SPECIAL REPAIR TO MI ROOM (BLDG NO-198) AT DEFENCE LAB JODHPUR

Amount

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins arches, pillers etc but excluding ashlar facings, dressed stone work and precast concrete articles and removal of unserviceable materials, debris and rubbish to a distance not exceeding 100m complete all as specified & directed by Engineer-in-charge.

M&L for squared rubble stone walling jodhpur type regular courses well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified and directed by Engineer-in-charge.

M&L for squared rubble walling Jodhpur type, regular courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) except stone complete all as specified & directed by Engineer-in-charge.

Extra over stone walling for hammer dressing to face stones with maximum depression on face from a straight edge not exceeding 40mm & dressing face beds and joints as specified to random rubble walling uncoursed or brought up to courses complete all as specified & directed by Engineer-in-charge.

Racking out joints/ pointing to squared rubble masonry built in cement mortar or cement lime mortar, coursed or uncoursed in walls not less than 12mm deep, washing the joints, removing rubbish off the premises and keeping the surface to pointed or plastered wet for two days prior to re-pointing or plastering complete all as specified & directed by Engineer-in-charge.

M&L for keyed pointing in cement mortar (1:3) to squared rubble masonary coursed or un coursed jodhpur type complete all as specified & directed by Engineer-in-charge.

Demolition of reinforced cement concrete of any description and in any position not other wise specifically provided and removal of unserviceable materials, debris and rubbish to a distance not exceeding 100m complete all as specified & directed by Engineer-in-charge.

M&L for Mild steel TMT bars 10mm dia and over as in reinforcement cut to length bent to shape required including bending,cranking and hooking ends and binding with and including MS wire (annealed) not less than 0.90mm dia complete all as specified & directed by Engineer-in-charge.

M&L for Mild steel TMT bars 6 to 8 mm dia as in reinforcement cut to length bent to shape required including bending,cranking and hooking ends and binding with and including MS wire (annealed) not less than 0.90mm dia complete all as specified & directed by Engineer-in-charge.

M&L for reinforced cement concrete (1:2:4) type B-1 using 20mm graded crushed stone aggregate as in pillars, plinth beam, lintel beam etc, for boundary wall/ compound wall and similiar works complete all as specified & directed directed by Engineer-in-charge.

Form work to sides of pillars, post, struts, plinth beam, lintel beam etc, for rough finished concrete surfaces all as specified & directed by Engineer-in-Charge.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floors & roofs n exc 20cm wide & sides of RCC/PCC bands in walls, horizontal or sloping, & similar work exc 10cm but not exc 20cm wide complete all as specified & directed by Engineer-in-Charge.

Supply only precast cement concrete louvres and jallies, 1:2:4 Type B0 using 12.5 mm graded crushed stone aggregate 50 mm thick (measured solid), including all moulding complete all as specified & directed by Engineer-in-charge.

Fixing only for precast cement concrete louvres and jallies, and set in cement mortar 1:4 complete all as specified & directed by Engineer-in-charge.

Taking down steel gate from boundary wall and compound wall etc and refixing the same after welding and refixing holdfasts complete all as specified and directed by Engineer-in-charge.

Taking down cement or cement lime plaster, any description on brick or stone walls/RCC facia & chajjas etc including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off the premises and leaving the work clear of any plastering complete all as specified & directed by Engineer-in-charge.

M&L for 15 mm thick , plaster in cement mortar (1:4) on stone masonry wall/RCC facia & chajjas surfaces or surfaces other than fair faces of stone work or one side of lathing and finishing the surface even and smooth without using extra cement complete all as specified & directed by Engineer-in-charge.

M&L for 15 mm thick , plaster in cement mortar (1:6) on stone masonry wall surfaces or surfaces other than fair faces of stone work or one side of lathing and finishing the surface even and smooth without using extra cement complete all as specified & directed by Engineer-in-charge.

M&L for rendering 5 mm thick plaster in cement mortar (1:3) on concrete surfaces of ceiling and finishing the surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L for preparing new plastered surfaces of walls and applying two coats of acrylic weather coats exterior grade paint over a coat of primer complete all as specified & directed by Engineer-in-charge.

M&L for preparing old decorated surfaces of stone walls (RCC projected beam/slabs/chajjas etc by complete removal of existing treatment and applying two coats of acrylic weather coats exterior grade complete all as specified & directed by Engineer-in-charge.

M&L preparing new plastered surface of wall and applying 2 to3 mm thick birla white wall care putty complete all as specified & directed by Engineer-in-Charge.

M&L preparing old plastered surface of wall by removing complete removal of existing treatment and applying 2 to3 mm thick birla white wall care putty complete all as specified & directed by Engineer-in-Charge.

M&L for two coats of oil bound distemper of approved tint over and including a coat of primer on putty finished wall surface complete all as specified & directed by Engineer-in-Charge.

M&L for two coats of oil bound distemper of approved tint over and including a coat of primer on newly plastered ceiling surface complete all as specified & directed by Engineer-in-Charge.

M&L for one coat of oil bound distemper of approved tint over old plastered ceiling surface complete all as specified & directed by Engineer-in-Charge.

M&L for preparing old plaster/ concrete/stone surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soof, moulds, moss and efflorescent salts and trading oil and greasing spots and applying two coats of cement base paint complete all as specified & directed by Engineer-in-charge.

Demolition floor hearth or wall tiling including cement mortar bedding and backing coat and removing unserviceable materials, debris and rubbish to a distance not exceeding 100m complete all as specified & directed by Engineer-in-charge.

M&L coloured glazed ceramic tiles size 450 x 300 x 7mm thick on vertical surface of wall over and including 10mm thick backing coat in CM 1:4 set and jointed in neat cement slurry and pointed in white cement / coloured cement to match the tiles complete all as specified & directed by Engineer-in-Charge

Demolition of cement concrete unreinforced in ground floors and pavings ,roof padding including roof treatment, granite flooring, tiles flooring and pavings not exceeding 15cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m complete all as specified & directed by Engineer-in-charge.

M&L 25mm thick PCC 1:2:4 type B-0 using 12.50 mm graded crushed stone aggregate as in base for screed etc, complete all as specified & directed by Engineer-in-charge.

M&L light shade, vitrified tiles, 10mm thick (minimum), (square/ rectangular polished, area of each tiles exceeding 0.36 Sqm (including 600mmx600mm size) but not exceeding 0.42 Sqm, in flooring set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles and over & including 15mm thick screed bedding in CM 1:4 complete all as directed by Engineer-in-charge.

M&L for vitrified tiles of light shade, 10mm thick (minimum) (square/ rectangular) polished area of each tiles equal to or exceeding 0.36 Sqm but not exceeding 0.42 Sqm,cut to size as required in skirting/dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour tiles over and including 10 mm thick rendering with CM 1:4 complete all as specified and directed by Engineer-in-charge.

M&L for 18 to 20mm thick granite (of any type) work (table rubbed and polished) in steps,jambs,pillars,window-cills,cooking platforms and like set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15 mm thick screed bed and rounding to edges of granite slab where required like steps,cooking plate form etc complete all as specified & directed by Engineer-in-charge.(Note:- colour and shade as approved by Engineer-in-charge.)

M&L for 18 to 20 mm thick granite set in (of any type) work (table rubbed and polished) for wall lining (veneering to wall) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 10 mm thick backing coat in cement mortar 1:3 complete all as specified & directed by Engineer-in-charge.

M&L for Udaipur green marble stone slabs 15 to 20 mm thick as in floors,steps,etc including rounding to edge of marble slab as required and pointing with white cement (1:2) using marble dust with admixture of pigment to match with colour of marble slab over & including 15 mm thick screed bed in CM 1:4 complete all as specified and directed by Engineer-in-charge.

M&L for plain cement concrete (1:4:8) type D-2 using 40 mm graded crushed stone aggregate as in foundation, filling and mass concrete all as specified & directed by Engineer-in-charge.

M&L for 75 mm thick PCC (1:3:6) type C 2 using 40 mm graded crushed stone aggregate laid in alternative bays as in plinth protection including finishing the surface even & fair including cutting and filling the joints with mastic filling i.e one part of bitumen 85/25 and 3 parts of sand by weight all as specified & directed by Engineer-in-Charge

M&L plain cement concrete 1:2:4 type B-0 using 12.50 mm graded crushed stone aggregate cast in situ in lintels up to 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, water through and the like including weathering, slightly rounded or chamfered angles and throating including use of form work straight or curved) complete all as specified & directed by Engineer-in-charge.

M&L for coloured chequered cement concrete tiles 25cmx25cmx20-25 mm thick, with grey cement and pigments, set, jointed with neat cement slurry and pointed with white cement and pigment to match the colour of tiles as in floors/ path etc over and including screed bed or bedding layer of 20mm thick in CM (1:4) all as specified and directed by Engineer-in-charge.

Dismantling boarding of any description fixed in any position with nails, complete all as specified.

S&F Gypsum board 12mm thick in ceilling fixed with screw as per manufacturer's instructions, plain/ fixed with steel snap grid(powder coated bottom side) colour GI frame work for seamless ceiling comprising of GI parameter channel 0.55 mm thick with two uneaqual glanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm c/c /intrmediate channel 0.9 mm thick having two equal glanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm c/c with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 mtr length) of 0.55 mm thickness having kurled web of 50 mm and flenge of 26 mm each with lips of 10.5 mm fixed to the interediate channel with connecting clips across the intermediate channels at 457 mm centre to centre with Hangers 6 mm dia GI (upto 1200 mm length) adjusing level fixed to roof slab by means of ceiling claet made out of GI flat 40x 3 mm size 60 mm long & applying two coats of plastic emulsion paint over coat of primer(tint as approved by Engineer-in-charge) (Note:- If any minor electricial fittings and fixtures disturbed there-in after be match and fixed as existing.)

Taking down chowkats or frames (without taking of shutters from the frames) area not exceeding 1.5 Sqm each complete all as specified & directed by Engineer-in-charge.

Taking down chowkats or frames (without taking of shutters from the frames) area exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified & directed by Engineer-in-charge.

Taking down shutters of any description area exceeding 1.0 Sqm but not exceeding 2 Sqm each complete all as specified and directed by Engineer-in-charge.

Refixing shutters of any description in same opening area exceeding 1.0 Sqm but not exceeding 2 Sqm each complete all as specified and directed by Engineer-in-charge.

Taking down shutters of any description area exceeding 2.0 Sqm each complete all as specified and directed by Engineer-in-charge

Refixing shutters of any description in same opening area exceeding 2.0 Sqm each complete all as specified and directed by Engineer-in-charge.

S&F Pressed steel frames (1.25mm sheet thickness) for doors with one or more rebates including necessary fixing lugs , hinges, lock plate, etc., size of frame 125mm x 60 mm including one coat of red oxide primer complete all as specified and directed by Engineer-in-charge.

S&F IInd class hard wood 35mm thick Factory made plain framed panelled shutter any number of panels of timber flat on both sides, with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces the size of rail and stile as per IS 1003 (Part-I) kiln seasoned and chemically pressed treated complete all as specified and directed by Engineer-in-charge.

S&F 35mm thick factory made 2nd class HW glazed and skelton shutter and open rebated and prepared to receive glass, gauge etc (without sash bars), edges or framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR Part-I Section 8 Clause 8.24 (a) complete all as specified and as directed by the Engineer-in-charge.

S&F Mild steel butt hinges 100mm long, medium weight, cold rolled mild steel fixed to steel frame complete all as specified and directed by Engineer-in-charge.

S&F aluminium anodised handles 150 mm long fixed to doors all as specified and directed.

S&F aluminium anodised tower bolts 200 mm long fixed to doors all as spescified and directed.

S&F 250mm long aluminium alloy anodised, sliding door bolt with hasp,staple (bolt type) and fix clips of sheet,cast of extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy all as specified and directed.

M&L preparing new or previously untreated wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over a coat of pink primer complete all as specified and directed by Engineer-in-charge.

M&L preparing old painted wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint (Approved tint) complete all as specified & directed by Engineer-in-charge.

S&F rolled mild steel sections like angle, channel, flat etc as inframed work such as grills,gratings,etc,with ends of bars shouldered and/or riveted,or forged into spikes, framed guard bars;barred iron doors;ladders ;framed balusters;walk ways; railings;framedwork of water tanks,hold fast,wall ties andsimilar work confirming toFe-290Gde E-165 complete all as specified & directed by Engineer-in-charge.

S&F steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay complete with glazing bars, dovetailed or welded complete all as specified & directed by Engineer-in-charge.

S&F steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay complete without glazing bars, dovetailed or welded complete all as specified & directed by Engineer-in-charge.

Taking down collapsible steel gate of area not exceeding 15 sqm and refixing after repairing like remove band,welding,change of rollers etc including greasing complete all as specified & directed by Engineer-in-charge.

S&F Collapsible steel gates,top hung,consisting of channel pickets,pivoted flat bars,top and bottom runners,brass handles etc., as specified,erected in position and securing runners with holdfasts and brackets,including taking down old un-serviceable collapsible steel gate complete all as specified and directed by Engineer-in-charge.

M&L for preparation of new or previously untreated steel surface of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red- oxide, primer complete all as specified & directed by Engineer-in-charge.

M&L for one coat of synthetic enamel paint over old steel surface of any description over 10cm in width or girth not otherwise described complete all as specified & directed by Engineer-in-charge.

M&L for Welding of steel window with hinges or peg stay, sash bar steel handle,butt hinges to door/window chowkats including drilling to frames, guard bars etc complete all as specified and directed by Engineer-in-charge.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified & directed by Engineer-in-charge.

S&F, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specifications & complete all as specified and directed by Engineer-in-charge.

S&F, 100mm size, stainless steel butt hinges, complete all as specified & directed by Engineer-in-charge.

S&F 150 mm size aluminium anodised barrel tower bolts of extruded section complete all as specified & directed by Engineer-in-charge.

S&F 100 mm size aluminium handle, cast type, anodiesed complete all as specified & directed by Engineer-in-charge.

S&F Anodised aluminium frame for doors,windows,ventilators with one or more rebated including jointing cleat for fixing etc complete all as specified and directed by Engineer in charge.

S&F anodised aluminium door shutters,aluminium section weight 1.00 to 1.80 kg/m including necessary jointing cleats,glazing clips,rubber neoprene packing, Aluminium 200 mm handles 2 Nos in each door, SS 100mm hinges,anodised aluminium snap beading screws etc complete all as specified & directed by Engineer-in-charge. (Note :- Floor door spring & sheet glass shall be measured and paid seperately).

S&F anodised aluminium window and ventilator shutters,side hung type without sash bar,aluminium section weighting 1.00 to1.80 kg/m including necessary jointing cleats,glazing clips,rubber packing,anodised aluminium snap beading,screws etc anodised aluminium fittings and SS hinges 100 mm long (02 Nos)Aluminium tower bolt 100 mm long (02 Nos) and handle 150 mm long (02Nos) on each shutters, complete all as specified & directed by Engineer-in-charge. (Note :- sheet glass shall be measured and paid seperately).

S&F Anodised aluminium grill 6mm aluminium section having square gap of 50 mm with U clip (weight not less than 0.50Kg per sqm) complete all as specified and directed by Engineer-in-charge. (Make:- Deco grill or equivalent)

S&F 12 mm thick prelaminated particle board/ MDF board exterior grade, prelaminated both side with decorative choice lamination fixed with screws to timber frame work/aluminium frame complete as specified and directed by Engineer-in-charge.

S&F 100 mm size 4 Levers, brass mortice Lock, vertical type complete all as specified & directed by Engineer-in-charge.

S&F in repairs 140mm Floor door stopper of aluminium alloy body and tongue,anodised,with hard drawn steel spring,fixed in floor complete all as specified & directed by Engineer-in-charge.

S&F in repairs Aluminium(Die cast)body Door closer hydraulically regulated,designation No3,universal type,suitable for shutters of 851 to 1000 mm in width and of weight between 61to 80 Kg complete all as specified & directed by Engineer-in-charge.

S&F in repairsDouble action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box,main body with stainless steel cover,governing pivot made of brass,other parts made of mild steel heavy duty and making good to floor to match with existing floor complete all as specified and directed by Engineer-in-charge.

Hacking out old broken glasses (any thickness, size, quality or description) from steel/wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads etc complete all as specified & directed by Engineer-in-charge.

S&F 3mm thick, sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sqm in each panes complete all as specified and directed by Engineer-in-charge.

S&F 4.80 mm thick sheet glass, ordinary quality and glazing in squares area exceeding 0.5 Sqm in each pane complete all as specified & directed by Engineer-in-charge.

S&F 5.50 mm thick tinted sheet glass, ordinary quality and glazing in squares area exceeding 0.5 Sqm in each pane complete all as specified & directed by Engineer-in-charge.

S&F Solar control film 50 micron reflective type (Make:- Graveware sun control or equivalent) complete all as specified & directed by Engineer-in-charge.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified & directed by Engineer-in-charge.

S&F in repairs,Harrison rails,mild steel,chromium plated with fixing brackets, stops,rollers etc complete all as specified and directed by Engineer-in-chage.

Demolition and breaking up drain pipes (Salt glazed ware, AC,PVC or reinforced concrete) of 75mm/110mm bore set in cement mortar complete all as specified and directed by Engineer-in-charge.

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors as waste & vent pipes complete all as specified & directed by Engineer-in-charge.

S&F PVC (SWR) bends any radius 110 mm bore with access door complete all as specified & directed by Engineer-in-charge.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors as waste & vent pipes complete all as specified & directed by Engineer-in-charge.

S&F PVC (SWR) bends any radius 75mm bore with access door complete all as specified & directed by Engineer-in-charge.

S&F PVC (SWR) multi floor trap with grating including jointing with solvent cement 75mm complete all as specified & directed by Engineer-in-charge.

M&L 125mm/110mm dia PVC (SWR) gully trap, setting & jointing with solvent cement complete all as specified & directed by Engineer-in-charge.

Cutting chases for concealed water tubing and making good in CM 1:3 on brick wall cutting n.exc 10 Cm in girth.

Taking up or down 15 mm bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-charge.

S&F 15 mm bore galvanised iron tubing ISI Marked 'Medium Grade' with all fittings laid in floors or fixed to wall complete all as specified and directed by Engineer-in-charge.

Fixing only 15 mm bore galvanised iron tubing ISI Marked 'Medium Grade' with all fittings laid in floors or fixed to wall complete all as specified and directed by Engineer-in-charge.

Taking up or down 20 mm bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-charge.

S&F20mm bore galvanised iron tubing ISI Marked 'Medium Grade' with all fittings laid in floors or fixed to wall complete all as specified and directed by Engineer-in-charge.

Fixing only 20 mm bore galvanised iron tubing ISI Marked 'Medium Grade' with all fittings laid in floors or fixed to wall complete all as specified and directed by Engineer-in-charge.

S&F in repairs bib taps, cast copper alloy chromium Plated, with crutch or butter fly handle, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule complete all as specified & directed by Engineer-in-charge.

S&F in repairs Brass chromium plated Tubular towel rail 20mm dia,D type, 60 cm long between flanges, complete all as specified & directed by Engineer-in-charge.

S&Fin repairs stop cock, fancy type,brass chromium plated, with long shank and cup (concealed type) cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, screwed both ends for 15 mm bore iron pipe or for union complete all as specified & directed by Engineer-in-charge.

S&F in repairs vitreous china squatting pan "Orissa" pattern, size 580 x 440mm white, with integral foot rest (Excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe,lime/cement concretebedding and making good to the floor complete all as specified and directed by Engineer-in-charge.

S&F in repair vitreous china wash basin white, flat back of size 550 x 400 mm white including waste fittings, brass, chromium plated, coupling, waste pipe, brackets including cutting for and pinning in ends of brackets errect stand, fixing waste pipe complete all as specified & directed by Engineer-in-charge.

S&F in repairs CP pillar cock auto closing system with bottom flange of 15mm dia bore for wash hand basin any type screwed down for iron pipe and fixed with cheknut/washers as required including taking down old un-serviceable pillar tap complete all as specified & directed by Engineer-in-charge. (Make:Jaquar-Model cat part No-PRS-CHR-031 or equivalent as approved by AGE (I)

S&F in repairs ceramic laboratory sink( white ) rectangular shape complete with including CP waste coupling of size 32/40mm and connecting to GI pipe 25mm dia upto floor trap to flow of waste water incl fittings like GI union/reducer/bend/tee/washers/plugs if necessary complete fixing in granite platform with necessary cutting/holes and finishing joints with cement or adhesive to make the surface clean & good appearance ,overall size of sink 24"X18"X10" complete all as specifed & directed

S&F in repairs Brass CP mixer of 15mm dia bore for mixing hot & cold water(double lever) screwed down for iron pipe and fixed in granite top including making hole in granite slab fixing with cheknut/washers as required complete all as specified & directed.

S&F in repairs PTMT Liquid soap container fixed with brass chromium plated screws (As per sample kept in AGE B/R office) complete all as specified & directed by Engineer-in-charge.

S&F in repairs vitreous china EWC (Excluding flushing cistern and flush pipe) complete all as specified & directed by Engineer-in-charge.

S&F in repairs CP brass water jet spray suitable for EWC complete all as specified & directed by Engineer-in-charge.

S&F, in repair, brass chromium plated angle valve for 15mm bore pipe complete all as specified & directed by Engineer-in-charge.

S&F, in repair, white/ black plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed by Engineer-in-charge.

S&F in repairs 15 mm bore brass chromium plated angular stop cock with wall flange(2in1), complete all as specified & directed by Engineer-in-charge.

S&F stainless steel toilet paper with cutting edge cover (As per sample kept in AGE B/R office) complete all as specified and directed by Engineer-in-chage.

S&F in repairs PVC valveless, syphonic action type, flushing cistern, 10 ltrs capacity, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified & directed by Engineer-in-charge.

S&F in repairs vitreous china urinal,Half stall type,white including cantilever brackets,flush pipe,waste coupling,waste pipe 40mm,spreader etc complete all as specified & directed by Engineer-in-charge.

Dismantling of old un-serviceable PVC/RCC water tank of 500 to 1000 ltrs capacity complete all as specified & directed by Engineer-in-charge.

S&F 1000 ltrs capacity rotational moulded polythene water storage tanks (ISI marked) (Cylinderically vertical with closed top) hoisted and fixed in postion all as specified in SSR Part-I complete all as specified and directed by Engineer-in-charge.

S&F in repairs 20mm bore Gun Metal,globe or gate valve with iron wheel head screwed both ends for 20 mm bore GI tubing complete all as specified & directed by Engineer-in-charge.

S&F in repairs 15 mm bore Gun Metal,globe or gate valve with iron wheel head screwed both ends for 15 mm bore GI tubing complete all as specified & directed by Engineer-in-charge.

M&L plain cement concrete 1:2:4 type B-0 using 12.5 mm graded crushed stone aggregate over roof for making good depression/ undulation to match the existing as filling in depression of roof slab surface and rounded at joints of wall with water proofing compound.complete all as specified and directed by Engineer-in-charge.

M&L for 10 mm thick cement plaster with CM(1:3) mixed with water proofing compound as per manufacturers instruction on roof surfaces finished surface even & smooth without using extra cement when concrete is green complete all as specified and directed by Engineer-in-charge. (Note:WPC will be measured & paid separately under respective item of this schedule)

M&L for laying APP membrane as per instruction given below. (a) Preparation of surface and applying one coat of ploymeric primer @ 0.30 Kg/Sqm then applying polymeric bitumen 85/25 @ 1.20Kg/Sqm (b) Supply and providing polymeric water proofing membrane 3mm thick of weight not less than 3.60 kg/sqm, reinforced with polyster non- woven fabric (weight not less than 150 gms/sqm ) centre core including coating the surface with the compatible primer and torch application of membrane with overlaps as per SSR required thereof, complete all as specified and directed by Engineer-in-charge. (c) Applying one coat of polymeric modified bitumen 85/25@ 1.20 kg/sqm over which one coat of aluminium bituminuous paint @ 0.20 kg/sqm shall be applied. Note: - The work of water proofing treatment shall be got executed through expert team of manufacturer or authorised applicator of manufacturer after approval from Engineer-in-Charge.

M&L for 15mm thick screed bed in CM 1:4 on concrete surface, finished even and smooth without using extra cement mixed with water proofing compound as per manufacturer's instructions.complete all as specified and directed by Engineer-in-charge.(Note:- WPC shall measured and paid seperately)

M&L for laying cool roof vitrified tiles of size 300x300x10mm thick (light colour) fixed with spacers over 6mm thick high polymer modified grey cement based tile adhesive and grouted with epoxy grout complete all as specified and directed by Engineer-in-charge.

Supply only liquid integral water proofing compound confirming to IS. Make:- (Pidilite industries/ Fosroc/STP).

Complete removal of strains, dirts, & insoluble black/white bloom visible on the surface of stone masonary walls finished by any type of joints (flush/key/butt/grooved) as per site with proper effective cleaning including washing thorougly with fresh water complete all as specified & directed by Engineer-in-Charge

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern as on roof coverings complete all as specified and directed by Engineer-in-charge.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall,fixed with shelf tapping screws complete all as specified and directed by Engineer-in-charge.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc making good disturbed surfaces of walls, floors, etc complete all as specified and directed by Engineer-in-charge.

Material and Labour for point wiring, wire drawn through in PVC heavy duty conduit pipe and with 1.5 Sqmm FRLS PVC insulated (red for phase and black for neutral) unsheathed, multi stranded copper conductor 1100 voltage grade cable and 1.5 sqmm green in colour PVC insulated solid copper conductor cable for earth continuity connected to common earth bus bar incl factory made metal sheet terminal Modular box flush type with modular cover plate required as per site conditions, flush type with silver colour plastic cover plate including metal modular frame (required as per site condition) for mounting fitting such as switches, sockets, fan regulators, bell push etc and including all other fixing accessories for one light/fan point controlled by one switch complete all as specified and directed by Engr-in-Charge.

All as per item above but for one socket outlet 15 amp on independent board with 2.5 Sq. mm cable and 2.5 Sq.mm. earth wire as approved complete all as specified and directed by Engr-in-Charge.

All as per item No 133 above but 5 Amps 3 pin outlet socket 5 Amps on same board complete all as specified and directed by Engr-in-Charge.

Fixing only ceiling fan/exhaust fan any sweep and any size complete all as specified and directed by Engr-in-Charge.

S&F PVC ceiling rose isolated body complete all as specified and directed by Engr-in-Charge.

S&F Modular Fan regulator 120W- 2 Module and all as specified and directed by Engr-in-Charge.

S&F LED Tube Light fitting & fixture 18 Watt with Cat No : LCTL-18-CDL Make : Crompton and all accessories and all as specified and directed by Engr-in-Charge.

S&F Modular switch piano flush type button single pole one way 6 amps as complete all as specified and directed by Engr-in-Charge.

S&F Modular switch socket combination 2 in 1, 3 pin, 5 and 15 Amps flush type universal complete all as specified and directed by Engr-in-Charge.

S&F Modular switch socket combination 3 pin, 5 Amps flush type universal complete all as specified and directed by Engr-in-Charge.

S&F Lamp Holder Polycarbonate type with back plate suitble for batten fittings complete all as specified and directed by Engr-in-Charge.

S&F of LED light Recessed full open 2x2 tile of 36 Watt Cat No :LCTLRN-36-FO-CDL Make : Crompton complete all as specified and directed by Engr-in-Charge.

S&F Slim design 12W LED recessed round down lighter with superior light out put and integral driver Cat No : LSDE-12-CDL. Make : Crompton complete all as specified and directed by Engr-in-Charge.

S&F Bulk Head fitting 1x9 watt luminaries, with lamp holders, etc complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V, 50 Hz.in die cast aluminium housing & frosted glass with LED Bulb 9 Watt.Cat No : LHKL01160099. Make : Havells complete all as specified and directed by Engr-in-Charge.

M & L for Earthing complete with galvanised steel earth plate electrode 60x60cmx6.3mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top dge of the plte not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in Electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion complete all as specified and directed by Engr-in-Charge.

Taking down sub main any size complete all as specified and directed by Engr-in-Charge.

M&L Sub main wiring with 2 Nos x 4Sqmm single core starnded copper conductor cable FRLS PVC insulated and unsheathed cable incl one 4 Sqmm single core solid cable for continuous earthing drawn through including PVC non-metalic heavy duty rigid conduit, including taking out old one, all as specified and directed by Engr-in-Charge.

Taking down unserviceable Main switch/DBs any type/any size complete all as specified and directed by Engr-in-Charge.

Supply and fixing of MCB DB made of sheet steel phos phatised, powder painted with bus bar, neutral link, earth bar and Din rail , 240 Volts SPN with 4 way double door and all as specified and directed by Engr-in-Charge.

Supply and fixing Vertical three phase & Neutral (TP&N) Vertical) Distrubution Board 8 way double door made of sheet steel phos platised, powder coated with bus bar, neutral link, earth bar and drain rail 200 amps, 415 volt with provision for (MCCB/ MCB TPN) as incoming with three phase and single phase outgoings, complete with insulated bus bar arrangement Cat No : CSDBMCCB100DD08 Make : Legrand and all as specified and directed by Engr-in-Charge.

S&F MCB TPN 4 pole 415 Volts 63 Amp, 10 KA breaking capacity, thermal class ‘C’ in existing distribution board including connecting up complete. Cat No : 408681 Make: Legrand and complete all as specified and directed by Engr-in-Charge.

S&F connection and testing MCB SPN 240 volt `C' series breaking capacity 10 KA of rating 40-63 Amps. Cat No : 408618 Make: Legrand and complete all as specified and directed by Engr-in-Charge.

S&F connection and testing MCB SP 240 volt `C' series breaking capacity 10 KA of rating 6-32 Amps. Cat No : 408587 Make: Legrand and complete all as specified and directed by Engr-in-Charge.

S&F Modular white cover plate with frame, 4 module .Make : ABB/Anchor/Legrand as complete all as specified and directed by Engr-in-Charge.

S&F Modular white cover plate with frame,3 module. Make : ABB/Anchor/Legrand as complete all as specified and directed by Engr-in-Charge.

S&F Modular white cover plate with frame,6 module. Make : ABB/Anchor/Legrand as complete all as specified and directed by Engr-in-Charge.

S&F SPN enclosure with two pin earth plug socket complete with one single pole MCB 32 Amps and all as specified and directed by Engr-in-Charge.

SNEH CORPORATION

HOODA CONSTRUCTION COMPANY

Shri Maruti Trading Co.

m/s Firoz khan

DEV INDUSTRIES

M/S JAGDAMBA ENTERPRISES