Supply of Lab Equipment_EE_DCESL

DUAL TRACE CRO 30MHZ 30 MHz, 2 channel, Dual Trace CRO BW: DC to 30 MHz Sensitivity : 1 mv/div Vertical Deflection: Dc to 30 MHz, Modes: CH1, CH2, ADD DUAL(CHOP/ALT) Deflection factor: 5 mv/div to 5 v/div to 1 mv/div(X 5 mag on) Accuracy : +/-3% i/p impedance : 1 MΩ/25f Max.i/p voltage : Direct 250 V(DC +peak) i/p coupling: AC, GND, DC Rise Time : 8.8 ns or less CH1 out 20 mv/div into 50Ω : DC to 10 MHz Polarity inversion: CH2 only Horizontal Deflection: Display modes: A, A int B, B, TRIG-D, X-Y Time Base A : 0.2 µ/div to 20s/div in 19 calibrated steps of 1-2-5 sequence Hold Off Time: Variable with hold off control Time Base B : 0.2 µ/div to 20s/div in 7 calibrated steps of 1-2-5 sequence Delay sweep position: 1 div or less – 10 div or more. Sweep magnification : 10 times(max sweep rate 20ns/div) Accuracy : +-3%

FUNCTION GENERATOR ( 3MHz) Output Waveforms Sinusoidal, Triangle, Square, Ramp, Pulse, TTL (Sync) & DC Outputs.Frequency Range 0.01Hz to 3MHz in 8 decade ranges.Frequency Indication ±1% ±1 digit.Frequency Indication Accuracy ±1% +1 digit,Sine Distortion <1% .Output Impedance 50 ohms,Frequency Stability <0.5% of the set frequency,Square Wave Rise / Fall Time <75nsec. Duty Cycle 10% to 90% variable.Maximum Output Voltage: Into 50 ohms 10V p-p output ,Open Circuit 20V p-p output.Amplitude Indication 3 digit seven segment display (Vpp) ±5%.Amplitude Flatness ±0.5dB upto 100KHz range / ±1.0dB for 1MHz range.Attenuator Two step attenuators of 20dB & 40dB. Fine attenuation of 20dB through vernier control. (Total 80 dB attenuation).Attenuator Accuracy ±0.5dB per 20dB at 1KHz.DC Offset ±10V ±5% (DC + AC peak) in open circuit ±5V ±5% (DC + AC peak) in 50 ohms.

Digital IC Trainer 10 logic switches, 10 logic lamps, 4-7 segment displays, +5 V, +/- 12 V, mono clock, fixed clock 1Hz, 10 Hz, 100 Hz, 1 KHz, 1 MHz, 2 nos. of ZIF sockets( 20 pin ), bred board with 1680 tie points and logic probe.

DIGITAL STORAGE OSCILLOSCOPE 100Mhz,Dual Channel,Colour Display, Bandwidth-DC~100Mhz(-3db),Rise time 5ns ,Bandwidth limit~20Mhz, Input coupling-AC, DC,GND Polarity-Normal & invert, Maximum input voltage: 300Vrms Vertical Sensitivity resolution -8 bit: 1mv~10v/div , Input Impedance~1MΩ DC gain accuracy-±3% Trigger mode:Auto,Normal,Single sequence ,Trigger type:Edge,Pulse width,video,external, rise & fall, timeout, alternate, Sensitivity:1 div, Event-delay(1~65535 events), time delay(duration~4ns~10s),Holdoff range:4ns~10s External Trigger Range:±15V Sensitivity:~100mv Input impedance:1MΩ Horizontal Time base range:5ns/div~100s/div Roll:100ms/div~100s/div ,Pre-trigger:10div maximum ,Post-trigger:2000000div maximum Time-base accuracy:±50ppm over any ≥ 1ms time interval ,Real time sample rate:1GSa/s maximum ,Record length:~10Mpts, Acquisition mode:Normal,Average,Peak detect,Single ,Peak detection:2ns ,X-Y mode phase shift:~±3° Cursors:Amplitude,Time,gating Unit:second, Hz(1/s), phase(degree), ration(%) automatic measurement:36 sets:pk-pk,max,min, amplitude,high,low,mean,cycle mean,rms,area,cycle area, rovshoot,fovshoot,rpreshootfpreshoot,frequency,period,rise time,fall time,positive width,negative width, duty cycle, positive pulse,negative pulses,+edges,-edges,FRR,FRF, FFR, FFF, LRR, LRF, LFR, LFF, phase

DIGITAL MULTIMETER Digital Multimeter with 3 ½ digit LCD Display DC Voltage : 0 – 200mV/2V/20V/200V/1000V AC Voltage : 0 – 200mV/2V/20V/200V/750V Dc Current : 0 – 200uA/2/20/200mA/10A AC Current : 0 – 200uA/2/20/200mA/10A Resistance : 0 – 200/2k/20k/200k/2000K/20M/200Mohms Diode test, hfe test, and audible continuity test facility

Bread Board 1680 tie points

DC Regulated Dual Power Supply (0 - 30) V,2A (0 - 30) V,2A. Continously variable by coarse and fine knobs. Metering : 3 digit DPMs for Voltage & Current Ripple & Noise : Less than 2mV rms Protection : Against Over Load & short CKT

D/A interfacing card Two numbers of DAC 0800 x Analog Output: +5V to -5V x DAC outputs are terminated at a suitable connector available on*board x Provision for test points & fault analysis points * All Address, data and control lines are terminated in a 50 Pin FRC OEN "make male connector to interface with VXT bus * 50 Core Cable provided

A/D interfacing card Incorporates one number or ADC 0809 * Start of Conversion by manual switch or software * End of Conversion (EOC) monitored through Interrupt / Polling * Display of digital data using LED's * All the 8 channel analog inputs terminated at Screw type connector. * Trimpot is provided on-board to channel 0 or 3or6 * Provision for test points & fault analysis points x 50 Core Cable provided * All Address, data and control lines are terminated in a 50 Pin FRC OEN Make male connector to interface with VXT bus

Arduino Uno Arduino Uno R3 ATmega328P ATMEGA16U2 Compatible with USB Cable

8086 trainer kit 16*2 lcd display CPU 8086 (16 BIT PROCESSOR) -CLOCK 6.144 MHZ KEYBOARD PS/2, IBM -COMPATIBLE -DISPLAY 16* 2 LCD MODULE RAM 16KB (6264 *2) -EPROM 16KB (2764 *2) -IO LINES – 48 LINES USING 2 NOS OF 8255 -TIMER/COUNTER 8253 -INTERRUPT CONTROLLER 8259 -INTERFACE UART(8251) BUS50 pin FRC (TTL COMPATIBLE) -INPUT SUPPLY 230V,A.C, 1 PHASE, +/10%, 50 HZ -DC SOURCE + 5V ,1 AMPS;+/12V

Synergy Technical Systems

innovative instruments inc

LINMA

Scientech Technologies Pvt Ltd

BARATHI ENTERPRISES