ADDITION ALTERATION OF 60 MD ACCN AT VARIOUS LOCATION AT YOL

Amount

Dismantling plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Supply & fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Supply & fixing Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Dismantling wall and ceiling boards (fiber, pulp, insulation etc) or insulation boards/ slabs/ blankets, any thickness including cover fillets in ceiling complete all as specified and directed.

Supply & fixing Aluminium anodised snap grid frame work of size of size 605 mm X 605 mm as in false ceiling, flat or sloping (pattern as per manufacturer's catalogue/ instructions), cutting holes for electrical fittings fixed on and including aluminium tee of size 25mmX25mmX1.50 mm as main runner, aluminium tee of size 25mmX25mmX1.25 mm as cross runner and aluminium angle of size 25mmX25mmX1.25mm at the perimeter suspended from soffit at approx 900 mm centre to centre with hangers 6 mm dia galvanised (length as per site requirement) adjusting level fixed to roof by means of ceiling cleats made out of galvanised iron flat 40 mm X 3 mm size, 60 mm long and expansion hold fasteners 12.5 mm dia, 40 mm long including necessary scaffolding all as specified and directed.

Supply & fixing non asbestos fibre cement building boards 6 mm thick fixed or laid/ inserted to timber/GI/Aluminium framework with screws including preparing new surfaces of ceiling boards and applying three coats of white wash, complete all as specified and directed by Engineer-in-Charge.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Material & Labour for glazed coloured ceramic tiles of size 350x250x7mm/450x350x7mm thick fixed on verticle surfaces, set and jointed in neat cement slurry and pointed in white and coloured cement to match, incl 10mm thick rendering in CM 1:4 on fair & other faces of brickwork, conc or stone work complete all as specified and directed by Engineer-in-Charge.

Material & Labourfor coloured non skid cermic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm, laid in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

Material & Labourfor coloured non skid cermic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.18 sqm but n.exc 0.38 sqm, laid in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

Roughening surfaces of old concrete floor by picking, sweeping cleaning and washing down with water to remove dust, etc. brushing with neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and directed by Engineer-in-Charge.

Material & Labourfor 18-20 thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and duly machine cut in skirting/dado laid over cement screed and jointed with grey cement slurry including cutting and polishing including 15 mm thick screed bed layer of cement mortar 1:4 including pointing is white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and directed.” Note : The granite slab shall be fixed one piece, No joint shall be provided on slab except the situation where L-shaped slab is required. Contractor shall note this requirement while quoting his bid

Rounding to edges of stone/kota/marble/granite slabs one edge, such as in steps, cooking platform, and other similar situations

Machine cut kota stone slab flooring 18-20mm thick over screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete and incl 15mm thick screed bed in CM 1:4 complete all as specified and directed.

Material & Labour for kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed including 10mm cement screed plaster in CM 1:4 complete all as specified and directed. (Note:- The kota stone on treads & risers shall be fixed in one piece only. No joints shall be provided. Contractor shall keep this aspect in his mind while quoting his rates).

Demolition of brick/stone work built in cement mortar including all quoins, arches, pillar including coping etc., complete all as specified and directed.

Material & Labour for walling of random rubble , uncoursed well bonded, bedded and solidly hearted built in CM 1:6 complete all as specified and directed.

Material & Labourfor brick work with fly ash old size bricks, straight or curved on plan exc 6m redius, in cement mortar 1:6 complete all as specified & as directed by Enginer-in-Charge.

Material & Labourfor brickwork with flyash old size bricks, straight or curved on plan to any radius in half brick thick walls, in cement mortar 1:6 complete all as specified & as directed by Enginer-in-Charge.

Supply & fixing for Rolled mild steel work in main and cross beams, hip and jack rafters, purlin where connected to common rafter and similar work all as specified and directed.

Supply & fixing Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 10 n exc 15cm long and diameter of shank 5 to 10mm complete all as specified and directed.

Supply & Fixing rolled mild steel work as in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe-410- W(Gde-E-250) quality-B complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided complete all as specified and directed.

Material & Labourfor nominal mix RCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate as in slab supported on walls,beams and columns in floors,roofs,landings,balconies,canopies,deck slabs and in shelves lintel/roof band and the like complete complete all as specified and directed by Engineer-in-Charge.

Material & Labourfor MS TMT bars 10mm dia and over cut to length,bent to shape required incl. cutting,cranking,hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia complete all as specified and directed.

All as per item No 28 here-in-before but 6mm to 8mm dia complete all as specified and directed. By Engineer-in-Charge.

Material & Labourfor formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick horizontal or sloping for rough finished surfaces of finished concrete flat complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide for rough finished surfaces of finished concrete complete all as specified and directed.

Material & Labourfor cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, unshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring,etc., and making good, cutting not exc 10 cm girth in brick walls, complete all as specified and directed.

Taking up or down 15mm dia steel tubing and connections from wall / ceiling or laid floors complete all as specified and directed Engineer-in-Charge.

Taking up or down 20mm dia steel tubing and connections from wall / ceiling or laid floors complete all as specified and directed by Engineer-in-Charge.

Taking up or down 25mm dia steel tubing and connections from wall / ceiling or laid floors including cleaning for refixing complete all as specified and directed by Engineer-in-Charge.

Supply & fixing 15mm bore medium grade glavanised tubes with all fittings and fixed complete to walls etc complete all as specified and directed by Engineer-in-Charge.

Refixing old GI tubing 15mm bore medium grade glavanised tubes and connections in new or old position (walls, ceiling floor etc) complete all as specified and directed by Engineer-in-Charge.

Supply & fixing 20mm bore medium grade glavanised tubes with all fittings and fixed complete to walls etc. complete all as specified and directed by Engineer-in-Charge

Refixing old GI tubing 20mm bore medium grade glavanised tubes and connections in new or old position (walls, ceiling floor etc) complete all as specified and directed by Engineer-in-Charge

Supply & fixing 25mm bore medium grade glavanised tubes with all fittings and fixed complete to walls etc complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in repairs stainless steel sinks with drainage board made of 1mm thick for kitchen with plugs, washer, waste pipes, cast iron cantilever brackets, connecting union to pipe of overall size 915mm x 460mm, bowl size 410 x330 x 160mm with glossy finish,waste coupling 32 mm bore of discharge pipe including bedding in cement mortar to dwarf wall fixing cantilever brackets and connecting unions to pipe complete all as specified and directed by Engineer-in-Charge

Supply & fixing in repair chromium plated shower rose 125mm size complete all as specified and directed by Engineer-in-Charge

Supply & fixing 100mm size steel locking bolts with mild steel electrogalvanised plate and bright bolt not less than 10mm dia complete all as specified and directed.

Supply & fixing in repair Vitreous China wash down water closet pan with 'P' trap (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) Pedestal pan and trap, including connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe, etc.complete all as specified and directed by Engineer-in-Charge

Supply & fixing health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25m long flexible tube and wall hook including making connection and fixed in position complete in all respect all as specified.

Supply & Fixing in repairs for 10 ltr capacity PVC valveless syphonic action type duel flushing cistern, low level white with inlet ball valve float and handle incl brackets complete all as specified and directed by Engineer-in-Charge

Supply & Fixing in repairs for vitreous china wash hand basin white flat back, size 450x300mm incl brackets, cutting for and pinning in ends or brackets withwaste coupling of PTMT bore of 32 mm dia discharge pipe (half or full threaded) minimum wt 32 mm (45 gms/40-60 gms) complete all as specified and directed by Engineer-in-Charge

Supply & fixing in repair Pillar taps cast copper alloy with capstan heads, chromium plated screwed down high pressure with or without lettered Hot or cold with long screwed shanks and flynuts, scewed for union pipe and fixed to 15mm dia pipe complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in repairs tubular towel rail brass chromium plated, 20mm dia, D type 60 cm long fixed between flanges by Engineer-in-Charge.

Supply & fixing CP soap dish 150mm size complete all as specified and directed by Engineer-in-Charge

Supply & fixing Sheet glass shelf assembly consisting of 5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in repair 15mm bore dia of stop valves but fancy type, chromium plated with long shank and cup (cancealed type) screwed down high presure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in repair 15mm bore dia of angle valves cast copper alloy screwed down high presure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in repair bib taps 15mm bore, fancy type cromium plated with butterfly handle, screwed down, high pressure, with carutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in repairs harrison rails, stainless steel, with fixing brackets, stops, rollers etc., complete all as specified and directed.

Material & Labour for PVC (SWR) 110mm bore (dia) soil, waste and ventilating pipe, single socketed, in any length with rubber ring Joints fixed to walls, including taking down unserviceable pipe, fittings, etc, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for PVC (SWR) 110mm bore (dia) PVC (SWR) pipes single socketed, in any lengthwith rubber ring joints, laid in trenches or in floors including taking down unserviceable pipe, fittings, etc, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for PVC (SWR) 75mm bore (dia) soil, waste and ventilating pipe, singe socketed, in any length with rubber ring Joints fixed to walls, including taking down unserviceable pipe, fittings, etc, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for PVC (SWR) 110mm bore (dia), bends any type, with access Door, etc. and jointing with solvent cement, complete all as specified and directed.

Material & Labour for PVC (SWR) 75mm bore (dia), bends any type, and jointing with solvent cement, complete all as specified and directed.

Material & Labour for PVC (SWR) 110mm bore (dia), single T Junction equal or unequal with Access Door, etc. and Jointing with Solvent Cement, complete all as specified and directed.

Material & Labour for PVC (SWR) 75mm bore (dia), Single T Junction equal or unequal with access door, etc. and jointing with solvent cement, complete all as specified and as directed.

Supply & fixing110mm dia PVC (SWR) vent cowl complete all as specified and directed.

Supply & fixing110mm dia PVC (SWR) 'P’ trap complete all as specified and directed.

Supply & fixing PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

Supply & fixing in repairs CP grating 125mm complete all as specified and directed..

Supply & fixing rotational moulded polyethylene water storage tank ( cylindrical vertical with closed top) hoisted and fixed in position of 500 liters capacity confirming to IS specification,incl dismantling of water tank complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in repair 20 mm dia ball valves, high pressure of epoxy coated aluminium rod and high density plastic ball complete screwed for iron pipes or brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in repairs 20mm bore gun metal globe or gate valve cast copper alloy, screwed down, high pressure with cruth or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed by Engineer-in-Charge.

Taking down chowkats or frames with shutters n.exc 1.50sqm each (without taking off shutters from the frames) complete all as specified and directed by Engineer-in-Charge.

All as per item No 68 here-in-before but exc 1.50 Sqm but n,exc 4 Sqm each complete all as specified and directed by Engineer-in-Charge.

Supply & fixing pressed steel frames for doors of size 105mmx60mm, 1.25mm thick MS sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed complete all as specified and directed by Engineer-in-Charge.

Supply & fixing pressed steel frames for doors of size 125mmx60mm, 1.25mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, & as directed by Engineer-in-Charge.

Supply & fixing 35 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides all as specified and as directed by Engr-in-Charge.

Supply & fixing 35mm thick , 2nd class hard wood, Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing solid PVC door frame of size 50 x 47mm made out of 5mm plain coloured PVC sheet reinforced with MS square tube, in opening all as specified and directed by Engineer-in-Charge.

Supply & fixing factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed.

Supply & Fixing for factory made solid PVC door frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet and edges shall be painted to match with prelam sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 180 of MES SSR 2020 Part-II complete all as specified and directed.

Supply & Fixing for factory made fully glazed PVC window/ventilator shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; complete all as specified and directed.. Note:- Glass shall be measured and paid separately.

Supply & fixing Steel window 1.25mm thick box type (Primer Coated) ERW hollow P section of size 60mm x 25mm double rebated comprises gauged/glazed skelton shutter ERW sec 50mm x 20mm and 1mm thic with one or two openable leaf as directed consiting two Nos sash bar of T-Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 30mm x 25mm and 1.25mm thick including coutting holes and making good dismantled portion in PCC (1:2:4) type B-1 using 20mm graded crushed stone aggregate, four Nos for each window including following fitting welded to frame shutter. (i) Hold fast, 150mm long of 12mm x 3mm made to shape-04 Nos per window. (ii) Handle of Z sec 20mm x 25mm, 100mm long-1 No Per. Leaf. (iii) MS tower bolt 150mm long-2 No per leaf (iv) Z Sec 20mm x 25mm, 100mm long stopper-1 No per leaf. (v) Cleat 65mm long of hollow square 15mm x 20mm x 63mm weldeg to hinge-1 No per leaf. (vi) MS Pintal hinges of size 75mm x 12mm - 2 Nos per leaf. (vii) Fabrication & fixing arrangement as per drg No. CEPZ TD-26/13

Supply & fixing MS work with angle or any other section as in window gurad bars, grill and other similar works all specified and directed.

Supply & fixing for stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.4mm and fixed with stainless steel wire staples all as specified & as directed by Engineer-in-Charge.

Supply & fixing for 3mm thick sheet glass, ordinary quality and glazing with oil putty in square n,exc 0.50 Sqm in each pane.

Supply & fixing 3mm thick figured glass, pin head type and glazing with oil putty in squares in exc 0.5 sq.m in each pane.

Supply & fixing 2nd class hard wood small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary labours; articles n exc 200 cu. cm each complete all as specified and directed.

Supply & fixing for MS butt hinges 100mm size, medium weight complete all as specified and directed.

Supply & fixing for MS butt hinges 75mm size, medium weight complete all as specified and directed.

Supply & fixing for 200mm length aluminum, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

Supply & fixing for 150mm long aluminum, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

Supply & fixing 150mm long aluminium handles, cast type anodised complete all as specified and directed.

Supply & fixing 125mm long aluminium handles, cast type anodised complete all as specified and directed.

Supply & fixing aluminium alloy, anoised sliding door bolt 250mm, with hasp staple and fixing clips of sheets cast or extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

Supply & fixing door spring, heavy type, 300 mm long including roller and roller plate, , all as specified and directed.

Dismantling boarding, any description fixed in any position with nails complete all as specified and directed.

Supply & fixing 15mm thick 2nd class hardwood boarding planed one side with butt joints & and fixed with nails in any situation complete all as specified and directed.

Material & Labourfor 18mm thick Pre-laminated particle board,exterior grade,prelaminated one side with decorative choice lamination and other side balancing white lamination,fixed with screws to timber frame work complete all as specified and directed.

Material & Labourfor plain fillets. square, rectangular or triangular in section, clean sawn, secured with nails or brads exc 13 & n exc 25 sq. cm.2nd class hardwood.

Supply & fixing continuous (piano) hinges mild steel, bright fin ish or electrogalvanised width of flaps 40mm ( when open) complete all as specified and directed.

Supply & fixing Steel plate rack of over all size 900mmx900mmx250mm made of stainless steel having thickness 1mm, fixed over fixing 40cm long MS angle of size 25mmx25mmx3mm- 02 Nos each on walls, complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and pavings n. exc 15cm thickness (below or above ground level) all as specified and directed.

Material & Labourfor PCC 1:4:8 type D2 (using 40mm graded crushed stone aggregate) as in sunken floor all as specified and directed.

Material & Labourfor APP based Polymeric membrane minimum weighing 3 kg/Sqm and minimum 3 mm thick reinforced with polyster non woven fabric ( wt not less than 150 gms/sqm) laid on primed surface forced application for sunken floor of WC and baths complete all as specified and directed.

Material & Labourfor bitumen blown any grade, applied hot, two coats, to concrete surfaces at the rate of 1.5kg per sq. m. per coat complete all as specified and directed by Engineer-in-Charge.

Material & Labourfor 32mm dia GI Pipe medium grade as in spout of sunken floor 450mm long complete all as specified and directed by Engineer-in-Charge..

Material & Labourfor PCC M-10 ( Nominal mix) 50mm thick, using 20mm graded crushed stone aggregate as in paving, plinth protection etc, surfaces finished even and smoothwithout using extra cement and dividing into panells not exc 1.20 Mtr all as specified and directed.

Material & Labourfor 25mm thick PCC(1:2:4) type B-0 using 12.5mm graded crushed stone aggregate as in floor finished even and rough to received the topping layer complete all as specified and directed.

Taking down cement plaster/decayed concrete from RCC roof projections/upward parapet walls/ down ward facia/soffits and fins of RCC chajjas /beams/columns/balconies etc. Supply and fixing by means of nailing wire netting of galvanised wire 1.40 mm dia and mesh size 20 mm and brushing neat cement slurry with 3.00 kg of cement/sqm and Material & Labour for 20 mm thick cement rendering in two layers of 10 mm each (top/final layer shall be rendered after final setting of under layer) in Cm 1:3 on concrete surfaces including scaffolding at a height upto 7.00 mtrs. etc complete all as specified and directed.

Water proofing treatment over terrace high solid content single component water based liquid applied elastomeric water proofing membrane as ASTMC 836 and ASTMD 6083, thickness of the membrane shall be 1.5mm, having solid content of more than 80% elongation of 500+(-) 50%, laid over reinforcing layer on non woven geo-textile mesh of 40/50, 50 gms, including applying self primer coat by diluting with 1:1 ratio @ 0.2 kg per sqm and surface preparation including cleaning of existing treatment complete all as specified and directed.

Taking down cement plaster on brick walls etc, incl racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed..

M& L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick / concrete/stone, surfaces and finished even and smooth without using extra cement mixed with WPC @ 3% by Wt. of cement (External surfaces) complete all as specified and directed by Engineer-in-Charge. (Note:- WPC shall be measured & paid for separately.)

Supply only integral water proofing compound complete all as specified and directed..

Rendering 15mm thick on fair faces of brick/stone or concrete surfaces in CM 1:6 and surface finished even and smooth without using extra cement (Internal surfaces) complete all as specified and directed.

Rendering 15mm thick on other than fair faces of brick/stone or concrete surfaces in CM 1:6 and finished surface even and smooth without using extra cement (Internal surfaces) complete all as specified and directed.

Material & Labourfor rendering 5mm thick in cement mortar 1:3 on fair faces of RCC surfaces including applying cement slurry in bottom of slab or ceiling, chajjas, finSupply & Fixingacias etc complete all as specified and directed..

Material & Labourfor preparation of newly plastered surface of walls and applying two coats of oil bound distemper over 2mm wall putty to achieve smooth surface complete all as specified and directed.

Material & Labourfor preparation of new plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

Material & Labourfor preparation of newly plastered surface of walls and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. complete all as specified and directed by Engineer-in-Charge.

Complete removal of existing treatment of wall sufaces and applying two coats of oil bound distemper over 2mm thick wall putty to achieve smooth surface complete all as specified and directed by Engineer-in-Charge.

Material & Labourfor preparation of old plastered or un plastered , previously undecorated wall surface by complete removal of existing treatment and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon adhesive @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed.

Material & Labourfor applying two coats of synthetic enamel paint over one coat of pink primer on newly prepared wooden surfaces of any description, not otherwise described over 10cm width or girth complete all as specified and directed.

Material & Labourfor two coats of synthetic enamel paint over one coat of red oxide exc 10cm width or girth on newly prepared steel surfaces complete all as specified and directed.

Material & Labour for preparation of old steel surfaces over 10cm width or girth and painting with synthetic enamel painting one coat complete all as specified and directed.

Material & Labour Chequered cement concrete tiles of size 25cmx 25cmx 20 mm thick (with grey cement and no pigments) set, jointed and pointed in neat cement slurry in floor,laid over and incl 15mm thick cement screed base in CM 1:4, complete all as specified and as directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified.

Material & Labour for 100mm thick Plain cement concrete M-7.5 nominal mix, type D-2, using 40mm graded crushed stone aggregate as sub base to floor, surfaces finished even and fair complete all as specified and directed.

Material & Labourfor broken stone/boulders hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface.

Material & Labour for 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

Material & Labour for Providing, cement concrete (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregate) in roof kerbs or mud stops, rounded orchamfered on edges in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed.

Demolition and breaking up 150mm dia, drain pipes (PVC, Salt glazed stone ware, AC or Reinforced concrete) set in cement mortar any size and in any position including all fitting complete all as specified and directed.

Material & Labour for providing PCC M 7.5 (Nominal mix) type D-2, using 40mm graded crushed stone agg as in bed of drain pipe 150mm dia (nominal ) including packing under and hanuching against the sides of pipe after they are laid and tested complete all as specified.

Material & Labour for 150 mm dia reinforced concrete pipes,class NP2 laid and jointed with cement complete with collars complete all as specified and directed.

Material & Labour for 150mm dia salt glazed stone ware drain pipe and jointed complete all as specfied.

Cutting into existing manholes for connecting new drains, 150mm dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round 3/4 channel) in cement concrete M-15 type B-1 using 20mm graded crushed stone aggregate finished smooth and reforming benching as required compete all as specified and as directed by Engr-in-Charge.

Supply & Fixing in repairs SGSW gully trap, square or round mouthed, type 'P' of size150x150 mm with CI grating, setting and jointing with cement mortar 1:1 with grouting surrounding with PCC 1:3:6, type C1 using 20 mm graded crushed stone aggregate block of size 300x300 mm including necessary form work and earth work in any type of soil complete all as directed.

Material & Labour for pre cast reinforced cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) in pre cast deck slabs, shelves, cover to man holes, etc and similar works bedded and jointed in cement mortar 1:4 including form work complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and n exc 1.5m in depth for foundations, etc or for shafts , wells, cesspits, manholes, pier holes etc not exceeding 10 Sqm on plan not exceeding 1.5 mtr in depth and getting out in any type of soil, complete.

Returning filling in including spreading leveling watering and well ramming in layers n.exc 25 cm thick complete

Removal of excavated material (soil) n.exc 50m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified

Material & Labour for PCC 1:3:6, nominal mix type C-2 using 40mm graded crushed stone agg as in foundation filling and mass concrete complete.

Material & Labourfor PCC M-10 (Nominal mix) type C-1 using 20mm graded aggregate as in surface channel and drain all as specified.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/ stopped ends etc complete all as specified and directed.

Extra for forming fair finished drain or channel 45 cm inner girth in cement concrete, using extra cement including forms, moulds,mitred/ stopped ends etc complete all as specified and directed.

Cleaning the drains by removing foreign materials / silt/ greasy materials / earth from from the drains, removing the excavated material from site and depositing where directed at a level not exc. 1.5m above the starting point, complete all as specified.

INTERNAL ELECTRIC SUPPLY :Taking down carefully the existing aluminium/copper point wiring of any size and capacity and type by disconnecting from the either terminals complete including fittings and fixtures such as switches, ceiling rose, fan, regulators, lamp holders, call bell, bell pushes any type etc by unscrewing and taken away from the site complete and make good the disturbed surface as existing.

Taking down sheet metal enclosures DBs, main switch board etc and making good disturbed surface to match with existing surface complete all as specified.

Material & Labour for point wiring with 1.5 sqmm (Nominal Area) FRL-SH PVC insulated unsheated multi stranded copper conductor, 1100 Volts grade, in and including PVC casing capping with accessories such as bends, cross, elbow, tees etc. of suitable size including concealed PVC/MS pressed stee; cadmium plated terminal box not less than 1.6 mm thick for mounting switches, sockets, fan regulators etc and 3mm thick laminated sheet top cover (ISI marked) including continuous earth wire FRLS PVC insulated unsheated 1.5 sqmm (nominal area) copper multistranded conductor, 1100 Volts grade, connecting to common earth and earth dolly complete all as specified for one light point/Exhaust fan point controlled by one switch. Note:- i) Wiring Colour i.e Red/Yellow/Blue for Phase, Black for neutral and Green for earth shall be maintained.

All as per item No 145 above but for one three pin socket 5Amp outlet on same board complete all as specified and as directed.

All as per item No 145 above but one three pin socket outlet 5 amps on independent board complete all as specified and as directed.

All as per item No 145 above but for one light point controlled by two way switch all as specified and directed.

All as per item No 145 above but for 3 pin 15 amps socket outlet on independent board with 2.5 sqmm PVC copper conductor cable and PVC insulated, unsheated 2.5 sqmm stranded copper conductor cable as continuous earth wire, all as specified.

Supply & fixing Switch piano flush type single pole one way 5A SP 230 Volts.

Switch piano flush type, single pole, two way, 5 Amps all as specified and directed

Supply & fixing Switch Socket combination outlet 2 in 1 3 pin 5 Amps Flush type.

Supply & fixing Switch Socket combination outlet 2 in 1, 3/5 pin 5 and 15 Amps Flush type.

Supply & Fixing Stepped type electronic fan regulator flush type on the existing phenolic laminated sheet complete all as specified and as directed.

Supply & fixing Ceiling rose surface type 3 terminals 65x20mm complete all as specified

Supply & fixing bell push piano flush type 5Amp single pole one way

Supply & Fixing bell electric, Ding Dong AC 230 Volts, single pole complete all as specified and as directed.

Supply & Fixing sheet metal enclosure single pole and neutral 8 way double door including suitable size copper bus bar and neutral link fixed flush in wall including cutting/chases wall for fixing DB & making good distrubed surface as per existing specifications, completed all as specified and as directed by Engr-in-Charge.

Supply & Fixing sheet metal enclosure powder coated, MCB DB TPN, 4 way, 415 V double door including suitable size copper bus bar and neutral link fixed flush in wall including cutting/chases wall for fixing DB & making good disturbed surface as per existing specifications all as specified and as directed by Engr-in-Charge.

Supply & fixing MCB single pole 240 volts of rating 6 to 32 amps 10 KA including thimbles for outgoing cable complete all as specified & as directed by Engr-in-Charge.

Supply & fixing MCB SPN 240 Volts of rating 6 to 32 amps, 10KA including providing thimbles for outgoing cable complete all as specified & as directed by Engr-in-Charge.

Supply & Fixing MCB, TPN, 63A capacity, 415 V including taking down old MCB TPN (Note:- (i) The MCB DB and MCBs shall be from same company/make (ii) The connection to the MCBs shall be through thimbles/lugs direct wire shall not be connected to MCBs).

Material & Labour for sub main wiring with two single core PVC insulated unsheated, 1100 Volts grade (FRLS) copper cable 6 sqmm stranded conductor and drawing through and including rigid PVC non metallic surface conduit medium duty (ISI Marked) with conduit accessories such as junction boxes, bends, tees etc. including continuous earth wire PVC insulated unsheated 1100 volts grade, cable 6 sqmm copper conductor and connected to common earth dolly complete as directed including taking down old submain wiring. Note :- (i) One run of PVC conduit, two runs of cable (Phase + Neutral) and one run of earth wire shall be measured and paid as one unit.

Material & Labour for wall mounted LED tube light fitting integral type 1x10W, 230 V, connector block etc complete with all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size including dismantling of unserviceable tube light all as specified and directed.

Material & Labour for wall mounted LED tube light fitting integral type 1 x 20W, 230 V, connector block etc complete with all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size including dismantling of unserviceable tube light all as specified and directed.

Taking Down ceiling fan/exhaust fan complete of 1200/250/300 mm sweep from fan hook/wall dismentling blade opening of motor cleaning stator rotor, cleaning of all parts, greasing, oiling of bush & bearing, reassembling & applying painting one coat of synthetic enamel paint of approved quality and colour (Spray painted) after preparing the surface throughly and refixing at site at same/different location all as specified and as directed & marked MES No also & refixing connecting with 2 core copper cable, complete all as specified directed Engineer-in-Charge

Supply & Fixing ceiling fans, complete with three blade, down rod, accessories 230V, 1200mm sweep with minimum air delivery 210 CFM with service value 6.0 BEE, five star rating with BLDC all as specified and directed by Engr-in-Charge.

Taking down water storage heater from electrical socket and plumbing connections kept aside in dafe for reuse at same/different location duly preparation to old painted surface of storage water heater and painting of geyser 25ltr capacity with two coats of synthetic enamel paint (white colour) by using gun and replacement of gyser element and refixing duly gounting nut, bolts, washers and plumbing connection making leak proof complete all as specified and as directed.

Supply & Fixing electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre., BEE 5 Star rated compl;ete with all accessories such as safety valve, thermostate, NRV, connection piece etc.

Supply & Fixing endura pearl 25Watt New generation energy saving and environment friendly long life LED Bldg security light made up of pressure die cast aluminium housing with hogh power LED as lighting source and lens embedded PC cover having TOP opening separate toughtned glass/verminproof driver compartment, SPDs with IP66 protection and impact resistance of IKO7. connecting with PVC insulated three core flexible copper conductor of suitable size from ceiling rose to fitting including bracket of suitable size.

Supply & Fixing in repairs concealed sheet metal enclosures with socket plug top and MCBs having single pole and neutral enclosures with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 Amp 240V complete all as specified and as directed.

Supply & Fixing in replacement exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and as directed.

Taking down AC Meters, checking and repairing at site by repair/replacing of contents, terminals and indicators, glass covers, plate creews, electronic circuit etc and re-fixing in same poistion complete all as specified.

EXTERNAL ELECTRIC SUPPLY:Supply & Fixing in replacement XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 25 Sqmm, 3.5 core laid in trenches passing through pipe/ducts/surface of wall ceiling etc including testing complete all as specified.

Sand cushioning to under ground cables, 8cm thick layer before laying and testing the cable and 15 cm thick after laying and directed by Engr-in-Charge.

Material & Labour for laying of bricks in trenches as cable protection with width equal to the length of bricks complete all as specified and as directed.

Material & Labour for GI light grade pipe of 50mm dia with all fittings laid in trenches, acroos road or pole complete all as specified.

Eathing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth p[it not less than 2.25 metre deep below normal ground level) with top edge of plate not less than 1.5 metre below ground level, connecting to galvanised iron wire 4.00 mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washers of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15mm bore including provn of concrete pit in plain cement concrete M-20 type B-1 using 20mm graded crushed stone aggregates with 40mm thick cover of rainforced cement concrete M-20 reinforced with XPM (weight not less than 4kg/Sqm) and frame of angle iron 25x25x3mm with lugs 2Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangements , funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electrical plate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion. Note: Item of earthing includes the cost of 7.5 metre long galvanised iron earth wire 4mm dia and protection pipe of 15 mm bore galvanised iron light grade and earth work.

Dismantling timber scantlings 40 sqcm and over in section, in any position framed or unframed work etc, complete all as specified and as direceted by Engr-in-Charge.

All as per item No 180 here-in-before but in fillets, rails, posts, rafters, purlins etc under 40 Sqcm in section framed or unframed work etc, complete all as specified and as direceted by Engr-in-Charge.

Supply and fixing rolled mild steel work roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket frame (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc with Fe 410 W (Gde E-250) quality 'A', complete all as specified and as directed.

Note: The Schedule of credit has been attached in tender in Pdf formate and amount of credit schedule i.e Rs 12,43,100.00 shall be deducted from the total amount of BOQ to arrive at the contract sum.

TRIVENI CONSTRUCTIONS

m/S Varun Gupta

surinder kumar jindal & bros.

M/s R S Construction