PROVN OF KOTA STONE FLOORING IN VARANDHA OF OR LIVING BARRACK AND COOK HOUSE BLDG NO P348 P350 P357 PROVN OF TWO TOILETS AND ONE BATHROOM NEAR MT PARK OF ASCE RAIWALA AND PROVN OF SIX GEYSERS AND CONNECTED ACCESSORIES FOR OR COOK HOUSE BLDG

Amount

Demolition of cement concrete (un-reinforced) in Ground floors and paving n.exe 15cm thickness ( below or above ground level ) including removal of rubbish out side complex (MOD land), complete all as specified and directed.

M & L for 25 mm thick Plain cement concrete type 1:2:4 B-0 (using 12.5 mm graded stone aggregate) in sub base of flooring complete all as specified and directed.

M & L for machine cut pre polished kota stone slab flooring 20-25mm thick over 20 mm thick screed bed in cement mortar 1:4 cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, moulding and mirror polishing complete all as specified and directed.

Taking down cement plaster, terrazzo dado in any thickness from brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M & L for 16-18 mm thick machine cut pre polished kota stone slab in riser of steps, skirting,dado and pillar laid over over 15 mm thick screed bed in cement mortar 1:4 cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, moulding and mirror polishing complete all as specified and directed.

Takig down and Refixing of shutters in same opening of any descrption after easing and adjusting , area of each shutter exc 1.00 Sqm but n exc 2.00 Sqm each complete all as specified and directed.

M&L preparation of old painted surface of wall and applying one coat of oil bound distember complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m deep for foundation ,etc and getting out in any type of soil complete all as specified and as directed.

M & L for Plain Cement Concrete 1:4:8 Type D-2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and as directed.

M&L Brick work with sub-class `B' bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 complete all as specified and as directed.

M&L Brick work with sub-class `B' bricks, straight or curved on plan to any radius as in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.

Returning, filling in, including spreading, levelling , watering, and well ramming in layers n.exc 25 cm thick complete all as specified and as directed.

M & L for 40 mm thick Cement Concrete 1:2:4 Nominal Mix Tupe B-0 (using 12.5 mm graded stone aggregate) as in damp proof course (DPC) to horizontal or vertical surfaces including necessary form work with and including water proofing compound, mixing of WPC will be done as per manufacturer’s instructions complete all as specified and directed. NOTE: - The water proofing compound not will be measured and paid separately.

Removing excavated material (Soil) to a distance n. exc 50m and depositing where directed at a level n. exc. 1.5m above the starting point complete all as specified and as directed.

M&L for Hard core of Broken stone of gauge n exc 63mm thick of broken boulders, spread, levelled, watering & well ramming to true surface complete all as specified and directed.

M&L for 75 mm thick P.C.C 1:4:8 type D-2(using 40mm graded stone agg) as in sub base of floor complete all as specified and as directed.

M & L for 25 mm thick PCC 1:2:4 type B-0, (using 20 mm graded stone aggregate) as in flooring including finishing cement concrete rough surface to receive floor finishes complete all as specified and directed.

M&L for coloured ceramic tiles of any design and pattern, (all as approved by GE/AGE (I) ) , 7 to 8 mm thick (square/rectangular) area of each tile exe 0.11 sqm but not exe 0.18, in floor etcover & incl 15mm thick screed bed in CM 1:6 , set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles . Tiles shall be confirming to IS-15622.2006, Group B II with average water absorption between 3% to 6%. Length, width and straightness of sides + 0.10% (Max deviation). Thickness + 5.0% (Max deviation). Centre & Edge curvature and warpage + 0.50% (Max deviation). Breaking strength 1000 N (Minimum) and minimum 95% tiles shall be free from visible defects complete all as specified and directed. Note:- Shade of the tiles including Colour, design and pattern shall be approved by AGE (I)

M&L for coloured glazed ceramic tiles of any design and pattern, (all as approved by GE/AGE (I) ), 300x450x 7 to 8 mm thick, as in dado etc incl 10 mm thick rendering in CM 1:4, Set and jointed in neat cement slurry and pointed in white of coloured cement to match the shade of the tiles . Tiles shall be confirming to IS-15622:2017, Group B III with average water absorption between 10% to 15%. Length, width and straightness of sides + 0.20% (Max deviation). Thickness + 4.0% (Max deviation). Straightness of sides and Rectangularity +0.15% (Max Deviation). surface flatness + 0.22% (Max deviation). Breaking strength 500 N (Minimum) and minimum 95% tiles shall be free from visible defects complete all as specified and directed. Note:- Shade of the tiles including Colour, design and pattern shall be got approved by AGE(I) .Complete all as specified and directed

M&L Rendering 15 mm thick on other than fair faces of brick work or concrete walls surfaces in CM 1:6 finished to even & smooth without using extra cement complete all as specified and directed.

M&L Rendering 15 mm thick on fair faces of brick work or concrete walls surfaces in CM 1:4 finished to even & smooth without using extra cement complete all as specified and directed.

M&L Rendering 10 mm thick on fair faces of brick work or concrete surface of ceiling in CM 1:3 finished to even & smooth without using extra cement complete all as specified and directed.

M&L for preparing newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed.

M&L for two coat of cement base paint on new plastered surface of wall over one coat of primer including preparation of surface complete all as specified and as directed.

M&L for preparing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and as directed.

M & L for providing reinforced cement concrete 1:2:4 Type B-1 Nominal Mix (using 20 mm graded stone aggregate) as beams , cantilevers, bressummers , lintel over 1.5 mtr span complete all as specified and directed. (Note:- Reinforcement & form work shall be measured and paid separately under respective item of Sch A)

M&L RCC 1:2:4 type B1 (using 20mm graded aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc complete all as specified and directed.

Form work rough finished surfaces of concrete to sides and soffits of beams , lintel and similar items complete all as specified and directed.

Form work to soffits of suspended slabs such as roof slabs, floor slabs and similar work n.exc 200 mm thick rough finished flat surfaces of concrete complete all as specified and directed.

M&L for mild steel TMT bars10mm dia & over, cut to length, bent to shape required including cranking bending spirally & binding with and in including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required including cranking bending spirally & binding with and in including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F 100mm X 63mm Single Rebate Factory made 100 % Solid WPC door Frame made from 100% LEAD FREE (single extruded process) material with density 780 kg/Cum & Manufactured by an ISO: 9001-2015 certified company, all as per specification. The door frame should be Water Proof , Termite Proof , Fire Retardent and having excellent screw holding capacity complete all as specified & directed. Make:- ENCHON (Kumar Arch Tech Pvt Ltd)/FLORESTA/ARCHIDPLY

M&L 30mm thick Factory made molded cloured 100 % solid door (confirming As per IS 4020) made from 100 % lead free single extruded with 2, 4 or 6 raised panel design on the front side with 10mm deep mould on single side with wood grain texture and back side plain with density not less than 600 kg/cum. manufactured by an ISO: 9001-2015 certified company. The door should be water proof, termite proof , fire retardent and having screw holding capasity.complete as per direction of Engineer-in-charge, manufacturer's specification and drawing complete all as specified & directed. Make:- ENCHON (Kumar Arch Tech Pvt Ltd)/FLORESTA/ARCHIDPLY

M&L Second class hard wood plain, solid, straight chowkats (SAL) and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S & F 30 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (with sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc. for windows and ventilators etc complete all as specified and directed.

M&L Glazing with figured glass (Frosted), pin head type, 4 mm thick and glazing with oil putty or aluminium or PVC beading in squares not exceeding 0.5 Sq.m in each pane complete all as specified and directed.

S & F for Aluminium anodized barrel tower bolt of 12 mm dia and 150 mm length of extruded section (ISI Marked) complete all as specified and directed

S & F for Aluminium anodized barrel tower bolt of 12 mm dia and 100 mm length of extruded section .(ISI Marked) complete all as specified and directed.

S & F 100 mm long extruded Aluminium alloy anodised Butt hinges (ISI Marked) with galvanized mild steel hinge pin type C 21 complete all as specified and directed.

S & F 75 mm long extruded Aluminium alloy anodised Butt hinges (ISI Marked) with galvanized mild steel hinge pin type C 21 complete all as specified and directed.

S&F for Extruded Aluminium alloy handles,fabricated type, anodised 150 mm long, (ISI Marked) complete all as specified and directed.

S & f for Aluminium alloy anodised sliding door bolt, of size 300mm, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections of cast aluminium alloy complete all as specified and directed

M&L cement concrete 1:3:6 type C-1 (using 20mm graded aggregate) 75 mm thick as in plinth protection surface finished even and smooth without using extra cement including 4 mm thick glass dividing strip of figured glass, pin headed type, 73 mm wide inserted in position complete all as specified and directed.

S&F in repair Wash basin (Padestal Pattern) of size 550x400mm vitreous china (flat back type) any size (ISI Marked) incl cutting for and pinning in end of brackets for erecting stand but exclusive of fixing of supply and waste pipe but including waste fittings complete all as specified & directed. Make:-Jaquar Cat No-ECS-WHT-801 (WHB) & ECS-WHT-301(PEDESTAL), Hindware Cat No-Mario 10087 (WHB) & 11003(PEDESTAL) ,Cera Cat No-S2040120(WHB) & S2090113(PEDESTAL)

S & F Vitreous china urinal, bowl type flat back of size 465 x 355 x 265 mm white (minimum), (ISI Marked) with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, complete all as specified & directed.

S & F 15 mm bore Stop valves (angular stop cock), cast copper alloy, fancy type, chromium plated with long shank and cup (ISI Marked) screwed down high pressure with crutch or butterfly handle or concealed screwed both ends for iron pipe or for unions complete all as specified and directed. Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site

S & F for Brass CP urinal spreader fixing with 15mm dia pipe complete all as specified & directed . Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site

S & F in repairs 15 mm bore chromium (ISI Marked) plated bib taps long body, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified & directed. Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site

S & F in repairs 15 mm bore pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, (ISI Marked) screwed for iron pipe complete all as specified & directed. Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site.

S & F in repairs (ISI Marked) Chromium plated shower rose 125 mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified & directed. Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site.

S&F in repairs Vitreous china Squatting pan , 'Orissa pattern, (ISI Marked) of size 580x440 mm white, with integral foot rest excluding flushing cistern and flush pipe including connection to trap, to flushing pipe and anti-syphonage pipe, etc complete including making good to floor complete all as specified & directed.

S&F in repairs 10 liter capacity PVC valveless, syphonic action type flushing cistern (Dual action ISI Marked), low level , white, with inlet ball valve, float and handle including brackets and flush pipe suitable for indian Type WC of polyethylene of low or high density or PVC 32 mm dia for low level cistern complete all as specified & directed.

S&F for PVC Connections 15mm size with PTMT nuts of length 600 mm (ISI Marked) complete all as specified & directed.

S&F 75mm PVC (SWR) floor trap, (ISI Marked) plain with grating including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC (SWR) Soil, waste and vent pipes (ISI Marked) single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and as directed.

S & F 110 mm bore PVC (SWR) Soil, waste and vent pipes (ISI Marked) single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

S & F 75 mm bore PVC (SWR) Soil, waste and vent pipes (ISI Marked) single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

S & F 110 mm bore PVC (SWR) bends (ISI Marked) of any radius complete all as specified and as directed.

S & F 110 mm bore PVC (SWR) junction single (Single`T') (ISI Marked) equal or unequal with access door complete all as specified and as directed.

S & F 75 mm bore PVC (SWR) Vent Cowl (ISI Marked) complete all as specified and as directed.

M&L for Mild steel galvanized steel tubing of 15 mm bore (ISI Marked) with screwed socket joints as in concealed pipe work , medium grade, together with all fittings heavy grade (ISI Marked ) (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc) and fixed complete to walls and ceiling with clips, wall hooks, wooden plugs or laid in floors Complete all as specified and directed

S&F Rotational moulded polyethylene water storage tank 1000 liters capacity, white two layer (ISI Marked) construction (cylindrical vertical with closed top), hoisted & fixed in position including all fittings complete all as specified and as directed.

S&F 20mm dia ball valve (ISI Marked) high pressure PTMT with epoxy coated aluminium rod & high pressure plastic ball screwed for iron pipe and fixed complete all as specified and as directed.

M&L Concrete bed to drain pipe 110mm dia incl. packing under and haunching against the sides of pipe PCC 1:4:8 type D2 (Using 40 mm graded stone agreegate) complete all as specified and as directed.

Cutting into existing manholes 100 mm dia for connecting new drains making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 round section) in cement concrete 1:2:4 type B1, smooth finished and reforming benching as required, 100mm dia pipe complete all as specified and as directed.

Material & Labour for Point Wiring for one light Point/one fan point/ one call bell point, controlled by one no one way 5 Amp switch with 1100 volts grade single core conforming to (IS:694 /1990) PVC insulated unsheathed 1.5 sqmm multi stranded copper conductor cable (FRLSH) with continious earth wire of 1.5 Sqmm stranded copper conductor cable (FRLSH) PVC insulated unsheathed , drawn in and including concealed non metallic rigid PVC conduit,medium grade(ISI marked) ,duly concealed on wall/ceiling or above false ceiling with fittings not less than 20 mm dia medium grade (Color coding of wires shall be Phase, neutral and earth wire all as specified ) sunk mild steel/pressed steel Metal flush box thickness not less than 1.6mm painted with black bituminus paint from out side and two coat aluminium paint inside for housing switches, sockets , fan regulators etc covered with 2.80 mm thick white laminated 'Bakelite' sheet (ISI Marked) cover plate complete all as specified and directed. Note:- (i) Cost of cutting chases of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted rates. ii) If the contractor fail to make good the disturbed surface of wall/ceiling etc and do not match with the existing surface of wall/ceiling to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding.

All as per item No 67 above but for 2.5 Sqmm wiring for Geyser point controlled by one no of sheet metal enclousre

M & L for switch piano 230 volts, AC, flush type, single pole one way 6 Amps ISI marked complete all as specified and as directed.

Supply and fixing ceiling rose surface bakelite 65/25 mm dia AC 220/240 volts having three terminals (ISI Marked) complete all as specified & directed.

S&F surface mounted LED luminiare, 10 watt with all accessories having polycarbonate extruded channel with diffuser for glare free light, high lumen output, driver PF >0.98 having over voltage protection upto 400 volts surge protection, level 7-10 KV thermal short circuit protection THD<10%, made up of long life LED chips (SMD) in modular with Ra>70 and lumen efficiency >120 lumen per watt, Inverter LED batten with square profile, inbuilt Lithium Ion battery with charging time 8-10 hours and back up time up to 4 hours, 6500 K internally pre-wired through flexible wire connecting with ceiling rose all as directed. Note:- The firm has to give warranty for fitting including driver minimum for 3 years for any defects developed during the period.

Supply and fix LED street/security light fitting 20W housing made out of pressure die-cast aluminium alloy with toughned glass, IP-66 protection, working on 240 Volts AC, 50 HZ, consisting of reflective lens wired with approximate driver PF>0.98 having over voltage protection upto 440 volts, Surge protection level 7-10 KV, thermal short circuit protection THD < 10% made up of long life LED chips (SMD) in modular with Ra>70, and LED lumen efficiency >140 lumen per watt, beam angle along the drive way, 120 degree, beam angle across the drive way, 80 degree luminior efficiency > 120 Lumens/watt power LED should be of more than 01 watt CCT should be between 5700 K- 6500 K including fixed on wall with 02 Nos MS clamp made out of 40 x 6 mm F1 and bracket made out of 40 mm dia light grade GI pipe not less than 1.0 mtr long bend to shape with use reducer for inner dia 38 mm for fix with inside light fitting including connecting with 1.5 sq mm, 3 core, PVC insulated Copper conductor cable 1100 Volta grade complete all as specified and as directed. Make:- Havells cat No: LHEXAYP7PN6K020 or Shakti cat No: SZPCLPM020 or Crompton cat No; TRP-400-20-57-SL-LM-NSR Note :- (i) the firm has to give warranty for street light fittings including driver minimum for 03 years for any defects developed during the period. (ii) The contractor shall submit the third party LM 79 & LM 80 report from any NABL approved laboratory. (iii) The fitting should have BIS, CRS (iv) Connection to luminaire shall be done in suitable PVC connector within the bracket/luminaire end and rates are inclusive in above.

M & L sheet metal MCB DB SPN 04 way 240 volts, double door type powder coated with 200 Amps rated bus bar, neutral link, earth rail & din rail, ISI marked for housing MCBs and making good for distrubed surface with existing etc complete all as specified and directed Note:- (i) MCBs measured and paid for separately under respective items. (ii) when PVC cables connected to MCBs use suitble size of copper connectors for connection and Incoming UG cable use suitable size of lugs for connect cable through MCBS on DB. The cost of the same shall deemed to be included in the unit rate quoted by the contractor.

S&F MCB SPN 16-32 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB), ISI marked, 50 hz with cable connection and copper lugs complete all as specified and directed.

S&F 10 KA 'C' curve miniature, circuit breaker (MCB) of single pole and neutral, current carrying capacity 5 to 32 AMP ISI marked, 230/240 volts, 50 Hz in the MCB DB Complete with connection testing and commissioning complete all as specified and directed.

S&F sheet metal enclosure with socket and plug top including fitted with RCBO of 10 Amps, 30 mA protection and one MCB SPN 10 amps controlled on Geyser complete all as specified and directed.

Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. ( earth pit not less than 2.25 mtr depth below ground level at any type of strata ) with top edge of the earth plate not less than 1.5mtr below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15cm all around the plate. connected by 4 mm GI wire as earth lead by means of brass nuts and bolt, thimbles check nuts, washers including concrete chamber of PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM 1:4 funnel with wire mesh, RCC pit cover of 320x320x80mm size (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI wire upto 7.5 mtrs long with 15 mm dia light grade GI pipe protection and watering pipe of GI 20 mm bore, medium grade, including all exavation and earth work and connecting the earthing wire to panel, including testing on completion and taking down old unserviceable earthing complete all as specified and directed by Engr-in-charge. Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick rainforced with XPM weighing not less than 4kg/sqm in lieu of CI cover. (ii) Cost of additional GI wire more than 7.5 mtrs will be measured and paid seperately under relevant items.

S&F Exhaust fan AC single phase 230/240 Volt of size 300 mm sweep, metallic body powder coated painted finish, Power consumption- 50 W, Air deplacement -1290 Cum/Hr, RPM-900 complete with louvers including making whole and grouting of nut bolts etc and making good the disturbed sufaces of wall complete all as specified and directed. Make - Orient/Bajaj/Havells/Crompton

M&L for fixing or passing through pipe, laid in trenches, fixed on wall, LT panel board, XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of size 10 sqmm 2 core with required aluminium cable lugs, lugs should properly crimp with crimpping tools, heat shrink joints, Colour code heat shrink sleeves at both cable ends , cable gland for cable safety when passing through panel holes, including laying cable route indicators of suitable size RCC or steel type as per site requirement, complete all as specified and directed. Note: Ecavation & earth work/GI tubing required shall be measured and paid separately under relevant item of sch A.

M&L for fine dry sand cushioning for underground cable by providing layers of sand 8 cm before laying and 15 cm deep after laying the cable including streching the cable complete all as specified and directed. Note:- Measurement of sand to be taken consolidated thickness after punning down.

M & L for cable protection bricks common burnt clay sub class 'B' designation 75 for protection of UG cable laid in trenches all as specified and directed at site complete all as specified and directed.

M&L for road cutting and making good with PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) of minium size 150mm X 100mm in respect of width and thickness complete all as specified and directed.

Supply, laying & joined Galvanised Tubing 50 mm bore, light grade as in sleeving etc laid in trenches/pole post/under culvert/under road etc for cable protection including taking down old one complete all as specified and directed.

Supply and laying 20 mm dia GI pipe "Medium grade" galvanized, including all fittings as required on under ground and connecting near by exisiting pipe line complete all as specified and directed.

Cutting of existing GI pjpe of size 40 to 50 mm bore in position for insertion of new branch line of any bore complete all as specifed and directed.

S & F 40 mm dia Gun Metal, globe or Gate Valve (ISI Marked) Class 150 with Iron wheel head Screwed both ends for Iron Pipe and fixed complete all as specified & directed.

M & L for sub main wiring two single core 2.5 sq mm PVC insulated unsheathed stranded copper conductor cable ( FRLSH ) 1100Volts grade drawn in & including rigid PVC conduit 20mm dia or more medium grade concealed in wall as per along with 2.50 Sq mm PVC insulated unsheathed copper conductor cable (FRLSH) as earth wire and wire connected with main earth dolly including cutting chases of existing brick/masory wall and making good disturbed portion complete all as specified and directed . Note:- Two runs of phase, netural wire and one run of earth wire and PVC conduit shall be measured as one RM or one length.

Fixing only electric water heater,storage type steel body/ABS body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE approved, 5 Star rated complete all as specified and directed. Note:- (i) The Geyser will be issued by the department under Sch B 'free for fixing'. (ii) The accessories required for fixing geyser such as NRV, Hot and cold water pipe connection, 10 mm anchor fastener of required size on site, the ibid items and required qty shall deemed to be included in the unit rate quoted by the contrctor.

S & F Stop valve 15 mm dia, cast copper alloy, screwed down, high pressure,with crutch or,butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S & F Bib taps,15 mm cast copper alloy fancy type, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

SWASTIKA BUILDERS