Supply and Installation 10Mtr, 8 Mtr High Mast and 6 Mtr Mini Mast lights and 5 years warranty at various locations in Thodupuzha LAC.

Amount

Supply and Installation of 8 Nos. of 6 mtr Mini mast system with 3 nos. 70W LED Flood lights and 5 years warranty at various locations in Thodupuzha LAC.

Supply and erection of octoganal galvanized. pole 6 mtr height complete with 4 Nos foundation bolt suitable size base plate , space for mounting control switch box with inspection type door at a height of 500mm from the base plate including Bakelite sheet with 6A SP MCB (4Nos) with suitable Stud terminals etc as required

Earth work excavation in hard soil and depositing with a lead up to 50 m and lift up to 1.50 m including neat banking for foundation earth work(2.6.1)

RCCM20 using 20mm (nominal size) broken stone forFoundation and Column footing (5.1.2) as per drawing

Reinforcement for R.C.C works, bend tied and placed in position (plain grill requiring bend cold) using tor steel 5.22.6

Form work for reinforced cement concrete in slabs including wooden planks, joists, bamboo posts and labour for taking down after completion of work (Hire and labour charges only)

Supply, conveyance, installation, testing and commissioning of LED 70W flood light fitting with all acessories . Luminaire housing component to be aluminium alloy with black powder paint IP 67. Internal surge protection against lightening or any other electrical surge up to 8 KV. .input voltage range 100-240+- l0%,power factor > 90% at full load, ROHS compliance

Supply and drawing the following sizes of multi-core PVC insulated & PVC sheathed 650/1100 V grade 3 core copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface / recess conduit as required including giving necessarv connections of the following sizes.

Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using 1.60 mm CRCA sheet as per approved design and requirement, with front and rear access facility, bus bar chambers, hinged doors for all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary cut-outs for mounting meters, relays, indication lamps, bus bar interconnection etc, detachable covers for bus bar chamber and cable alley, painting the assembly with 2 coats synthetic enamel paint over a coat of zinc chromate primer etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurements should be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc. including control wiring

Fabrication, supply, conveyance and installation of angle iron frame work for wall mounting panel board using suitable size angle iron cut and welded to shape including painting with two coats of synthetic enamel paint over a coat of zinc chromate primer, bolting the frame to the panel using required bolt and nuts, fixing the whole to the wall, making good the damages etc. as required.

Supply and fixing the following types of beeding along the periphery of doors/ other detachable compartments to make the panel assembly dust & vermin proof including sticking with glue

U' section rubber beeding suitable for 1.60/ 2.00 mm sheet

Supply and fixing the following accessories in the existing meter board and giving connections etc.

32 A fuse holder for BS type blade fuses.

32 A,415 V,2 way neutral link mounted on DMC/ SMC base.

20-25 A, clip-on offset tag fuse link of size fl

Supply and installation of the following accessories suitable for 50 Hz , AC supply conforming to IS 8828-1995/ IEC 60898 of the following current ratings in the existing enclosure and giving connections as required

25 A,2 pole, 30 mA RCCB

6 A to 25 A, l0 kA, DP MCB (C curve)

32A,2Pole, AC 1 rated power contractor with lNO+lNC auxiliary contracts & with AC coil

24 Hours Timer for operating automatic ON-OFF function

Supply and fixing the following sizes of PVC Conduit conforming to IS 9537 / 1983 part III along with all required accessories on surface including making good the damages etc as required

25 mm dia light gauge

Supply and providing plate earthing as per IS 3043 with 600x600x6.30 mm GI/CI earth plate,20 mm GI watering pipe fixed to the earth plate with 20 x 3 mm GI clamps, GI funnel with weld mesh, filling required quantity of charcoal including construction of inspection chamber with a bed concrete of l:4:8 PCC using 40 mm broken stone (10 cm thick), brick work in cement mortar 1:6, plastering the surface of brick masonry and the exposed surface of PCC bed with cement mortar l:4, 12 mm thick, (the finished inside dimension shall be 300 x 300 x 300 mm) but excluding test joint, earth continuity conductor to the plate, and covering at the top. (in ordinary soil)

Supply and providing the following sizes of cast iron gully trap with covering at the top of the inspection chamber of earth pit as required

300 x 300 x 6 mm cast iron gully trap with covering

Supply and providing test joint for the earthing system using 2 nos of the following sizes of strips including cutting and bending to shape,drilling necessary ,holes and fixed to the watering pipe etc as required.

2x25 x 3 mm GI strip

Supply and providing earth lead from the test joint to the earth electrode using the following sizes of conductors/ strips including cutting, drilling necessary holes (in case of strip) and fixing firmly with plate test joint etc as required.

25 x 3 mm GI strip

Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required.

3. 15 mm copper condudor ( 10 SWG)

supply' of superior quality copper earth socket for the following sizes of earth conductor including crimping etc. as required.

3.15 mm (10 SWG)

Supply and providing the following sizes of bolt and nut with washers on the existing MS box / earth bus etc. as required including drilling necessary holes as required.

25 x 3mm brass bolt & nut

Supply and wiring with 650,/1100 V grade PVC insulated stranded single core copper conductor cables conforming to IS 694 part I 1990 for interconnecting the control devices/ equipments including providing suitable size sockets at the termination points, keeping the wiring firm by suitable tie/ tie mounts/ PVC duct etc as required.

4.00 sq mm single run without sockets. (for terminating KSEB meter Board)

Charges for KSEB connection including all laison works (Actual Amount paid on production of receipt).

Fabrication ,supply and conveyance and installation of name board indicating the cost involved, the commencement, completion and inauguration date etc.

Supply and Installation of 21 Nos. of 8 Mtr High Mast System with 6 Nos. 70W LED Flood lights and 5 years warranty at various locations in Thodupuzha LAC.

Supply and installation of High Mast system as per following Specification (a) Supply 8 Mtr High Mast system with its accessories . mast shaft shall be in single or two section, Galvanisation of single hot dipped, suitable for wind velocity as per IS 875 Head frame assembly 2 point suspention system with steel wire rope 5/6 mm dia (7119 construction) and double drum winching system arrangement conforming to IS with galvanised lantern carriage suitable for accommodating 4Nos flood light luminaires symmetrically and its control gear box and lightining spike. (b) Supply and conveyance 4/6 Nos foundation bolt made of special steel along with nuts, washers, anchor plates and templates (c) Supply, erection, testing and commissioning of LED aviation obstruction light (d) Supply and erection control box consists of 1 No. 25A, 2 pole MCB incomer, single dial 24 hour timer with charging facility and suitable contractor for automatic operation, suitable size connection cable from control panel to flood light fittings (e) Construction of suitable shallow foundation with l:2:4 Concrete for the high mast considering the safe soil bearing capacity at site as 10 T/Sqmtr at 550mm length x 550mm breadth x 2000mm depth with reiforcement for RCC works, bend tied and placed in position (plain grill requiring bend cold ) using for steel including form ,work for reinforcedcement concrete and excavation of soil including neat banking. (f) Erecrion and commissioning of the above high mast with the help ofcrane/derrick and other suitable equipment and wiring of luminaries with wiring materials (Bajaj/ Crompton/ philips/equivalent make) (MR)

Supply, installation, testing and commissioning of 70W LED flood light luminaire with extruded aluminium heat sink pressure die cast aluminium cover on both side for holding of extruded aluminium heat sink and with voltage range ( l40 - 270 AC). The luminaire shall be minimum IP 66 Protected. 105 lm/w. LED Driver efficiency should be greater than 105 %o with colour temperature should be greater than 5700K range. Inbuilt-surge protection 10kv and power factor 0.95 with THD less than l0%. (MR)

Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using 1.60 mm CRCA sheet as per approved design and requirement. wiith frotr and rear access facility. bus bar chambers. hinged doors ror all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary cut_outs for mounting meters, relays, indication lamps, bus bar interconnection at", detachable covers for bus bar chamber and cable aley, painting the assembly with 2 coats synthetic enamel paint over a coat of zinc chromate primer etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurments should be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc. including control wiring

Supply and fixing the following types of beeding along the periphery of doors/ other detachable comparrments to make the panel assembly dust & vermin proof including sticking with glue A' section neoprene beeding suitable for 1.60/ 2.00 mm sheet

Fabrication, supply, conveyance and installation of angle iron frame work for wall mounting panel board using suitable size angle iron cut and welded to shape including painting with two coats of synthetic enamel paint over a coat of zinc chromate primer, bolting the frame to the panel using required bolt and nuts, fixing the whole to the wall, making good the damages etc. as required.

Supply and fixing the following accessories in the existing meter board and giving connections etc.

32 A,415 V Backelite fuse fitting

32 A,415 V,2 way neutral link mounted on DMC/ SMC base.

20-32 A, clip-on offset tag fuse link of size fl

Supply and installation of the following accessories suitable for 50 Hz , AC supply conforming to IS 8828-1995/ IEC 60898 of the following current ratings in the existing enclosure and giving connections as required

25 A,2 pole, 30 mA RCCB

6 Ato25 A, l0 kA, DP MCB (C curve)

32A,2Pole, AC I rated power contractor with lNO+lNC auxiliary contracts & with AC coil

24 Hours Timer for operating automatic ON-OFF function

Aluminium anodised DangerNotice Board of size 150 x 100 mm. with inscriptions (both in English and Malayalam) and conventional Skull and Bone in Red colour.

Supply and wiring with 650/1100 V grade PVC insulated stranded single core copper conductor cables conforming to IS 694 part I 1990 for interconnecting the control devices/ equipments including providing suitable size sockets at the termination points, keeping the wiring firm by suitable tie/ tie mounts/ PVC duct etc as required. 4.00 sq mm single run without sockets

Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of l.1 KV grade of the following sizes in the existing RCC HUME/ STONE WARE /GI/ DW C pipe as required.

2 core 10 sq mm

Supplying siemens/ tropodur type nickel plated Double compression brass cable gland for PVC insulated and PVC sheathed armoured aluminium/ copper conductor cable 1.1 KV grade, and making end termination suitable for2/ 3/3.5/4 core cable of the following sizes as required.

l0 sq mm

Supplying and providing earth clamps for siemens tropodur type cable glands of suitable length and other dimensions noted along with each size of glands for the followinge sizes of cables as required.

4sqmm-16 sq mm with 12 mm wide x 1 mm thick clip

Supply of superior quality aluminium tubular cable socket and making core termination of cables of the following sizes including crimpirg etc. as required.

Supply route marker with 102mmx102mm cast iron, spike 5mm thick with inscription 'LT Cable, there on bolted / welded to 35x35x6mm angle iron 60cm long and fixing the same in ground as required.

Supplying, laying and jointing of the following sizes of double wall corurgated (DWC) pipes made out of HDPE conforming to IS 14930 Part II for mechanical protection to underground power cables with all required accessories in hard soil 0.75m below ground level including excavation

40 / 32 mm or nearest size

Supply and fixing the following sizes of PVC Conduit conforming to IS 9537 / 1983 part III along with all required accessories on existing pole/ concrete etc. as service/protection pipe as required

32 mm dia light gauge

Supply and providing plate earthing as per IS 3043 with 600x600x6.30 mm GI/CI earth plate ,20 mm GI watering pipe fixed to the earth plate with 20 x 3 mm GI clamps, GI funnel with weld mesh, filling required quantity of charcoal including construction of inspection chamber with a bed concrete of 1:4:8 PCC using 40 mm broken stone (10 cm thick), brick work in cement mortar l:6, plastering the surface of brick masonary and the exposed surface of PCC bed with cement mortar l:4, 12 mm thick, (the finished inside dimension shall be 300 x 300 x 300 mm) but excluding test joint, earth continuity conductor to the plate, and covering at the top. (in ordinary soil.

Supply and providing the following sizes of cast iron gully trap with covering at the top of the inspection chamber of earth pit as required 300 x 300 x 6 mm cast iron gully trap with covering

Supply and providing test joint for the earthing system using 2 Nos of the following sizes of strips including cutting and bending to shape, drilling necessary holes and fixed to the watering pipe etc as required.

2x25 x 3 mm GI strip

Supply and providing earth lead from the test joint to the earth electrode using the following sizes of conductors/ strips including cutting, drilling necessary holes (in case of strip) and fixing firmly with plate test ioint etc as required.

25 x 3 mm GI strip

Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required.

3.15 mm copper conductor (10 SWG)

25 x 3 mm GI strip

Supply of superior quality copper earth socket for the following sizes of earth conductor including crimping etc. as required.

3.12 mm (10SWG)

Supply and providing thefollowing sizes of bolt and nut with washers on the existing MS box i earth bus etc. as required including drilling necessary holes as required

25 x 6mm brass bolt & nut

25 x 8 mm GI bolt & nut

Fabrication, supply and conveyance and installation of name board with Granite stone with requird inscriptions such as scheme and the required names etc. supported by using suitable size angle iron frame work including painting and fixing the whole near the high mast pole as required including two nos photograps

Charges for KSEB connection including all laison works (Actual Amount paid on production of receipt).

Supply and Installation of 2 Nos. of 10 Mtr High Mast System with 6 Nos. 100W LED Flood Lights and 5 years warranty at KSRTC Junction and Municipality Frontage at Thodupuzha LAC.

Supply and installation of High Mast system as per following Specification (a) Supply 10Mtr High Mast system with its accessories . mast shaft shall be in single or two section, Galvanisation of single hot dipped, suitable for wind velocity as per IS 875 Head frame assembly 2 point suspention system with steel wire rope 5/6 mm dia (7119 construction) and double drum winching system arrangement conforming to IS with galvanised lantern carriage suitable for accommodating 6Nos flood light luminaires symmetrically and its control gear box and lightining spike. (b) Supply and conveyance 4/6 Nos foundation bolt made of special steel along with nuts, washers, anchor plates and templates (c) Supply, erection, testing and commissioning of LED aviation obstruction light (d) Supply and erection control box consists of 1 No. 25A, 2 pole MCB incomer, single dial 24 hour timer with charging facility and suitable contractor for automatic operation, suitable size connection cable from control panel to flood light fittings. (e) Construction of suitable shallow foundation with l:2:4 Concrete for the high mast considering the safe soil bearing capacity at site as 10 T/Sqmtr at 550mm length x 550mm breadth x 2000mm depth with reiforcement for RCC works, bend tied and placed in position (plain grill requiring bend cold ) using for steel including form ,work for reinforcedcement concrete and excavation of soil including neat banking. (f) Erecrion and commissioning of the above high mast with the help ofcrane/derrick and other suitable equipment and wiring of luminaries with wiring materials (Bajaj/ Crompton/ philips/equivalent make) (MR)

Supply, installation, testing and commissioning of 100W LED flood light luminaire with extruded aluminium heat sink pressure die cast aluminium cover on both side for holding of extruded aluminium heat sink and with voltage range ( l40 - 270 AC). The luminaire shall be minimum IP 66 Protected. 105 lm/w. LED Driver efficiency should be greater than 105 %o with colour temperature should be greater than 5700K range. Inbuilt-surge protection 10kv and power factor 0.95 with THD less than l0%. (MR)

Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using 1.60 mm CRCA sheet as per approved design and requirement. wiith frotr and rear access facility. bus bar chambers. hinged doors ror all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary cut_outs for mounting meters, relays, indication lamps, bus bar interconnection at", detachable covers for bus bar chamber and cable aley, painting the assembly with 2 coats synthetic enamel paint over a coat of zinc chromate primer etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurments should be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc. including control wiring

Supply and fixing the following types of beeding along the periphery of doors/ other detachable comparrments to make the panel assembly dust & vermin proof including sticking with glue A' section neoprene beeding suitable for 1.60/ 2.00 mm sheet

Fabrication, supply, conveyance and installation of angle iron frame work for wall mounting panel board using suitable size angle iron cut and welded to shape including painting with two coats of synthetic enamel paint over a coat of zinc chromate primer, bolting the frame to the panel using required bolt and nuts, fixing the whole to the wall, making good the damages etc. as required.

Supply and fixing the following accessories in the existing meter board and giving connections etc.

32 A,415 V Backelite fuse fitting

32 A,415 V,2 way neutral link mounted on DMC/ SMC base.

20-32 A, clip-on offset tag fuse link of size fl

Supply and installation of the following accessories suitable for 50 Hz , AC supply conforming to IS 8828-1995/ IEC 60898 of the following current ratings in the existing enclosure and giving connections as required

25 A,2 pole, 30 mA RCCB

6 Ato25 A, l0 kA, DP MCB (C curve)

32A,2Pole, AC I rated power contractor with lNO+lNC auxiliary contracts & with AC coil

24 Hours Timer for operating automatic ON-OFF function

Aluminium anodised DangerNotice Board of size 150 x 100 mm. with inscriptions (both in English and Malayalam) and conventional Skull and Bone in Red colour.

Supply and wiring with 650/1100 V grade PVC insulated stranded single core copper conductor cables conforming to IS 694 part I 1990 for interconnecting the control devices/ equipments including providing suitable size sockets at the termination points, keeping the wiring firm by suitable tie/ tie mounts/ PVC duct etc as required. 4.00 sq mm single run without sockets

Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of l.1 KV grade of the following sizes in the existing RCC HUME/ STONE WARE /GI/ DW C pipe as required.

2 core 10 sq mm

Supplying siemens/ tropodur type nickel plated Double compression brass cable gland for PVC insulated and PVC sheathed armoured aluminium/ copper conductor cable 1.1 KV grade, and making end termination suitable for2/ 3/3.5/4 core cable of the following sizes as required.

l0 sq mm

Supplying and providing earth clamps for siemens tropodur type cable glands of suitable length and other dimensions noted along with each size of glands for the followinge sizes of cables as required. 4sqmm-16 sq mm with 12 mm wide x 1 mm thick clip

Supply of superior quality aluminium tubular cable socket and making core termination of cables of the following sizes including crimpirg etc. as required.

Supply route marker with 102mmx102mm cast iron, spike 5mm thick with inscription 'LT Cable, there on bolted / welded to 35x35x6mm angle iron 60cm long and fixing the same in ground as required.

Supplying, laying and jointing of the following sizes of double wall corurgated (DWC) pipes made out of HDPE conforming to IS 14930 Part II for mechanical protection to underground power cables with all required accessories in hard soil 0.75m below ground level including excavation

40 / 32 mm or nearest size

Supply and fixing the following sizes of PVC Conduit conforming to IS 9537 / 1983 part III along with all required accessories on existing pole/ concrete etc. as service/protection pipe as required

32 mm dia light gauge

Supply and providing plate earthing as per IS 3043 with 600x600x6.30 mm GI/CI earth plate ,20 mm GI watering pipe fixed to the earth plate with 20 x 3 mm GI clamps, GI funnel with weld mesh, filling required quantity of charcoal including construction of inspection chamber with a bed concrete of 1:4:8 PCC using 40 mm broken stone (10 cm thick), brick work in cement mortar l:6, plastering the surface of brick masonary and the exposed surface of PCC bed with cement mortar l:4, 12 mm thick, (the finished inside dimension shall be 300 x 300 x 300 mm) but excluding test joint, earth continuity conductor to the plate, and covering at the top. (in ordinary soil.

Supply and providing the following sizes of cast iron gully trap with covering at the top of the inspection chamber of earth pit as required

300 x 300 x 6 mm cast iron gully trap with covering

Supply and providing test joint for the earthing system using 2 Nos of the following sizes of strips including cutting and bending to shape, drilling necessary holes and fixed to the watering pipe etc as required.

2x25 x 3 mm GI strip

Supply and providing earth lead from the test joint to the earth electrode using the following sizes of conductors/ strips including cutting, drilling necessary holes (in case of strip) and fixing firmly with plate test ioint etc as required.

25 x 3 mm GI strip

Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required.

3.15 mm copper conductor (10 SWG)

25 x 3 mm GI strip

Supply of superior quality copper earth socket for the following sizes of earth conductor including crimping etc. as required.

3.12 mm (10SWG)

Supply and providing thefollowing sizes of bolt and nut with washers on the existing MS box i earth bus etc. as required including drilling necessary holes as required

25 x 6mm brass bolt & nut

25 x 8 mm GI bolt & nut

Fabrication, supply and conveyance and installation of name board with Granite stone with requird inscriptions such as scheme and the required names etc. supported by using suitable size angle iron frame work including painting and fixing the whole near the high mast pole as required including two nos photograps

Charges for KSEB connection including all laison works (Actual Amount paid on production of receipt).

R.G.ELECTRONICS