Annual maintenance of SV Rest house TTD buildings and temples at Gandhi road and GT mada streets etc for the year 2026 27

Collection and supply of good gravel for works from approved quarry to the site of work including cost and conveyance of all materials etc., complete as directed during execution.

Collection and supply of Quarry rubbish (35a) for works to the site of work including cost and conveyance of all materials etc., complete as directed during execution.

Supply of Common burnt clay bricks of class as per Table-1 of IS:1077-1992 Non-Modular of traditional size 23 x 11 x 7 cm to site of work.

Demolition of Brick work including stacking of serviceable materials and disposal of unserviceable materials within 100 meters lead etc., complete as directed during execution.

Demolishing of Unreinforced cement concrete up to 15cm thickness and disposal of unserviceable materials within 100 meters lead etc., complete as directed during execution.

Earthwork excavation for foundations and depositing on bank for all lifts and with an initial lead of 10m including all Operational, incidental ,labour charges such as shoring, sheeting, planking, strutting etc., complete for finished item of work. Ordinary soil-Manual means up to 3m depth.

Filling of foundations and basement with best river sand in layers of not more than 15 cms. thick each well watered to saturation and consolidated including cost and conveyance of all materials, incidental charges etc., complete.

Filling with useful available excavated earth (excluding rock) in trenches, sides of foundations and basement with initial lead in layers not exceeding 15cm thick, consolidating each deposited layer by watering and ramming including cost and conveyance of water to work site and all operational, incidental, labour charges, hire charges of T&P etc., complete for finished item of work. Note:- Cost of transportation of good quality earth has not been included. Only labour for carrying carted earth with a lead of 50m to the foundation pits has been taken in the rate. The cost of carted earth/sand may be worked out separately if the same is not available from adjoining area.

Conveyance of excavated surplus earth/debris to a distance of 4 to 5 KM from the work site of work at the place specified by the Engineer-in-charge including loading at site of work and unloading at the place specified by the department during execution.

Cement Concrete CC(1:2.5:5) - Grade M15 using 20 mm ( 0.54 cu.m) and 12 mm (0.36cu.m) nominal size hard broken granite crushed metal from any source conforming to the relevant ISI standards for foundations etc., laid in layers of not more than 15 cm thick well compacted including curing, ,machine mixing, cost and conveyance of all materials etc., complete. Note: Measurement boxes shall be used for measuring the quantities of cement, aggregate and water required for the given concrete mix.

Cement Concrete (1:4:8) using 40 mm ( 0.54 cu.m), 20mm (0.27 cu.m) and 12 mm (0.09 cu.m) nominal size hard broken granite crushed metal from any source conforming to the relevant ISI standards for foundations etc., laid in layers of not more than 15 cm thick well compacted including curing, ,machine mixing, cost and conveyance of all materials etc., complete.

Supply and placing of the M20 Design Mix using 10 mm HBG crushed metal 0.480 cum , 6mm HBG crushed metal 0.320 cum, sand 0.400 cum and cement 350 Kgs with water cement ratio of 0.53 (185.50 cum of CC) etc. from any source conforming to the relevant ISI standards including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seignoirage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as machine mixing, vibrating, laying concrete, curing etc., complete with minimum cement content as per IS code from standard suppliers approved by the department but excluding cost of centering charges and excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402) etc., complete as directed by the department Note: Measurement boxes shall be used for measuring the quantities of cement, aggregate and water required for the given concrete mix if mixing is done by volume mixing.

- do - for 50 mm thick precast slabs using 10 mm graded aggregate HBG crushed metal from any source conforming to the relevant ISI standards, with necessary reinforcement excluding cost of steel and tying of grills, centering charges, but including cost of necessary form work etc., complete as directed by the department.

- do - for drop 50 mm finished thickness with 10 mm graded HBG crushed metal from any source conforming to the relevant ISI standards with necessary reinforcement and chicken mesh etc. complete ,excluding cost of steel and tying of grills, but including cost of chicken mesh of not less than 30 Gauge necessary form work etc., complete as directed by the department.

Supplying and fixing of scaffolding to structure for various Civil repair works etc., including cost and conveyance of all materials such as Casurino Poles, Bamboos, country wood planks, nails and coir puri to provide working plot form along with ladder up to required level strongly. After completion of work scaffolding should be removed carefully as directed during the execution etc., complete. Note: The measurement for scaffolding should be allowed for one face only.

Providing High Yield Strength deformed (HYSD)/ Thermo mechanically treated (TMT) steel bars of High yield strength deformed bars below 36 mm Fe 500 (as per IS 1786 - 1979) of different diameters for RCC works, including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars including all wastages such as over laps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying including sales and other taxes on all materials etc., complete for finished item of work in all floors. (APSS NO.126) (In the absence of 18G binding wire, 2nos of 20G binding wire in tandem are to be strictly adhered).

Labour charges for fixing heavy iron grills, Trusses, Stanchions, Heavy Beams and Girders erecting in position and fixing by using chain pulley blocks, Derek pole arrangements and cranes etc., complete in position.

Supply and fixing of stainless steel SS-304 grade tubes, sections, plates , sheets and pipes of all sizes and diameters etc., including cost and conveyance of all materials and labour charges for fabrication of stainless steel railing works using SS welding rods including buffing , polishing , lacquer finishing , to present seamless finishing etc., complete as directed during execution

Labour charges for Fabrication of stainless steel railing works using stainless steel welding rods including buffing, polishing, lacquer finishing, to present seamless finish.

Random Rubble masonry Cement mortar (1:6) using granite stones from any source conforming to the relevant ISI standards including cost and conveyance of all materials, curing, packing, neat finishing etc., complete as per specifications (excluding cost of bond stones )

Construction of Brick Masonry in CM(1:6) using well burnt Bricks 2nd class or ground moulded (Non- modular or traditional size) (230 x 110 x 70 mm)including curing, cost and conveyance of all materials as directed during execution and complying with standard specifications etc., complete.

Construction of 110 mm thick brick partition walls in CM (1:4) using well burnt bricks 2nd class or ground moulded ( Non-Modular or traditional Size ) bricks (230x110x70mm) including curing , cost and conveyance of all materials etc., complete.

Plastering in Cement mortar (1:3) 12 mm thick using best river sand from approved quarry including cost and conveyance of all materials, screening, curing, rounding of corners, incidental charges as directed during execution complying with standard specifications etc., complete.

- do - (1:3) 12 mm thick.

- do - (1:5) 12 mm thick.

- do - (1:3) 20 mm thick.

- do - (1:5) 20 mm thick.

Flooring with Antiskid floor tiles 1st quality of all series & shades (as per manufacture specification), set over base coat of cement mortar (1:6) 20 mm thick over CC bed already laid or RCC roof slab, including white cement slurry of honey like consistency spread @ 3.30 kgs per sq.m. jointed with neat cement to full depth mixed with pigment of matching shade, including cost and conveyance of all materials like flooring slab, cement, sand and water etc., complete, for finished item of work) (Note: Unless otherwise laying of flooring is finished, no pre-payment shall be made for the tiles against supply)

Flooring with 1st quality Ceramic floor tiles of all series& shades (as per manufacture specification), set over base coat of cement mortar (1:6) 20mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.30 kgs per sq.m. jointed with neat cement to full depth mixed with pigment of matching shade, including cost and conveyance of all materials like flooring slab, cement, sand and water etc., complete, for finished item of work. (Note: Unless otherwise laying of flooring is finished, no pre-payment shall be made for the tiles against supply) '-do-1st quality polished marble series of size not less than 400 x 400 x 7.3 mm thick (Group B II of IS 15622 -2006, water absorption should be between 3 to 6%)

Finishing the sides of walls with Ist quality glazed wall tiles of following sizes of approved colour and brands including pointing the joints with the same colour of cement by mixing the same colour pigment in white cement and over a bed of C.M.(1:3), 12 mm thick & Cement slurry of 33 Kg/10sq.m shall be used for fixing bed tiles including cost and conveyance of all materials, curing, incidental charges etc., complete (No separate plastering shall be paid to the walls). 'Supply of glazed red or white full body ceramic wall tiles of size 200 x 300 mm / 245 mm x 325 mm and thickness 6 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs

Providing impervious coat to exposed RCC roof slab surface with CM (1:3), 20mm thick with 500 ml of liquid concentrated micronized cement water proof compound/ 100 ml of Integral cement water proofing admixture complies with IS:2645-2003 of approved make per 50 kg bag of cement laid over roof when it is green including cost of all materials, conveyance charges of materials and all operational, incidental and labour charges for mixing mortar, laying, rendering smooth and thread lining, curing, rounding off junctions of wall and slab etc., complete for finished item.

Providing weather proof course with Screeding concrete in CC(1:2:4), 25mm average thickness using 6 to 10mm nominal size HBG crushed metal chips, screeding duly embedding 24G chicken mesh with necessary overlap etc.., and finishing the surface neatly and rounding the edges at parapet walls, columns etc., including cost of chicken mesh, including cost of all materials and conveyance of all materials etc., complete as directed during execution.

Providing Unplasticized PVC SWR Rain water downfall pipes for the following dia with ISI:13592 Type -A mark with necessary shoes, bends, collars etc., including making holes in walls, RCC slabs, beams, columns, including fixing with necessary wooden plugs (where it is required pipe clear of wall, wooden blocks of size equal to that of ears of the pipe shall be used), screws, iron clamps of 18 G and making good the same including cost and conveyance of all materials and incidental charges etc., complete as directed during execution.

75 mm dia PVC pipe with wooden block of size 100mm x 50mm x 50mm

110 mm dia PVC pipe with wooden block of size 150mm x 50mm x 50mm

Supply and fixing of Galvalume sheet Pre-painted Galvalume Trapezoidal Profile Roofing sheets with 0.47mm thickness (Total Coated Thickness-TCT), Coating: Alu-Zinc coating AZ150 GSM. Tensile strength: 550 MPA. Paint coating: Regular Modified Polyester painting. Painting thickness (Top): 18 to 20 Microns, (Bottom): 5 to 7 Microns. Sheet Width: 1.020, Length: Maximum 12 Meters with Regular Range Colours with minimum end lap of 15 cms etc., complete as directed during execution (Original coil shall be of make TATA Blue scope/JSW)

Painting priming coat with ready mixed Cement primer (water thinnable) for plastered surface including cost and conveyance of all materials including brushes to have smooth finish as directed during execution.

- do - for interior grade - I for NEW WORK.

- do - for interior grade - I for OLD WORK.

- do - for Exterior grade - 2 for NEW WORK.

- do - for Exterior grade - 2 for OLD WORK.

Polishing for old wood work with best French Sprit polish of two or more coats of approved quality and make including brushes to have an even shade and including linseed oil, boiled, stopping cloth, cost and conveyance of all materials as directed during execution etc., complete.

Painting with Ready mixed Synthetic Enamel paint in all shades Grade-I having VOC (Volatile Organic Compound) content less than 50 grams/liter approved colour and make including brushes to have an even shade including cost and conveyance of all materials as directed during execution complying with standard specifications etc., complete.

- do - for OLD WOOD WORK.

- do - for old iron work & old plastered surface

Painting with Matt finish ready mixed paint of approved make and colour including brushes to have an even shade including cost and conveyance of all materials as directed during execution - Single coat for old work

Painting with Acrylic Emulsion paint interior grade having VOC (Volatile Organic Compound) content less than 50 grams/liter of approved brand and shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work as per SS 911 for internal walls.

- do - for Single coat for Internal walls - NEW

- do - for Single coat for Internal walls - OLD

- do - for TWO coats for Internal walls - NEW

- do - for TWO coats for Internal walls - OLD

Painting with Acrylic Emulsion paint exterior grade with silicon additives having VOC (Volatile Organic Compound) content less than 50 grams/liter of approved brand and shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work as per SS 911 for external walls.

- do - for Single coat for External walls - NEW

- do - for Single coat for External walls - OLD

- do - for TWO coats for External walls - NEW

- do - for TWO coats for External walls - OLD

Providing and applying wall putty of white cement or polymer or cement based putty of approved make with average 1 to 2 mm thickness over plastered surface to prepare the surface even and smooth after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, sand the surface, clean & wipe off loose dust, applying knifing paste filler by putty knife / muslin pad, air dry for 2-3 hrs. sand with 180 and 320 No., emery paper for the surface preparation including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work, excluding scaffolding charges - for internal and external walls.

- do - For New works

- do - For Old works

Supplying and fixing in position M.S Ornamental grills for windows and ventilators or for veranda openings using M.S. Flats, square rods, angles sheets etc., of approved design including necessary cuttings, bending fabrication, welding, grinding and finishing smooth including painting the grills with Two coats with Synthetic enamel paint Gr-I over a Primary coat (Red oxide metal primer) (total three coats) of approved make and colour including cost of making the holes into RCC or masonry works and making good the same wherever necessary, including cost and conveyance of all materials, incidental charges etc., complete.

Supply of the following materials / Accessories as and when required. The rate is inclusive of cost and conveyance other incidental charges.

- do - Kadapa slabs 40 mm thick and size not less than (0.457m X 0.457m) (BMT-B.01)

- do - G.I. wire 16 Gauge

- do - Turpentine.

- do - Fevicol / Wood adhesive compound

- do - Weld mesh with openings of size 75x25mm(7Gx11G)

- do - M.S.Sheets 18 Gauge

- do - M.S. Tubes & pipes of all diameters as per IS-1161

- do - M.S Angles, Channels and ' I ' sections.

- do - 5 Ply - 6 mm thick Plywood - IS 303 MOISTURE RESISTANT (MR) GRADE

- do - 5 Ply - 8 mm thick Plywood - IS 303 MOISTURE RESISTANT (MR) GRADE

- do - 9 Ply - 12 mm thick Plywood BWR/ BWP Grades - IS:303 (BOILING WATER RESISTANT).

- do - 9 Ply - 19 mm thick Plywood BWR/ BWP Grades - IS:303 (BOILING WATER RESISTANT).

- do - Anodised Alluminium tower bolts 10 mm dia x 75 mm long with ISI mark IS 204.

- do - Anodised Alluminium tower bolts 10 mm dia x 150 mm long with ISI mark IS 204.

- do - 100mm long Aluminium Butt hinges IS 205.

- do - 125mm long Aluminium Butt hinges IS 205.

- do - mild steel ( powder coated ) Butt hinges 100 mm long with ISI mark 205

- do - mild steel ( powder coated ) Butt hinges 125 mm long with ISI mark 205

- do - Anodised Alluminium door handles 100 mm long IS 208.

- do - Anodised Alluminium door handles 150 mm long IS 208.

- do - Door stoppers (MS Powder coated).

- do - Pin headed Glass 4 mm thick.

- do - Galvanized Iron Fly proof wire mesh of not less than 20 gauge.

- do - Brass Aldrop (IS:2681) 300 mm long.

Supply of Brass Fancy Door handles 250mm long

Supply of M.S. Bolts, Nuts and washers

Supply of G.I.Bolts and Nuts

Sun Control film to the glazed windows partition including labour charges

Providing and fixing Aluminium Extruded Section Body Tubular Type Hydraulic Door Closer (IS: 3564) with double speed adjustment with necessary accessories and screws etc. complete (Type-3: for width of doors 851 to 1000 mm)

Supply of Stainless steel fly proof wire mesh of not less than 20 gauge

Supply and fixing of door shutters made of rigid PVC extruded hollow section (Nandi or equivalent) of 20mm X 200 mm with the wall thickness of 1.0mm +/- 0.1mm equally divided into 4 no's with tongue and groove locking arrangements. The shutter frame is made of 30mm X 79mm with the wall thickness of 1.5mm +/-0.15mm section meter-cut and joined at 4 corners with 125mm X 225mm plastic brackets. The shutter shall be horizontally reinforced with 2 no's of 8mm PVC rods. Teak wood batons shall be reinforced inside the door shutter during the fabrication of the door shutter at those points wherever the hardware is fixed onto the door shutter.

Supply and fixing of door frame made of hollow extruded PVC section having dimensions of 40 X 46 mm with the wall thickness of 2mm +/- 0.2mm duly reinforced with seasoned wood plank at the hinges side. The door frame top 2 corners shall be mitre cut/welded.

Supply and fixing of CEMENT BONDED PRE-LAMINATED PARTICLE BOARDS aluminum glazed partitions using 10MM CEMENT BONDED PRE-LAMINATED PARTICLE BOARDS and 5.00 mm thick plain glass to full height. Using with LAM to a height of 0.91 meter at bottom panel and remaining height with glass and aluminum sections anodized to 12 to 15 microns and of sections of size 37mm x 62mm and 1.5mm thickness with one meter centre to centre duly fixed with clip beading on both sides including fixing the frame to pillars by M.S. flats, bolts and nuts including cost and conveyance of all materials etc., complete as directed during execution.

Supplying & Fixing Orissa Pan of size 580 mm x 440 mm white glazed W.C 1st quality ISI marked conforming to IS:2556-Part-3-1981 with "P" or "S" trap ISI Mark or equivalent brand approved by the department.

Supplying and Fixing European Water Closet of 1st quality conforming to IS:2556-Part-2-1973 of white glazed with 'P' trap with ISI mark or equivalent brand approved by the department.

Supply and fixing best Indian make plastic seat and lid for European water closets with rubber of plastic buffers as per IS 2458-1996.

Supply of the following labour as and when required by the dept., as directed during execution.

- do - Carpenter / Stone cutter / Manson / Plumber - Semi skilled work man ( Second class )

- do - Welder / Fitter - Semi skilled work man ( Second class )

Man / Woman Mazdoors

Helpers / Cleaners (2nd class)

Hire charges for following including fuel charges crew charges etc., complete as directed during execution.

- do - for Core drilling machine / Drilling Equipment

- do - for Jack Hammer

- do - for Welding set

- do - for Tractor with 2T Roller.

Supply of Welding electrodes 4 mm dia

Engaging of the following machinery as and when required for dept. The rate is inclusive of crew, oils, conveyance of machinery to site and all other incidental charges.

- do - 3 Ton capacity Crane.

- do - Dozer (D50)

Supply and fixing of PVC low level system with internal components and short bend 10 liters capacity single flush.

Supply of the following UPVC / SWR pipe fittings( U.V resistant) as per approved make with ISI standards

- do - 75mm dia 3 Mts single socket pipe.

- do - 110mm dia 3 Mts single socket pipe.

Supply of the following UPVC / SWR pipe fittings( U.V resistant) as per approved make with ISI standards

- do - 110mm dia Plain bend 87.5 degree

- do - 110mm dia Plain bend 87.5 degree

- do - 75mm dia Single Tee.

- do - 110mm dia Single Tee.

- do - 3" (76.2 mm ) Nahany Trap with Jali

Supply of Country nails

Supply of Deluxe window stay Aluminium

Supply & Fixing of following accessories including all incidental charges etc., complete.

- do - 38.1 mm dia PVC solid waste pipe outlet

- do - 12.7 mm PVC connection with brass union nut C.P coated

Supply of Medium Teak wood scantlings up to 2 mts

Supply of country wood scantlings (Vepa / Neredu) up to 2 meters

Labour charges for wrought and put-up for wood scantlings.

Supplying & Fixing Indian make Flat Back Wash Hand Basin of size 550 x 400 mm - Single C.P. Pillar cock, 1st quality confirming to IS:2556-Part-4:1972 with ISI mark or equivalent approved by the department, with waste fittings like rubber plug, chain, 32 mm nominal size C.P. Fitting with parallel pipe thread confirming to IS:2963-1979 and fitted with 15 mm nominal bore Chromium Plated Pillar Tap of 1st quality Indian make 400 grams complete with standard CI brackets including wooden block.

Cut stone flooring, Steps & Kerb stone dressing Mason labour charges. - for One line dressing

Painting, repolishing and including laying (Weather proof) to the existing Brass name boards and to provide 9 mm thick water proof plywood at the rare side and also 25x15 mm BITW Ornamental decorative repairs for all round the brass board including cost of plywood hooks, screws, polishing etc., as directed during execution.

Writing the sign boards, Direction boards and painting Rangolies over M.S sheet with two coats of back ground one coat primary & one coat synthetic enamel paint over the sign boards with printing two coats with synthetic enamel paint over the back ground. The rate includes cost of paint, labour charges, scaffolding etc., required for the work. The paint should be done with first quality synthetic enamel paint of approved colour and make as directed during execution.

Hire charges for Supply and erection of digital design flex banner with required material like threads and sticks etc., to erect specified place as directed by the department. The cost is including material, labour for printing, erection and removal after completion of the function etc complete as directed during execution.

Hire charges for supply, erection and removal of digital design flex boards with frame work made with of 25mm x 25mm MS square pipe (light weight)with required back support to erect boards at specified places as directed by the department. The cost inclusive of materials, labour for printing, erection and removal square pipe (light weight) after completion of the function.

Removing the existing cut stone flooring carefully without damage. The stone should be conveyed and stacked as specified by the department as directed during execution. The rate is including labour charges for removing the slab carefully without damage, loading lifting stacking at site etc., complete as directed during execution.

Labour charges for re- laying the cut stone flooring as directed during execution, the rate is including lifting the cut stone slabs from store yard and unloading the same at work site carefully without damage etc., complete. The slabs should be jointed with CM ( 1:2 ). The joint should not be more than 6mm thick and the mortar should not come over the stone. The slabs should be laid jointed to proper alignment as directed during execution.

Supply of glow sign vinyl stickered name plate / sign (or) instruction boards using 3mm foam white sheet as back ground and glow sign vinyl sticker one layer for letters of different sizes as directed during execution including cost of 3mm foam sheet vinyl sticker and all labour charges for computer design and cutting, pasting and fixing the boards as directed during execution.

Supply of Brass name plate of different sizes of 20 gauge brass sheet in different languages as directed during execution including weather proof of Brass plates on both sides including Art work as required for the lettering / Figuring etc., complete.

Providing and applying tack coat with bitumen emulsion (Rapid setting) at the rate of 0.20 kg per sq.m using emulsion pressure distributor, on the prepared bituminous / granular surface cleaned with mechanical broom and Air compressor 250 cfm etc., as per Technical specification No.503 MORTH directed by Engineer-in-charge during execution.

Providing and laying Bituminous concrete of specified thickness by Hot mix plant 100-120 TPH capacity using bitumen of grade VG30, IRC size HBG crushed stone aggregates of specified grading, premixed with bituminous binder and filler (Qurry Rubbish) conforming to Table 500-17 & Table 500-9, transporting the hot mix to work site, laying with a mechanical paver finisher to the required grade, level and alignment rolling with smooth wheeled 8-10 tonne, vibratory 8-10 tonne and tandem 6-8 tonne rollers to achieve the desired compaction as per Specification vide Clause No.507 of MORTH (5th Revision) etc., complete in all respects and as directed by the Engineer-in-charge during execution.

Note : 1. Although the rollers are required only for 3 hrs as per norms of output, but the same have to be available at site for 6 hrs as the Hot mix plant and paver will take six hours for mixing and paving the output of 450 tonnes considered in this analysis. To cater for the idle period of these roller there usage rates have been multiplied by a factor of 0.65.

2. Quantity of Bitumen has been taken for analysis purpose. The actual quantity will depend upon job mix formula.

3. Labour for traffic control, watch and ward and other miscellaneous duties at site including sundries have been included in administrative overheads of the contractor.

4. The individual density for each size of aggregates to be used for construction I.e.,37.5-25 mm, 25-10 mm etc., should be found in the laboratory and accordingly the quantities should be amended for use in field. The average density of 1.5 tonne/cu.m is only a reference density in this Data Book.

5. The individual percentage of aggregates should be calculated from the total weight of dry aggregates I.e., excluding the weight of bitumen. The weight of filler will also be 2 per cent by weight of dry aggregates.

- do - Grading - II 13.2mm (Nominal Size) Layer thickness - 30 to 40mm with bitumen binder @ 5.4% minimum by weight of total mix

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforcedwith 1.60 ± 0.2 mm thick galvanized mild steel section made from rollforming process of required length (shape & size according to uPVCprofile), appropriate dimension of uPVC extruded glazing beads anduPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (whitepowder coated) touch locks with hook, zinc alloy body with single nylonrollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mmsize for fixing frame to finished wall and necessary stainless steel screwsetc. Profile of frame & sash shall be mitred cut and fusion welded at allcorners, including drilling of holes for fixing hardware's and drainage ofwater etc. After fixing frame the gap between frame and adjacent finishedwall shall be filled with weather proof silicon sealent over backer rod ofrequired size and of approved quality, all complete as per approved drawing& direction of Engineer-in-Charge inclusive of cost of Single / double glass panes, wire mesh and silicon sealent .

-do- Three track three panels sliding window with fly proof SS wire mesh(Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm) Note: For uPVC frame and sash extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable.Variation in profile dimension in higher side shall be accepted. But no extra payment on this account shall be made.