as per drawing and MORTH technical specifications section 1600 and 2300 including cutting, bending, binding, straightening and placing in position complete in all respect including cost of binding wire upto all height and depth as directed by the Engineer-In-Charge including carriage of material within all leads, lifts, height and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Construction of precast Reinforcement cement concrete railing with mechanically mixed and vibrated M-30 grade (M-thirty) grade design mix with cement contents not less than 407 Kg (four hundred seven kilogramme) per cubic metre with aggregate size not exceeding 12 mm (twelve millimetre) 20mm (twenty millimetre) nominal size aggregate true to line and grade , tolerance of vertical railing post not to exceed 1 in 500 (one in five hundred) centre to centre spacing between vertical posts not to exceed 2000 mm (two thousand millimetre) leaving adequate space between vertical post for expansion complete including the cost of reinforcement, form work and curing complete as per approved drawing and MORTH technical specifications section 1500, 1600, 1700 and 2700 and as per the entire satisfaction and as directed by the Engineer-In-Charge including carriage of material within all leads, lifts, height and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and fixing mild steel drainage spouts complete with 100mm ( one hundred millimeter) dia galvanised mild steel down pipe corrosion resistant structural steel grating complete as per drawing and MORTH technical specifications section 2700 and as per the direction of Engineer-in- Charge including carriage of materials within all leads , lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and laying of a strip seal expansion joint catering to maximum horizontal movement upto 70 mm (seventy millimetre), complete as per approved drawings and standard specifications to be installed by the manufacturer/supplier or their authorised representative ensuring compliance to the manufacturer's instructions for installation as per drawing and MORTH. technical specifications section 2600 complete in all respect including carriage of material within all leads, lifts and other incidentals as per the entire satisfaction and direction of Engineer – in- Charge The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and filling joint sealing compound as per drawings and technical specifications with coarse sand and 6 (Six) percent bitumen by weight complete in all respect as per MORTH specification section 2600 including carriage of material within all leads, lifts and other incidentals as per the entire satisfaction and direction of Engineer – in- Charge. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and fixing in position 20 mm (twenty millimetre) thick premoulded joint filler in expansion joint for fixed ends of simply supported spans not exceeding 10 m (ten metre) to cater for a horizontal movement upto 20 mm (twenty millimetre), covered with sealant complete as per drawing and MORTH technical specifications section 2600 complete in all respect including carriage of material within all leads, lifts and other incidentals as per the entire satisfaction and direction of Engineer – in- Charge. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

High tensile steel wires/strands including all accessories for stressing, stressing operations and grouting complete as per drawing and MORTH Technical Specifications section 1800 complete in all respect including carriage of material within all leads, lifts and other incidentals as per the entire satisfaction and direction of Engineer – in- Charge The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and errecting " W" metal beam crash barrier comprising of 3 mm (three millimetre) thick corrugated sheet metal beam rail, 70 cm (seventy centimetre) above road/ Ground level fixed on I.S.M.C. series channel vertical post 150 x 75 x 5 mm (one hundred fifty five into seventy five into five millimetre) spaced 2 m (two metre) centre to centre 1.8 m (one point eight metre) high, 1.1 m (one point one metre) below ground/ road level, all steel parts and fitments to be galvanised by hot dip process. All fitting to conforms to I.S 1367 and I.S. 1364 metal beam rail to be fixed on the vertical post with a spacer of channel section 150x75x5mm (one hundred fifty into seventy five into five millimetre) 330 mm (three hundred thirty millimetre) long complete as per section 800 & Morth technical specification as per the direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and laying mechanically mixed and vibrated plain cement concrete in all type of structure as per drawing and MORD technical specification section 800, 900 ,1200 and 1600 for nominal mix 1: 4: 8 (one cement isto four sand isto eight graded crushed/broken stone aggregate 40mm (forty millimetre) nominal size and curing complete including pumping or bailing out water, dewatering, removal of slush as required at site which may arise at the time of laying concrete complete for all heights/depths including the cost of form work in retaining walls, breast walls etcetera as per the direction of Engineer-In-Charge including carriage of materials, within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and laying 110mm (one Hundred ten millimetre) dia with working pressure not less than 4.000 kg/ cm2 (four point zero kilogram per centimetre square) ISI marked PVC pipe weep holes in brick masonry/stone masonry, plain reinforced concrete, Abutments, Wing walls, Return walls and retaining/breast walls extended through the full width of the structure with slope I(V):20(H)(One vertical : Twenty Horizontal) towards draining face complete as per drawing and MORD technical specification section 700 and 1200 and as per direction of Engineer-In-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and laying mechanically mixed and vibrated plain cement concrete in open foundation of all type of structure as per drawing and MORD technical specification section 800, 900 ,1200 for nominal mix 1: 3: 6 (one cement isto three sand isto six graded crushed/broken stone aggregate 40mm (forty millimetre) nominal size and curing complete including pumping or bailing out water, dewatering, removal of slush as required at site which may arise at the time of laying concrete complete for all heights/depths including the cost of form work as per the direction of Engineer-In-Charge including carriage of materials, within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and laying mechnically mixed and virbated plain cement concrete in sub-structure for all type of structure of using plain cement concrete grade M-15 (M-Fifteen) nominal mix 1:2½ :5 (One cement isto Two point Five sand isto Five graded crushed stone aggregate 40mm (Forty milimetres) nominal size on ground or under water and curing complete including pumping or bailing out water complete for all heights/depths including the cost of form work in toe wall and parapets etcetra as per drwings and MORD technical specification section 800, 900 and 1200 as per the directions of the Engineer-In-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and laying rubble stone flooring in cement mortar 1:3 (One cement isto three sand) laid over cement concrete bedding M-15 (M-fifteen) inclusive of its cost complete as per drawing and M.O.R.D. technical specifications section 1300 including carriage of materials with in all leads, lifts and other incidental and as per the entire satisfaction and directions of Engineer-In-Charge. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Supplying fitting and placing HYSD bar reinforcement in sub structure complete as per drawing and M.O.R.D. technical specifications section 1000 and 1200 including cutting, bending, binding and placing in position complete in all respect including cost of binding wire upto all heights / depths complete as per the directions of the Engineer-In-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Supplying fitting and placing HYSD bar reinforcement in super structure complete as per drawing and M.O.R.D. technical specifications section 1000 and 1200 including cutting, bending, binding and placing in position complete in all respect including cost of binding wire as per the directions of the Engineer-In-Charge including carriage of materials within all leads, lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and laying mechanically mixed and vibrated reinforced cement concrete in sub-structure using grade M-20 ( M-Twenty) designed mix with cement contents not less than 350kg (three hundred fifty kilogram) per cubic metre with 20mm(Twenty milimetres) nominal size graded crushed stone aggregate as per drawings and M.O.R.D. technical section 800, 900 and 1200 including the cost of form work but excluding the cost of reinforcement for reinforced concrete work in bed block and dirt wall etcetra and curing complete including carriage of materials with in all leads, lifts and other incidental and as per the entire satisfaction and directions of Engineer-In-Charge. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and laying mechanically mixed and vibrated plain cement concrete in sub structure grade M-20 (M-Twenty) design mix with cement contents not less than 330 kg (Three hundred thirty killogram) per cubic metre with 40mm (Forty millimetres) nominal size graded crushed stone aggretgate in abutments etcetra as per drawings and MORD technical specifications section 800, 900 and 1200 including the cost of form work and curing complete including carriage of materials with in all leads, lifts and other incidental and as per the entire satisfaction and directions of Engineer-In-Charge. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and laying mechanically mixed and vibrated Reinforced Cement Concrete work in super-structure grade M-25 (M-Twenty five) design mix with cement contents not less than 400 Kgs(Four hundred kilogram) per cubic metre with 20mm(Twenty milimetres) nominal size graded crushed stone aggregate as per drawing and M.O.R.D. technical specification section 800, 900 and 1400 including the cost of form work and curing complete but excluding the cost of reinforcement for reinforced concrete work in deck slab including carriage of materials with in all leads, lifts and other incidental as per the entire satisfaction and direction of Enginee-In-Charge. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and laying mechanically mixed and vibrated plain cement concrete grade M-15 (M-Fifteen) nominal mix 1:2½:5 (One cement isto Two and half sand isto five graded crushed stone aggregate 40mm (Forty millimetres) nominal size) on ground or under water and curing complete including pumping or bailing out water complete for all heights/depths including cost of form work in craddle bedding Type- A as per drawing and MORD technical specification section 800, 900 and 1100 including carriage of materials with in all leads, lifts and other incidental, as per the entire satisfaction and directions of Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and laying mechanically mixed and vibrated reinforced cement concrete Grade-M-30 (M-Thirty) designed mix with cement contents not less than 430 kgs. (four hundred thirty kilograms) per cubic meter with 20mm (twenty millimeter) nominal size graded crushed stone aggregate in Wearing Coat including cost of reinforcement for reinforced concrete work form work and curing complete as per drawing and MORD technical specification section 800, 900, 1000 and 1400 and as per the direction and entire satisfaction of Engineer-In-Charge including carriage of materials with in all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Construction of Reinforcement cement concrete railing of M-25 grade (M-twenty five) in cast in situ with 20mm (twenty millimetre) nominal size aggregate true to line and grade , tolerance of vertical railing post not to exceed 1 in 500 (one in five hundred) centre to centre spacing between vertical posts not to exceed 2000 mm (two thousand millimetre) leaving adequate space between vertical post for expansion complete including the cost of reinforcement, form work and curing complete as per approved drawing and MORD technical specifications section 800, 900, 1000 and 1200 and as per the entire satisfaction and as directed by the Engineer-in-charge including carriage of material within all leads, lifts, and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and laying mechanically mixed and vibrated reinforced cement concrete grade M-25 (M-Twenty five) designed mix with cement contents not less than 400 Kgs(Four hundred kilograms) per cubic metre with 20mm(Twenty milimetres) nominal size graded crushed stone aggregate (extra cement as per design mix above the minimum cement contents specified shall not be paid extra) in approach slab including cost of form work, reinforcement and curing complete as per drawings and MORD technical specifications section 800, 900, 1000 and 1400 as directed by the Engineer-In-charge including carriage of material within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and laying mechanically mixed and vibrated plain cement concrete M-15 (M-Fifteen) grade design mix with cement contents not less than 275 Kgs(two hundred seventy five kilogram) per cubic metre with 40mm ( forty milimetre) nominal size graded crushed stone aggregate in levelling course below approach slab complete including cost of form work and curing complete as per drawing and MORD technical specifications section 800, 900 and 1200 as per the directions of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and laying (to level or slope) 900mm dia (nine hundred millimetres) diameter reinforced cement concrete heavy duty non pressure pipes IS Class NP3 for culverts on first class bedding of granular material in single row including providing and fixing collar with cement mortar 1 : 2 ( One cement isto two sand) but excluding the cost of excavation, protection works, back filling, concrete bedding and masonry work in head walls and parapets as per drawing and M.O.R.D. technical specifications section 1100 and as per direction of Engineer – in- Charge including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Loosening of the ground upto a level of 300 mm (three hundred millimetre) below the subgrade level, watered, graded with motor grader and compacted in layers to meet requirement of Tables 300.1 and 300.2 with three wheel 80-100 (eighty to one hundred) KN static roller for subgrade construction as per MORD Technical Specification section 300 and as per direction of Engineer-In-Charge. Including carriage of materials within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading by mechanical means to required slope and compacted with three wheel 80-100 (eighty - one hundred) kN static roller to meet requirement of Table 300.2 complete as per MORD technical Specification section 400 and as per direction of Engineer-In-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Construction of granular sub-base 150mm (one hundred fifty milimeters) compacted thickness by providing well graded materials as per table 400.1 spreading in uniform layers with tractor mount grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with three wheel roller 80-100 (Eighty- one hundred) kN static roller to achieve the desired density, complete as per MORD Technical Specification section 400 for grading-I material, as per the entire satisfaction and directions of Engineer-In-Charge including carriage of material with in all leads, liftsand other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing, laying, spreading and compacting by mechanical means crushed stone aggregate size 63mm to 45mm ( sixty three millimetre to forty five millimetre) Grading-II [75mm ( seventy five millimetres) consolidated thickness) to water bound Macadam specification including spreading in uniform thickness using template, hand packing, rolling with three wheel 80-100 (eighty to one hundred) K.N. static roller in stages to proper grade and camber including applying and brooming, stone screening type-B of size 11.2mm ( eleven point two milimetres) nominal size at the rate of 0.20 cum ( zero point two zero cubic metres) per ten square metres and binding material at the rate of 0.06 cum ( zero point zero six cubic metre) per ten square metre to fill up the interstices of coarse aggregate, watering and compacting to the required density as per M.O.R.D. technical specifications section 400 and as per the entire satisfaction and direction of Engineer – in- Charge including carriage of materials within all leads, lifts and other incidental The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing, laying, spreading and compacting by mechanically means stone aggregate size 53mm to 22.4mm (fifty three millimeter to twenty two point four millimeter) Grading-III size [75mm( seventy five millimeters) compacted thickness] to water bound macadam specification including spreading in uniform thickness using template, hand packing, rolling with three wheel 80-100 (eighty- one Hundred) K.N. static roller in stages to proper grade and camber, applying and brooming, stone screening type-B of size 11.2mm (eleven point two milimetres) nominal size at the rate of 0.18cum (zero point eighteen) cubic metres per 10 Sqm (per ten square metres) and to fill up the interstices of coarse aggregate, watering and compacting to the required density as per MORD technical specifications section 400 and as per the entire satisfaction and direction of Engineer–In-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and applying primer coat with BITUMEN emulsion (SS-1) on the prepared surface of granular base including cleaning of road surface with hydraulic brooms and spraying primer at the rate of 0.85 Kgs per Sqm. (zero point eight five kilogram) per square metre using mechanical means as per MORD technical specifications section 500 as per the entire satisfaction and as per direction of Engineer – in- Charge including carriage of materials within all leads, lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.275 kgs (Zero decimal Two Seven Five kilogram) per square metre on the prepared granular surface treated with primer and cleaned with Hydraulic broom as per MORD Technical Specification section 500 as per direction of Engineer-In-Charge including carriage of materials within all leads, lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing, laying and rolling of open graded premix carpet of 20mm (twenty millimetre) compacted thickness, composed of 13.2mm to 5.6 mm (thirteen decimal two millimeter to five decimal six millimetre) aggregate at the rate of 0.27 cum (Zero point two seven cubic metre), premix with bitumen binder VG-10 (Viscosity Grade ten) at the rate of 14.6 kg (Fourteen point six kilogram) per ten square metres of road surface to required line, grade and level to serve as wearing course on a previously prepared base including mixing and heating binder and aggregate in Hot Mix Plan 30/40 (Thirty/Forty tonne) per hour capacity, transporting mixed material with tipper and laying with paver finisher to the required grade and rolling complete with three wheel roller 80-100 (Eighty - one Hundred) Kn static roller finished to required level and grade as per MORD technical specifications section 500 including carriage of material with in all leads and lifts, and other incidentals as per the entire satisfaction and direction of Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and laying seal coat for sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type B seal coat using VG-10 (viscosity grade ten) bitumen at the rate of 6.8 Kg (Six point eight kilogramme) premixed with 0.06 (Zero point zero six) cubic metre of fine aggregate per 10 sqm (Ten square metre) heated in mini hot mix plant and laying of mixed material and rolling with power road roller 8-10 (Eight to Ten ) tonne capacity as per MORD Technical Specification section 500 complete as per the direction of Engineer-In-charge, including carriage of material within all leads, lifts of materials and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and laying mechanically mixed and virbrated plain cement concrete in open foundation for all type of road structure using of plain cement concrete grade M-10 (M Ten) nominal mix 1: 3: 6 ( One cement isto Three sand isto Six graded crushed/broken stone aggregate 20mm (twenty millimeter) nominal size on ground or under water and curing complete including pumping or bailing out water , dewatering removal of slush as required at site which may arrise at the time of laying concrete complete for all heights/ depths including the cost of form work in drain as per drawings and M.O.R.D. technical specification section 800, 900 and 1200 as per the direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement and any other equivalent type as per Clause 1501 using M30 (Grade),(design mix) concrete having coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm (twenty five millimetre), mixed in a concrete mixer of not less than 0.2 cum (zero point two cubic meter) capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 (one hundred twenty five) micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14 (fourteen) days using curing compound (where specified) and water finishing lines and grade as per drawing and MORD Technical specification section1500 and as directed by the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Reinforced cement concrete M-15 (M-fifteen) grade fifth Kilometer Stone (Precast) of standard design as per IRC :8 fixing in position including painting and printing etcetera as per drawing and MORD technical specification section 1700 and as per the directions of the Engineer-in-Charge including carriage of material, within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Reinforced cement concrete M-15 (M-fifteen) grade Ordinary Kilometer Stone (Precast) of standard design as per IRC :8 fixing in position including painting and printing etcetera as per drawing and MORD technical specification section 1700 and as per the directions of the Engineer-In-Charge including carriage of material, within all leads, lifts and other incidentals, . The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Reinforced cement concrete M-15 (M-fifteen) grade 200m (two hundred metre) Stone (Precast) of standard design as per IRC :8-1980 fixing in position including painting and printing etcetera as per drawing and technical specification section 1700 and as per the directions of the Engineer-In-Charge including carriage of material, within all leads and lifts and other incidentals, . The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and fixing of Semi-reflective cautionary, mandatory and informatory sign board 600mm (six hundred millimetre) equilateral triangle as per IRC-67 made of 1.5 mm (one point five millimetre) thick MS-sheets duly stove enameled paint in white colour in front and gray colour on back with red reflective border of 65 mm (sixty five millimetre) width and required letters and figures with reflective tape engineering grade as per Clause 1701 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47mm of 12 SWG ( forty seven into forty seven millimetre of twelve Standard Wire Gauge) sheet square tube firmly fixed to the ground by mean of properly designed foundation with M-15 grade ( M-fifteen grade) cement concrete 450mm x 450 mm x 600 mm ( four hundred fifty into four hundred fifty into six hundred millimetre), 600 mm ( six hundred millimetre) below ground level as per drawings and MORD Technical Specification section 1700 including painting angle iron post with primer and two coat of Epoxy paint as per specification and as per the direction of Engineer-In-Charge including carriage of materials within all leads, lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and fixing of Semi-reflective cautionary, mandatory and informatory sign board 600mm (six hundred millimetre) Circular as per IRC-67 made of 1.5 mm (one point five millimetre) thick MS-sheets duly stove enameled paint in white colour in front and gray colour on back with red reflective border of 65 mm (sixty five millimetre) width and required letters and figures with reflective tape engineering grade as per Clause 1701 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47mm of 12 SWG ( forty seven into forty seven millimetre of twelve Standard Wire Gauge) sheet square tube firmly fixed to the ground by mean of properly designed foundation with M-15 grade ( M-fifteen grade) cement concrete 450mm x 450 mm x 600 mm ( four hundred fifty into four hundred fifty into six hundred millimetre), 600 mm ( six hundred millimetre) below ground level as per drawings and MORD Technical Specification section 1700 including painting angle iron post with primer and two coat of Epoxy paint as per specification and as per the direction of Engineer-In-Charge including carriage of materials within all leads, lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and erecting direction and place identification semi-reflective sign boards more than 0.90 sqm (zero point nine zero) square metre size board, as per IRC-67 made of 2.0mm (two point zero millimeter) thick MS sheets duly stove enamelled paint in white colour in front and gray colour on back with red reflective border of 70mm (seventy millimetre) width and required message, letters and figures with reflective tape engineering grade as per clause 1701 of MORD for rural roads of required shade and colour supported and welded on 47mm x 47mm of 12 SWG (forty seven into forty seven millimetre of tewlve standard wire gauge) sheet square tube of 3050mm (three thousand fifty millimetre) height duly strengthened by 25mm x 5mm (twenty five millimetre into five millimetre) mild steel flat iron on edges on back firmly fixed to the ground by mean of properly designed foudation with M-15 grade (M-fifteen grade) cement concrete 450x450x600mm (four hundred fifty into four hundred fifty into six hundred millimeter) , 600mm ( six hundred millimeter) below ground level as per drawings and MORD technical specification clause 1700, including painting angle iron post with primes and two coats of Epoxy paint as per specification and direction of Engineer-In-Charge including carriage of materials within all leads and lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Guard Stone on Curve made of Reinforced cement concrete / local stone of standard design as per IRC:25, fixed in position including finishing and lettering but excluding painting as per drawing and MORD technical specification section 1700 and as per direction of Engineer-In-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, Malkhana, toll tax, GST and other taxes imposed by the Government.

Please Enable Macros to View BoQ information