CA NO GE(N)AMB-52(P)/2020-21 REPAIR TO JOINERY, PLUMBING, SANITARY, ROOF ,PLASTERING AND OTHER CONNECTED BLDG REPAIR WORKS IN AREA-IV AND OTHER AREA IN OTM OF SECTOR B UNDER AGE B/R-1 OF GE(N) AMBALA CANTT

Amount

M&L 10 mm thick cement plaster in CM 1:3 on concrete surfaces finished even and smooth with out using extra cement on ceiling including taking down cement or cement lime plaster of any description on ceiling surfaces, hacking for key, scrubbing down with water etc complete all as specified and as directed by the Engr-in-charge.

M&L 15 mm thick cement plaster on brick or concrete walls in CM 1:6 finished even and smooth with out using extra cement including taking down cement or cement lime plaster of any description on brick or stone walls etc including raking out joints, hacking for key scrubbing down with water etc complete all as specified and as directed by the Engr-in-charge.

M&L rendering 15 mm thick cement plaster on fair faces of brick works in CM 1:4 finished even and smooth with out using extra cement on brick work or concrete wall surfaces mixed with water proofing compound @ 3% by weight of cement or as per manufacturer’s instruction (cost of WPC shall be deemed to be including in this item) including taking down cement or cement lime plaster of any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed by the Engr-in-charge.

Material and labour for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 kg of cement per SQUARE METRE, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping of 10mm nominal size) in panels, with groove all around as per approved pattern including scrubbing and washing the top layer with brushes and water to expose the stone chippings complete all as specified and as directed by the Engr-in-charge.

M&L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper using painting roller over 2 to 3mm thick wall care putty in two or more coats for making surface smooth complete all as specified and as directed by the Engr-in-charge.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white lime wash complete all as specified and as directed by the Engr-in-charge.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement based paint over a coat of primer complete all as specified and as directed by the Engr-in-charge.

M&L for complete removal of existing treatment and applying two coat of cement based paint over recently prepared old plastered surfaces of wall complete all as specified and as directed by the Engr-in-charge.

M&L for preparation of old plastered /unplastered wall surfaces and applying two coats of white lime wash complete all as specified and as directed by the Engr-in-charge.

All as per item No 1.09 above but on ceiling, complete all as specified and as directed by the Engr-in-charge.

M&L for applying two coats of exterior emulsion including complete removal of existing treatment of old painted surfaces of wall complete all as specified and as directed by the Engr-in-charge.

M&L for preparation of old plastered brick/concrete wall and applying two coats of oil bound distemper over recently prepared old painted surfaces of wall including 2 to 3 mm thick wall care putty in two or more coats for making smooth surface complete all as specified and as directed by the Engr-in-charge.

M&L for preparation of old plastered surface of brick/concrete wall and applying one coat of oil bound distemper over recently prepared old painted surfaces of wall complete all as specified and as directed by the Engr-in-charge.

M&L for preparation of old surfaces of steel any description over 10 cm width or girth by scrubbing down, removing loose dirt or dust and applying two coats of synthetic enamel paint over prepared old surfaces of steel complete all as specified and as directed by the Engr-in-charge.

M&L for preparation of old wooden surfaces of any description not other wise decribed over 10 cm width or girth by scrubbing down, removing loose dirt or dust and applying two coats of synthetic enamel paint over prepared old wooden surfaces complete all as specified and as directed by the Engr-in-charge.

M&L for cutting of tree from wall or roof of building n.exc 10 cm girth, taking out tree trunk portion including root completely from wall/roof, digging out roof and making good disturbed surface with brick work in cement mortar 1:4 or filling PCC 1:2:4 type B1 using 20mm stone aggegate to match the surface as per eixsting complete as directed by Engineer-in-Charge.

M&L preparation of new surfaces of wooden of any description not other wise decribed over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by the Engr-in-charge.

M&L preparation of new surfaces of steel of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed by the Engr-in-charge.

M&L preparation of new/old plastered surfaces and applying texture paint including a layer of 3mm thick wall care putty in two or more coats for making smooth surfaces complete all as specified and as directed by the Engr-in-charge.

S & F in repair mild steel powder coated wooden finish curtain rod 25mm dia fixed with decorative brackets ,stop roller and glass at the end etc complete all as specified and as directed by the Engr-in-charge.

S & F of 15mm size PVC connections with PTMP nuts at both ends of length 600mm complete all as specified and as directed by the Engineer-in-Charge

M&L Cutting chases ,pinning in making good to facing where required and pointing in CM 1:3 to edges of landing , steps , cills , sunshades, shelves , lintel etc. and cutting chases for concealed water tubing etc and making good cutting n. exc 10 cm girth complete all as specified and as directed by the Engr-in-charge.

M & L for 15mm bore `Medium grade` GI tubing with all fitting and fixed complete to walls and ceilings or laid in floors including taking down existing tubing complete all as specified and as directed by the Engineer-in-Charge

M & L for 20mm bore `Medium grade` GI tubing with all fitting and fixed complete to walls and ceilings or laid in floors including taking down existing tubing complete all as specified and as directed by the Engineer-in-Charge

S&F in repair bib taps long body 15mm dia cast copper alloy Chromium Plated, fancy type screwed down for iron pipe and fixed complete all as specified and as directed by the Engr-in-charge.

S & F fancy type Pillar Tap of 15mm bore, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed by the Engineer-in-Charge.

M & L for 75mm bore PVC (SWR) multi-floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed by the Engineer-in-Charge

S & F in repair 15mm bore stop valve, fancy type cast copper alloy chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair for 15mm bore stop valves, fancy type cast copper alloy chromium plated with long shank and cup (concealed) type complete all as specified and as directed by the Engr-in-charge.

S & F brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed by the Engineer-in-Charge

S&F in repair chromium plated shower rose 125 mm size with or without swivel joints any size including to fixing to steel pipe or union complete all as specified and as directed by the Engr-in-charge.

S&F in repair viterious china white wash hand basin with pedestal white in colour ISI marked of size 550mm x 400mm with brass chromium plated waste coupling and PVC waste pipe fixed to walls with CI breckets 2 Nos embedded in CM 1:4 type complete all as specified.

S&F in repairs viterous china squatting pan Orrisa pattern size 580 x 440mm white with "P" and "S" trap and integral foot rests including connectipon to trap and to flishing pipe , anti syphonage pipe etc incl provisioning of lime concrete complete all as specified and as directed by the Engr-in-charge.

S&F in repairs 10 ltr PVC valveless syphonic action type flushing cistern with brackets, flush pipe etc complete including inlet ball valve float and handle including brackets of approved make including all connections & flush pipes for WC complete all as specified and as directed by the Engr-in-charge.

S&F in repair vitreous china wash down water closet pan ( pedestal pattern) white including connection to out going pipe and to flushing pipe and antysyphonic pipe etc including plastic water closet white, closet pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device complete all as specified and as directed by the Engr-in-charge.

S&F in repair brass chromium plated toilet paper holder complete fixed to wall complete all as specified and as directed by the Engr-in-charge.

S & F for galvanized mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified and as directed by the Engineer-in-Charge.

All as per item No 1.38 above but in repair, complete all as specified and as directed by the Engr-in-charge.

S&F for in repair stainless steel sink with out drainage board made of stainless steel 1 mm thick sheet for kitchen with brass chromium plated waste coupling , waste pipe , washer and including all necessary item including fixing to brackets and connected union to pipe complete of overall size 495 x 420 mm with bowl size 410mm x 330mm x 160mm complete all as specified and as directed by the Engr-in-charge.

S&F in rep plastic water closet seat white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinges device complete all as specified and as directed by the Engr-in-charge.

S&F in repair for 6mm thick looking mirror of size as required with bevelled edge fixed with CP nuts and screws complete all as necessary items complete all as specified and as directed by the Engr-in-charge.

S&F in repair brass CP wall mixer for mixing hot & cold water for 15mm bore, pipes, screwed down for iron pipe and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair brass CP WHB mixer for mixing hot & cold water for 15mm bore, pipes, screwed down for iron pipe and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair brass CP Single towel rack 600 mm long between flanges including brackets complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair brass CP SOAP DISH HOLDER including fixing with brass screws to wall complete all as specified and as directed by the Engineer-in-Charge.

S&F bib tap, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule for 15mm bore complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair 15 mm bore, brass chromium plated angle valve with wall flange complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair glass Shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 Cm wide, aluminum alloy brackets and guard railing 60 Cm long including fixing with brass screws to wall complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair white Vitreous china wash down water closet pan along with vitreous china flushing cistern, seat cover,hinges etc of WC size 800 x 365 x 650mm including trap as required complete all as specified and as directed by the Engr-in-charge. Note : The contractor shall produce warranty from manufacturer before claiming payments.

S&F in repair viterous china white table top wash hand basin with brass chromium plated waste coupling, waste pipe, PVC connection and all connected fittings complete all as specified and as approved by Engineer-in-Charge.

S&F brass CP Towel ring round with all connected fittings complete all as specified and as approved by Engineer-in-Charge.

S&F brass CP Hand shower (Health Faucet) with all connected fittings complete all as specified and as approved by Engineer-in-Charge.

S&F Vitreous china urinal, half stall type white (excluding flusing cistern, flush pipe) including PVC waste pipe , providing and fixing plugs bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing with brackets, flush pipe, grating and union for discharge pipe. fixed "as in repair" complete all as specified and as approved by Engineer-in-Charge.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick 1st quality (square/ rectangular) area of each tiles exc 0.11 but not exc 0.18 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or colour cement to match laid over and including 15mm cement screed bed in CM (1:4) including demolition of existing tiles complete all as specified and as directed by the Engr-in-charge.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick 1st quality (square/ rectangular) area of each tiles exc 0.11 but not exc 0.18 Sqm in skirting etc set and jointed in neat cement slurry and pointed in white or colour cement to match laid over and including 10mm cement rendering in CM (1:4) including taking down cement plaster complete all as specified and as directed by the Engr-in-charge.

M&L for light shade Double charged vitrified tiles joint free 10 mm thick (square/ rectangular) area of each tiles exc 0.36 Sqm but not exc 1 sqm in floor etc set and jointed in neat cement slurry and pointed in white or colour cement to match laid over and including 15mm cement screed bed in CM (1:4) including demolition of existing tiles complete all as specified and as directed by the Engr-in-charge.

M&L for light shade Double charged vitrified tiles joint free 10 mm thick (square/ rectangular) cut from area of each tiles exc 0.36 Sqm but not exc 1 sqm in skirting etc set and jointed in neat cement slurry and pointed in white or colour cement to match laid over and including 10mm rendering in CM (1:4) including demolition of existing tiles complete all as specified and as directed by the Engr-in-charge.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc & brushing with neat cement slurry with 3 Kg of cement per Sqm Complete all as specified and directed by the Engineer-in-Charge

M&L for glazed coloured ceramic tiles 1st quality in vertical surfaces such as skirting /dados and riser to steps area of tiles 350mm x250mm x7mm/450x350x7mm thick set and jointed and pointing in white or coloured cement to match over and including 10 mm thick plaster in CM 1:4 including demolition of existing tiles complete all as specified and as directed by the Engr-in-charge.

M&L for 16 to 18 mm thick MDF board prelaminated MDF board , exterier grade (grade-1) confirming IS 14587, fixed with screws for kitchen cupboard and cabinet ,self for cupboard including hinges , brass handle and all necessary items complete all as specified and as directed by the Engr-in-charge.

M & L for 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed by the Engineer-in-Charge

S&F for II class HW 35 mm thick plain framed panelled shutter( two panel) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on boths face . The size of rail and style as per IS:1003 (part-1) kiln seasoned and chemically pressure treated and making good to distrubed portion with match the existing surfaces including taking down existing shutter complete all as specified and as directed by the Engr-in-charge.

S&F for 35 mm thick II class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass , gauze etc. (with out sash bars) ,edges of framing plain chamfered or rounded , fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I, Section-8, clause 8.24 (a) (wood used in this item shall be kiln seasoned and chemically pressure treated) and making good distrubed portion with existing including taking down existing shutter surface complete all as specified and as directed by the Engr-in-charge.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm prelaminated PVC sheet, reinforced with M.S. square tube and fixing in opening as per specification & drawing including taking down existing Chowkhat complete all as specified and as directed by the Engineer-in-Charge

S&F factory made solid PVC moulded door shutters with partical board core 28 to 30 mm thick (styles) with 2, 4, or 6 raised panel design with 2 mm thick prelaminated moulded PVC sheet on the front face and 2mm thick plain colour PVC sheet on back face fixing in frame at site as per specification and drawing including taking down existing shutter complete all as specified and as directed by the Engr-in-charge.

S & F double action floor spring, hydraulically regulated, made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and as directed by the Engineer-in-Charge

M&L for 12 mm thick prelaminated partical board interior grade prelaminated both side with decorative choice lamination fixed with screw to timber frame work/aluminium frame work complete all as specified and as directed by the Engr-in-charge.

S & F 100mm long mortice latch with two levers (vertical type), mild steel body complete all as specified and as directed by the Engineer-in-Charge

S&F for powder coated aluminium frame / shutter for door, window, ventilator, partition with one or more rebats including joint cleat, glazing clips, snap beading, rubber packing and all necessary items including taking out existing shutters complete all as specified and as directed by the Engr-in-charge. Note:- for payment purpose, only weight of aluminum works shall be measured and paid.

M&L for repairing of all type aluminium window/door shutter with frame and refixing it after resecuring its frame work by means of tightening with new screw or by new frame ,cleats and refixing in the same opening complete all as specified and as directed by the Engr-in-charge. (New aluminum frame shall be measured and paid for separately)

M&L for 5mm thick tinted glass fixed to aluminium frame including rubber bead complete all as specified and as directed by the Engr-in-charge.

S&F for framed work as in door of angle or other section with gusset plate , rails , braces, etc complete drilled for fixing of steel sheeting or other covering. Door etc, to be prepared hanging or sliding with and including either hooks and hinges or steel hanging door fitting and hanging also fastening and fixing including one shop coat of zink chromate primer paint confirming to Fe-410-W (Gde E-250) quality 'A' including removal of existing chowkhats complete all as specified and as directed by the Engr-in-charge.

PCC 1:3:6 type C-I using 20mm graded stone agg as in holdfasts, complete all as specified and as directed by the Engr-in-charge.

Supply and fixing steel window box type using ERW hollow 'P' section comprising double frame for and including gauged and glazed Skelton shutter 30mm thick, jointed internally with flat iron 25x3mm complete including hinges, handle, tower bolts, stops, lugs, guard bars and painting etc. all as shown on drawing No. TD-219 sheet 1/3 to 3/3 and TD-220 sheet 1/3 to 3/3 as applicable complete including taking down existing windows of any size and description complete all as specified and as directed by engineer in charge. Note: (i) For the purpose of measurement and payment double shutter both glazed and gauzed with frames shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery and grill as shown on drgs. (iii) Glazing, wire mesh shall be measured and paid for separately.

S & F 150mm aluminium handles, cast type, anodised complete all as specified and as directed by the Engineer-in-Charge

S & F 200mm long aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed by the Engineer-in-Charge

Supply and fixing for ISI marked 250mm long aluminum alloy, anodized sliding bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloys to door shutter complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing for butt hinge ISI Marked 100mm size, medium weight, cold rolled mild steel complete all as specified and as directed by the Engr-in-charge.

S&F for mild steel 150 mm ordinary rat tail rod pattern springs including rollers and roller plate etc complete all as specified and as directed by the Engr-in-charge.

S&F for 32 mm dia PVC waste pipe for wash hand basin / Kitchen sink etc complete all as specified and as directed by the Engr-in-charge.

Replacement of existing unserviceable helical wire spring 8 gauge helical wire spring complete all as specified and as directed by the Engr-in-charge.

Overhauling, serviceing and realignment of rolling shutters any size including replacement of defective bearing and grinding of wheels for smooth movement of doors , replacement of clamps, bolts etc including cleaning, oiling and greasing of moveable parts and welding work complete all as specified and as directed by the Engr-in-charge.. Note :- Necessary arrrangement of crane/moveing ladder shell be made by the contractor.

Replacement of existing unserviceable mild wheel gear box with new wheel gear box of suitable for large size shutters having area more then 8 sqm incl handle as per existing size complete all as specified and as directed by the Engr-in-charge.

S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors including dismantling of existing pipes complete all as specified and as directed by the Engineer-in-Charge.

S & F 110mm bore PVC (SWR) bends of any radius, complete all as specified and as directed by the Engr-in-charge.

S & F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls including dismantling of existing pipes complete all as specified and as directed by the Engineer-in-Charge.

S & F 75mm bore PVC (SWR) bends of any radius, complete all as specified and as directed by the Engr-in-charge.

M & L for 1000 Litres rotational moulded polyethylene water storage tanks triple layer(cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including dismantling water tanks exc 500 but not exc 1000 litres complete all as specified and as directed by the Engineer-in-Charge

M & L for 500 Litres rotational moulded polyethylene water storage tanks triple layer (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including dismantling water tanks exc 250 but not exc 500 Litrescomplete all as specified and as directed by the Engineer-in-Charge

S & F 20mm dia Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and as directed by the Engineer-in-Charge.

M & L for sheet glass 3.0mm thick, ordinary quality and glazing with oil putty in square n exc 0.5 sq m in each pane complete all as specified and as directed by the Engineer-in-Charge

M & L in repair for sheet glass 3.0mm thick , ordinary quality and glazing with oil putty in square n exc 0.5 sq m in each pane including hacking out old glass pane complete all as specified and as directed by the Engineer-in-Charge

Dismantling Wall and ceiling boards (fibre pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed by the Engr-in-charge.

S&F Galvanised powder coated snap grid ceiling consisting of cross and tee section of size 24mm x 38mm and wall angle of size 15mm x 15mm including 15mm thick Microlook mineral fibre Board of size 600 x 600mm. The snap grid frame shall fixed to ceiling with supporting consisting of 4mm dia GI wire including clip complete as per manufacturer instructions and complete all as specified and as directed by the Engr-in-charge.

S & F hollow PVC wall lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and as directed by the Engineer-in-Charge

Demolition of Brickwork built in cement mortar including all quioins, arches, pillars etc complete all as specified and as directed by the Engineer-in-Charge.

M & L for brick work with sub-class `B` bricks old size, straight or curved on plan exceeding 6 metre mean radius built in CM 1:6 complete all as specified and as directed by the Engineer-in-Charge

S & F for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa having zinc coating 150 gsm (AZ 150) as in roof covering/cladding to wall, fixed with self tapping screws including taking out existing sheets all as specified.

S & F for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa having zinc coating 150 gsm (AZ 150) as in roof covering/cladding to wall, gutters fixed with self tapping screws including taking down existing sheets complete all as specified and as directed by the Engr-in-charge.

Dismantling wooden scantling of any description not otherwise provided for complete all as specified and as directed by the Engineer-in-Charge.

S & F rolled mild steel work in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., quality confirming to Fe-410 W(Gde-E-250) quality 'A' complete all as specified and as directed by the Engineer-in-Charge

Demolition of Cement concrete (Unreinforced) of any description in ground floors and pavings n exe 15 cm thickness (below or above ground level) complete all as specified and as directed by the Engineer-in-Charge.

M & L for 75mm thick cement concrete 1:2:4 type B-2, using 40mm graded crushed stone aggregate as in sub base and finished even and fair without using extra cement complete all as specified and as directed by the Engineer-in-Charge

M &L 10mm thick coloured paver tiles (Endura Tiles) of size 300 x 300mm over and including a layer of 20mm thick screed bed in C.M 1 :4 joints filled with coloured cement to match the tiles , complete all as specified and as directed by the Engineer-in-Charge

M&L for cement concrete 1:2:4 type B-1 using 20 mm graded crushed stone aggregates as in cills, lintels, upto 1.50 metre clear span, copings, benching, bed plates etc. and in similar works including weathering, slightly rounded or chamfered angles and throating and necessary form works complete all as specified and as directed by the Engr-in-charge.

M&L for providing 50 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection laid in alternate bays (n exc 2 Sqm each ) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and as directed by the Engr-in-charge.

Sand filling under floor or in foundation including watering and consolidation complete all as specified and as directed by the Engr-in-charge.

M&L 60 mm thickness, M-35 grade, machine pressed precast concrete interlocking paver glazed finished coloured block any shape and size conforming to IS 15658-2006, set and jointed with grey cement and pigment complete all as specified and as directed by the Engr-in-charge.

Demolition of reinforced cement concrete in (other then ground floor) roofs , beams staircase , landing , chajja and similar suspended works reinforcement cut as required to facilitate demolition complete all as specified and as directed by the Engr-in-charge.

M&L for pre cast cement concrete type B-1(1:2:4) using 20 mm graded stone aggregate as in landing cover slabs for man holes , landings, balconies canopies, deck slabs and in shelves and the like including formwork etc complete all as specified and as directed by the Engr-in-charge.

M&L for mild steel TMT bar 10 mm dia and over cut to lenth bent to shape required including cranking bending spirally for hopping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0,.9mm dia or screwing with clip etc complete all as specified and as directed by the Engr-in-charge.

Material and labour for 15mm thick cement plaster in cement mortar 1:4, finished even and smooth without using extra cement but mixed with water proofing compound @ 3% by weight of cement or as per manufacturer's instruction and applying one coat of hot bitumen of Gde 85/25 @ 1.20 Kg/Sqm laid over and including a coat of bitumen primer, @ 0.30 to 0.50 Kg/ Sqm complete all as specified and directed. Note:- Cost of WPC shall be deemed to be included in quoted rate of this item

Material and labour for filling of lean conc 1:7:12 type F2 in sunken portion using brick aggregates, complete all as specified and as directed by the Engr-in-charge.

Supplying and laying self finished bitumen felt for water proofing, glass fibre base grade-2 laid on bituminous primer complete all as specified and as directed by the Engr-in-charge.

M&L for broken bricks loose filling with aggregates of gauge 80 to 150 mm in soakage pits, soakage wells, complete all as specified and as directed by the Engr-in-charge.

Dismantling for bricks tiles or terracing tiles single layer in roofs complete all as specified and as directed by the Engr-in-charge.

Demolition for mud/mud phuska in roofs any thickness including plastering and leaping if any and cleaning the surfaces with wire brush complete all as specified and as directed by the Engr-in-charge.

M & L for providing cement concrete 1:2:4, Type B1 using 20mm graded crushed stone aggregate as in roof kerbs , mud stops or padding as in roof and finished even and smooth with out using extra cement but using water proofing compound @ 3% by weight of cement or as per manufacturer's instruction complete all as specified and as directed by the Engineer-in-Charge. Note:- Cost of WPC shall be deemed to be included in quoted of this item

ACCESSIBLE ROOF TREATMENTS :-APP TREATMENT WITH BRICK/PCC TILES :-M&L for providing and laying 3mm thick APP (atactric polypropylenepolymer) modified prefabricated five layer weight not less then 3.60 kg /Sqm water proofing membrane black finish reinforced with non woven polyster matt, make as approved consisting of a coat bitumious primer @ 0.40 ltr /Sqm by the same membrane manufactures of density 0.87 to 0.89 kg/ltr at 25'C temprature and viscosity 70-160 cps over the primer coat, the layer membrane shall be laid using butane troch and sealing all joints etc after preparing the surface complete as per standred practice as per manufactures instructions . The vital physical and chemical parameters of the membrane shell be under ;- (i) Joint strength in longitudinal and transverse direction at 23 degree celsius at 650/ 450 N /5 cms (ii) Tear strength in longitudinal and transverse direction at 300/250N/5 cms. Softing point of membrane not less then 150'C when tested in accordance with ASTM (d-5147) (iii) The laying of membrane shell be got down through the authorised applicator of manufactures of membrane only .

M&L for 40 mm thick brick tiles laid in CM(1:6) 15 mm thick and jointed flush in CM (1:3) mixed with 5% crude oil by weight of cement complete all as specified and as directed by the Engr-in-charge.

Swami Enterprises

Sham Sunder Bansal

S M BUILDERS

RONKI RAM AND COMPANY

M/s B.S.Jain

Karishan Kumar goel

bhagwandasswazirchand