REPAIRS TO FURNITURE OF MD OTM ACCN AT LL UNDER GE ARMY BARODA

Amount

NOTE: (i) for Replacement, the Size and shape of components of furniture shall be all as per Drg, Specified & directed. (ii) For wooden components replaced shall be 2-3 coats french polished & existing unreplaced components also polished with one coat to match full article furniture & For steel components replaced shall be two coat of syntheic enamel paint over red oxide primer & existing unreplaced components painted with one coat synthetic enamel paint to match full article furniture.. (iii) The article of furniture shall be stacked inside godown neatly after complete repairs. (iv) Teakwood shall be Ist class well seasoned (v) The rate shall be quoted under respective items accordingly. M&L for removing existing unserviceable cane from Chair and recanning / reweaving with the plastic cane 2 mm wide & border with 4mm wide cane of approved quality complete for following chairs : NOTE: (a) Canning shall be "Godrej Pattern" (b) The cane shall be of make: "AJAY/MPI/SHAH/GARWARE or equivalent"

Chair Dining

Chair Writing

Chair easy

Chair Easy FD-229 : Dismantling the following UNSV components and S&F new components using 1st class teak wood duly french polished to match to existing with size & shape all as per drg, specified & directed and stacking of furniture inside the godown after repairs etc. complete.

Front Legs

Rear Legs

Side Rails

Front and Back rails

Back seat side rails

French Polish to existing unreplaced components.

Chair Dining (FD-228) : Dismantling the following UNSV components and S&F new components as specified, using 1st class teak wood duly polished to match to existing with size & shape all as per drg, specified & directed and stacking of furniture inside the godown after repairs etc. complete.

Front Legs

Rear Legs

Front Side Rails

Back Batten

Stiffener

French Polish to existing unreplaced components.

Chair Wooden Bottom (FD - 225) :- Dismantling the following UNSV components and S&F new components / Parts as specified complete.

Seat made of plywood 6mm thick.

Front legs.

Rear legs.

Side Rails for seat frame.

Front and back rails for frame.

Back batten.

Stiffener.

French polishing to old surfaces of chair wooden bottom to match with the existing complete.

Repair to Chair Dining MAP (DRG NO FD/E6/MAP/II/04) : Dismantling the following UNSV components and S&F new components / Parts as specified complete.

Bottom 6mm plywood for chair dining MAP.

Provide of Polyurethene foam 75mm thick ( 32Kg density) for seat of chair dining MAP and covered with Leatherit of best quality and colour as approved.

Scrubed and cleaned old patchy / dirty surface of furniture article and french polished in desired shade with high glossy finish and best workmanship.

Chair Writing (FD-280) : Dismantling the following UNSV components and S&F new components / Parts as specified complete.

Front Legs

Rear Legs

Side Rails

Front and Back rails

Stiffener

French Polishing to old surface of Chair writing to match with new & existing complete.

Table(3x2) 900x600x760 with drawer FD-283: Dismantling the following UNSV components and S&F new components / Parts as specified complete.

Top 18mm thick both side pre-laminated MDF board exterior grade with 6mm thk beading of 1st class hard teak wood.

Drawer made of well seasoned 12mm thick teakwood planks and bottom of the drawer shall be of 6mm thick plywood BWR grade.

Legs made of well seasoned Teakwood

Long Rails made of well seasoned Teakwood

Short Rails made of well seasoned Teakwood

Stiffner made of well seasoned Teakwood

French Polishing to old surface of table 3x2 with drawer to match with new & existing complete.

Table (3x2) 900x600x760mm w/o Drawer FD-284 : Dismantling the following UNSV components and S&F new components / Parts as specified complete.

Top 18mm thick both side pre-laminated MDF board exterior grade with 6mm thk beading of 1st class hard teak wood.

Legs made of well seasoned Teakwood

Long Rails made of well seasoned Teakwood

Short Rails made of well seasoned Teakwood

Stiffner made of well seasoned Teakwood

French Polishing to old surface of table to match with new & existing complete.

Table (3x3) 900x900x760mm (FD-88M & FD-291) : Removing following unserviceable items of table 900x900mm and S&F with new items as specified.

Top 18mm thick both side pre-laminated MDF board exterior grade with 6mm thk beading of 1st class hard teak wood.

Front Rails made of well seasoned Teakwood

Side Rails made of well seasoned Teakwood

French Polishing to old surface of table dining eight person to match with new & existing complete.

Table Bed Side (FD-276) : Dismantling the following UNSV components and S&F new components / Parts as specified complete.

Top/bottom 18mm thick both side pre-laminated MDF board exterior grade with 6mm thk beading of 1st class hard teak wood.

Sides made of Top 18mm thick both side pre-laminated MDF board exterior grade with 6mm tk beading of 1st class hard teak wood around front side.

Shelves made of 12mm thick MDF board with pre laminated particle board exterior grade with 6mm thk beading of 1st class hard wood teak around side.

Back with 6mm thick commercial plywood.

French Polishing to old surface of table Bed side to match with new & existing complete.

Peg Table (FD-277) Removing following unserviceable items and S&F with new items as specified.

Top 18mm thick both side pre-laminated MDF board exterior grade with 6mm thk beading of 1st class hard teak wood.

Legs made of well seasoned Teakwood of best quality

Long Rails made of well seasoned Teakwood

Stiffener made of well seasoned Teakwood

French Polishing to old and new surface of Peg table to match with new & existing complete.

Bed Ply Top (Drg No FD-246/247) : Dismantling / Removing the following existing UNSV parts / components as specified and S&F new components, using 1st class teak wood duly polished to match to existing with size & shape all as per drg, specified & directed and stacking of furniture inside the godown after repairs etc. complete.

12mm thick BWR plywood commercial fixed with screws complete.

Head Top made of well seasoned TW of best quality

Foot Board made of well seasoned TW of best quality

Long Rails made of well seasoned TW of best quality.

Short Rails made of well seasoned Teakwood of Ist quality.

French Polishing to old surface of Bed Ply top match with new & existing complete.

Teapoy Wooden (FD-278) : Dismantling the following UNSV components and S&F new components / Parts as specified complete.

Top 18mm thick both side pre-laminated MDF board and exterior grade with 6mm thk beading of 1st class hard teak wood.

Long Rails made of well seasoned Teakwood

Short Rails made of well seasoned Teakwood

French Polishing to old surface of teapoy to match with new & existing complete.

Table Dining 6 Person (FD-273) : Dismantling the following UNSV components and S&F new components / Parts as specified complete.

Top 18mm thick both side pre-laminated MDF board exterior grade with 6mm thk beading of 1st class hard teak wood.

Legs made of well seasoned Teakwood

Long Rails made of well seasoned Teakwood

short Rails made of well seasoned Teakwood

French Polishing to old surface of table dining six person to match with new & existing complete.

Table Centre (DRG NO FD-274) ; Dismantling the following UNSV components and S&F new components / Parts as specified complete.

Legs of Ist class hardwood (teakwood)

Long rail of Ist class hardwood (teakwood)

Short rail of Ist class hardwood (teakwood)

Top made out of 18mm thick prelaminated particle board interior grade with 6mm thk beading of 1st class hard teak wood..

Scrubed and cleaned old patchy / dirty surface of furniture article and french polished in desired shade with high glossy finish and best workmanship.

Table writing (DRG NO FD-249/275) ; Dismantling the following UNSV components and S&F new components / Parts as specified complete.

Legs of Ist class hardwood (teakwood)

Side rail long of Ist class hardwood (teakwood)

Siderail short of Ist class hardwood (teakwood)

Top made out of 18mm thick prelaminated both side of MDF board with pre polished teakwood 6mm thk lipping.

Scrubed and cleaned old patchy / dirty surface of furniture article and french polished in desired shade with high glossy finish and best workmanship.

Repair To Table Dining 1200 x900mm (FD/MAP-II/03) : Removing / Dismantling the following unsv part / component and providing new components / parts complete.

Top with 18mm thick prelaminated both side of MDF board with pre polished teakwood 6mm thk lipping.

Legs of Ist class hard wood (Teakwood)

Long rail of Ist class hard wood (Teakwood)

Short rail of Ist class hard wood (Teakwood)

Dismantling / Removing old unsv tapestry cloth from foam cushion of size 560 x 530 x 100mm and covering the same foam cushion with new tapestry cloth of approved colour & texture, followed by stitching with white linen and shall be of removable type by providing plastic zip over tapestry cloth cover complete. Note:Tapestry cloth shall not be less than Rs 250/- per meter of standard width.

S&F in replacement synthetic cushion of existing size of 32 density cool foam for seat and back including covered with tapestry cloth of approved colour and texture for cover of cushion and shall be of removable type by providing plastic Zip over Tapestry cloth cover complete. Note: Tapestry cloth shall not be less than Rs 250/- per meter of standard width.

Repairs to Locker bed side steel (FD-1029) : Dismantling / removing the following UNSV components and S&F new components / Parts as specified complete.

Socket for hanging CP rod 20mm dia

Hasp & staple of 75mm x 40mm x 3mm

Shutter of Locker Bed side steel duly painted.

Shelves of locker bed side steel duly painted..

Legs of locker bed side steel of U shape chennel 10mm height & 60mm wide ends plugged with 1mm thick mild steel sheet duly welded at both duly painted.

CP pipe 20mm dia CP steel conduit pipe of 1.6mm thickness

M&L for preperation of old surfaces of locker bed side steel & puttying where required and apply one coat of synthetic enamel OG/Gray paint including welding where required.

Chair Verandah steel FD 256 : Dismantling / removing the following UNSV components and S&F new components / Parts as specified complete.

Leg frame of size 20mm dia 16 gauge of MS conduit pipe fixed with run welding & duly painted and hard rubber shoe.

Plastic cane weaving 2mm wide border 3.5/4mm wide round side border cane of approval qty after applying one coat of synthetic enamel white paint complete. make of cane: Ajay / MPI / Shah / Garware

Hard rubber shoe.

Almirah Med Steel FD-1032 : Dismantling / removing the following UNSV components and S&F new components / Parts as specified complete.

Handles Stainless Steel

Locking device

Leg duly painted.

Shutter of 1.0mm thick MS duly painted with two coat of synthetic enamil paint OG/Grey over a coat of redoxide

M&L for preperation of old surface of almirah steel & puttying where required and apply one coat of synthetic enamel OG/Gray paint including welding where required.

Charpoy GI Pipe ply top (FD-220) : Dismantling / removing the following UNSV components and S&F new components / Parts as specified complete.

Tightening / refitting of frame by removing plywood top from charpoy GI with all fittings complete.

Plytop of 12mm fit to size including 6mm dia 65mm long bolt round headed, with nut and washer maximum 10 Nos per charpoy.

Stiffener of size 25mm square conduit pipe of 1.6mm thick welded at equal distance of GI charpoy frame and applying two coats of synthetic enamel black paint over a coat of red oxide primer to conduit pipe.

GI elbow (32mm dia) ISI marked three way medium grade.

GI checknut 32mm dia medium grade.

32mm dia medium grade long rail including cutting, threading for GI Charpoy (Note: Long Rails are screwed fully in the angle elbow)

Short rails for GI Charpoys 32mm dia made out of from broken long rails obtained from srl item No. 22.06 above including cutting & threading rails and fixing. (Note: Short Rails are screwed fully in the angle elbow)

Legs for GI Charpoys 32mm dia made out from broken short rails obtained from Srl item No. 22.07 above including cutting, threading and fixing and providing of 5mm thick MS Plate of dia 50mm at bottom of legs by welding duly painted with two coat of synthetic enamel black paint. (Note: Legs are screwed fully in the angle elbow)

Table Bed Side MAP(FD-E6/MAP/15® : Dismantling / removing the following UNSV components and S&F new components / Parts as specified complete.

Side of table with Particle Board Prelaminated both side 18mm thick exterior grade (ISI Marked) with hot pressed beading.

Top of table made out of particle Board Prelaminated both side 18mm thick exterior grade (ISI Marked) with hot pressed beading.

Upper drawer of Table made out of Particle Board Prelaminated both side 18mm thick exterior grade (ISI) Marked duly fixed with hot pressed beading.

Lower Drawer of Table made out of Particle Board Prelaminated both side 18mm thick duly fixed with hot pressed beading, rest all as shown in drg and as directed.

Back side of Table made out of 12mm thick Ply Wood BWR Grade (ISI Marker).

MS Tube frame of Table made out of 18 x 18 mm, 18 Gauge MS Square Pipe duly painted.

Copper oxidised steel handle for Table Bed Side MAP.

Almirah Large Steel (FD-67(M), FD-1031, FD-1033, FD/E6/MAP/18 : Dismantling / removing the following UNSV components and S&F new components / Parts as specified complete.

Shelves made out of 1mm thick MS sheet bent to shape & cut to size duly painted.

Legs made out of 1.00mm thick MS sheet bent to shape & cut to size duly painted.

Locking device three way made out of 10mm MS bar round and 3mm MS plate.

Handle with bush to almirah large steel.

Lock to almirah large steel.

Cleats made out of 2mm thick sheet bent to shape, fixed with nut & bolt to give support to shelves duly painted.

Coat of synthetic enamal paint OG/Smoke Gray to internal / external surface & shelves completely strictly through spray gun machine after preparation of old painted surface by filling with putty, cleaning with sand paper and applying primer where required to Almirah Large Steel.

Teapoy Varandah (FD/E6/MAP/17 & FD-255, FD-383) : Dismantling / removing the following UNSV components and S&F new components / Parts as specified complete.

Top made out of Particle Board Prelaminated both side 18mm thick exterior grade (ISI marker) and PVC hot pressed beading all around the top of same color.

One coat of synthetic enamal paint Black / White to Teapoy Varandah after preparation of old painted surface by filling with putty, cleaning with sand paper and applying primer where required.

Bin Soiled Linen Multipurpose (FD/E6/MAP/09) : Dismantling / removing the following UNSV components and S&F new components / Parts as specified complete.

Top of Bin Linen Multipurpose made out of Particle Board Prelaminated both side18mm thick (ISI Marked) duly fixed with hot pressed PVC beading.

Side purlin of Bin Linen Multipurpose made out of Particle Board Prelaminated both side18mm thick (ISI Marked) duly fixed with hot pressed PVC beading.

Shutter of Bin Linen Multipurpose made out of Particle Board Prelaminated both side 18mm thick (ISI Marked) duly fixed with hot pressed PVC beading.

Drawers made out ofParticle Board Prelaminated both side 18mm thick (ISI Marked) duly fixed with hot pressed PVC beading.

Bottom / Shelves of Bin Linen Multipurpose made out of Particle Board Prelaminated both side 18mm thick (ISI Marked) duly fixed with hot pressed PVC beading.

Back Support of Bin Linen Multipurpose made out of 12mm Commercial plywood.

Table Computer (FD/E6/MAP/03) : Dismantling / removing the following UNSV components and S&F new components / Parts as specified complete.

Top made out of 18mm thick prelaminated particle board exterior grade (ISI Marked) one side teak face & other side white with hot pressed PVC beading.

Key Board Tray (450 x 480mm) fitted with telescopic channel.

Pull out Tray fitted with telescopic channel.

Chair CBA Steel with Arms (FD-75(M)) : Dismantling / removing the following UNSV components and S&F new components / Parts as specified complete.

Flat iron 25 x 3mm of required length welded with seat of chair CBA steel with arms complete.

Factory made Seat made out of 2nd class hard wood teak (Well seasoned) duly black stove polished includng cane work 2mm plastic cane half rounded and 3.5/4mm for perimeter work godrej pattren.

Factory made Back rest made out of 2nd class hard wood teak (Well seasoned) duly black stove polished includng cane work 2mm plastic cane half rounded and 3.5/4mm for perimeter work godrej pattren.

Arm rest made out of 1st class hard wood teak (Well seasoned) duly black stove polished.

M&L for one coat of synthetic enamal paint olive green to Chair CBA steel with arms after preparation of old painted surface by filling with putty, cleaning with sand paper.

Chair CBA Special with hand rest (FD-260 /FD/E6/MAP/05) : Dismantling / removing the following UNSV components and S&F new components / Parts as specified complete.

Factory made Seat made out of 2nd class hard wood teak (Well seasoned) duly french polished including cane work 2mm plastic cane half rounded and 3.5/4 mm for perimeter work godrej pattern.

Facory made Back rest made out of 2nd class hard wood teak (Well seasoned) duly french polished including cane work 2mm plastic cane half rounded and 3.5/4mm for perimeter work godrej pattern.

M&L for removing of unserviceable broken arms from existing Chair CBA Special Steel with hand rest and S&F new arms made out of 1st class hard wood teak (Well seasoned) Duly french polished fix with screw steel all as specified and directed.

Hand Rest made out of 1st class hard wood plank in one piece teak (Well seasoned) duly french polished fix with screw steel.

M&L for for one cot of synthetic enamal paint OG to Chair CBA Special with hand rest Steel after preparation of old painted surfaces by filling with putty, cleaning with sand paper.

Table office Clerk Steel (FD-84(M) & FD-1004) : Dismantling / removing the following UNSV components and S&F new components / Parts as specified complete.

Top made out of Particle Board Prelaminated 18mm thick (ISI Marked) with hot pressed PVC beading all around the top of same colour.

Drawers made out 1mm thick MS Sheet bend to shape & cut to shape duly painted.

Lock to Table

M&L for fine coat of synthetic enamal paint OG/Smoke Gray strictly with spray gun machine to all steel surface after prepration of old painted surfaces by filling with putty, cleaning with sand paper.

Chair Computer (FD/E6/MAP/01) : Dismantling / removing the following UNSV components and S&F new components / Parts as specified complete.

Side arms (PU Material) fixed to chair Computer.

Factory made Cushion seat made of 12mm thick hot pressed plywood upholstered with fabric and moulded polyurethane foam with PVC lipping all round.

Factory made Cushion Back made with 12mm thick hot pressed plywood upholstered with fabric and moulded polyurethane foam with PVC lipping all around.

Base assembly to chair computer.

Hydraulic assembly to chair Computer.

Caster wheel.

Chair Writing (FD/E6/MAP/12) : Dismantling / removing the following UNSV components and S&F new components / Parts as specified complete

Side Arms (PU Material) fixed to chair writing.

Factory made Cushion seat made with 12mm thick hot pressed plywood upholstered with fabric and moulded polyurethane foam with PVC lipping all round.

Factory made Cushion Back with 12mm thick hot pressed plywood upholstered with fabric and moulded polyurethane foam with PVC lipping all around.

Table Office Officer Steel (FD54(M) & FD-1003) : Dismantling / removing the following UNSV components and S&F new components / Parts as specified complete

Top made out of particle Board Prelaminated both side 18mm Thick (ISI Marked) with hot pressed PVC beading all around of same colour.

Drawers made out 1mm thick MS Sheet bend to shape & cut to size.

Shutter of side unit made out 1 mm thick MS Sheet bend to shape & cut to size.

Lock for existing table office clerk steel.

M&L for fine coat of synthetic enamal paint OG/Smoke Gray strictly with spray gun machine to all steel surface after prepration of old painted surfaces by filling with putty, cleaning with sand paper.

Table 3' x 2' Steel without Drawer (FD-1007) : Dismantling / removing the following UNSV components and S&F new components / Parts as specified complete

Top made out of Particle Board Prelaminated both side18mm thick exterior grade (ISI Marked) PVC beading fixed all around the top of same colour.

M&L for prepration of old painted surface by filling with putty, cleaning with sand paper & apply fine coat of sythetic enamal paint OG strictly with spray gun machine.

Table 3' x 2' Steel with Drawer (FD-1008) : Dismantling / removing the following UNSV components and S&F new components / Parts as specified complete

Top made out of Particle Board Prelaminated both side 18mm thick exterior grade (ISI Marked) PVC beading fixed all around the top of same colour.

Drawer made out of 1mm thick MS Sheet bent to shape & cut to size.

M&L for prepration of old painted surface by filling with putty, cleaning with sand paper & apply fine coat of sythetic enamal paint OG strictly with spray gun machine.

Table 3' x 3' Steel (FD-1009) : Dismantling / removing the following UNSV components and S&F new components / Parts as specified complete

Top made out of Particle Board Prelaminated both side 18mm thick exterior grade (ISI Marked) PVC beading fixed all around the top of same colour.

M&L for prepration of old painted surface by filling with putty, cleaning with sand paper & apply fine coat of sythetic enamal paint OG strictly with spray gun machine.

Table Dressing Gents with Mirror (FD-230) : Dismantling / removing the following UNSV components and S&F new components / Parts as specified complete

Looking mirror of Size 760 x 380 x 5.5mm thick duly framed made out of 1St class teak wood without crack and knots of Size 25 x 20 mm & 6mm thick commercial plywood on back and supported with batten 35 x 25mm.

Lower Box made out of Particle Board Prelaminated both side 18mm thk (ISI Marker) with hot pressed PVC Beading and back with 12mm Plywood.

Table Dressing Ladies with Mirror FD-251 : Dismantling / removing the following UNSV components and S&F new components / Parts as specified complete

Looking mirror of Size 1220 x 380, 5.5mm thick duly framed made out of 1st class teak wood without crack and knots of 25 x 20mm thick and 6mm thick commercial plywood on back of mirror and support with teak wood batten of Size 45 x 40mm.

Lower box except back made out of particle Board 18mm thk prelaminated both side with drawer and sliding channel with glass complete.

M&L for preparation of old polished / Painted surface of wooden furniture by removing dirt, spots, dots etc filling putty where required and polishing with ready made polish / painting with synthetic enamel paint as required shade of polish / paint shall be as directed for the following items of furniture

Hat stand with mirror (DRG NO FD -233/361

Book case (DRG NO FD -237/45/90)

Chair dining (DRG NO FD -279

Chair easy (DRG NO FD -229 & AS APPL)

Table centre (DRG NO FD -274 & AS APPL)

Chair writing (DRG NO FD -250 & AS APPL)

Table writing (DRG NO FD -3/275/249)

Table dining 6/8 persons (DRG NO FD -239/273 & AS APPL)

Teapoy (DRG NO FD -232 & AS APPL)

Table Bed side (DRG NO FD -248/28)

Bed plywood top

Peg table (DRG NO FD -236/277)

Stool dressing (DRG NO FD -252/27)

Side board (DRG NO FD -241)

Sofa set four seater single chair (FD-281/256)

Sofa set five seater (DRG NO FD -281/256)

Table dressing gents (DRG NO 230)

Table Dressing Ladies with Mirror (FD-251)

S&F knob for drawers and shutters of Table Writing, Table 3' x 2' with drawer, Dressing Table Ladies, Dessing Table Gents, Bin Linen Multipurpose and Side Boards etc. complete.

Badri Electricals